linux/drivers
Giuseppe CAVALLARO a59a4d1921 phy: add the EEE support and the way to access to the MMD registers.
This patch adds the support for the Energy-Efficient Ethernet (EEE)
to the Physical Abstraction Layer.
To support the EEE we have to access to the MMD registers 3.20 and
7.60/61. So two new functions have been added to read/write the MMD
registers (clause 45).

An Ethernet driver (I tested the stmmac) can invoke the phy_init_eee to properly
check if the EEE is supported by the PHYs and it can also set the clock
stop enable bit in the 3.0 register.
The phy_get_eee_err can be used for reporting the number of time where
the PHY failed to complete its normal wake sequence.

In the end, this patch also adds the EEE ethtool support implementing:
 o phy_ethtool_set_eee
 o phy_ethtool_get_eee

v1: initial patch
v2: fixed some errors especially on naming convention
v3: renamed again the mmd read/write functions thank to Ben's feedback
v4: moved file to phy.c and added the ethtool support.
v5: fixed phy_adv_to_eee, phy_eee_to_supported, phy_eee_to_adv return
    values according to ethtool API (thanks to Ben's feedback).
    Renamed some macros to avoid too long names.
v6: fixed kernel-doc comments to be properly parsed.
    Fixed the phy_init_eee function: we need to check which link mode
    was autonegotiated and then the corresponding bits in 7.60 and 7.61
    registers.
v7: reviewed the way to get the negotiated settings.
v8: fixed a problem in the phy_init_eee return value erroneously added
    when included the phy_read_status call.
v9: do not remove the MDIO_AN_EEE_ADV_100TX and MDIO_AN_EEE_ADV_1000T
    and fixed the eee_{cap,lp,adv} declaration as "int" instead of u16.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-01 03:34:50 -07:00
..
accessibility
acpi
amba
ata
atm
auxdisplay
base
bcma
block
bluetooth Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless 2012-06-29 12:07:37 -04:00
cdrom
char
clk
clocksource
connector netlink: add netlink_kernel_cfg parameter to netlink_kernel_create 2012-06-29 16:46:02 -07:00
cpufreq
cpuidle
crypto
dca
devfreq
dio
dma
edac
eisa
extcon
firewire
firmware
gpio
gpu
hid
hsi
hv
hwmon
hwspinlock
i2c
ide
idle
ieee802154
iio
infiniband netlink: add netlink_kernel_cfg parameter to netlink_kernel_create 2012-06-29 16:46:02 -07:00
input
iommu
isdn
leds
lguest
macintosh
md
media
memory
memstick
message
mfd
misc
mmc
mtd
net phy: add the EEE support and the way to access to the MMD registers. 2012-07-01 03:34:50 -07:00
nfc
nubus
of
oprofile
parisc
parport
pci
pcmcia
pinctrl
platform
pnp
power
pps
ps3
ptp
rapidio
regulator
remoteproc
rpmsg
rtc
s390
sbus
scsi netlink: add netlink_kernel_cfg parameter to netlink_kernel_create 2012-06-29 16:46:02 -07:00
sfi
sh
sn
spi
ssb
staging netlink: add netlink_kernel_cfg parameter to netlink_kernel_create 2012-06-29 16:46:02 -07:00
target
tc
thermal
tty
uio
usb
uwb
vhost
video
virt
virtio
vlynq
vme
w1
watchdog
xen
zorro
Kconfig
Makefile