To support high-resolution cases that exceed the width limitation of
a pair of SSPPs, or scenarios that surpass the maximum MDP clock rate,
additional pipes are necessary to enable parallel data processing
within the SSPP width constraints and MDP clock rate.
Request 4 mixers and 4 DSCs for high-resolution cases where both DSC
and dual interfaces are enabled. More use cases can be incorporated
later if quad-pipe capabilities are required.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675418/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-10-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The content of every half of screen is sent out via one interface in
dual-DSI case. The content for every interface is blended by a LM
pair in quad-pipe case, thus a LM pair should not blend any content
that cross the half of screen in this case. Clip plane into pipes per
left and right half screen ROI if topology is quad pipe case.
The clipped rectangle on every half of screen is futher handled by two
pipes if its width exceeds a limit for a single pipe.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/675416/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-9-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Currently, SSPPs are assigned to a maximum of two pipes. However,
quad-pipe usage scenarios require four pipes and involve configuring
two stages. In quad-pipe case, the first two pipes share a set of
mixer configurations and enable multi-rect mode when certain
conditions are met. The same applies to the subsequent two pipes.
Assign SSPPs to the pipes in each stage using a unified method and
to loop the stages accordingly.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/675414/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-8-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Currently, only 2 pipes are used at most for a plane. A stage structure
describes the configuration for a mixer pair. So only one stage is needed
for current usage cases. The quad-pipe case will be added in future and 2
stages are used in the case. So extend the stage to an array with array
size STAGES_PER_PLANE and blend pipes per mixer pair with configuration in
the stage structure.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675412/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-7-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Currently MAX_CHANNELS_PER_ENC is defined as 2, because 2 channels are
supported at most in one encoder. The case of 4 channels per encoder is
to be added. To avoid breaking current WB usage case, use dedicated WB
definition before 4 WB usage case is supported in future.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675410/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-6-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The stage contains configuration for a mixer pair. Currently the plane
supports just one stage and 2 pipes. Quad-pipe support will require
handling 2 stages and 4 pipes at the same time. In preparation for that
add a separate define, PIPES_PER_PLANE, to denote number of pipes that
can be used by the plane.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675408/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-5-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
There are 2 pipes in a drm plane at most currently, while 4 pipes are
required for quad-pipe case. Generalize the handling to pipe pair and
ease handling to another pipe pair later. Store pipes in array with
removing dedicated r_pipe.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/675406/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-4-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Current code only supports usage cases with one pair of mixers at
most. To support quad-pipe usage case, two pairs of mixers need to
be reserved. The lm_count for all pairs is cleared if a peer
allocation fails in current implementation. Reset the current lm_count
to an even number instead of completely clearing it. This prevents all
pairs from being cleared in cases where multiple LM pairs are needed.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/675400/
Link: https://lore.kernel.org/r/20250918-v6-16-rc2-quad-pipe-upstream-4-v16-1-ff6232e3472f@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Several users (including IGT kms_getfb tests) allocate DUMB buffers for
YUV data. Commit 538fa012cb ("drm/msm: Compute dumb-buffer sizes with
drm_mode_size_dumb()") broke that usecase, since in those cases
drm_driver_color_mode_format() returns DRM_FORMAT_INVALID.
Handle the YUV usecase, aligning to 32-bit pixels.
