Add RmNet support for LARA-R6 01B.
The new LARA-R6 product variant identified by the "01B" string can be
configured (by AT interface) in three different USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1311) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1312) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1313) with 4 serial
interface and 1 CDC-ECM virtual network interface
The first 4 interfaces of all the 3 configurations (default, RmNet, ECM)
are the same.
In RmNet mode LARA-R6 01B exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20230626125336.3127-1-davide.tronchin.94@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move declarations into include/net/gso.h and code into net/core/gso.c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stanislav Fomichev <sdf@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230608191738.3947077-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This module has for a long time not been limited to iPhone <= 3GS.
Update description to match the actual state of the driver.
Remove dead link from 2010, instead reference an existing userspace
iOS device pairing implementation as part of libimobiledevice.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent iOS releases support CDC NCM encapsulation on RX. This mode is
the default on macOS and Windows. In this mode, an iOS device may include
one or more Ethernet frames inside a single URB.
Freshly booted iOS devices start in legacy mode, but are put into
NCM mode by the official Apple driver. When reconnecting such a device
from a macOS/Windows machine to a Linux host, the device stays in
NCM mode, making it unusable with the legacy ipheth driver code.
To correctly support such a device, the driver has to either support
the NCM mode too, or put the device back into legacy mode.
To match the behaviour of the macOS/Windows driver, and since there
is no documented control command to revert to legacy mode, implement
NCM support. The device is attempted to be put into NCM mode by default,
and falls back to legacy mode if the attempt fails.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The behaviour of the official iOS tethering driver on macOS is to not
transmit any trailing padding at the end of URBs. This is applicable
to both NCM and legacy modes, including older devices.
Adapt the driver to not include trailing padding in TX URBs, matching
the behaviour of the official macOS driver.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cleanup precedure in ipheth_probe will attempt to free a
NULL pointer in dev->ctrl_buf if the memory allocation for
this buffer is not successful. While kfree ignores NULL pointers,
and the existing code is safe, it is a better design to rearrange
the goto labels and avoid this.
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move setting r8153b_rx_agg_chg_indicate() for 2.5G devices. The
r8153b_rx_agg_chg_indicate() has to be called after enabling tx/rx.
Otherwise, the coalescing settings are useless.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the poor throughput for 2.5G devices, when changing the speed from
auto mode to force mode. This patch is used to notify the MAC when the
mode is changed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The feature of flow control becomes abnormal, if the device sends a
pause frame and the tx/rx is disabled before sending a release frame. It
causes the lost of packets.
Set PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY to zeros before disabling the
tx/rx. And, toggle FC_PATCH_TASK before enabling tx/rx to reset the flow
control patch and timer. Then, the hardware could clear the state and
the flow control becomes normal after enabling tx/rx.
Besides, remove inline for fc_pause_on_auto() and fc_pause_off_auto().
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory is a little tight on my system, it's pretty easy to see
warnings that look like this.
ksoftirqd/0: page allocation failure: order:3, mode:0x40a20(GFP_ATOMIC|__GFP_COMP), nodemask=(null),cpuset=/,mems_allowed=0
...
Call trace:
dump_backtrace+0x0/0x1e8
show_stack+0x20/0x2c
dump_stack_lvl+0x60/0x78
dump_stack+0x18/0x38
warn_alloc+0x104/0x174
__alloc_pages+0x588/0x67c
alloc_rx_agg+0xa0/0x190 [r8152 ...]
r8152_poll+0x270/0x760 [r8152 ...]
__napi_poll+0x44/0x1ec
net_rx_action+0x100/0x300
__do_softirq+0xec/0x38c
run_ksoftirqd+0x38/0xec
smpboot_thread_fn+0xb8/0x248
kthread+0x134/0x154
ret_from_fork+0x10/0x20
On a fragmented system it's normal that order 3 allocations will
sometimes fail, especially atomic ones. The driver handles these
failures fine and the WARN just creates spam in the logs for this
case. The __GFP_NOWARN flag is exactly for this situation, so add it
to the allocation.
NOTE: my testing is on a 5.15 system, but there should be no reason
that this would be fundamentally different on a mainline kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20230406171411.1.I84dbef45786af440fd269b71e9436a96a8e7a152@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
"modprobe asix ; rmmod asix ; modprobe asix" fails with:
sysfs: cannot create duplicate filename \
'/devices/virtual/mdio_bus/usb-003:004'
Issue was originally reported by Anton Lundin on 2022-06-22 (link below).
Chrome OS team hit the same issue in Feb, 2023 when trying to find
work arounds for other issues with AX88172 devices.
The use of devm_mdiobus_register() with usbnet devices results in the
MDIO data being associated with the USB device. When the asix driver
is unloaded, the USB device continues to exist and the corresponding
"mdiobus_unregister()" is NOT called until the USB device is unplugged
or unauthorized. So the next "modprobe asix" will fail because the MDIO
phy sysfs attributes still exist.
The 'easy' (from a design PoV) fix is to use the non-devm variants of
mdiobus_* functions and explicitly manage this use in the asix_bind
and asix_unbind function calls. I've not explored trying to fix usbnet
initialization so devm_* stuff will work.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/netdev/20220623063649.GD23685@pengutronix.de/T/
Tested-by: Eizan Miyamoto <eizan@chromium.org>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Link: https://lore.kernel.org/r/20230321170539.732147-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
clang with W=1 reports
drivers/net/usb/plusb.c:65:1: error:
unused function 'pl_clear_QuickLink_features' [-Werror,-Wunused-function]
pl_clear_QuickLink_features(struct usbnet *dev, int val)
^
This static function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet length retrieved from descriptor may be larger than
the actual socket buffer length. In such case the cloned
skb passed up the network stack will leak kernel memory contents.
Additionally prevent integer underflow when size is less than
ETH_FCS_LEN.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet length retrieved from descriptor may be larger than
the actual socket buffer length. In such case the cloned
skb passed up the network stack will leak kernel memory contents.
Fixes: 2f7ca802bd ("net: Add SMSC LAN9500 USB2.0 10/100 ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230316101954.75836-1-szymon.heidrich@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packet length check needs to be located after size and align_count
calculation to prevent kernel panic in skb_pull() in case
rx_cmd_a & RX_CMD_A_RED evaluates to true.
Fixes: d8b2283189 ("net: usb: smsc75xx: Limit packet length to skb->len")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230316110540.77531-1-szymon.heidrich@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Packet length retrieved from skb data may be larger than
the actual socket buffer length (up to 9026 bytes). In such
case the cloned skb passed up the network stack will leak
kernel memory contents.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FE990
0x1081 composition in order to avoid bind error.
Signed-off-by: Enrico Sau <enrico.sau@gmail.com>
Link: https://lore.kernel.org/r/20230306115933.198259-1-enrico.sau@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microchip.c).
Fix the error reported by Enguerrand de Ribaucourt in December 2022,
"Some operations during the cable switch workaround modify the register
LAN88XX_INT_MASK of the PHY. However, this register is specific to the
LAN8835 PHY. For instance, if a DP8322I PHY is connected to the LAN7801,
that register (0x19), corresponds to the LED and MAC address
configuration, resulting in unapropriate behavior."
I did not test with the DP8322I PHY, but I tested with an EVB-LAN7800
with the internal PHY.
Fixes: 14437e3fa2 ("lan78xx: workaround of forced 100 Full/Half duplex mode error")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230301154307.30438-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot reported that act_len in kalmia_send_init_packet() is
uninitialized when passing it to the first usb_bulk_msg error path. Jiri
Pirko noted that it's pointless to pass it in the error path, and that
the value that would be printed in the second error path would be the
value of act_len from the first call to usb_bulk_msg.[1]
With this in mind, let's just not pass act_len to the usb_bulk_msg error
paths.
1: https://lore.kernel.org/lkml/Y9pY61y1nwTuzMOa@nanopsycho/
Fixes: d40261236e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Reported-and-tested-by: syzbot+cd80c5ef5121bfe85b55@syzkaller.appspotmail.com
Signed-off-by: Miko Larsson <mikoxyzzz@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the control transfer by moving calling rtl8152_get_version() in
rtl8152_probe(). This could prevent from calling rtl8152_get_version()
for unnecessary situations. For example, after setting config #2 for the
device, there are two interfaces and rtl8152_probe() may be called
twice. However, we don't need to call rtl8152_get_version() for this
situation.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit ec51fbd1b8 ("r8152: add USB device driver for
config selection"), the code about changing USB configuration
in rtl_vendor_mode() wouldn't be run anymore. Therefore, the
function could be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The rtl8152_cfgselector_probe() should set the USB configuration to the
vendor mode only for the devices which the driver (r8152) supports.
Otherwise, no driver would be used for such devices.
Fixes: ec51fbd1b8 ("r8152: add USB device driver for config selection")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet len computed as difference of length word extracted from
skb data and four may result in a negative value. In such case
processing of the buffer should be interrupted rather than
setting sr_skb->len to an unexpectedly large value (due to cast
from signed to unsigned integer) and passing sr_skb to
usbnet_skb_return.
Fixes: e9da0b56fe ("sr9700: sanity check for packet length")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230114182326.30479-1-szymon.heidrich@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Microsoft Devkit 2023 is a an ARM64 based machine featuring a
Realtek 8153 USB3.0-to-GBit Ethernet adapter. As in their other
machines, Microsoft uses a custom USB device ID.
Add the respective ID values to the driver. This makes Ethernet work on
the MS Devkit device. The chip has been visually confirmed to be a
RTL8153.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20230111133228.190801-1-andre.przywara@arm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The r8152 driver does not need this anymore.
Dropping blacklist entries adds optional support for these
devices in ECM mode.
The 8153 devices are handled by the r8153_ecm driver when
in ECM mode, and must still be blacklisted here.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subclassing the generic USB device driver to override the
default configuration selection regardless of matching interface
drivers.
The r815x family devices expose a vendor specific function which
the r8152 interface driver wants to handle. This is the preferred
device mode. Additionally one or more USB class functions are
usually supported for hosts lacking a vendor specific driver. The
choice is USB configuration based, with one alternate function per
configuration.
Example device with both NCM and ECM alternate cfgs:
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=5000 MxCh= 0
D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 3
P: Vendor=0bda ProdID=8156 Rev=31.00
S: Manufacturer=Realtek
S: Product=USB 10/100/1G/2.5G LAN
S: SerialNumber=001000001
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=256mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=00 Driver=r8152
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=128ms
C: #Ifs= 2 Cfg#= 2 Atr=a0 MxPwr=256mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0d Prot=00 Driver=
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=01 Driver=
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
C: #Ifs= 2 Cfg#= 3 Atr=a0 MxPwr=256mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=
I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=
E: Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
A problem with this is that Linux will prefer class functions over
vendor specific functions. Using the above example, Linux defaults
to cfg #2, running the device in a sub-optimal NCM mode.
Previously we've attempted to work around the problem by
blacklisting the devices in the ECM class driver "cdc_ether", and
matching on the ECM class function in the vendor specific interface
driver. The latter has been used to switch back to the vendor
specific configuration when the driver is probed for a class
function.
This workaround has several issues;
- class driver blacklists is additional maintanence cruft in an
unrelated driver
- class driver blacklists prevents users from optionally running
the devices in class mode
- each device needs double match entries in the vendor driver
- the initial probing as a class function slows down device
discovery
Now these issues have become even worse with the introduction of
firmware supporting both NCM and ECM, where NCM ends up as the
default mode in Linux. To use the same workaround, we now have
to blacklist the devices in to two different class drivers and
add yet another match entry to the vendor specific driver.
This patch implements an alternative workaround strategy -
independent of the interface drivers. It avoids adding a
blacklist to the cdc_ncm driver and will let us remove the
existing blacklist from the cdc_ether driver.
