There have recently been changes that break backwards compatibility,
that were introduced into DMUB firmware (for DCN32x) concerning FPO and
SubVP. So, since those are just power optimization features, we can just
disable them unless the user is using a new enough version of DMUB
firmware.
Cc: stable@vger.kernel.org
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2870
Fixes: ed6e2782e9 ("drm/amd/display: For cursor P-State allow for SubVP")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Closes: https://lore.kernel.org/r/CABXGCsNRb0QbF2pKLJMDhVOKxyGD6-E+8p-4QO6FOWa6zp22_A@mail.gmail.com/
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Allow devs to check raw clk register values by dumping them on the log
[how]
Add clk register dump implementation
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Johnson Chen <johnson.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream so
there is no need to have two flags to control it. Unifying this to a
single flag allows dc_stream_adjust_vmin_vmax to skip actual
programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Revert commit fec05adc40 ("drm/amd/display: Use channel_width = 2 for vram table 3.0")
Because the issue is being fixed from VBIOS side.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Add config to make HPO PG handled in dmubfw ips entry/exit
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, may get apply_idle_optimizations call while DMUB
is inactive which will just time out.
[How]
Set and track power state in dmub_srv and check power state before
sending commands to DMUB. Add interface in both dmub_srv and
dc_dmub_srv
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pm supports return vpe clock table and soc clock table
Signed-off-by: Peyton Lee <peytolee@amd.com>
Reviewed-by: Li Ma <li.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Power up and power down has reverted programming order.
also make sure disable root clock last.
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When we're in a no plane config, DCN is always asserting
P-State allow
- This creates a scenario where the P-State blackout can start
just as VUPDATE takes place and transitions the DCN config to
a one where one or more HUBP's are active which can result in
underflow
- To fix this issue, force p-state disallow and unforce after
the transition from no planes case -> one or more planes active
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
For mode programming we want to extend the prefetch as much as possible
(up to oto, or as long as we can for equ) if we're not already applying
the 60us prefetch requirement. This is to avoid intermittent underflow
issues during prefetch.
The prefetch extension is applied under the following scenarios:
1. We're in prefetch mode 1 (i.e. we don't support MCLK switch in blank)
2. We're using subvp or drr methods of p-state switch, in which case we
we don't care if prefetch takes up more of the blanking time
Mode programming typically chooses the smallest prefetch time possible
(i.e. highest bandwidth during prefetch) presumably to create margin between
p-states / c-states that happen in vblank and prefetch. Therefore we only
apply this prefetch extension when p-state in vblank is not required (UCLK
p-states take up the most vblank time).
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
User interface cannot guarantee system is in
idle state, so need to ensure we exit idle state
before accessing any HW data.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To match the hardware sequence
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Allen <allen.pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dtbclk is unavaliable from pmfw. Try to grab the value from bounding box
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FP guard is valid for all recent asics, not just RV, so fix the comment.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
HostVMMinPageSize is expected to be in KB according to spec,
the checks later down the line reflect this as well.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
With DP2.1a expansion we are allowing DP40 cables to do UHBR13.5
how:
Assume UHBR10 means UHBR13.5 also for unknown cable type and
passive cable type.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ran Shi <ran.shi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a smu_print message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Mark reports that brightness is not restored after Xorg dpms screen blank.
This behavior was introduced by commit d9e865826c ("drm/amd/display:
Simplify brightness initialization") which dropped the cached backlight
value in display code, but also removed code for when the default value
read back was less than 1 nit.
Restore this code so that the backlight brightness is restored to the
correct default value in this circumstance.
Reported-by: Mark Herbert <mark.herbert42@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3031
Cc: stable@vger.kernel.org
Cc: Camille Cho <camille.cho@amd.com>
Cc: Krunoslav Kovac <krunoslav.kovac@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Fixes: d9e865826c ("drm/amd/display: Simplify brightness initialization")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We currently don't support dirty rectangles on hardware rotated modes.
So, if a user is using hardware rotated modes with PSR-SU enabled,
use PSR-SU FFU for all rotated planes (including cursor planes).
Cc: stable@vger.kernel.org
Fixes: 30ebe41582 ("drm/amd/display: add FB_DAMAGE_CLIPS support")
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2952
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Bin Li <binli@gnome.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Does the same thing as:
commit 6740ec97bc ("drm/amd/display: Increase frame warning limit with KASAN or KCSAN in dml2")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311302107.hUDXVyWT-lkp@intel.com/
Fixes: 67e38874b8 ("drm/amd/display: Increase num voltage states to 40")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Alvin Lee <alvin.lee2@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Samson Tam <samson.tam@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
This version brings along following fixes:
* Enable writeback.
* Add multiple fixes for DML2 and DCN35.
* Introduce small code style adjustments.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This simple commit adjusts part of the code style in some of the dc bios
files.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
UBSAN errors observed in dmesg.
array-index-out-of-bounds in dml2/display_mode_core.c
[How]
Fix the index.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
drm_writeback requires to capture exact one frame in each writeback
call.
[HOW]
frame_capture is disabled after each writeback is completed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add a function to enable and disable DWB's frame captures.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Counter j was not updated to present the num of writeback_info when
writeback pipes are removed.
[HOW]
update j (num of writeback info) under the correct condition.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
hw_points_num is 0 before ogam LUT is programmed; however, function
"dwb3_program_ogam_pwl" assumes hw_points_num is always greater than 0,
i.e. substracting it by 1 as an array index.
[HOW]
Check hw_points_num is not equal to 0 before using it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
wb_enabled field is set to false before it is used, and the following
code will never be executed.
[HOW]
Setting wb_enable to false after all removal work is completed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
The enable and disable writeback calls need to be included in the
coressponding functions in dc_stream.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Prepare a virtual connector for writeback.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Virtual stream encoder should not be a free match for thunderbolt or
usbc, and thus should be avoided.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current implementation will choose to use refclk as dscclk. This is not
recommended by hardware team as refclk is a fixed value which could
cause unnecessary power consumption or it could be not enough for large
DSC timings. So we are adding new interfaces so we could switch to use
dynamically generated DSCCLK by DTO. So DSCCLK is programmable based on
current pixel clock and dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In previous case, Replay didn't identify the IRQ type, This commit fixes
the issues for the interrupt.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Missing clock gating programming blocks memory power on from boot up.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Yihan Zhu <yihan.zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching to another HDMI mode, we are unnecesarilly
disabling/enabling FIFO causing both HPO and DIG registers to be set at
the same time when only HPO is supposed to be set.