Fixes: 538fa012cb ("drm/msm: Compute dumb-buffer sizes with drm_mode_size_dumb()")
Closes: https://lore.kernel.org/all/vptw5tquup34e3jen62znnw26qe76f3pys4lpsal5g3czwev6y@2q724ibos7by/
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/685197/
Message-ID: <20251103-drm-msm-fix-nv12-v2-1-75103b64576e@oss.qualcomm.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
More xe3p support (Harish, Brian, Balasubramani, Matt Roper)
Make panic support work on VRAM for display (Maarten)
Fix stolen size check (Shuicheng)
xe_pci_test update (Gustavo)
VF migration updates (Tomasz)
A couple of fixes around allocation and PM references (Matt Brost)
Migration update for the MEM_COPY instruction (Matt Auld)
Initial CRI support (Balasubramani, Matt Roper)
Use SVM range helpers in PT layer (Matt Brost)
Drop MAX_GT_TYPE_CHARS constant (Matt Roper)
Fix spelling and typos (Sanjay)
Fix VF FLR synchronization between all GTs (Michal)
Add a Workaround (Nitin)
Access VF's register using dedicated MMIO view (Michal)
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRskUM7w1oG5rx2IZO4FpNVCsYGvwUCaQClhwAKCRC4FpNVCsYG
v88YAQC7cmRpHNEaTPTSBHAtVzMfEG+4b6JWjXAbuhQzd6MZgwD/SXOO2xSc66ks
JFHMzpAi/W1d3UVuj/QiN4PL3NTsjQA=
=L+1S
-----END PGP SIGNATURE-----
Merge tag 'drm-xe-next-2025-10-28' of https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
Driver Changes:
More xe3p support (Harish, Brian, Balasubramani, Matt Roper)
Make panic support work on VRAM for display (Maarten)
Fix stolen size check (Shuicheng)
xe_pci_test update (Gustavo)
VF migration updates (Tomasz)
A couple of fixes around allocation and PM references (Matt Brost)
Migration update for the MEM_COPY instruction (Matt Auld)
Initial CRI support (Balasubramani, Matt Roper)
Use SVM range helpers in PT layer (Matt Brost)
Drop MAX_GT_TYPE_CHARS constant (Matt Roper)
Fix spelling and typos (Sanjay)
Fix VF FLR synchronization between all GTs (Michal)
Add a Workaround (Nitin)
Access VF's register using dedicated MMIO view (Michal)
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patch.msgid.link/aQCl9uJxN6CWJ8Vg@fedora
Since 3D merge allows for larger modes to be supported across 2 layer
mixers, filter modes based on adjusted mode clock / 2 when 3d merge is
supported.
Reported-by: Abel Vesa <abel.vesa@linaro.org>
Fixes: 62b7d68352 ("drm/msm/dpu: Filter modes based on adjusted mode clock")
Signed-off-by: Jessica Zhang <jessica.zhang@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/676353/
Link: https://lore.kernel.org/r/20250923-modeclk-fix-v2-1-01fcd0b2465a@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
YUV formats on this hardware needs scaling for chroma planes. However it
is not implemented for QSEED2 which breaks display pipeline if YUV format
is used (causing partial and corrupted output with PPDONE timeouts).
This patch temporarily disables YUV by switching affected sub-block to
RGB only format list.
Fixes: daf9a92dae ("drm/msm/dpu: Add support for MSM8996")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/682061/
Link: https://lore.kernel.org/r/20251018-b4-dpu-fixes-v1-6-1852278064d0@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
UBWC-related register configuration for writeback is not implemented in
the driver yet but there aren't any checks for non-linear modifiers in
atomic_check. Thus when compressed framebuffer is attached to writeback
connector it will be filled with linear image data. This patch forbids
non-linear modifiers for writeback framebuffers until UBWC support for
writeback is properly implemented.
Fixes: 71174f362d ("drm/msm/dpu: move writeback's atomic_check to dpu_writeback.c")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681922/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-5-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
In _dpu_plane_setup_pixel_ext function instead of dividing just chroma
source resolution once (component 1 and 2), second component is divided
once more because src_w and src_h variable is reused between iterations.
Third component receives wrong source resolution too (from component 2).
To fix this introduce temporary variables for each iteration.
Fixes: dabfdd89ea ("drm/msm/disp/dpu1: add inline rotation support for sc7280")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681921/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-4-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Scaling is not implemented for some type of scalers (QSEED2 and RGB) but
it was unintentionally re-enabled with change below. The remaining
condition in dpu_plane_atomic_check_pipe is not enough because it only
checks for length of scaler block (which is present). This patch adds a
additional check for setup_scaler operation.
Fixes: 8f15005783 ("drm/msm/dpu: move scaling limitations out of the hw_catalog")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681918/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-3-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
The dpu_plane_virtual_assign_resources function might fail if there is
no suitable SSPP(s) for the plane. This leaves sspp field in plane
state uninitialized and later leads to NULL dereference during commit:
Call trace:
_dpu_crtc_blend_setup+0x194/0x620 [msm] (P)
dpu_crtc_atomic_begin+0xe4/0x240 [msm]
drm_atomic_helper_commit_planes+0x88/0x358
msm_atomic_commit_tail+0x1b4/0x8b8 [msm]
commit_tail+0xa8/0x1b0
drm_atomic_helper_commit+0x180/0x1a0
drm_atomic_commit+0x94/0xe0
drm_mode_atomic_ioctl+0xa88/0xd60
drm_ioctl_kernel+0xc4/0x138
drm_ioctl+0x364/0x4f0
__arm64_sys_ioctl+0xac/0x108
invoke_syscall.constprop.0+0x48/0x100
el0_svc_common.constprop.0+0x40/0xe8
do_el0_svc+0x24/0x38
el0_svc+0x30/0xe0
el0t_64_sync_handler+0xa0/0xe8
el0t_64_sync+0x198/0x1a0
Fixes: 3ed12a3664 ("drm/msm/dpu: allow sharing SSPP between planes")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681916/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-2-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Due to condition in dpu_rm_reserve_sspp, RGB SSPPs are only tried when
scaling is requested, which prevents those SSPPs from being reserved if
we don't need scaling at all. Instead we should check if YUV support is
requested, since scaling on RGB SSPPs is optional and is not implemented
in driver yet.