As an additional bonus, removing the blacklists allow users to
select one of the other device modes if wanted.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current source pushes skb into dev-done queue by calling
skb_dequeue_tail() and then pop it by skb_dequeue() to branch to
rx_cleanup state for freeing urb/skb in usbnet_bh(). It takes extra CPU
load, 2.21% (skb_queue_tail) as follows,
- 11.58% 0.26% swapper [k] usbnet_bh
- 11.32% usbnet_bh
- 6.43% skb_dequeue
6.34% _raw_spin_unlock_irqrestore
- 2.21% skb_queue_tail
2.19% _raw_spin_unlock_irqrestore
- 1.68% consume_skb
- 0.97% kfree_skbmem
0.80% kmem_cache_free
0.53% skb_release_data
To reduce the extra CPU load use return values to call helper function
usb_free_skb() to free the resources instead of calling skb_queue_tail()
and skb_dequeue() for push and pop respectively.
- 7.87% 0.25% swapper [k] usbnet_bh
- 7.62% usbnet_bh
- 4.81% skb_dequeue
4.74% _raw_spin_unlock_irqrestore
- 1.75% consume_skb
- 0.98% kfree_skbmem
0.78% kmem_cache_free
0.58% skb_release_data
0.53% smsc95xx_rx_fixup
Signed-off-by: Leesoo Ahn <lsahn@ooseel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This modem has 7 interfaces, 5 of them are serial interfaces and are
driven by cdc_acm, while 2 of them are wwan interfaces and are driven
by cdc_ether:
If 0: Abstract (modem)
If 1: Abstract (modem)
If 2: Abstract (modem)
If 3: Abstract (modem)
If 4: Abstract (modem)
If 5: Ethernet Networking
If 6: Ethernet Networking
Without this change, the 2 network interfaces will be named to usb0
and usb1, our QA think the names are confusing and filed a bug on it.
After applying this change, the name will be wwan0 and wwan1, and
they could work well with modem manager.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230105034249.10433-1-hui.wang@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current release - regressions:
- bpf: fix nullness propagation for reg to reg comparisons,
avoid null-deref
- inet: control sockets should not use current thread task_frag
- bpf: always use maximal size for copy_array()
- eth: bnxt_en: don't link netdev to a devlink port for VFs
Current release - new code bugs:
- rxrpc: fix a couple of potential use-after-frees
- netfilter: conntrack: fix IPv6 exthdr error check
- wifi: iwlwifi: fw: skip PPAG for JF, avoid FW crashes
- eth: dsa: qca8k: various fixes for the in-band register access
- eth: nfp: fix schedule in atomic context when sync mc address
- eth: renesas: rswitch: fix getting mac address from device tree
- mobile: ipa: use proper endpoint mask for suspend
Previous releases - regressions:
- tcp: add TIME_WAIT sockets in bhash2, fix regression caught
by Jiri / python tests
- net: tc: don't intepret cls results when asked to drop, fix
oob-access
- vrf: determine the dst using the original ifindex for multicast
- eth: bnxt_en:
- fix XDP RX path if BPF adjusted packet length
- fix HDS (header placement) and jumbo thresholds for RX packets
- eth: ice: xsk: do not use xdp_return_frame() on tx_buf->raw_buf,
avoid memory corruptions
Previous releases - always broken:
- ulp: prevent ULP without clone op from entering the LISTEN status
- veth: fix race with AF_XDP exposing old or uninitialized descriptors
- bpf:
- pull before calling skb_postpull_rcsum() (fix checksum support
and avoid a WARN())
- fix panic due to wrong pageattr of im->image (when livepatch
and kretfunc coexist)
- keep a reference to the mm, in case the task is dead
- mptcp: fix deadlock in fastopen error path
- netfilter:
- nf_tables: perform type checking for existing sets
- nf_tables: honor set timeout and garbage collection updates
- ipset: fix hash:net,port,net hang with /0 subnet
- ipset: avoid hung task warning when adding/deleting entries
- selftests: net:
- fix cmsg_so_mark.sh test hang on non-x86 systems
- fix the arp_ndisc_evict_nocarrier test for IPv6
- usb: rndis_host: secure rndis_query check against int overflow
- eth: r8169: fix dmar pte write access during suspend/resume with WOL
- eth: lan966x: fix configuration of the PCS
- eth: sparx5: fix reading of the MAC address
- eth: qed: allow sleep in qed_mcp_trace_dump()
- eth: hns3:
- fix interrupts re-initialization after VF FLR
- fix handling of promisc when MAC addr table gets full
- refine the handling for VF heartbeat
- eth: mlx5:
- properly handle ingress QinQ-tagged packets on VST
- fix io_eq_size and event_eq_size params validation on big endian
- fix RoCE setting at HCA level if not supported at all
- don't turn CQE compression on by default for IPoIB
- eth: ena:
- fix toeplitz initial hash key value
- account for the number of XDP-processed bytes in interface stats
- fix rx_copybreak value update
Misc:
- ethtool: harden phy stat handling against buggy drivers
- docs: netdev: convert maintainer's doc from FAQ to a normal document
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=TlcN
-----END PGP SIGNATURE-----
Merge tag 'net-6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf, wifi, and netfilter.
Current release - regressions:
- bpf: fix nullness propagation for reg to reg comparisons, avoid
null-deref
- inet: control sockets should not use current thread task_frag
- bpf: always use maximal size for copy_array()
- eth: bnxt_en: don't link netdev to a devlink port for VFs
Current release - new code bugs:
- rxrpc: fix a couple of potential use-after-frees
- netfilter: conntrack: fix IPv6 exthdr error check
- wifi: iwlwifi: fw: skip PPAG for JF, avoid FW crashes
- eth: dsa: qca8k: various fixes for the in-band register access
- eth: nfp: fix schedule in atomic context when sync mc address
- eth: renesas: rswitch: fix getting mac address from device tree
- mobile: ipa: use proper endpoint mask for suspend
Previous releases - regressions:
- tcp: add TIME_WAIT sockets in bhash2, fix regression caught by
Jiri / python tests
- net: tc: don't intepret cls results when asked to drop, fix
oob-access
- vrf: determine the dst using the original ifindex for multicast
- eth: bnxt_en:
- fix XDP RX path if BPF adjusted packet length
- fix HDS (header placement) and jumbo thresholds for RX packets
- eth: ice: xsk: do not use xdp_return_frame() on tx_buf->raw_buf,
avoid memory corruptions
Previous releases - always broken:
- ulp: prevent ULP without clone op from entering the LISTEN status
- veth: fix race with AF_XDP exposing old or uninitialized
descriptors
- bpf:
- pull before calling skb_postpull_rcsum() (fix checksum support
and avoid a WARN())
- fix panic due to wrong pageattr of im->image (when livepatch and
kretfunc coexist)
- keep a reference to the mm, in case the task is dead
- mptcp: fix deadlock in fastopen error path
- netfilter:
- nf_tables: perform type checking for existing sets
- nf_tables: honor set timeout and garbage collection updates
- ipset: fix hash:net,port,net hang with /0 subnet
- ipset: avoid hung task warning when adding/deleting entries
- selftests: net:
- fix cmsg_so_mark.sh test hang on non-x86 systems
- fix the arp_ndisc_evict_nocarrier test for IPv6
- usb: rndis_host: secure rndis_query check against int overflow
- eth: r8169: fix dmar pte write access during suspend/resume with
WOL
- eth: lan966x: fix configuration of the PCS
- eth: sparx5: fix reading of the MAC address
- eth: qed: allow sleep in qed_mcp_trace_dump()
- eth: hns3:
- fix interrupts re-initialization after VF FLR
- fix handling of promisc when MAC addr table gets full
- refine the handling for VF heartbeat
- eth: mlx5:
- properly handle ingress QinQ-tagged packets on VST
- fix io_eq_size and event_eq_size params validation on big endian
- fix RoCE setting at HCA level if not supported at all
- don't turn CQE compression on by default for IPoIB
- eth: ena:
- fix toeplitz initial hash key value
- account for the number of XDP-processed bytes in interface stats
- fix rx_copybreak value update
Misc:
- ethtool: harden phy stat handling against buggy drivers
- docs: netdev: convert maintainer's doc from FAQ to a normal
document"
* tag 'net-6.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
caif: fix memory leak in cfctrl_linkup_request()
inet: control sockets should not use current thread task_frag
net/ulp: prevent ULP without clone op from entering the LISTEN status
qed: allow sleep in qed_mcp_trace_dump()
MAINTAINERS: Update maintainers for ptp_vmw driver
usb: rndis_host: Secure rndis_query check against int overflow
net: dpaa: Fix dtsec check for PCS availability
octeontx2-pf: Fix lmtst ID used in aura free
drivers/net/bonding/bond_3ad: return when there's no aggregator
netfilter: ipset: Rework long task execution when adding/deleting entries
netfilter: ipset: fix hash:net,port,net hang with /0 subnet
net: sparx5: Fix reading of the MAC address
vxlan: Fix memory leaks in error path
net: sched: htb: fix htb_classify() kernel-doc
net: sched: cbq: dont intepret cls results when asked to drop
net: sched: atm: dont intepret cls results when asked to drop
dt-bindings: net: marvell,orion-mdio: Fix examples
dt-bindings: net: sun8i-emac: Add phy-supply property
net: ipa: use proper endpoint mask for suspend
selftests: net: return non-zero for failures reported in arp_ndisc_evict_nocarrier
...
Variables off and len typed as uint32 in rndis_query function
are controlled by incoming RNDIS response message thus their
value may be manipulated. Setting off to a unexpectetly large
value will cause the sum with len and 8 to overflow and pass
the implemented validation step. Consequently the response
pointer will be referring to a location past the expected
buffer boundaries allowing information leakage e.g. via
RNDIS_OID_802_3_PERMANENT_ADDRESS OID.
Fixes: ddda086240 ("USB: rndis_host, various cleanups")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to several bugs caused by timers being re-armed after they are
shutdown and just before they are freed, a new state of timers was added
called "shutdown". After a timer is set to this state, then it can no
longer be re-armed.
The following script was run to find all the trivial locations where
del_timer() or del_timer_sync() is called in the same function that the
object holding the timer is freed. It also ignores any locations where
the timer->function is modified between the del_timer*() and the free(),
as that is not considered a "trivial" case.
This was created by using a coccinelle script and the following
commands:
$ cat timer.cocci
@@
expression ptr, slab;
identifier timer, rfield;
@@
(
- del_timer(&ptr->timer);
+ timer_shutdown(&ptr->timer);
|
- del_timer_sync(&ptr->timer);
+ timer_shutdown_sync(&ptr->timer);
)
... when strict
when != ptr->timer
(
kfree_rcu(ptr, rfield);
|
kmem_cache_free(slab, ptr);
|
kfree(ptr);
)
$ spatch timer.cocci . > /tmp/t.patch
$ patch -p1 < /tmp/t.patch
Link: https://lore.kernel.org/lkml/20221123201306.823305113@linutronix.de/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Pavel Machek <pavel@ucw.cz> [ LED ]
Acked-by: Kalle Valo <kvalo@kernel.org> [ wireless ]
Acked-by: Paolo Abeni <pabeni@redhat.com> [ networking ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add CDC-ECM support for LARA-L6.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In CDC-ECM mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: CDC-ECM interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Link: https://lore.kernel.org/r/20221124112811.3548-1-davide.tronchin.94@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ZLP for DisplayLink ethernet devices was enabled in 6.0:
266c0190ae ("net/cdc_ncm: Enable ZLP for DisplayLink ethernet devices").