This can lead to a system hang the next time we change refresh rates as
there are cases when we don't disable OTG/FIFO but FIFO is enabled when
it isn't supposed to be.
[How]
Removing the enable/disable FIFO entirely.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is w/a: we need to keep domain 24 power up in driver side, and let
dmubfw handle it for S0i3. For last display unplugged, if OTG in PG, no
interrupt call back coming.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HW registers were being read to quickly, causing incorrect values to be
logged after a clock frequency was changed
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DC debug options currently do not function for dynamically adjusting
our watermarks.
[How]
Hook them up before passing them to DML2.
Also make sure we're using dc->bb_overrides since dc->debug isn't
populated during dc_construct.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
w/a use case:
- dual display, compliance, toggling between the displays
- switching between 120Hz 420 -> 144Hz 444 and vice versa
- switching between 144Hz -> 60Hz TMDS or vice versa
It'd typically involve TMDS in some capacity since that's the only link
signal we leave the OTG running but DIO/PHY off you can hit this in
cases where you have multiple displays as well it syncs with the first
active OTG, so if you had OTG[0] mapped and FIFO off you'd hit it even
if OTG[1] was mapped and had FIFO
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BIOS FW info version 3.5 is introduced to support new ASICs, but it's
content is currently same as 3.4.
[How]
Include minor version 5 in parsing to enable support.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The is_automated flag logic only applies to USB4 DPIA links during DP LL
compliance test automation. The flag should not be set for non-DPIA
cases.
[How]
Add check for DPIA link endpoint type before setting the flag. Also,
rename is_automated to skip_fallback_on_link_loss for clarity.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VBIOS has suggested to use channel_width=2 for any ASIC that uses vram
info 3.0. This is because channel_width in the vram table no longer
represents the memory width
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changing PBN calculation to be more in line with spec. We don't need to
inflate PBN_NATIVE value by the 1.006 margin, since that is already
taken care of in the get_pbn_per_slot function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rollback to new context for active display: this was previous tested
sequence. Avoid to do OTG master toggle is no active display at all,
this w/a was for fifo err.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We use spatial dither by default for all output bpc (6/8/10). While it
makes some sense for FP16, for ARGB2101010 surfaces it makes little
sense as even if we skip color pipeline to preserve bit accuracy,
spatial dither adds random noise so a few percent pixels are 1 bit off.
This commit chages the 10bpc out dither policy to rounding.
Also, in Polaris/Vega times, policy used to be round for 10bpc out; it
looks like it got inadvertently changed for Navi. Difference is only
detectable with capture cards.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OTG inst and pwrseq inst mapping is not align therefore we cannot use
otg_inst as pwrseq inst to get DCIO register.
[How]
1. Pass the correct pwrseq instance to dmub when set abm pipe.
2. LVTMA control index change from panel_inst to pwrseq_inst.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Phil Hsieh <phil.hsieh@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some registers needed for root clock gating in dcn35 are not defined in
the dccg header.
[How]
Add the needed registers and temporarily disable some register writes
that are now taking place successfully until the registers can be
properly enabled.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Many DCN generations only have two HPO link encoders and therefore only
support driving a max of two DP2 PHYs. DP2 MST hubs currently can not
pass 3x display validation as each downstream sink is enumerated as
separate DP2 output.
[HOW]
Count MST hubs once by treating only 1st remote sink in topology as an
encoder.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When querying DML for a vlevel after pipes have been split or merged the
ODM policy would revert to a default policy, which could cause the query
to use the incorrect ODM status. In this case ODM 2to1 was validated,
but the last DML query would assume no ODM and return the incorrect
vlevel.
[how]
Added ODM check to apply the correct ODM policy before querying DML.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix issue when override level bigger than default. Levels 5, 6, and 7
had zero stutter latency, this is because override level being
initialized after stutter latency inits.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Reviewed-by: Allen Pan <allen.pan@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Optimize fast validation cases to only validate the highest voltage
level. This works because during fast validation we only care if the
mode can be supported or not (at any vlevel).
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During hibernate sequence the source context might not have a clk_mgr.
So don't use it to look for DML2 support.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2980
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A number of DML parameters related to HostVM were either missing or
being set incorrectly, which may cause inaccuracies in calculating
margins and determining BW limitations.
[How]
Correct these values where needed and populate the missing values.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Update DSC DPCD parsing to take granular throughput adjustment into
consideration.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DTBCLK is enabled on idle and it will burn power.
[How]
There's a few issues here:
- Always enabling DTBCLK on clock manager init
- Setting refclk when DTBCLK is supposed to be disabled
- Not applying the correct calculated version refclk, but instead the
base value which might be zero
On dtbclk_en change we'll message PMFW to enable or disable the clock
accordingly.
The DTBDTO will be then based on refclk, but it will be set to the
default fixed value if there was nothing calculated in DML despite the
clock being considered enabled.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Add a new AUX sequence provided by vendor to improve
interop with specific display configurations.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Limit the dynamic crb to dual stream configs that include eDP
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
checkpatch complains that:
WARNING: braces {} are not necessary for single statement blocks
+ if (pool->base.irqs != NULL) {
+ dal_irq_service_destroy(&pool->base.irqs);
+ }
Fixed it by removing unnecessary braces to fix the coding style issue.
Signed-off-by: RutingZhang <u202112078@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Increase the pstate latency to improve ac/dc transition
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We have dynamic power control in driver but
should be ignored when power is forced on.
[how]
Bypass any power control when it's forced on.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a number of instances where we convert HostVMMinPageSize or
GPUVMMinPageSize from bytes to KB by dividing (rather than multiplying) and
vice versa.
Additionally, in some cases, a parameter is passed through DML in KB but
later checked as if it were in bytes.
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Prevent overwrite of dc->config.use_default_clock_table, as it should be
pre-configured.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The new table doesn't have an implicit mapping between Fclk SOC voltage
and MemClk and it currently builds the table off of number of Fclk
states rather than DcfClock states.
The DML table in use is not correct for functionality or power and
does not align with our existing policies for DCN3x.