Fixes: 774bcfb731 ("drm/msm/dpu: add support for virtual planes")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/681914/
Link: https://lore.kernel.org/r/20251017-b4-dpu-fixes-v1-1-40ce5993eeb6@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
When in bonded DSI mode, only one PLL in one DSI PHY is used for both
DSI PHYs, meaning that parents of the secondary DSI PHY will use the
primary DSI PHY PLL as parent.
In this case the primary DSI PHY PLL will be set even if the primary
DSI PHY is not yet enabled. The DSI PHY code has support for this
particular use-case and will handle the fact the PLL was already
set when initializing the primary DSI PHY.
By introducing a protected variable pll_enable_cnt in the commit
cb55f39bf7 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared"),
this variable is only initially set to 1 when the DSI PHY is initialized
making it impossible to set the PLL before, breaking the bonded DSI
use case by returning 0 when setting the PLL from the secondary DSI
PHY driver and skipping the correct clocks initialization.
But since it was already possible to set the PLL without enabling
the DSI PHY, just drop the pll_enable_cnt setting from the PHY
enable/disable and simply increment/decrement the pll_enable_cnt
variable from the dsi_pll_enable/disable_pll_bias to make sure any
PLL operation is done with the PLL BIAS enabled.
Fixes: cb55f39bf7 ("drm/msm/dsi/phy: Fix reading zero as PLL rates when unprepared")
Closes: https://lore.kernel.org/all/50a49d72-2b1e-471d-b0c4-d5a0b38b2a21@linaro.org/
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/683688/
Link: https://lore.kernel.org/r/20251027-topic-sm8x50-fix-dsi-bonded-v1-1-a477cd3f907d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-redundant explicit call to
pm_runtime_mark_last_busy().
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-redundant explicit call to
pm_runtime_mark_last_busy().
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add gpu metrics definition which is only a set of gpu metrics
attributes. A field is encoded by its id, type and number of instances.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that DC supports analog connectors, there is nothing stopping
us from using it by default on Bonaire.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VRR is not supported on analog signals.
Don't add freesync modes to analog displays or when
VRR is unsupported by DC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the EDID of an analog display is not available, we can't
know the possible modes supported by the display. However, we
still need to offer the user to select from a variety of common
modes. It will be up to the user to select the best one, though.
This is how it works on other operating systems as well as the
legacy display code path in amdgpu.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This feature is useful for analog connections without EDID:
- Really old monitors with a VGA connector
- Cheap DVI/VGA adapters that don't connect DDC pins
When a connection is established through DAC load detection,
the driver is supposed to fill in the supported modes for the
display, which we already do in amdgpu_dm_connector_get_modes.
Also, because the load detection causes visible glitches, do not
attempt to poll the connector again after it was detected this
way. Note that it will still be polled after sleep/resume or
when force is enabled, which is okay.
v2:
Add dc_connection_dac_load connection type.
Properly release sink when no display is connected.
Don't print error when EDID isn't read from an analog display.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DAC_LoadDetection can be used to determine whether something
is connected to an analog connector by determining if there is
an analog load. This causes visible flickering on displays, so
we only resort to using this when the connected display doesn't
have an EDID.
For reference, see the legacy display code:
amdgpu_atombios_encoder_dac_load_detect
v2:
Only clear corresponding bit from BIOS_SCRATCH_0.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will be reused by DAC load detection.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The BIOS uses this register to write the results of the
DAC_LoadDetection command, so we'll need to read this
in order to make DAC load detection work.
As a reference, I used the mmBIOS_SCRATCH_0 definition from
the amdgpu legacy display code.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VGA connectors don't support any hotplug detection, so the kernel
needs to periodically poll them to see if a display is connected.
DVI-I connectors have hotplug detection for digital signals, and
some analog DVI cables pull up that pin to work with that.
However, in general not all DVI cables do this so we can't rely on
this feature, therefore we need to poll DVI-I connectors as well.
v2:
Call drm_kms_helper_poll_fini in amdgpu_dm_hpd_fini.
Disable/enable polling on suspend/resume.