The related driver_info should be the "same as cdc_ncm_info, but with
FLAG_SEND_ZLP". However, set_rx_mode that enables handling multicast
traffic was missing in the new cdc_ncm_zlp_info.
usbnet_cdc_update_filter rx mode was introduced in linux 5.9 with:
e10dcb1b6b ("net: cdc_ncm: hook into set_rx_mode to admit multicast
traffic")
Without this hook, multicast, and then IPv6 SLAAC, is broken.
Fixes: 266c0190ae ("net/cdc_ncm: Enable ZLP for DisplayLink ethernet devices")
Signed-off-by: Santiago Ruano Rincón <santiago.ruano-rincon@imt-atlantique.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RmNet support for LARA-L6.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
An external PHY needs settling time after power up or reset.
In the bind() function an mdio bus is registered. If at this point
the external PHY is still initialising, no valid PHY ID will be
read and on phy_find_first() the bind() function will fail.
If an external PHY is present, wait the maximum time specified
in 802.3 45.2.7.1.1.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221115114434.9991-2-alexandru.tachici@analog.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
strtobool() is the same as kstrtobool().
However, the latter is more used within the kernel.
In order to remove strtobool() and slightly simplify kstrtox.h, switch to
the other function name.
While at it, include the corresponding header file (<linux/kstrtox.h>).
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d4432a67b6f769cac0a9ec910ac725298b64e102.1667336095.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to
finally get this work done
- tty serial transmit cleanups in various drivers in preparation
for more cleanup and unification in future releases (that work
was not ready for this release.)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full
details in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY0BSdA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylucQCfaXIrYuh2AHcb6+G+Nqp1xD2BYaEAoIdLyOCA
a2yziLrDF6us2oav6j4x
=Wv+X
-----END PGP SIGNATURE-----
Merge tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of TTY and Serial driver updates for 6.1-rc1.
Lots of cleanups in here, no real new functionality this time around,
with the diffstat being that we removed more lines than we added!
Included in here are:
- termios unification cleanups from Al Viro, it's nice to finally get
this work done
- tty serial transmit cleanups in various drivers in preparation for
more cleanup and unification in future releases (that work was not
ready for this release)
- n_gsm fixes and updates
- ktermios cleanups and code reductions
- dt bindings json conversions and updates for new devices
- some serial driver updates for new devices
- lots of other tiny cleanups and janitorial stuff. Full details in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (102 commits)
serial: cpm_uart: Don't request IRQ too early for console port
tty: serial: do unlock on a common path in altera_jtaguart_console_putc()
tty: serial: unify TX space reads under altera_jtaguart_tx_space()
tty: serial: use FIELD_GET() in lqasc_tx_ready()
tty: serial: extend lqasc_tx_ready() to lqasc_console_putchar()
tty: serial: allow pxa.c to be COMPILE_TESTed
serial: stm32: Fix unused-variable warning
tty: serial: atmel: Add COMMON_CLK dependency to SERIAL_ATMEL
serial: 8250: Fix restoring termios speed after suspend
serial: Deassert Transmit Enable on probe in driver-specific way
serial: 8250_dma: Convert to use uart_xmit_advance()
serial: 8250_omap: Convert to use uart_xmit_advance()
MAINTAINERS: Solve warning regarding inexistent atmel-usart binding
serial: stm32: Deassert Transmit Enable on ->rs485_config()
serial: ar933x: Deassert Transmit Enable on ->rs485_config()
tty: serial: atmel: Use FIELD_PREP/FIELD_GET
tty: serial: atmel: Make the driver aware of the existence of GCLK
tty: serial: atmel: Only divide Clock Divisor if the IP is USART
tty: serial: atmel: Separate mode clearing between UART and USART
dt-bindings: serial: atmel,at91-usart: Add gclk as a possible USART clock
...
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently usbnet_disconnect() unanchors and frees all deferred URBs
using usb_scuttle_anchored_urbs(), which does not free urb->context,
causing a memory leak as reported by syzbot.
Use a usb_get_from_anchor() while loop instead, similar to what we did
in commit 19cfe912c3 ("Bluetooth: btusb: Fix memory leak in
play_deferred"). Also free urb->sg.
Reported-and-tested-by: syzbot+dcd3e13cf4472f2e0ba1@syzkaller.appspotmail.com
Fixes: 69ee472f27 ("usbnet & cdc-ether: Autosuspend for online devices")
Fixes: 638c5115a7 ("USBNET: support DMA SG")
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Link: https://lore.kernel.org/r/20220923042551.2745-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The Lenovo USB-C Travel Hub supports MAC passthrough.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152 driver does not disable multicasting when userspace asks
it to. For example:
$ ifconfig eth0 -multicast -allmulti
$ tcpdump -p -i eth0 # will still capture multicast frames
Fix by clearing the device multicast filter table when multicast and
allmulti are both unset.
Tested as follows:
- Set multicast on eth0 network interface
- verify that multicast packets are coming in:
$ tcpdump -p -i eth0
- Clear multicast and allmulti on eth0 network interface
- verify that no more multicast packets are coming in:
$ tcpdump -p -i eth0
Signed-off-by: Sven van Ashbrook <svenva@chromium.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20220830045923.net-next.v1.1.I4fee0ac057083d4f848caf0fa3a9fd466fc374a0@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phylink based ethtool pause configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some exotic ax88772 based devices which may require
functionality provide by the phylink framework. For example:
- US100A20SFP, USB 2.0 auf LWL Converter with SFP Cage
- AX88772B USB to 100Base-TX Ethernet (with RMII) demo board, where it
is possible to switch between internal PHY and external RMII based
connection.
So, convert this driver to phylink as soon as possible.
Tested with:
- AX88772A + internal PHY
- AX88772B + external DP83TD510E T1L PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX FIFO would be changed when suspending, so the related settings
have to be modified, too. Otherwise, the flow control would work
abnormally.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216333
Reported-by: Mark Blakeney <mark.blakeney@bullet-systems.net>
Fixes: cdf0b86b25 ("r8152: fix a WOL issue")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The units of PLA_RX_FIFO_FULL and PLA_RX_FIFO_EMPTY are 16 bytes.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Anker PowerExpand USB-C to Gigabit Ethernet adapter uses this
chipset, but exposes CDC Ethernet configurations as well as the
vendor specific one. This driver tries to bind by PID:VID
unconditionally and ends up picking up the CDC configuration, which
is supposed to be handled by the class driver. To make things even
more confusing, it sees both of the CDC class interfaces and tries
to bind twice, resulting in two broken Ethernet devices.
Change all the ID matches to specifically match the vendor-specific
interface. By default the device comes up in CDC mode and is bound by
that driver (which works fine); users may switch it to the vendor
interface using sysfs to set bConfigurationValue, at which point the
device actually goes through a reconnect cycle and comes back as a
vendor specific only device, and then this driver binds and works too.
The affected device uses VID/PID 0b95:1790, but we might as well change
all of them for good measure, since there is no good reason for this
driver to bind to standard CDC Ethernet interfaces.
v3: Added VID/PID info to commit message
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20220731072209.45504-1-marcan@marcan.st
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This refixes:
commit 7da17624e7
nt: usb: USB_RTL8153_ECM should not default to y
In general, device drivers should not be enabled by default.
which basically broke the commit it claimed to fix, ie:
commit 657bc1d10b
r8153_ecm: avoid to be prior to r8152 driver
Avoid r8153_ecm is compiled as built-in, if r8152 driver is compiled
as modules. Otherwise, the r8153_ecm would be used, even though the
device is supported by r8152 driver.
this commit amounted to:
drivers/net/usb/Kconfig:
+config USB_RTL8153_ECM
+ tristate "RTL8153 ECM support"
+ depends on USB_NET_CDCETHER && (USB_RTL8152 || USB_RTL8152=n)
+ default y
+ help
+ This option supports ECM mode for RTL8153 ethernet adapter, when
+ CONFIG_USB_RTL8152 is not set, or the RTL8153 device is not
+ supported by r8152 driver.
drivers/net/usb/Makefile:
-obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o r8153_ecm.o
+obj-$(CONFIG_USB_NET_CDCETHER) += cdc_ether.o
+obj-$(CONFIG_USB_RTL8153_ECM) += r8153_ecm.o
And as can be seen it pulls a piece of the cdc_ether driver out into
a separate config option to be able to make this piece modular in case
cdc_ether is builtin, while r8152 is modular.
While in general, device drivers should indeed not be enabled by default:
this isn't a device driver per say, but rather this is support code for
the CDCETHER (ECM) driver, and should thus be enabled if it is enabled.
See also email thread at:
https://www.spinics.net/lists/netdev/msg767649.html
In:
https://www.spinics.net/lists/netdev/msg768284.html
Jakub wrote:
And when we say "removed" we can just hide it from what's prompted
to the user (whatever such internal options are called)? I believe
this way we don't bring back Marek's complaint.
Side note: these incorrect defaults will result in Android 13
on 5.15 GKI kernels lacking USB_RTL8153_ECM support while having
USB_NET_CDCETHER (luckily we also have USB_RTL8150 and USB_RTL8152,
so it's probably only an issue for very new RTL815x hardware with
no native 5.15 driver).
Fixes: 7da17624e7 ("nt: usb: USB_RTL8153_ECM should not default to y")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20220730230113.4138858-1-zenczykowski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- Check if wol is supported on reset instead of everytime get_wol
is called.
- Save wolopts in private data instead of relying on the HW to save it.
- Defer enabling WoL until suspend instead of enabling it everytime
set_wol is called.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need more space to save WoL context. So lets allocate memory
for ax88179_data instead of using struct usbnet data field which
only supports 5 words. We continue to use the struct usbnet data
field for multicast filters. However since we no longer have the
private data stored there, we can shift it to the beginning.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware state was only partially restored, which meant certain
functionality was broken on resume. Do a full HW reset on resume to
fix this.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of passing in_pm flags all over the place, use the private
struct to handle in_pm mode.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bind and reset are basically doing the same thing. Remove the duplicate
code and have bind call into reset.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This improves performance and stability of
DL-3xxx/DL-5xxx/DL-6xxx device series.
Specifically prevents device from temporary network dropouts when
playing video from the web and network traffic going through is high.
Signed-off-by: Dominik Czerwik <dominik.czerwik@synaptics.com>
Signed-off-by: Łukasz Spintzyk <lukasz.spintzyk@synaptics.com>
Link: https://lore.kernel.org/r/20220720060518.541-1-lukasz.spintzyk@synaptics.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This fixes that the platform is waked by an unexpected packet. The
size and range of FIFO is different when the device enters S3 state,
so it is necessary to correct some settings when suspending.
Regardless of jumbo frame, set RMS to 1522 and MTPS to MTPS_DEFAULT.
Besides, enable MCU_BORW_EN to update the method of calculating the
pointer of data. Then, the hardware could get the correct data.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20220718082120.10957-391-nic_swsd@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A warning is triggered by commit 66e4c8d950 ("net: warn if transport
header was not set"). The warning is harmless, because the value from
skb_transport_offset() is only used for skb_is_gso() is true or the
skb->ip_summed is equal to CHECKSUM_PARTIAL.
Fixes: 66e4c8d950 ("net: warn if transport header was not set")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
usbnet_write_cmd_async() mixed up which buffers
need to be freed in which error case.
v2: add Fixes tag
v3: fix uninitialized buf pointer
Fixes: 877bd862f3 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220705125351.17309-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
smsc95xx_read_reg() and smsc95xx_write_reg() call BUG_ON() if the
struct usbnet pointer passed in is NULL.
The functions have just been amended to dereference the pointer on
entry. So the kernel now oopses if the pointer is NULL, eliminating
the need for an explicit BUG_ON().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN95xx driver has just been amended to auto-detect whether the
_nopm variant of usbnet_read_cmd() / usbnet_write_cmd() shall be used.
Drop all the now unnecessary open coding of that distinction.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05b35e7eb9 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw(). That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.
The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().