[How]
Build the table based on DcfClock with the following assumptions:
1. Raising Soc voltage is the most expensive operation, so assume that
running at max DispClock or DppClock is preferable.
2. Assume that we can run at max Fclk / MemClk at any state, but
restrict the maximum state to the very last entry in the table as the
worst case scenario.
3. Assume that Fclk always has a 2x multiplier on DcfClock unless the
table specifies something lower.
Reviewed-by: Taimur Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move all optc files to unique
folder optc.
[how]
creating optc repo in dc, and moved the dcnxx_optc.c and .h files into
corresponding new folders inside the optc and cleared the linkage
errors by adding relative paths in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Handover from DMUB to driver does not perform link rate toggle.
It might cause link training failure for boot up.
[HOW]
Force toggle rate wa for first link train.
link->vendor_specific_lttpr_link_rate_wa should be zero then.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Zhongwei <zhongwei.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- To reduce vlevel further, we can try to apply subvp on
configs that already support p-state since the natural
p-state support may not allow for DPM0.
- Add code to try subvp to reduce UCLK DPM level further
if already supported, but don't use subvp if it does not
optimize the DPM level even lower
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit fcfc6ceec3.
[why]
Flickering observed. Regression search pointed to this being
the offending commit.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some panels with residency period of 2054 exhibit flickering with
Z8 at the end of the frame.
[How]
As a workaround, increase the limit to block these panels.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Flickering occurs on DRR supported panels when engaged in DRR due to
min_dst_y_next becoming larger than the frame size itself.
[How]
In general, we should be able to enter Z8 when this is engaged but it
might be a net power loss even if the calculation wasn't bugged.
Don't support enabling Z8 during the DRR region.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When otg workaround is applied during clock update, otgs of
tiled display went out of sync.
[How]
To call dc_trigger_sync() after clock update to sync otgs again.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Previously SubVP would never be selected on 1080p60 displays because
it has too much vactive margin. However, implement a change to allow
it like how 1440p60 is allowed.
- Add a new struct such that we have a list of allowed modes for
enabling subvp with vactive margin (currently 1080p60 and 1440p60)
- Also ensure to block drr + vblank cases to prevent unexpected
enablement of new display configs
- Update SW cursor fallback for these new potential cases as well
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If Panel max link off frame count is low, it will cause low residency
for Replay, then Disabled timing sync check in Full screen Video Case.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MST relevant variables are maintained at drm side. As the result, we
still have to call drm_dp_remove_payload_part2() to update the relevant
values regardless the link is under mst mode or not. We used to have a
workaround patch to tackle this: commit 3d8fcc6740 ("drm/amd/display:
Extract temp drm mst deallocation wa into its own function")
Now it's time to remove the workaround and adjust the flow.
[How]
During deallocate_mst_payload(), source actually doesn't send out
ALLOCATE_PAYLOAD at the end as like the flow in allocate_mst_payload().
Call function dm_helpers_dp_mst_send_payload_allocation() at the end of
deallocate_mst_payload() is a bit confusing.
Separate dm_helpers_dp_mst_send_payload_allocation() into 2 functions.
Have a new function dm_helpers_dp_mst_update_mst_mgr_for_deallocation()
to replace dm_helpers_dp_mst_send_payload_allocation() for payload
deallocation.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Remove the brightness cache in DC. It uses a single value to represent
the brightness for both SDR and HDR mode. This leads to flash in HDR
on/off. It also unconditionally programs brightness as in HDR mode. This
may introduce garbage on SDR mode in miniLED panel.
[How]
Simplify the initialization flow by removing the DC cache and taking
what panel has as default. Expand the mechanism for PWM to DPCD Aux to
restore cached brightness value generally.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sending certain Frameupdate number for Replay Power Evaluation
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
If during driver init stage there are greater than 20
intermediary voltage states while constructing the SOC
BB we could hit issues because we will index outside of the
clock_limits array and start overwriting data. Increase the
total number of states to 40 to avoid this issue.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently DCN35 does not spread DPREFCLK
[HOW]
Remove hardcoded table with nonzero caps
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Augment the function to allow send different format data in different
use case.
Reviewed-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To refactor DSC and make DSC files unit testable.
[how]
moved the dcnxx_dsc.c and .h files
into corresponding dcn folders inside
the dsc and cleared the linkage errors.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Bhuvana Chandra Pinninti <bhuvanachandra.pinninti@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
When choosing which dummy p-state latency to use, we
need to use the DRAM speed from validation. The DRAMSpeed
DML variable can change because we use different input
params to DML when populating watermarks set B.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong function is used to translate LUT values to HW format, leading to
visible artifacting in some cases.
[How]
Use the correct cm3_helper function.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We've updated the table but the values aren't being reflected in DML2
calculation.
[How]
Pass them into the bbox overrides.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can override SR watermarks but not Z8 ones.
[How]
Add new parameters for Z8 matching the SR ones and feed them into the
states.
These also weren't being applied to every state, so make sure that
we loop over and update all SOC states if given an override.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the new pipe resource management logic, the special handling for
stereo timings is missing.
This commit implements the same stereo timings handling as old
pipe resource management code.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When ODM slice count is changed, otg master pipe's pixel clock params is
no longer valid as the value is dependent on ODM slice count.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In dcn32 DML pipes are ordered the same as dc pipes but only for used
pipes. For example, if dc pipe 1 and 2 are used, their dml pipe indices
would be 0 and 1 respectively. However
update_pipe_slice_table_with_split_flags doesn't skip indices for free
pipes. This causes us to not reference correct dml pipe output when
building pipe topology.
[how]
Use two variables to iterate dc and dml pipes respectively and only
increment dml pipe index when current dc pipe is not free.
Cc: stable@vger.kernel.org # 6.1+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the link requests to skip implicit eDP power control, we should honor
that request.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Update to the new values per HW team request. Affects both stutter
and z8.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML2 means that the dcn3x policy for calculating z-state support
no longer runs from validate_bandwidth.
This means we are unconditionally allowing Z8, the hardware default.
[How]
Port the policy over to DCN35, but with a few modifications:
- Don't use min_dst_y_next_start as a check for Z8/Z10 allow
- Add support for overriding the Z10 stutter period per ASIC
- Cleanup the code to make the policy assignment more clear
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To support dynamic switching for Replay timing sync mechanism.