Don't call full link detection when already connected.
v3:
Encounter CLANG build failure. Remove unused variable:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_irq.c:980:7:
error: variable 'use_polling' set but not used [-Werror,-Wunused-but-
set-variable]
980 | bool use_polling = false;
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prepare for polling analog connectors.
Document the function better.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Analog displays typically have a DDC connection which can be
used by the GPU to read EDID. This commit adds the capability
to probe analog displays using DDC, reading the EDID header and
deciding whether the analog link is connected based on the data
that was read.
Note that VGA has no HPD (hotplug detection), so we need to
to do analog link detection for VGA before checking HPD.
In case of DVI-I, while the connector supports HPD, not all
analog cables connect the HPD pins, so we can't rely on HPD
either.
For reference, see the legacy display code:
amdgpu_connector_vga_detect
amdgpu_display_ddc_probe
DAC load detection will be implemented in a separate commit.
v2:
Fix crash / black screen on newer GPUs during link detection.
Ignore HPD pin for analog connectors.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The dce110_hwseq is used by all DCE hardware,
so add the DAC support here.
When enabling/disabling a stream for a RGB signal,
this will call the VBIOS to enable/disable the DAC.
Additionally, when applying the controller context,
call SelectCRTC_Source from VBIOS in order to
direct the CRTC output to the DAC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We support two kinds of analog connections:
1. DVI-I, which allows both digital and analog signals:
The DC code base only allows 1 encoder per connector, and the
preferred engine type is still going to be digital. So, for DVI-I
to work, we need to make sure the pre-existing link encoder can
also work with analog signals.
1. VGA, which only supports analog signals:
For VGA, we need to create a link encoder that only works with the
DAC without perturbing any digital transmitter functionality.
Since dce110_link_encoder already supports analog DVI-I,
just reuse that code for VGA as well.
v2:
Reduce code churn by reusing same link encoder for VGA and DVI-I.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add analog stream encoders for DCE which will be used when
connecting an analog display through VGA or DVI-I.
Considering that all stream encoder functions currently deal
with digital streams, there is nothing for an analog stream
encoder to do, making them basically a no-op.
That being said, we still need some kind of stream encoder to
represent an analog stream, and it is beneficial to split them
from digital stream encoders in the code to make sure they
don't accidentally write any DIG* registers.
On supported chips there is currently up to 1 analog encoder,
which is DACA. There are references to DACB in some code such
as VBIOS commands and register files but it seems to be
not present on DCE 6 and newer.
Set num_analog_stream_encoder = 1 so that we can support
the analog connectors on DCE 6-10, for now.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a num_analog_stream_encoders field to indicate how many
analog stream encoders are present. When analog stream encoders
are present, create them.
Additionally, add an analog_engine field to link encoders and
search for supported analog encoders in the BIOS for each link.
When connecting an RGB signal, search for analog stream encoders.
The actual DCE analog link and stream encoder is going to be
added in a subsequent commit.
v2:
Add check to see if an analog engine is really supported.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid initializing DDC, HPD, etc. when we know that the link is
not going to be constructed because it has no supported encoders.
This is mainly useful for old GPUs which may have encoders such
as TRAVIS and NUTMEG that are not yet supported by DC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VGA connectors don't have HPD (hotplug detection), so don't
touch any HPD related registers for VGA.
Determine whether hotplug detection is available by checking that
the interrupt source is invalid.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Analog video signals on VGA or DVI-A (analog part of DVI-I)
don't support audio, so avoid calling any audio related
functions on analog signals.
Stereo sync was not set up for analog signals in the legacy
display code either, so there is no loss of functionality if
we omit it from DC for now.
Also add a dc_is_rgb_signal similar to other dc_is_*_signal.
v2:
Added comment to clarify what we mean by RGB in this context.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We will use this for validating the pixel clock when
an analog monitor is connected to VGA or DVI-I connectors.
For reference, see the legacy display code:
amdgpu_connector_vga_mode_valid
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The SelectCRTC_Source command will be used to change which CRTC
should be connected to which encoder.
For reference, see the legacy display code:
amdgpu_atombios_encoder_set_crtc_source
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable the codebase to use encoder_control()
when the encoder engine is one of the DACs.
The BIOS parser already supports calling the DAC1EncoderControl
function from the VBIOS, but it was not exposed anywhere.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Jun Nie
Christophe JAILLET
Dmitry Baryshkov
Rob Clark
Simona Vetter
Jessica Zhang
Vladimir Lypak
Neil Armstrong
Sakari Ailus
Lijo Lazar
Sunday Clement
Timur Kristóf