Commit b4df480f68 ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:
That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.
Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so. This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.
Stacktrace for posterity:
INFO: task kworker/2:1:49 blocked for more than 122 seconds.
Workqueue: usb_hub_wq hub_event
schedule
rpm_resume
__pm_runtime_resume
usb_autopm_get_interface
usbnet_read_cmd
__smsc95xx_read_reg
__smsc95xx_phy_wait_not_busy
__smsc95xx_mdio_read
smsc95xx_mdiobus_read
__mdiobus_read
mdiobus_read
smsc_phy_reset
phy_init_hw
smsc95xx_resume
usb_resume_interface
usb_resume_both
usb_runtime_resume
__rpm_callback
rpm_callback
rpm_resume
__pm_runtime_resume
usb_autoresume_device
hub_event
process_one_work
Fixes: b4df480f68 ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hasdata does not need to be initialized to zero. It will be assigned a
value in the following judgment conditions.
Signed-off-by: Li kunyu <kunyu@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver has long since be converted to dynamic debugging.
The internal compile options for more debugging can simply be
deleted.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220630110741.21314-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Either you use BIT(x) or 1 << x in the same expression.
Mixing them is ridiculous. Go to BIT()
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/microchip/sparx5/sparx5_switchdev.c
9c5de246c1 ("net: sparx5: mdb add/del handle non-sparx5 devices")
fbb89d02e3 ("net: sparx5: Allow mdb entries to both CPU and ports")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch corrects packet receiving in ax88179_rx_fixup.
- problem observed:
ifconfig shows allways a lot of 'RX Errors' while packets
are received normally.
This occurs because ax88179_rx_fixup does not recognise properly
the usb urb received.
The packets are normally processed and at the end, the code exits
with 'return 0', generating RX Errors.
(pkt_cnt==-2 and ptk_hdr over field rx_hdr trying to identify
another packet there)
This is a usb urb received by "tcpdump -i usbmon2 -X" on a
little-endian CPU:
0x0000: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
^ packet 1 start (pkt_len = 0x05ec)
^^^^ IP alignment pseudo header
^ ethernet packet start
last byte ethernet packet v
padding (8-bytes aligned) vvvv vvvv
0x05e0: c92d d444 1420 8a69 83dd 272f e82b 9811
0x05f0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 2
0x0be0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
...
0x1130: 9d41 9171 8a38 0ec5 eeee f8e3 3b19 87a0
...
0x1720: 8cfc 15ff 5e4c e85c eeee f8e3 3b19 87a0
...
0x1d10: ecfa 2a3a 19ab c78c eeee f8e3 3b19 87a0
...
0x2070: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 7
0x2120: 7c88 4ca5 5c57 7dcc 0d34 7577 f778 7e0a
0x2130: f032 e093 7489 0740 3008 ec05 0000 0080
====1==== ====2====
hdr_off ^
pkt_len = 0x05ec ^^^^
AX_RXHDR_*=0x00830 ^^^^ ^
pkt_len = 0 ^^^^
AX_RXHDR_DROP_ERR=0x80000000 ^^^^ ^
0x2140: 3008 ec05 0000 0080 3008 5805 0000 0080
0x2150: 3008 ec05 0000 0080 3008 ec05 0000 0080
0x2160: 3008 5803 0000 0080 3008 c800 0000 0080
===11==== ===12==== ===13==== ===14====
0x2170: 0000 0000 0e00 3821
^^^^ ^^^^ rx_hdr
^^^^ pkt_cnt=14
^^^^ hdr_off=0x2138
^^^^ ^^^^ padding
The dump shows that pkt_cnt is the number of entrys in the
per-packet metadata. It is "2 * packet count".
Each packet have two entrys. The first have a valid
value (pkt_len and AX_RXHDR_*) and the second have a
dummy-header 0x80000000 (pkt_len=0 with AX_RXHDR_DROP_ERR).
Why exists dummy-header for each packet?!?
My guess is that this was done probably to align the
entry for each packet to 64-bits and maintain compatibility
with old firmware.
There is also a padding (0x00000000) before the rx_hdr to
align the end of rx_hdr to 64-bit.
Note that packets have a alignment of 64-bits (8-bytes).
This patch assumes that the dummy-header and the last
padding are optional. So it preserves semantics and
recognises the same valid packets as the current code.
This patch was made using only the dumpfile information and
tested with only one device:
0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Fixes: 57bc3d3ae8 ("net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup")
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/d6970bb04bf67598af4d316eaeb1792040b18cfd.camel@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
usbnet provides some helper functions that are also used in
the context of reset() operations. During a reset the other
drivers on a device are unable to operate. As that can be block
drivers, a driver for another interface cannot use paging
in its memory allocations without risking a deadlock.
Use GFP_NOIO in the helpers.
Fixes: 877bd862f3 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220628093517.7469-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We should respect link partner capabilities and not force flow control
support on every link. Even more, in current state the MAC driver do not
advertises pause support so we should not keep flow control enabled at
all.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If cable is attached after probe sequence, the usbnet framework would
not automatically start processing RX packets except at least one
packet was transmitted.
On systems with any kind of address auto configuration this issue was
not detected, because some packets are send immediately after link state
is changed to "running".
With this patch we will notify usbnet about link status change provided by the
PHYlib.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
usbnet uses the work usbnet_deferred_kevent() to perform tasks which may
sleep. On disconnect, completion of the work was originally awaited in
->ndo_stop(). But in 2003, that was moved to ->disconnect() by historic
commit "[PATCH] USB: usbnet, prevent exotic rtnl deadlock":
https://git.kernel.org/tglx/history/c/0f138bbfd83c
The change was made because back then, the kernel's workqueue
implementation did not allow waiting for a single work. One had to wait
for completion of *all* work by calling flush_scheduled_work(), and that
could deadlock when waiting for usbnet_deferred_kevent() with rtnl_mutex
held in ->ndo_stop().
The commit solved one problem but created another: It causes a
use-after-free in USB Ethernet drivers aqc111.c, asix_devices.c,
ax88179_178a.c, ch9200.c and smsc75xx.c:
* If the drivers receive a link change interrupt immediately before
disconnect, they raise EVENT_LINK_RESET in their (non-sleepable)
->status() callback and schedule usbnet_deferred_kevent().
* usbnet_deferred_kevent() invokes the driver's ->link_reset() callback,
which calls netif_carrier_{on,off}().
* That in turn schedules the work linkwatch_event().
Because usbnet_deferred_kevent() is awaited after unregister_netdev(),
netif_carrier_{on,off}() may operate on an unregistered netdev and
linkwatch_event() may run after free_netdev(), causing a use-after-free.
In 2010, usbnet was changed to only wait for a single instance of
usbnet_deferred_kevent() instead of *all* work by commit 23f333a2bf
("drivers/net: don't use flush_scheduled_work()").
Unfortunately the commit neglected to move the wait back to
->ndo_stop(). Rectify that omission at long last.
Reported-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/netdev/CAG48ez0MHBbENX5gCdHAUXZ7h7s20LnepBF-pa5M=7Bi-jZrEA@mail.gmail.com/
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/netdev/20220315113841.GA22337@pengutronix.de/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/d1c87ebe9fc502bffcd1576e238d685ad08321e4.1655987888.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The extra byte inserted by usbnet.c when
(length % dev->maxpacket == 0) is causing problems to device.
This patch sets FLAG_SEND_ZLP to avoid this.
Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Problems observed:
======================================================================
1) Using ssh/sshfs. The remote sshd daemon can abort with the message:
"message authentication code incorrect"
This happens because the tcp message sent is corrupted during the
USB "Bulk out". The device calculate the tcp checksum and send a
valid tcp message to the remote sshd. Then the encryption detects
the error and aborts.
2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out
3) Stop normal work without any log message.
The "Bulk in" continue receiving packets normally.
The host sends "Bulk out" and the device responds with -ECONNRESET.
(The netusb.c code tx_complete ignore -ECONNRESET)
Under normal conditions these errors take days to happen and in
intense usage take hours.
A test with ping gives packet loss, showing that something is wrong:
ping -4 -s 462 {destination} # 462 = 512 - 42 - 8
Not all packets fail.
My guess is that the device tries to find another packet starting
at the extra byte and will fail or not depending on the next
bytes (old buffer content).
======================================================================
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Microchip's EVB-LAN8670-USB 10BASE-T1S
ethernet device to the existing smsc95xx driver by adding the new
USB VID/PID pairs.
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit 316580b69d ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for the
USB core, but there are the usual "hot spots" of development activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes. It seems this driver will never
be finished given that the IP core is showing up in zillions
of new devices and each implementation decides to do something
different with it...
- uvc gadget driver updates as more devices start to use and
rely on this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnZGw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymQhwCeLVANsQjBcL4ys4skl+1In17y28gAn3rEZ7rQ
Yv4uP9zadUqg3Cx0vjgf
=3s5s
-----END PGP SIGNATURE-----
Merge tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
Add support for Telit LN910Cx 0x1250 composition
0x1250: rmnet, tty, tty, tty, tty
Signed-off-by: Carlo Lobrano <c.lobrano@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lenovo Thunderbolt 4 Dock, and other Lenovo USB Docks are using the
original Realtek USB ethernet Vendor and Product IDs
If the Network device is Realtek verify that it is on a Lenovo USB hub
before enabling the passthru feature
This also adds in the device IDs for the Lenovo USB Dongle and one other
USB-C dock
V2 fix formating of code
V3 remove Generic define for Device ID 0x8153 and change it to use value
V4 rearrange defines and case statement to put them in better order
v5 create helper function to do the testing work as suggested
Signed-off-by: David Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20220517180539.25839-1-dober6023@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link status of SMSC LAN95xx chips is polled once per second, even though
they're capable of signaling PHY interrupts through the MAC layer.
Forward those interrupts to the PHY driver to avoid polling. Benefits
are reduced bus traffic, reduced CPU overhead and quicker interface
bringup.
Polling was introduced in 2016 by commit d69d169493 ("usbnet:
smsc95xx: fix link detection for disabled autonegotiation").
Back then, the LAN95xx driver neglected to enable the ENERGYON interrupt,
hence couldn't detect link-up events when auto-negotiation was disabled.
The proper solution would have been to enable the ENERGYON interrupt
instead of polling.
Since then, PHY handling was moved from the LAN95xx driver to the SMSC
PHY driver with commit 05b35e7eb9 ("smsc95xx: add phylib support").
That PHY driver is capable of link detection with auto-negotiation
disabled because it enables the ENERGYON interrupt.
Note that signaling interrupts through the MAC layer not only works with
the integrated PHY, but also with an external PHY, provided its
interrupt pin is attached to LAN95xx's nPHY_INT pin.
In the unlikely event that the interrupt pin of an external PHY is
attached to a GPIO of the SoC (or not connected at all), the driver can
be amended to retrieve the irq from the PHY's of_node.
To forward PHY interrupts to phylib, it is not sufficient to call
phy_mac_interrupt(). Instead, the PHY's interrupt handler needs to run
so that PHY interrupts are cleared. That's because according to page
119 of the LAN950x datasheet, "The source of this interrupt is a level.
The interrupt persists until it is cleared in the PHY."
https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf
Therefore, create an IRQ domain with a single IRQ for the PHY. In the
future, the IRQ domain may be extended to support the 11 GPIOs on the
LAN95xx.
Normally the PHY interrupt should be masked until the PHY driver has
cleared it. However masking requires a (sleeping) USB transaction and
interrupts are received in (non-sleepable) softirq context. I decided
not to mask the interrupt at all (by using the dummy_irq_chip's noop
->irq_mask() callback): The USB interrupt endpoint is polled in 1 msec
intervals and normally that's sufficient to wake the PHY driver's IRQ
thread and have it clear the interrupt. If it does take longer, worst
thing that can happen is the IRQ thread is woken again. No big deal.