Reviewed-by: ChunTao Tso <chuntao.tso@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add missing chips for HDCP
- Add new command to disable replay timing resync
- Fix encoder disable logic
- Enable DSC Flag in MST Mode Validation
- Change the DMCUB mailbox memory location from FB to inbox
- Add disable timeout option
- Negate IPS allow and commit bits
- Enable DCN clock gating for DCN35
- Prefer currently used OTG master when acquiring free pipe
- Try to acquire a free OTG master not used in cur ctx first
- Clear dpcd_sink_ext_caps if not set
- Enable fast plane updates on DCN3.2 and above
- Add null checks for 8K60 lightup
- Refactor resource into component directory
- Fix DSC not Enabled on Direct MST Sink
- Guard against invalid RPTR/WPTR being set
- Enable CM low mem power optimization
- Fix a debugfs null pointer error
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver continues running whenever there is
is timeout from smu or dmcub.
It is difficult to track failure state
when dcn, dc or dmcub changes on root failure.
[HOW]
Add disable_timeout option to halt driver
whenever there is a failure in response.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enable DCN clock gating for DCN35.
Disable DTBCLK gate before link training
and re-enable afterwards
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
When acquiring an OTG master pipe we should prefer currently enabled OTG
master pipes first. If there are no free pipes used as current OTG
master pipe then we will try to acquire a currently unused free pipe as
new OTG master instead of tearing down current secondary pipes from ODM
or MPC combine.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The current otg master pipe allocation logic is not optimized based
current resource context. We should try to acquire a free OTG master not
used in cur cts first to avoid unnecessary pipe switch from current
state.
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Move all resource files to unique folder resource.
[HOW]
Created resource folder in dc, moved the
dcnxx_resource.c and dcnxx_resource.h files into
corresponding new folders inside the resource and
made appropriate changes for compilation in Makefiles.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
MPC MCM low mem power optimization still causes color distortion on
first SCE enablement, only forces light sleep for it.
DPP low memory power optimization still needs this bit to save power.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Yihan Zhu <yihan.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DENTIST hangs when OTG is off and encoder is on. We were not
disabling the encoder properly when switching from extended mode to
external monitor only.
[HOW]
Disable the encoder using an existing enable/disable fifo helper instead
of enc35_stream_encoder_enable.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On s0i3, IPS mask isn't saved and restored.
It is reset to zero on exit.
If it is cleared unexpectedly, driver will
proceed operations while DCN is in IPS2 and
cause a hang.
[HOW]
Negate the bit logic. Default value of
zero indicates it is still in IPS2. Driver
must poll for the bit to assert.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some eDP panels' ext caps don't set initial values
and the value of dpcd_addr (0x317) is random.
It means that sometimes the eDP can be OLED, miniLED and etc,
and cause incorrect backlight control interface.
[HOW]
Add remove_sink_ext_caps to remove sink ext caps (HDR, OLED and etc)
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Add some null checks to fix an issue where 8k60
tiled display fails to light up.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Spotted by coccicheck, there is a redundant check for
v->SourcePixelFormat[k] != dm_444_16. This patch will
remove it. The corresponding output follows.
drivers/gpu/drm/amd/display/dc/dml/dcn30/display_mode_vba_30.c:5130:86-122: duplicated argument to && or ||
Signed-off-by: José Pekkarinen <jose.pekkarinen@foxhound.fi>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The member variable enable_hpo_pg_support is already initialized
and hence the reinitialization instruction can be removed. Issue
identified using the doubleinit.cocci Coccinelle semantic patch script.
Signed-off-by: Bragatheswaran Manickavel <bragathemanick0908@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DML2 does not handle the case when we have
a single stream sourcing 2 or more planes
that are duplicates of one another. To properly
handle this scenario, pipe index to plane index
mapping is used to decide which plane is being
processed and programmed.
[how]
Create static array of pipe index to plane index map.
Populate the array properly and use in appropriate places.
Reviewed-by: Xi (Alex) Liu <xi.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Similar to FPO, SubVP should also force cursor P-State
allow instead of relying on natural assertion
- Implement code path to force and unforce cursor P-State
allow for SubVP
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enable the last of the RCO options for dcn35
[How]
Breakout RCO from dccg35_set_physymclk so that
physymclk RCO can be set in dccg_init without
disabling physymclk
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean-up the code to remove references of all unused
dml architecture versions since only dml2 is actively
used.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a case when we are switching from ODM combine to Subvp where
minimal transition based off subvp state is required. In thise case, we
need to save and restore mall state when applying minimal transition.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For all the components that participate in DCN architecture, there is a
header in the dc/inch/hw. For some reason, OPTC broke this pattern and
added all the primary functions/structs associated with that in the
dcn10_optc.h file. For consistency's sake, this commit introduces a new
optc.h file and extracts the code from dcn10_optc to this new file.
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Doing a mode timing change causes a hang when OTG is not disabled.
[how]
Add link_enc null check in disable_otg_wa to cover this case.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current Desync IRQ handler will have some potential do not hit the
desync error case. We change to check both desync error HPD and DPCD.
Signed-off-by: Dennis Chan <dennis.chan@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
Update test link rate DPCD bit field to match spec
Enable RCO options for dcn35
Add missing dml2 init value for dcn35
Enable DCN clock gating
DCN35 Disable cm power optimization
Allow 16 max_slices for DP2 DSC
Fix OTG disable workaround logic
Enable more IPS options
Fix FRL assertion on boot
Fix missing blendTF programming
Update DP HPO MSA with colorimetry from test request
Fix handling duplicate planes on one stream
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For lighting up, some dml2 params needs to be initialized.
One of them escaped initial patch under:
"drm/amd/display: Add DCN35 DML2 support"
[How]
Add missing initialization.
Fixes: 115009d11c ("drm/amd/display: Add DCN35 DML2 support")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DENTIST was hanging when performing DISPCLK update with OTG enabled, as
OTG disable workaround was not executing.
[How]
Workaround was checking against current_state before running, but when
called from optimize_bandwidth (safe_to_lower), we should be checking
against context instead.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For Replay, if we receive HPD, it doesn’t need to reboot the display.
We don’t need to return anything exactly.
[How]
Return nothing just because we don’t need to reboot the display.
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's useful to disable the recovery mechanism when debugging replay
desync errors.
Signed-off-by: Dennis Chan <Dennis.Chan@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Robin Chen <robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Enabling SCE after boot up will cause color distortion.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Yihan Zhu <yihan.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some DP link layer tests request a different colorimetry than the
default one that is used. Currently, our test automation logic does not
update the MSA with the test request value for DP HPO case.
[How]
Update HPO MSA colorimetry with test automation request value.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
An SCR was made to the DP2.0 spec that updated the bit field definition
for UHBR13.5 in the test link rate DPCD register.
[How]
Add new translation to match the SCR update. Keep old translation for
backwards compatibility.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To help isolate static screen and
video playback tests, we want to enable
an IPS option to allow IPS only on D3 cycle.
[how]
Add DISABLE_DYNAMIC and DISABLE_ALL
IPS disable flags for user control.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Enable root clock optimization options for dcn35
for power savings
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Make sure to ungate the clocks on boot
so programming sequence is done successfully.
[how]
Move the ungate logic after bios init.
Reviewed-by: Xi (Alex) Liu <xi.liu@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When MPO surface pixel format is not ARGB8888, fast update can miss
programming blendTF.
[How]
Set the gamma_change update flag on blend_tf change.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
On boot disable domain22 force power on
decouple dmcub execution to reduce lock granularity
Enable fast update on blendTF change
Fix blend LUT programming
Program plane color setting correctly
amend HPD handler for Replay
Avoid NULL dereference of timing generator
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some systems dmub commands run at high IRQ, so long running
commands will block other interrupts.
[How]
Decouple wait_for_idle from dmcub queue/execute/wait.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: JinZe.Xu <jinze.xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP2 enablement fails when domain22 is set to force
power on
[How]
Disable force power on for domain22 on startup
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LUT write index does not get reset to zero when writing the LUT values
for each separate RGB component, which results in wrong data for 2 of
the 3 components.
[How]
Reset LUT write index to zero before writing each component's data.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are some registers for plane
color that are skipped programming
on resume. Need to add those as part
of the sequence.
[how]
Add new function hook for programming
plane color control.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building ARCH=x86_64 allmodconfig with clang, which will typically
have sanitizers enabled, there is a warning about a large stack frame.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c:6265:13: error: stack frame size (2520) exceeds limit (2048) in 'dml_prefetch_check' [-Werror,-Wframe-larger-than]
6265 | static void dml_prefetch_check(struct display_mode_lib_st *mode_lib)
| ^
1 error generated.
Notably, GCC 13.2.0 does not do too much of a better job, as it is right
at the current limit of 2048 (and others have reported being over with
older GCC versions):
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c: In function 'dml_prefetch_check':
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c:6705:1: error: the frame size of 2048 bytes is larger than 1800 bytes [-Werror=frame-larger-than=]
6705 | }
| ^
In the past, these warnings have been avoided by reducing the number of
parameters to various functions so that not as many arguments need to be
passed on the stack. However, these patches take a good amount of effort
to write despite being mechanical due to code structure and complexity
and they are never carried forward to new generations of the code so
that effort has to be expended every new hardware generation, which
becomes harder to justify as time goes on.
To avoid having a noticeable or lengthy breakage in all{mod,yes}config,
which are easy testing targets that have -Werror enabled, increase the
limit for configurations that have KASAN or KCSAN enabled by 50% so that
cases of extremely poor code generation can still be caught while not
breaking the majority of builds. CONFIG_KMSAN also causes high stack
usage but the frame limit is already set to zero when it is enabled,
which is accounted for by the check for CONFIG_FRAME_WARN=0 in the dml2
Makefile.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Check whether assigned timing generator is NULL or not before
accessing its funcs to prevent NULL dereference.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC v3.2.256
Summary:
* Fixes null-deref regression after
"drm/amd/display: Update OPP counter from new interface"
* Fixes display flashing when VSR and HDR enabled on dcn32
* Fixes dcn3x intermittent hangs due to FPO
* Fixes MST Multi-Stream light up on dcn35
* Fixes green screen on DCN31x when DVI and HDMI monitors attached
* Adds DML2 improvements
* Adds idle power optimization improvements
* Accommodates panels with lower nit backlight
* Updates SDP VSC colorimetry from DP test automation request
* Reverts "drm/amd/display: allow edp updates for virtual signal"
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
To enable automated testing through IGT, expose an API that is
accessible through debugfs to query current status of SubVP feature.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[HOW&WHY]
Reading the value from
DP_EDP_BACKLIGHT_MODE_SET_REGISTER, DPCD 0x721
before setting the
BP_EDP_PANEL_LUMINANC_CONTROL_ENABLE bit
to ensure there are no accidental overwrites.
Reviewed-by: Sreeja Golui <sreeja.golui@amd.com>
Reviewed-by: Harry Vanzylldejong <harry.vanzylldejong@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Iswara Nagulendran <iswara.nagulendran@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently causes some DP link layer failures, backing out until
the failures are root caused.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LUT params are not cleared after setting blend TF, which can lead to
same params being used for the shaper, if the shaper func is bypassed.
[How]
Set lut_params to NULL after program_1dlut.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where number of pipes available is less
than num_opp, there will opp instances that are
null
[How]
Add null check to skip over these opp instances
Fixes: 40de8403b9 ("drm/amd/display: Update OPP counter from new interface")
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Provide DCN32 specific sequence and update DCN30 sequence
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Helper function calculates num_ways using 32-bit. But is
returned as 8-bit. If num_ways exceeds 8-bit, then it
reports back the incorrect num_ways and erroneously
uses MALL when it should not
[How]
Make returned value 32-bit and convert after it checks
against caps.cache_num_ways, which is under 8-bit
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit just replaces dc_interrupt_po*r*larity with its correct
name, which is dc_interrupt_polarity.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Bandwidth validation failure on framepack tests.
Need to double pixel clock when 3D format is
framepack. Also for HDMI displays, we need to
keep the ITC flag to 1 by default.
[how]
Double the pixel clock when using framepack 3D format.
Set hdmi ITC bit to 1.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittent reboot hangs are observed introduced by
"Improve x86 and dmub ips handshake".
[How]
Bring back the commit but fix the polling.
Avoid hanging in place forever by bounding the delay and ensure that
we still message DMCUB on IPS2 exit to notify driver idle has been
cleared.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Unify pipe resource management logic in dc resource layer.