Because PHY interrupts are now perpetually enabled, there's no need to
selectively enable them on suspend. So remove all invocations of
smsc95xx_enable_phy_wakeup_interrupts().
In smsc95xx_resume(), move the call of phy_init_hw() before
usbnet_resume() (which restarts the status URB) to ensure that the PHY
is fully initialized when an interrupt is handled.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch> # from a PHY perspective
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the
MAC full duplex mode and PHY flow control registers based on cached data
in struct phy_device:
smsc95xx_status() # raises EVENT_LINK_RESET
usbnet_deferred_kevent()
smsc95xx_link_reset() # uses cached data in phydev
Simultaneously, phylib polls link status once per second and updates
that cached data:
phy_state_machine()
phy_check_link_status()
phy_read_status()
lan87xx_read_status()
genphy_read_status() # updates cached data in phydev
If smsc95xx_link_reset() wins the race against genphy_read_status(),
the registers may be updated based on stale data.
E.g. if the link was previously down, phydev->duplex is set to
DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even
though genphy_read_status() may update it to DUPLEX_FULL afterwards.
PHY interrupts are currently only enabled on suspend to trigger wakeup,
so the impact of the race is limited, but we're about to enable them
perpetually.
Avoid the race by delaying execution of smsc95xx_link_reset() until
phy_state_machine() has done its job and calls back via
smsc95xx_handle_link_change().
Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib
picks up link status changes through polling. So drop the declaration
of a ->link_reset() callback.
Note that the semicolon on a line by itself added in smsc95xx_status()
is a placeholder for a function call which will be added in a subsequent
commit. That function call will actually handle the INT_ENP_PHY_INT_
interrupt.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc95xx_reset() resets the PHY behind the PHY driver's back, which
seems like a bad idea generally. Remove that portion of the function.
We're about to use PHY interrupts instead of polling to detect link
changes on SMSC LAN95xx chips. Because smsc95xx_reset() is called from
usbnet_open(), PHY interrupt settings are lost whenever the net_device
is brought up.
There are two other callers of smsc95xx_reset(), namely smsc95xx_bind()
and smsc95xx_reset_resume(), and both may indeed benefit from a PHY
reset. However they already perform one through their calls to
phy_connect_direct() and phy_init_hw().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Gabriel Hojda <ghojda@yo2urs.ro>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver
attempts to clear the signaled interrupts by writing "all ones" to the
Interrupt Status Register.
However the driver only ever enables a single type of interrupt, namely
the PHY Interrupt. And according to page 119 of the LAN950x datasheet,
its bit in the Interrupt Status Register is read-only. There's no other
way to clear it than in a separate PHY register:
https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf
Consequently, writing "all ones" to the Interrupt Status Register is
pointless and can be dropped.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2c9d6c2b87 ("usbnet: run unbind() before unregister_netdev()")
sought to fix a use-after-free on disconnect of USB Ethernet adapters.
It turns out that a different fix is necessary to address the issue:
https://lore.kernel.org/netdev/18b3541e5372bc9b9fc733d422f4e698c089077c.1650177997.git.lukas@wunner.de/
So the commit was not necessary.
The commit made binding and unbinding of USB Ethernet asymmetrical:
Before, usbnet_probe() first invoked the ->bind() callback and then
register_netdev(). usbnet_disconnect() mirrored that by first invoking
unregister_netdev() and then ->unbind().
Since the commit, the order in usbnet_disconnect() is reversed and no
longer mirrors usbnet_probe().
One consequence is that a PHY disconnected (and stopped) in ->unbind()
is afterwards stopped once more by unregister_netdev() as it closes the
netdev before unregistering. That necessitates a contortion in ->stop()
because the PHY may only be stopped if it hasn't already been
disconnected.
Reverting the commit allows making the call to phy_stop() unconditional
in ->stop().
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 uses a custom napi weight, switch to the new
API for setting custom weight.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmJu9FYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGAyEH/16xtJSpLmLwrQzG
o+4ToQxSQ+/9UHyu0RTEvHg2THm9/8emtIuYyc/5FgdoWctcSa3AaDcveWmuWmkS
KYcdhfJsaEqjNHS3OPYXN84fmo9Hel7263shu5+IYmP/sN0DfQp6UWTryX1q4B3Q
4Pdutkuq63Uwd8nBZ5LXQBumaBrmkkuMgWEdT4+6FOo1mPzwdIGBxCuz1UsNNl5k
chLWxkQfe2eqgWbYJrgCQfrVdORXVtoU2fGilZUNrHRVGkkldXkkz5clJfapyZD3
odmZCEbrE4GPKgZwCmDERMfD1hzhZDtYKiHfOQ506szH5ykJjPBcOjHed7dA60eB
J3+wdek=
=39Ca
-----END PGP SIGNATURE-----
Merge 5.18-rc5 into usb-next
We need the USB fixes in here, and this resolves a merge issue in
drivers/usb/dwc3/drd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The third argument of usb_maxpacket(): in_out has been deprecated
because it could be derived from the second argument (e.g. using
usb_pipeout(pipe)).
N.B. function usb_maxpacket() was made variadic to accommodate the
transition from the old prototype with three arguments to the new one
with only two arguments (so that no renaming is needed). The variadic
argument is to be removed once all users of usb_maxpacket() get
migrated.
CC: Oliver Neukum <oliver@neukum.org>
CC: David S. Miller <davem@davemloft.net>
CC: Jakub Kicinski <kuba@kernel.org>
CC: Woojung Huh <woojung.huh@microchip.com>
CC: Felix Fietkau <nbd@nbd.name>
CC: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
CC: Ryder Lee <ryder.lee@mediatek.com>
CC: Kalle Valo <kvalo@kernel.org>
CC: Matthias Brugger <matthias.bgg@gmail.com>
CC: Stanislaw Gruszka <stf_xl@wp.pl>
CC: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20220317035514.6378-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch reports this issue
sr9800.h:166:53: warning: symbol 'SR9800_BULKIN_SIZE' was not declared. Should it be static?
Global variables should not be defined in header files.
This only works because sr9800.h in only included by sr9800.c
Change the storage-class specifier to static.
And since it does not change add type qualifier const.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unnecessary to call spin_lock_bh() for you are already in a tasklet.
Signed-off-by: Yunbo Yu <yuyunbo519@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reporting of bogus MAC addresses and ignoring configuration of new
destination address wasn't observed outside of a range of ZTE devices,
among which this seems to be the common bug. Align rndis_host driver
with implementation found in cdc_ether, which also limits this workaround
to ZTE devices.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Certain ZTE modems, namely: MF823. MF831, MF910, built-in modem from
MF286R, expose both CDC-ECM and RNDIS network interfaces.
They have a trait of ignoring the locally-administered MAC address
configured on the interface both in CDC-ECM and RNDIS part,
and this leads to dropping of incoming traffic by the host.
However, the workaround was only present in CDC-ECM, and MF286R
explicitly requires it in RNDIS mode.
Re-use the workaround in rndis_host as well, to fix operation of MF286R
module, some versions of which expose only the RNDIS interface. Do so by
introducing new flag, RNDIS_DRIVER_DATA_DST_MAC_FIXUP, and testing for it
in rndis_rx_fixup. This is required, as RNDIS uses frame batching, and all
of the packets inside the batch need the fixup. This might introduce a
performance penalty, because test is done for every returned Ethernet
frame.
Apply the workaround to both "flavors" of RNDIS interfaces, as older ZTE
modems, like MF823 found in the wild, report the USB_CLASS_COMM class
interfaces, while MF286R reports USB_CLASS_WIRELESS_CONTROLLER.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit bfe9b9d2df ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduces a workaround for certain ZTE modems reporting invalid MAC
addresses over CDC-ECM.
The same issue was present on their RNDIS interface,which was fixed in
commit a5a18bdf74 ("rndis_host: Set valid random MAC on buggy devices").
However, internal modem of ZTE MF286R router, on its RNDIS interface, also
exhibits a second issue fixed already in CDC-ECM, of the device not
respecting configured random MAC address. In order to share the fixup for
this with rndis_host driver, export the workaround function, which will
be re-used in the following commit in rndis_host.
Cc: Kristian Evensen <kristian.evensen@gmail.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
aqc111_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
Found doing variant analysis. Tested it with another driver (ax88179_178a), since
I don't have a aqc111 device to test it, but the code looks very similar.
Signed-off-by: Marcin Kozlowski <marcinguy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_alloc_skb() has assigned ssi->netdev to skb->dev if successed,
no need to repeat assignment.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout
the stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower
iTLB pressure and prevents identity mapping huge pages from
getting split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop
the user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if called
from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling
of TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ELpe
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
In case external PHY is used, we need to take care of embedded PHY.
Since there are no methods to disable this PHY from the MAC side and
keeping RMII reference clock, we need to suspend it.
This patch will reduce electrical noise (PHY is continuing to send FLPs)
and power consumption by 0,22W.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In most cases we use own mdio bus, there is no need to create and store
string for the PHY address.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already read chipid on probe. There is no need to read it on reset.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only difference is the reset code, so remove not needed duplicates.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/driver-api/usb/URB.rst when a device
is unplugged usb_submit_urb() returns -ENODEV.
This error code propagates all the way up to usbnet_read_cmd() and
usbnet_write_cmd() calls inside the smsc95xx.c driver during
Ethernet cable unplug, unbind or reboot.
This causes the following errors to be shown on reboot, for example:
ci_hdrc ci_hdrc.1: remove, state 1
usb usb2: USB disconnect, device number 1
usb 2-1: USB disconnect, device number 2
usb 2-1.1: USB disconnect, device number 3
smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup
usb 2-1.4: USB disconnect, device number 4
ci_hdrc ci_hdrc.1: USB bus 2 deregistered
ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot!
reboot: Restarting system
Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and
__smsc95xx_phy_wait_not_busy() and do not print error messages
when -ENODEV is returned.
Fixes: a049a30fc2 ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of manually disabling interrupts before invoking use
generic_handle_irq_safe() which can be invoked with enabled and disabled
interrupts.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: UNGLinuxDriver@microchip.com
Link: https://lore.kernel.org/r/20220211181500.1856198-7-bigeasy@linutronix.de
This functions are mostly same except of one hard coded "in_pm" variable.
So, rework them to reduce maintenance overhead.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220223110633.3006551-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices,
avoid FW assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmIOm44ACgkQMUZtbf5S
IruWWBAAmNJBxVoVUahidwIVKHnKYeHClzDee3B6sYSupRW22Eeuh7Q8fqPMO4J7
KO9nP/vGibFuhKfjApvS6wPvpYWCuXAoSozfOa+JWNrFg9uVpdyHIhfdXl0WPZqx
A4+p2vIs1ldV0yOac/7ZGMWg57dzlYUurkld3xFwf7KyOOhV5/PkxkxpGN9eFkv1
NTFWTaIsVzFMXMjNXkGfGHmt/8mSmZHgsH+tYd+KXsjbs2UpbGM3SyfHBlUf3aA0
bceT4h07xA6C4rlUCbmalRqwvtcdM15MwlDBtSBXm5fXy0c59XxQOqj/dLhPuAO4
42sQlO2MhqDrZjR0tOjmuP2cpc7llj1lIZe1Qs3nKiNFHcuOJEHGw1PYCO85jKdn
xiWquuoe3G5YkQeoOoi+HqmXcP6aBZpUbROvYNjSJhcci4Ck0Qjna5J1rk8IRjb8
AkDf68dodn8I+W5dx/EnopH/ShPQcqGw1+tH4215UB7b40Ecpc+laqFAHRcgs654
ONuJVdRC4k3TyES1B9z8vawLcGYWa06fz8Mh/dS3gnLDphe5ZiH2tTrESfBdYixH
idmuO5C/YDhsVelVuO+B0RT/yziPb3Lr+BTplSfkODCXT6LuOdCYUcHx5nGZ1TYW
EeZ9hMSaxp2E06llEyD6JQQ+0Q17wnDGjLxtOMk+A8fmNX2F17g=
=Nrzq
-----END PGP SIGNATURE-----
Merge tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless and netfilter.