V2:
Add default case for switch.
CC: Hamza Mahfooz <hamza.mahfooz@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need DML2 to support new pipe resource management APIs.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Currently set_default_brightness_aux function uses 5 nits as lower limit
to check for valid default_backlight setting. However some newer panels
can support even lower default settings
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Swapnil Patel <swapnil.patel@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain test equipment vendors check the SDP VSC for colorimetry against
the value from the test request during certain DP link layer tests for
YCbCr test cases.
[How]
Update SDP VSC with colorimetry from test automation request.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
V2:
Add function hooks for set and get idle states.
Check if function hook was properly initialized.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1288d70208.
Causes intermittent hangs during reboot stress testing.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn35 misses .enable_symclk_se hook that makes MST DSC
not functional when having multiple FE clk to be enabled.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Fix incomplete copyright notice in DC code.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When DML 2 was introduced, it changed part of the generic sequence of
DC, which caused issues on previous DCNs with DMUB support. This commit
ensures the new sequence only works for new DCNs from 3.5 and above.
Changes since V1:
- Harry: Use the attribute using_dml2 instead of check the DCN version.
Cc: Vitaly Prosyak <vprosyak@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some ASICs keep backlight powered on after dpms off
command has been issued.
[How]
The check for no edp power sequencing was never going to pass.
The value is never changed from what it is set by design.
Cc: stable@vger.kernel.org # 6.1+
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2765
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When DML2 was introduced, it targeted only new DCN versions. For
controlling which ASIC should use this new version of DML, it was
introduced the using_dml2 attribute. To avoid ambiguities, this commit
explicitly sets using_dml2 to false in all ASICs that do not support
DML2.
Cc: Vitaly Prosyak <vprosyak@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During system boot in second screen only mode on a seamless boot system,
there is a chance that the pipe's det size might not be reset.
[How]
Reset the det size while resetting the pipe during seamless boot.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmU1ngkeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGrsIH/0k/+gdBBYFFdEym
foRhKir9WV3ZX4oIozJjA1f7T+qVYclKs6kaYm3gNepRBb6AoG8pdgv4MMAqhYsf
QMe2XHi0MrO/qKBgfNfivxEa9jq+0QK5uvTbqCRqCAB8LfwVyDqapCmg3EuiZcPW
UbMITmnwLIfXgPxvp9rabmCsTqO6FLbf0GDOVIkNSAIDBXMpcO1iffjrWUbhRa7n
oIoiJmWJLcXLxPWDsRKbpJwzw2cIG08YhfQYAiQnC3YaeRm1FKLDIICRBsmfYzja
rWv9r4dn4TDfV4/AnjggQnsZvz2yPCxNaFSQIT88nIeiLvyuUTJ9j8aidsSfMZQf
xZAbzbA=
=NoQv
-----END PGP SIGNATURE-----
BackMerge tag 'v6.6-rc7' into drm-next
This is needed to add the msm pr which is based on a higher base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit is the last part of the fix that reduces the stack size in
the DML2 code.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Chaitanya Dhere <chaitanya.dhere@amd.com>
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When compiling with allmodconfig, gcc highlights the following error:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c: In function 'dml_core_mode_support':
drivers/gpu/drm/amd/amdgpu/../display/dc/dml2/display_mode_core.c:8229:1: error: the frame size of 2736 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
8229 | } // dml_core_mode_support
| ^
cc1: all warnings being treated as errors
This commit mitigates part of this problem by extracting the prefetch
code to its own function. After applying this commit, the stack size
reduces from 2736 to 2464, however, the stack size issue becomes part of
the new function.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Chaitanya Dhere <chaitanya.dhere@amd.com>
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
display_mode_code.c is unconditionally built with
-Wframe-larger-than=2048, which causes warnings even when
CONFIG_FRAME_WARN has been set to 0, which should show no warnings.
Use the existing $(frame_warn_flag) variable, which handles this
situation. This is basically commit 25f178bbd0 ("drm/amd/display:
Respect CONFIG_FRAME_WARN=0 in dml Makefile") but for DML2.
Fixes: 7966f319c6 ("drm/amd/display: Introduce DML2")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
./drivers/gpu/drm/amd/display/dc/dml2/display_mode_core.c:4802:84-89: WARNING: conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6901
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
./drivers/gpu/drm/amd/display/dc/hwss/dce110/dce110_hwseq.c: dce110_hwseq.h is included more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6897
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn35/dcn35_fpu.c:261 dcn35_update_bw_bounding_box_fpu() warn: inconsistent indenting
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are a few spelling mistakes and an minor grammatical issue in
some dml_print messages. Fix these.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many of the register macros defined ind dcn32_resource.h have
extra brackets. This is not conforming to the style of those
defined in other DC header files.
[How]
Remove these brackets in dcn32_resource.h
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
A critial part of "drm/amd/display: Fix windowed MPO video with ODM
combine for DCN32" is lost during promotion to upstream. This patch
addes the code back to dc.c.
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 554340133e.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c6d3c7b630.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 8a307777c3.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 58c3b3341c.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 5b89d2ccc8.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit b79a00a4d4.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 77a66faacc.
[WHY & HOW]
The writeback series cause a regression in thunderbolt display.
Signed-off-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As dc_set_power_state() no longer allocates memory, it's not necessary
to have return types and check return code as it can't fail anymore.
Change it back to `void`.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If there is memory pressure at suspend time then dynamically
allocating a large structure as part of DC suspend code will
fail.
Instead re-use the same structures and clear all members except
those that should be maintained.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2362
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDPs fail to light up with seamless boot enabled
[How]
When seamless boot is enabled don't configure dpms_off
in disable_vbios_mode_if_required.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Refactor DPG test pattern logic for ODM cases
- Refactor HWSS into component folder
- Revert "drm/amd/display: Add a check for idle power optimization"
- Revert "drm/amd/display: remove duplicated edp relink to fastboot
- Update cursor limits based on SW cursor fallback limits
- Update stream mask
- Update pmfw_driver_if new structure
- Modify SMU message logs
- Don't set dpms_off for seamless boot
Known issue:
DWB (Writeback functionality) is broken.