Current release - regressions:
- dsa: lantiq_gswip: fix use after free in gswip_remove()
- smc: avoid overwriting the copies of clcsock callback functions
Current release - new code bugs:
- iwlwifi:
- fix use-after-free when no FW is present
- mei: fix the pskb_may_pull check in ipv4
- mei: retry mapping the shared area
- mvm: don't feed the hardware RFKILL into iwlmei
Previous releases - regressions:
- ipv6: mcast: use rcu-safe version of ipv6_get_lladdr()
- tipc: fix wrong publisher node address in link publications
- iwlwifi: mvm: don't send SAR GEO command for 3160 devices, avoid FW
assertion
- bgmac: make idm and nicpm resource optional again
- atl1c: fix tx timeout after link flap
Previous releases - always broken:
- vsock: remove vsock from connected table when connect is
interrupted by a signal
- ping: change destination interface checks to match raw sockets
- crypto: af_alg - get rid of alg_memory_allocated to avoid confusing
semantics (and null-deref) after SO_RESERVE_MEM was added
- ipv6: make exclusive flowlabel checks per-netns
- bonding: force carrier update when releasing slave
- sched: limit TC_ACT_REPEAT loops
- bridge: multicast: notify switchdev driver whenever MC processing
gets disabled because of max entries reached
- wifi: brcmfmac: fix crash in brcm_alt_fw_path when WLAN not found
- iwlwifi: fix locking when "HW not ready"
- phy: mediatek: remove PHY mode check on MT7531
- dsa: mv88e6xxx: flush switchdev FDB workqueue before removing VLAN
- dsa: lan9303:
- fix polarity of reset during probe
- fix accelerated VLAN handling"
* tag 'net-5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
bonding: force carrier update when releasing slave
nfp: flower: netdev offload check for ip6gretap
ipv6: fix data-race in fib6_info_hw_flags_set / fib6_purge_rt
ipv4: fix data races in fib_alias_hw_flags_set
net: dsa: lan9303: add VLAN IDs to master device
net: dsa: lan9303: handle hwaccel VLAN tags
vsock: remove vsock from connected table when connect is interrupted by a signal
Revert "net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname"
ping: fix the dif and sdif check in ping_lookup
net: usb: cdc_mbim: avoid altsetting toggling for Telit FN990
net: sched: limit TC_ACT_REPEAT loops
tipc: fix wrong notification node addresses
net: dsa: lantiq_gswip: fix use after free in gswip_remove()
ipv6: per-netns exclusive flowlabel checks
net: bridge: multicast: notify switchdev driver whenever MC processing gets disabled
CDC-NCM: avoid overflow in sanity checking
mctp: fix use after free
net: mscc: ocelot: fix use-after-free in ocelot_vlan_del()
bonding: fix data-races around agg_select_timer
dpaa2-eth: Initialize mutex used in one step timestamping path
...
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
hso_create_device() is only called from function that already use
GFP_KERNEL. And all the callers are called from the probe function.
So there is no need here to explicitly require a GFP_ATOMIC when
allocating memory.
Use GFP_KERNEL instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This SL-6000 says Direct Line, not Ethernet
v2: added Reporter and Link
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: Ross Maynard <bids.7405@bigpond.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215361
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some small USB driver fixes for 5.17-rc4 that resolve some
reported issues and add new device ids:
- usb-serial new device ids
- ulpi cleanup fixes
- f_fs use-after-free fix
- dwc3 driver fixes
- ax88179_178a usb network driver fix
- usb gadget fixes
There is a revert at the end of this series to resolve a build problem
that 0-day found yesterday. Most of these have been in linux-next,
except for the last few, and all have now passed 0-day tests.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYgeLiw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylpQACaAnwfFoAxK5yr2IEu5WmxPmY0pSkAnROqF4JO
CQhohQ61DjpdK0ikJWsZ
=n8Yn
-----END PGP SIGNATURE-----
Merge tag 'usb-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 5.17-rc4 that resolve some
reported issues and add new device ids:
- usb-serial new device ids
- ulpi cleanup fixes
- f_fs use-after-free fix
- dwc3 driver fixes
- ax88179_178a usb network driver fix
- usb gadget fixes
There is a revert at the end of this series to resolve a build problem
that 0-day found yesterday. Most of these have been in linux-next,
except for the last few, and all have now passed 0-day tests"
* tag 'usb-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
Revert "usb: dwc2: drd: fix soft connect when gadget is unconfigured"
usb: dwc2: drd: fix soft connect when gadget is unconfigured
usb: gadget: rndis: check size of RNDIS_MSG_SET command
USB: gadget: validate interface OS descriptor requests
usb: core: Unregister device on component_add() failure
net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup
usb: dwc3: gadget: Prevent core from processing stale TRBs
USB: serial: cp210x: add CPI Bulk Coin Recycler id
USB: serial: cp210x: add NCR Retail IO box id
USB: serial: ftdi_sio: add support for Brainboxes US-159/235/320
usb: gadget: f_uac2: Define specific wTerminalType
usb: gadget: udc: renesas_usb3: Fix host to USB_ROLE_NONE transition
usb: raw-gadget: fix handling of dual-direction-capable endpoints
usb: usb251xb: add boost-up property support
usb: ulpi: Call of_node_put correctly
usb: ulpi: Move of_node_put to ulpi_dev_release
USB: serial: option: add ZTE MF286D modem
USB: serial: ch341: add support for GW Instek USB2.0-Serial devices
usb: f_fs: Fix use-after-free for epfile
usb: dwc3: xilinx: fix uninitialized return value
ax88179_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (hdr_off..hdr_off+2*pkt_cnt) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
I have tested that this can be used by a malicious USB device to send a
bogus ICMPv6 Echo Request and receive an ICMPv6 Echo Reply in response
that contains random kernel heap data.
It's probably also possible to get OOB writes from this on a
little-endian system somehow - maybe by triggering skb_cow() via IP
options processing -, but I haven't tested that.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provide generic selftest support. Tested with LAN9500 and LAN9512.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot once again hit uninit value in asix driver. The problem still the
same -- asix_read_cmd() reads less bytes, than was requested by caller.
Since all read requests are performed via asix_read_cmd() let's catch
usb related error there and add __must_check notation to be sure all
callers actually check return value.
So, this patch adds sanity check inside asix_read_cmd(), that simply
checks if bytes read are not less, than was requested and adds missing
error handling of asix_read_cmd() all across the driver code.
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+6ca9f7867b77c2d316ac@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rx_buf is allocated we need to account for IPHETH_IP_ALIGN,
which reduces the usable size by 2 bytes. Otherwise we have 1512
bytes usable instead of 1514, and if we receive more than 1512
bytes, ipheth_rcvbulk_callback is called with status -EOVERFLOW,
after which the driver malfunctiones and all communication stops.
Resolves ipheth 2-1:4.2: ipheth_rcvbulk_callback: urb status: -75
Fixes: f33d9e2b48 ("usbnet: ipheth: fix connectivity with iOS 14")
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/all/B60B8A4B-92A0-49B3-805D-809A2433B46C@abv.bg/
Link: https://lore.kernel.org/all/24851bd2769434a5fc24730dce8e8a984c5a4505.1643699778.git.jan.kiszka@siemens.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Variable reg is being masked however the variable is never read
after this. The assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220123184035.112785-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On boards with LAN9514 and no preconfigured MAC address we don't get an
ip address from DHCP after commit a049a30fc2 ("net: usb: Correct PHY handling
of smsc95xx") anymore. Adding an explicit reset before starting the phy
fixes the issue.
[1]
https://lore.kernel.org/netdev/199eebbd6b97f52b9119c9fa4fd8504f8a34de18.camel@collabora.com/
From: Gabriel Hojda <ghojda@yo2urs.ro>
Fixes: a049a30fc2 ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Gabriel Hojda <ghojda@yo2urs.ro>
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported uninit value in mcs7830_bind(). The problem was in
missing validation check for bytes read via usbnet_read_cmd().
usbnet_read_cmd() internally calls usb_control_msg(), that returns
number of bytes read. Code should validate that requested number of bytes
was actually read.
So, this patch adds missing size validation check inside
mcs7830_get_reg() to prevent uninit value bugs
Reported-and-tested-by: syzbot+003c0a286b9af5412510@syzkaller.appspotmail.com
Fixes: 2a36d70834 ("USB: driver for mcs7830 (aka DeLOCK) USB ethernet adapter")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220106225716.7425-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit f77b83b5bb.
This change breaks multiple usb to ethernet dongles attached on Lenovo
USB hub.
Fixes: f77b83b5bb ("net: usb: r8152: Add MAC passthrough support for more Lenovo Docks")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Link: https://lore.kernel.org/r/20220105155102.8557-1-aaron.ma@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hytera makes a range of digital (DMR) radios. These radios can be
programmed to a allow a computer to control them over Ethernet over USB,
either using NCM or RNDIS.
This commit adds support for RNDIS for Hytera radios. I tested with a
Hytera PD785 and a Hytera MD785G. When these radios are programmed to
set up a Radio to PC Network using RNDIS, an USB interface will be added
with class 2 (Communications), subclass 2 (Abstract Modem Control) and
an interface protocol of 255 ("vendor specific" - lsusb even hints "MSFT
RNDIS?").
This patch is similar to the solution of this StackOverflow user, but
that only works for the Hytera MD785:
https://stackoverflow.com/a/53550858
To use the "Radio to PC Network" functionality of Hytera DMR radios, the
radios need to be programmed correctly in CPS (Hytera's Customer
Programming Software). "Forward to PC" should be checked in "Network"
(under "General Setting" in "Conventional") and the "USB Network
Communication Protocol" should be set to RNDIS.
Signed-off-by: Thomas Toye <thomas@toye.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames
that are longer than 1518 octets, for example, Ethernet frames that
contain 802.1Q VLAN tags.
The frames are sent to the pegasus driver via USB but the driver
discards them because they have the Long_pkt field set to 1 in the
received status report. The function read_bulk_callback of the pegasus
driver treats such received "packets" (in the terminology of the
hardware) as errors but the field simply does just indicate that the
Ethernet frame (MAC destination to FCS) is longer than 1518 octets.
It seems that in the 1990s there was a distinction between
"giant" (> 1518) and "runt" (< 64) frames and the hardware includes
flags to indicate this distinction. It seems that the purpose of the
distinction "giant" frames was to not allow infinitely long frames due
to transmission errors and to allow hardware to have an upper limit of
the frame size. However, the hardware already has such limit with its
2048 octet receive buffer and, therefore, Long_pkt is merely a
convention and should not be treated as a receive error.
Actually, the hardware is even able to receive Ethernet frames with 2048
octets which exceeds the claimed limit frame size limit of the driver of
1536 octets (PEGASUS_MTU).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Matthias-Christian Ott <ott@mirix.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some chances that the actual base of hardware is different
from the value recorded by driver, so we have to reset the variable
of ocp_base to sync it.
Set ocp_base to -1. Then, it would be updated and the new base would be
set to the hardware next time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It needs to set mdio force mode. Otherwise, link off always occurs when
setting force speed.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If asix_read_cmd() returns 0 on 30th interation, 0 will be returned from
asix_check_host_enable(), which is logically wrong. Fix it by returning
-ETIMEDOUT explicitly if we have exceeded 30 iterations
Also, replaced 30 with #define as suggested by Andrew
Fixes: a786e3195d ("net: asix: fix uninit value bugs")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/ecd3470ce6c2d5697ac635d0d3b14a47defb4acb.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
asix_read_cmd() may read less than sizeof(smsr) bytes and in this case
smsr will be uninitialized.
Fail log:
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
BUG: KMSAN: uninit-value in asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
BUG: KMSAN: uninit-value in asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline]
asix_check_host_enable drivers/net/usb/asix_common.c:82 [inline] drivers/net/usb/asix_common.c:497
asix_mdio_read+0x3c1/0xb00 drivers/net/usb/asix_common.c:497 drivers/net/usb/asix_common.c:497
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-and-tested-by: syzbot+f44badb06036334e867a@syzkaller.appspotmail.com
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/8966e3b514edf39857dd93603fc79ec02e000a75.1640117288.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff830a5b5f len:184 put:172 \
head:ffff888119227c00 data:ffff888119227c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:110!
RIP: 0010:skb_panic+0x14f/0x160 net/core/skbuff.c:106
<snip>
Call Trace:
<IRQ>
skb_over_panic+0x2c/0x30 net/core/skbuff.c:115
skb_put+0x205/0x210 net/core/skbuff.c:1877
skb_put_zero include/linux/skbuff.h:2270 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1116 [inline]
cdc_ncm_fill_tx_frame+0x127f/0x3d50 drivers/net/usb/cdc_ncm.c:1293
cdc_ncm_tx_fixup+0x98/0xf0 drivers/net/usb/cdc_ncm.c:1514
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org>
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a3 ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a NAPI-style approach for processing completed
Rx URBs that contributes to improving driver throughput and reducing
CPU load.
Packets in completed URBs are copied to NAPI SKBs and passed to the
network stack for processing. Each frame passed to the stack is one
work item in the NAPI budget.
If the NAPI budget is consumed and frames remain, they are added to
an overflow queue that is processed at the start of the next NAPI
polling cycle.
The NAPI handler is also responsible for copying pending Tx data to
Tx URBs and submitting them to the USB host controller for
transmission.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove hardware-specific header length adjustment as it is no longer
required. It also breaks generic receive offload (GRO) processing of
received TCP frames that results in a TCP ACK being sent for each
received frame.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move position of rx_submit() to remove forward declaration of
rx_complete() which is now no longer required.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new approach to allocating and managing
Rx URBs that contributes to improving driver throughput and reducing
CPU load.
A pool of Rx URBs is created during driver instantiation. All the
URBs are initially submitted to the USB host controller for
processing.
The default URB buffer size is different for each USB bus speed.
The chosen sizes provide good USB utilisation with little impact on
overall packet latency.
Completed URBs are processed in the driver bottom half. The URB
buffer contents are copied to a dynamically allocated SKB, which is
then passed to the network stack. The URB is then re-submitted to
the USB host controller.
NOTE: the call to skb_copy() in rx_process() that copies the URB
contents to a new SKB is a temporary change to make this patch work
in its own right. This call will be removed when the NAPI processing
is introduced by patch 6 in this patch set.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new approach to allocating and managing
Tx URBs that contributes to improving driver throughput and reducing
CPU load.
A pool of Tx URBs is created during driver instantiation. A URB is
allocated from the pool when there is data to transmit. The URB is
released back to the pool when the data has been transmitted by the
device.
The default URB buffer size is different for each USB bus speed.
The chosen sizes provide good USB utilisation with little impact on
overall packet latency.
SKBs to be transmitted are added to a pending queue for processing.
The driver tracks the available Tx URB buffer space and copies as
much pending data as possible into each free URB. Each full URB
is then submitted to the USB host controller for transmission.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory allocation that fails to check for NULL return.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like ThinkaPad Thunderbolt 4 Dock, more Lenovo docks start to use the original
Realtek USB ethernet chip ID 0bda:8153.
Lenovo Docks always use their own IDs for usb hub, even for older Docks.
If parent hub is from Lenovo, then r8152 should try MAC passthrough.
Verified on Lenovo TBT3 dock too.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On low-effciency embedded platforms, transmission performance is poor
due to on Bulk-out with single packet.
Adding TSO feature improves the transmission performance and reduces
the number of interrupt caused by Bulk-out complete.
Reference to module, net: usb: aqc111.
Signed-off-by: Jacky Chou <jackychou@asix.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return error code if usb_maxpacket() returns 0 in usbnet_probe()
Fixes: 397430b50a ("usbnet: sanity check for maxpacket")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20211026124015.3025136-1-wanghai38@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in lan78xx_tx_bh() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Cc: stable@vger.kernel.org # 4.3
Cc: Woojung.Huh@microchip.com <Woojung.Huh@microchip.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
In the case of catc we need a new temporary buffer to conform
to the rules for DMA coherency. That in turn necessitates
a reworking of error handling in probe().
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Manually fix all net/usb drivers without separate maintainers.
v2: catc does DMA to the buffer, leave the conversion to Oliver
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A handful of drivers use sizeof(addr) for the size of
the address, after manually confirming the size is
indeed 6 convert them to eth_hw_addr_set().
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the drivers which use single-byte netdev addresses
(netdev->addr_len == 1) use the appropriate address setting
helpers.
arcnet copies from int variables and io reads a lot, so
add a helper for arcnet drivers to use.
Similar helper could be reused for phonet and appletalk
but there isn't any good central location where we could
put it, and netdevice.h is already very crowded.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for HSI
Link: https://lore.kernel.org/r/20211012142757.4124842-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the following build/link errors by adding a dependency on
CRYPTO, CRYPTO_HASH, CRYPTO_SHA256 and CRC32:
ld: drivers/net/usb/r8152.o: in function `rtl8152_fw_verify_checksum':
r8152.c:(.text+0x2b2a): undefined reference to `crypto_alloc_shash'
ld: r8152.c:(.text+0x2bed): undefined reference to `crypto_shash_digest'
ld: r8152.c:(.text+0x2c50): undefined reference to `crypto_destroy_tfm'
ld: drivers/net/usb/r8152.o: in function `_rtl8152_set_rx_mode':
r8152.c:(.text+0xdcb0): undefined reference to `crc32_le'
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new platform_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, net;
@@
- eth_platform_get_mac_address(dev, net->dev_addr)
+ platform_get_ethdev_address(dev, net)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert usb drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
Manually checked these are either usbnet or pure etherdevs.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the situation that the disconnect event comes very late when the
device is unplugged, the driver would resubmit the RX bulk transfer
after getting the callback with -EPROTO immediately and continually.
Finally, soft lockup occurs.
This patch avoids to resubmit RX immediately. It uses a workqueue to
schedule the RX NAPI. And the NAPI would resubmit the RX. It let the
disconnect event have opportunity to stop the submission before soft
lockup.
Reported-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Tested-by: Jason-ch Chen <jason-ch.chen@mediatek.com>
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert net/usb from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Convert usb drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 05b35e7eb9 ("smsc95xx: add phylib support"), link changes
are no longer propagated to usbnet. As a result, rx URB allocation won't
happen until there is a packet sent out first (this might never happen,
e.g. running just ssh server with a static IP). Fix by triggering usbnet
EVENT_LINK_CHANGE.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
If resource allocation and registration fail for a muxed tty device
(e.g. if there are no more minor numbers) the driver should not try to
deregister the never-registered (or already-deregistered) tty.
Fix up the error handling to avoid dereferencing a NULL pointer when
attempting to remove the character device.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL
address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Zvuz
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes and stragglers from Jakub Kicinski:
"Networking stragglers and fixes, including changes from netfilter,
wireless and can.
Current release - regressions:
- qrtr: revert check in qrtr_endpoint_post(), fixes audio and wifi
- ip_gre: validate csum_start only on pull
- bnxt_en: fix 64-bit doorbell operation on 32-bit kernels
- ionic: fix double use of queue-lock, fix a sleeping in atomic
- can: c_can: fix null-ptr-deref on ioctl()
- cs89x0: disable compile testing on powerpc
Current release - new code bugs:
- bridge: mcast: fix vlan port router deadlock, consistently disable
BH
Previous releases - regressions:
- dsa: tag_rtl4_a: fix egress tags, only port 0 was working
- mptcp: fix possible divide by zero
- netfilter: nft_ct: protect nft_ct_pcpu_template_refcnt with mutex
- netfilter: socket: icmp6: fix use-after-scope
- stmmac: fix MAC not working when system resume back with WoL active
Previous releases - always broken:
- ip/ip6_gre: use the same logic as SIT interfaces when computing
v6LL address
- seg6: set fc_nlinfo in nh_create_ipv4, nh_create_ipv6
- mptcp: only send extra TCP acks in eligible socket states
- dsa: lantiq_gswip: fix maximum frame length
- stmmac: fix overall budget calculation for rxtx_napi
- bnxt_en: fix firmware version reporting via devlink
- renesas: sh_eth: add missing barrier to fix freeing wrong tx
descriptor
Stragglers:
- netfilter: conntrack: switch to siphash
- netfilter: refuse insertion if chain has grown too large
- ncsi: add get MAC address command to get Intel i210 MAC address"
* tag 'net-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (76 commits)
ieee802154: Remove redundant initialization of variable ret
net: stmmac: fix MAC not working when system resume back with WoL active
net: phylink: add suspend/resume support
net: renesas: sh_eth: Fix freeing wrong tx descriptor
bonding: 3ad: pass parameter bond_params by reference
cxgb3: fix oops on module removal
can: c_can: fix null-ptr-deref on ioctl()
can: rcar_canfd: add __maybe_unused annotation to silence warning
net: wwan: iosm: Unify IO accessors used in the driver
net: wwan: iosm: Replace io.*64_lo_hi() with regular accessors
net: qcom/emac: Replace strlcpy with strscpy
ip6_gre: Revert "ip6_gre: add validation for csum_start"
net: hns3: make hclgevf_cmd_caps_bit_map0 and hclge_cmd_caps_bit_map0 static
selftests/bpf: Test XDP bonding nest and unwind
bonding: Fix negative jump label count on nested bonding
MAINTAINERS: add VM SOCKETS (AF_VSOCK) entry
stmmac: dwmac-loongson:Fix missing return value
iwlwifi: fix printk format warnings in uefi.c
net: create netdev->dev_addr assignment helpers
bnxt_en: Fix possible unintended driver initiated error recovery
...
This patch adds support for Telit LN920 0x1060 composition
0x1060: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: Carlo Lobrano <c.lobrano@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit LN920
0x1061 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the network devices connected to the system beyond
HSO_MAX_NET_DEVICES. add_net_device() in hso_create_net_device()
will be failed for the network_table is full. It will lead to
business failure which rely on network_table, for example,
hso_suspend() and hso_resume(). It will also lead to memory leak
because resource release process can not search the hso_device
object from network_table in hso_free_interface().
Add failure handler for add_net_device() in hso_create_net_device()
to solve the above problems.