Fix will be available in DC 3.2.256
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Enabling DPG causes HUBP to stay in blank constantly. If DPG is enabled
while an MCLK switch is taking place with SubVP, it will cause the MCLK
to never complete. This is because SubVP MCLK switch relies a HUBP
VLine interrupt, which will never occur when HUBP is constantly in
blank.
[How]
Disable SubVP when test pattern is enabled.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current DPG test pattern logic does not account for ODM configuration
changes after test pattern has already been programmed. For example, if
ODM2:1 is enabled after test pattern is already being output, the second
pipe is not programmed to output test pattern, causing half the screen
to be black.
[How]
Move DPG test pattern parameter calculations into separate function.
Whenever ODM pipe configuration changes, re-calculate DPG test pattern
parameters and program DPG if test pattern is currently enabled.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
eDPs fail to light up with seamless boot enabled
[How]
When seamless boot is enabled don't configure dpms_off
in disable_vbios_mode_if_required.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revert commit 434cf7af49 ("drm/amd/display: Add a check for idle power optimization")
Because it cause Freesync and S4 regression
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These functions can be called from high IRQ levels and the OS will hang
if it tries to use a usleep_highres or a msleep.
[How]
Replace the fsleep with a udelay.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
For determining the cursor size limit, use the same checks that
are used for determining SW cursor fallback instead of only
using SubVP
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need to use real clock table
[How]
Update the clock table
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Whenever stream changes because of new
pipe arrangements such as ODM. The new
stream mask is not reflected in DMCUB.
The mismatch in stream mask is blocking ips
entry in some scenarios.
[How]
Whenever stream arrangement changes,
update stream mask and notify DMCUB.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revert commit 984abb5384 ("drm/amd/display: remove duplicated edp relink to fastboot")
Because it cause 4k EDP not light up on boot
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fine tune the Vmin clock value
Reviewed-by: Robin Chen <robin.chen@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
pmfw header file updated, need align with data structure.
[How]
Update the data structure.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
It's important to make sure SMU messages
are logged by default to improve debugging for
power optimization use cases.
[how]
Change logs to warnings when SMU message
returns non-success id.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[what]
does_configuration_meet_sw_policies check was not done in the
validate_only portion of dml2, so some unsupported modes were passing bw
validation, only to fail the same check later in validate_and_build. now
we add the check to validate_only.
Also add line in dcn35_resource to ensure that value set for
enable_windowed_mpo_odm gets passed to dml.
[why]
Immediate black screen during video playback at 4k144hz. The debugger
showed that we were failing validation in dml on every updateplanes().
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update DML2 with replay vblank logic found in DML1.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain cases during a transition to ODM that might cause
corruption on the display. This occurs when we choose certain pipes in a
particular state.
[How]
We now will store the pipe indexes of the any pipes that might be
problematic to switch to during an ODM transition, and only use them as
a last resort.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Saaem Rizvi <syedsaaem.rizvi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc->dml2_options.use_native_pstate_optimization flag will make driver
use dcn32 legacy_svp_drr related tuning. Set this to false fixed the
stutter underflow issue also based on HW suggest disable ODM by default
and let DML choose it.
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Surface height/width for Chroma has another variable that it should be
intialized to, chroma_size. Fixing this will help pass DML2.0 validation
for YCbCr420 tests, DCHB006.109,129, DCHB014.011,012.
[how]
Assign SurfaceHeight/WidthC to chroma_size.height/width
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DML2 did not carry over DML1 logic that splits pipe for stero timings. Pipe
splitting is needed in this case to pass stereo tests.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Regression from DML1.0 where we use differen DET buffer sizes for each
pipe. From the spec, we need to use DET buffer size of 384 kb for each
pipe
[how]
Ensure to use 384 kb DET buffer sizes for each available pipe.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There are cases where more than 1 stream can be mapped to the same
surface. DML2.0 does not seem to handle these cases.
[how]
Make sure to account for the stream id when deriving the plane id. By
doing this, each plane id will be unique based on the stream id.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add z8 watermarks to struct for later ASIC use.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable DML2 for DCN35.
Changes since V1:
- Remove hard coded values
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC is transitioning from DML to DML2, and this commit introduces all the
required changes for some of the already available ASICs and adds the
required code infra to support new ASICs under DML2. DML2 is also a
generated code that provides better mode verification and programming
models for software/hardware, and it enables a better way to create
validation tools. This version is more like a middle step to the
complete transition to the DML2 version.
Changes since V1:
- Alex: Fix typos
Changes since V2:
- Update DC includes
Changes since V3:
- Fix 32 bit compilation issues on x86
Changes since V4:
- Avoid compilation of DML2 on some not supported 32-bit architecture
- Update commit message
Co-developed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Co-developed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For some reason, the dml code is not guarded under CONFIG_DRM_AMD_DC_FP
in the Makefile. This commit moves the dml code under the DC_FP guard.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bw_fixed does not need any FPU operation, and it is used on DCE and DCN.
For this reason, this commit moves bw_fixed to the basic folder outside
DML.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The custom_float file does not have any FPU operation, so it should be
inside DML. This commit moves the file to the basic folder.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dce_calcs does not have FPU operations, and it is required for DCE and
DCN. Remove this file from the DML folder and add it to the basic folder
visible for DCE and DCN.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn20_validate_bandwidth_fp() is invoked while FPU access has been
enabled. FPU access requires disabling preemption even on PREEMPT_RT.
It is not possible to allocate memory with disabled preemption even with
GFP_ATOMIC on PREEMPT_RT.
Move the memory allocation before FPU access is enabled.
To preserve previous "clean" state of "pipes" add a memset() before the
second invocation of dcn20_validate_bandwidth_internal() where the
variable is used.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn21_validate_bandwidth_fp() is invoked while FPU access has been
enabled. FPU access requires disabling preemption even on PREEMPT_RT.
It is not possible to allocate memory with disabled preemption even with
GFP_ATOMIC on PREEMPT_RT.
Move the memory allocation before FPU access is enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217928
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The edge-case DISPCLK WDIVIDER changes call stream_enc functions.
But with MPC pipes, downstream pipes have null stream_enc and will
cause crash.
[How]
Only call stream_enc functions for pipes that are OTG master.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC v3.2.254
* Stability fixes through null pointer checks, blackscreen fixes on
certain configurations
* Improvements for various functionality like Idle optimization, ILR, DSC, IPS
* Fixes for ILR functionality
* Trivial code cleanups
===================================================================
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Clip size increase will increase viewport, which could cause us to
switch to MPC combine.
If we skip full update, we are not able to change to MPC combine in
fast update. This will cause corruption showing on the video plane.
[how]
treat clip size increase of a surface larger than 5k as a full update.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Driver needs to be compatible with PM FW that doesn't support IPS
[how]
Toggle internal control flag
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current ILR toggle is on/off as a part of panel
config for new function, which breaks original
ILR logic
[How]
Refactor ILR and take panel config into account
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Sherry Wang <yao.wang1@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
enable_accelerated_mode function is fully to check
whether fastboot support or not.
It is no longer to disable_vbios_mode_if_required.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The edge-case DISPCLK WDIVIDER changes call stream_enc functions.
But with MPC pipes, downstream pipes have null stream_enc and will
cause crash.
[How]
Only call stream_enc functions for pipes that are OTG master.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
need to enable dsc_clk regardless dsc_pg
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[what and why]
Check whether dpp resource pointer is null in advance and return early
if so.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Martin Leung <martin.leung@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
drm_writeback requires to capture exact one frame in each writeback
call.
[HOW]
frame_capture is disabled after each writeback is completed.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Add a function to enable and disable DWB's frame captures.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Counter j was not updated to present the num of writeback_info when
writeback pipes are removed.
[HOW]
update j (num of writeback info) under the correct condition.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
hw_points_num is 0 before ogam LUT is programmed; however, function
"dwb3_program_ogam_pwl" assumes hw_points_num is always greater than 0,
i.e. substracting it by 1 as an array index.
[HOW]
Check hw_points_num is not equal to 0 before using it.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
wb_enabled field is set to false before it is used, and the following
code will never be executed.
[HOW]
Setting wb_enable to false after all removal work is completed.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
The enable and disable writeback calls need to be included in the
coressponding functions in dc_stream.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:3928: warning: Function parameter or member 'srf_updates' not described in 'could_mpcc_tree_change_for_active_pipes'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
Prepare a virtual connector for writeback.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
These DPCD addresses are either declared in other header files
where it makes more sense or simply not used by any DC code.
Remove them to reduce redundancies and potential confusion.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC code is reused by other OSes and so Linux return codes don't
make sense. Change dc_set_power_state() to boolean and add a wrapper
dm_set_power_state() to return a Linux error code for the memory
allocation failure.
Suggested-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the suspend process dc_set_power_state() will use kzalloc
to allocate memory, but this potentially fails with memory pressure.
If it fails, the suspend should be aborted.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2362
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: Harry.Wentland@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc->caps.color.mpc.gamut_remap says there is a post-blending color block
for gamut remap matrix for DCN3 HW family and newer versions. However,
those drivers still follow DCN10 programming that remap stream
gamut_remap_matrix to DPP (pre-blending).
To enable pre-blending and post-blending gamut_remap matrix supports at
the same time, set stream gamut_remap to MPC and plane gamut_remap to
DPP for DCN families that support both.
It was tested using IGT KMS color tests for DRM CRTC CTM property and it
preserves test results.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
After repopulating pipes for a split / merge, we want to find the
lowest vlevel that supports the desired mpc combine level.
Reviewed-by: Nevenko Stupar <nevenko.stupar@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Change to new interface for notifying OS of cursor support changes
Reviewed-by: Gang Chu <gang.chu@amd.com>
Reviewed-by: Jaina Han <jaina.han@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Hong-lu Cheng <hong-lu.cheng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Allow dc report maximum display clock possible at vmin
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Max Tseng <max.tseng@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along the following:
- Fix incorrect odm change detection logic
- Add primary pipe check when building slice table for dcn3x
- Add get primary dpp pipe resource interface
- Add missing function pointer for DCN321 resource
- Rename DisableMinDispClkODM in dc_config
- Break after finding supported vlevel for repopulate
- Update OPP counter from new interface
- Augment display clock in dc_cap structure
- Improve code style on bios_parser2
- Skip audio config for virtual signal
- Block MPO if it prevents pstate support
- Fix DP2.0 timing sync
- Improve x86 and dmub ips handshake
- Remove guaranteed viewports limitation for odm
- Add new windowed mpo odm minimal transition sequence
- Reset stream slice count for new ODM policy
- Determine fast update only before commit minimal transition state
- Remove unused mmhub_reg_offsets
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current ODM change detection only compares first two ODM slices.
If there are 4 ODM slices and the change is within the last two slices, the
logic fails to detect ODM change and cause us to skip ODM programming
unexpectedly.
[how]
Add a is ODM topology changed resource interface to check any ODM
topology changes with a more generic method.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hamza Mahfooz
Johnson Chen
Aric Cyr
Alvin Lee
Muhammad Ahmed
Samson Tam
Peyton Lee
Charlene Liu
Sung Joon Kim
Allen
Fangzhi Zuo
Michael Strauss
Aurabindo Pillai
Taimur Hassan
Ran Shi
Joshua Aberback
Colin Ian King
Mario Limonciello
Alex Deucher
Rodrigo Siqueira
Roman Li
Alex Hung
Harry Wentland
Wenjing Liu
Dennis Chan
Dillon Varone
Yihan Zhu
Nicholas Susanto
Relja Vojvodic
Nicholas Kazlauskas
Chris Park
George Shen
Ilya Bakoulin
Krunoslav Kovac
Lewis Huang
Daniel Miess
Dmytro Laktyushkin
RutingZhang
Parandhaman K
Zhongwei
Gabe Teeger
Meenakshikumar Somasundaram
Wayne Lin
Camille Cho
Max Tseng
Bhuvana Chandra Pinninti
Ian Chen
Duncan Ma
Mounika Adhuri
Paul Hsieh
José Pekkarinen
Bragatheswaran Manickavel
Chaitanya Dhere
Ovidiu Bunea
ChunTao Tso
JinZe.Xu
Nathan Chancellor
Iswara Nagulendran
Swapnil Patel
Stylon Wang
Agustin Gutierrez
Hugo Hu
Dave Airlie
Yang Li
Bob Zhou
Saaem Rizvi
Qingqing Zhuo
Sebastian Andrzej Siewior
Sung Joon Kim
Sherry Wang
Chiawen Huang
Srinivasan Shanmugam
Melissa Wen
Hong-lu Cheng