Fixes: 72dc1c096c ("HSO: add option hso driver")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more cleanups
on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYS9/lg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylZNwCggKViEViSGqJFIafAZZjmI3Nt6tUAoMkRlhcd
n1MS3snS0Sq+7BdJs37M
=GyxP
-----END PGP SIGNATURE-----
Merge tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "big" set of tty/serial driver patches for 5.15-rc1
Nothing major in here at all, just some driver updates and more
cleanups on old tty apis and code that needed it that includes:
- tty.h cleanup of things that didn't belong in it
- other tty cleanups by Jiri
- driver cleanups
- rs485 support added to amba-pl011 driver
- dts updates
- stm32 serial driver updates
- other minor fixes and driver updates
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (83 commits)
tty: serial: uartlite: Use read_poll_timeout for a polling loop
tty: serial: uartlite: Use constants in early_uartlite_putc
tty: Fix data race between tiocsti() and flush_to_ldisc()
serial: vt8500: Use of_device_get_match_data
serial: tegra: Use of_device_get_match_data
serial: 8250_ingenic: Use of_device_get_match_data
tty: serial: linflexuart: Remove redundant check to simplify the code
tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
tty: serial: fsl_lpuart: enable two stop bits for lpuart32
tty: serial: fsl_lpuart: fix the wrong mapbase value
mxser: use semi-colons instead of commas
tty: moxa: use semi-colons instead of commas
tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
tty: replace in_irq() with in_hardirq()
serial: sh-sci: fix break handling for sysrq
serial: stm32: use devm_platform_get_and_ioremap_resource()
serial: stm32: use the defined variable to simplify code
Revert "arm pl011 serial: support multi-irq request"
tty: serial: samsung: Add Exynos850 SoC data
tty: serial: samsung: Fix driver data macros style
...
drivers/net/usb/asix_devices.c:757:60-65: WARNING: conversion to bool not needed here
Remove unneeded conversion to bool
Semantic patch information:
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unneeded.
Generated by: scripts/coccinelle/misc/boolconv.cocci
Fixes: 7a141e64cf ("net: usb: asix: ax88772: move embedded PHY detection as early as possible")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210825183538.13070-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Device removal can result in a large burst of driver warning messages
(20 - 30) sent to the kernel log. Most of these are register read/write
failures.
This change limits the rate at which these messages are emitted.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a device disconnect at roughly the same time as a
deferred PHY link reset there is a race condition that can result
in a kernel lock up due to a null pointer dereference in the
driver's deferred work handling routine lan78xx_delayedwork().
The following changes fix this problem.
Add new status flag EVENT_DEV_DISCONNECT to indicate when the
device has been removed and use it to prevent operations, such as
register access, that will fail once the device is removed.
Stop processing of deferred work items when the driver's USB
disconnect handler is invoked.
Disconnect the PHY only after the network device has been
unregistered and all delayed work has been cancelled.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the interface is given an IP address while the device is
suspended (as a result of an auto-suspend event) there is a race
between lan78xx_resume() and lan78xx_open() that can result in an
exception or failure to handle incoming packets. The following
changes fix this problem.
Introduce a mutex to serialise operations in the network interface
open and stop entry points with respect to the USB driver suspend
and resume entry points.
Move Tx and Rx data path start/stop to lan78xx_start() and
lan78xx_stop() respectively and flush the packet FIFOs before
starting the Tx and Rx data paths. This prevents the MAC and FIFOs
getting out of step and delivery of malformed packets to the network
stack.
Stop processing of received packets before disconnecting the
PHY from the MAC to prevent a kernel exception caused by handling
packets after the PHY device has been removed.
Refactor device auto-suspend code to make it consistent with the
the system suspend code and make the suspend handler easier to read.
Add new code to stop wake-on-lan packets or PHY events resuming the
host or device from suspend if the device has not been opened
(typically after an IP address is assigned).
This patch is dependent on changes to lan78xx_suspend() and
lan78xx_resume() introduced in the previous patch of this patch set.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC can get out of step with the internal packet FIFOs if the
system goes to sleep when the link is active, especially at high
data rates. This can result in partial frames in the packet FIFOs
that in result in malformed frames being delivered to the host.
This occurs because the driver does not enable/disable the internal
packet FIFOs in step with the corresponding MAC data path. The
following changes fix this problem.
Update code that enables/disables the MAC receiver and transmitter
to the more general Rx and Tx data path, where the data path in each
direction consists of both the MAC function (Tx or Rx) and the
corresponding packet FIFO.
In the receive path the packet FIFO must be enabled before the MAC
receiver but disabled after the MAC receiver.
In the transmit path the opposite is true: the packet FIFO must be
enabled after the MAC transmitter but disabled before the MAC
transmitter.
The packet FIFOs can be flushed safely once the corresponding data
path is stopped.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An exception is sometimes seen when the link speed is changed
from auto-negotiation to a fixed speed, or vice versa. The
exception occurs when the MAC is reset (due to the link speed
change) at the same time as the PHY state machine is accessing
a PHY register. The following changes fix this problem.
Rework the MAC reset to ensure there is no outstanding MDIO
register transaction before the reset and then wait until the
reset is complete before allowing any further MAC register access.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many places in the driver where the return code from a
function call is captured but without a subsequent test of the
return code and appropriate action taken.
This patch adds the missing return code tests and action. In most
cases the action is an early exit from the calling function.
The function lan78xx_set_suspend() was also updated to make it
consistent with lan78xx_suspend().
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the pause frame queue from the driver. It is initialised
but not actually used.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set threshold at which flow control is triggered to 3/4 full of
the internal Rx packet FIFO to prevent packet drops at high data
rates. The new setting reduces the number of dropped UDP frames
and TCP retransmit requests especially on less capable CPUs.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove kernel timer that is not used by the driver.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix white space and code style issues identified by checkpatch.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix crash on reboot on a system with ASIX AX88178 USB adapter attached
to it:
| asix 1-1.4:1.0 eth0: unregister 'asix' usb-ci_hdrc.0-1.4, ASIX AX88178 USB 2.0 Ethernet
| 8<--- cut here ---
| Unable to handle kernel NULL pointer dereference at virtual address 0000028c
| pgd = 5ec93aee
| [0000028c] *pgd=00000000
| Internal error: Oops: 5 [#1] PREEMPT SMP ARM
| Modules linked in:
| CPU: 1 PID: 1 Comm: systemd-shutdow Not tainted 5.14.0-rc1-20210811-1 #4
| Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
| PC is at phy_disconnect+0x8/0x48
| LR is at ax88772_unbind+0x14/0x20
| [<80650d04>] (phy_disconnect) from [<80741aa4>] (ax88772_unbind+0x14/0x20)
| [<80741aa4>] (ax88772_unbind) from [<8074e250>] (usbnet_disconnect+0x48/0xd8)
| [<8074e250>] (usbnet_disconnect) from [<807655e0>] (usb_unbind_interface+0x78/0x25c)
| [<807655e0>] (usb_unbind_interface) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)
| [<805ab26c>] (device_del) from [<807634a4>] (usb_disable_device+0xcc/0x178)
| [<807634a4>] (usb_disable_device) from [<8075a060>] (usb_disconnect+0xd8/0x238)
| [<8075a060>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<8075a02c>] (usb_disconnect+0xa4/0x238)
| [<8075a02c>] (usb_disconnect) from [<80af3520>] (usb_remove_hcd+0xa0/0x198)
| [<80af3520>] (usb_remove_hcd) from [<807902e0>] (host_stop+0x38/0xa8)
| [<807902e0>] (host_stop) from [<8078d9e4>] (ci_hdrc_remove+0x3c/0x118)
| [<8078d9e4>] (ci_hdrc_remove) from [<805b27ec>] (platform_remove+0x20/0x50)
| [<805b27ec>] (platform_remove) from [<805b03a0>] (__device_release_driver+0x154/0x20c)
| [<805b03a0>] (__device_release_driver) from [<805b0478>] (device_release_driver+0x20/0x2c)
| [<805b0478>] (device_release_driver) from [<805af944>] (bus_remove_device+0xcc/0xf8)
| [<805af944>] (bus_remove_device) from [<805ab26c>] (device_del+0x178/0x4b0)
For this adapter we call ax88178_bind() and ax88772_unbind(), which is
related to different chip version and different counter part *bind()
function.
Since this chip is currently not ported to the PHYLIB, we do not need to
call phy_disconnect() here. So, to fix this crash, we need to add
ax88178_unbind().
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Robin van der Gracht <robin@protonic.nl>
Tested-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some HW revisions need additional MAC configuration before the embedded PHY
can be enabled. If this is not done, we won't be able to get response
from the internal PHY.
This issue was detected on chipcode == AX_AX88772_CHIPCODE variant,
where ax88772_hw_reset() was executed with missing embd_phy flag.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9a ("net: usb: pegasus: Check the return value of get_geristers() and friends;")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum PLA bp number of RTL8153C is 16, not 8. That is, the
bp 0 ~ 15 are at 0xfc28 ~ 0xfc46, and the bp_en is at 0xfc48.
Fixes: 195aae321c ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register of USB_BP2_EN is 16 bits, so we should use
ocp_write_word(), not ocp_write_byte().
Fixes: 9370f2d05a ("support request_firmware for RTL8153")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported uninit-value in asix_mdio_read(). The problem was in
missing error handling. asix_read_cmd() should initialize passed stack
variable smsr, but it can fail in some cases. Then while condidition
checks possibly uninit smsr variable.
Since smsr is uninitialized stack variable, driver can misbehave,
because smsr will be random in case of asix_read_cmd() failure.
Fix it by adding error handling and just continue the loop instead of
checking uninit value.
Added helper function for checking Host_En bit, since wrong loop was used
in 4 functions and there is no need in copy-pasting code parts.
Cc: Robert Foss <robert.foss@collabora.com>
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Reported-by: syzbot+a631ec9e717fb0423053@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently phy_device state could be left in inconsistent state shown
by following alert message[1]. This is because phy_read_status could
be called concurrently from lan78xx_delayedwork, phy_state_machine and
__ethtool_get_link. Fix this by making sure that phy_device state is
updated atomically.
[1] lan78xx 1-1.1.1:1.0 eth0: No phy led trigger registered for speed(-1)
Signed-off-by: Ivan T. Ivanov <iivanov@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are now deemed redundant.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain call sites of get_geristers() did not do proper error handling. This
could be a problem as get_geristers() typically return the data via pointer to a
buffer. If an error occurred the code is carelessly manipulating the wrong data.
Signed-off-by: Petko Manolov <petkan@nucleusys.com>
Reviewed-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors. The safe replacement is strscpy().
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pegasus and rtl8150 drivers use SIOCDEVPRIVATE ioctls
to access their MII registers, in place of the normal
commands. This is broken for all compat ioctls today.
Change to ndo_siocdevprivate to fix it.
Cc: Petko Manolov <petkan@nucleusys.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
phonet has a single private ioctl that is broken in compat
mode on big-endian machines today because the data returned
from it is never copied back to user space.
Move it over to the ndo_siocdevprivate callback, which also
fixes the compat issue.
Cc: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rémi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68e (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
asix_get_phyid() is used for two reasons here. To print debug message
with the PHY ID and to wait until the PHY is powered up.
After migrating to the phylib, we can read PHYID from sysfs. If polling
for the PHY is really needed, then we will need to handle it in the
phylib as well.
This change was tested with:
- ax88772a + internal PHY
- ax88772b + external PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two invocation sites of hso_free_net_device. After
refactoring hso_create_net_device, this parameter is useless.
Remove the bailout in the hso_free_net_device and change the invocation
sites of this function.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
[1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com
Fixes: 5fcfb6d0bf ("hso: fix bailout in error case of probe")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current error handling code of hso_create_net_device is
hso_free_net_device, no matter which errors lead to. For example,
WARNING in hso_free_net_device [1].
Fix this by refactoring the error handling code of
hso_create_net_device by handling different errors by different code.
[1] https://syzkaller.appspot.com/bug?id=66eff8d49af1b28370ad342787413e35bbe76efe
Reported-by: syzbot+44d53c7255bb1aea22d2@syzkaller.appspotmail.com
Fixes: 5fcfb6d0bf ("hso: fix bailout in error case of probe")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8152 driver sets up the MAC address at reset-resume, while
rtl8152_set_mac_address() has the temporary autopm get/put. This may
lead to a deadlock as the PM lock has been already taken for the
execution of the runtime PM callback.
This patch adds the workaround to avoid the superfluous autpm when
called from rtl8152_reset_resume().
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8152_close() takes the refcount via usb_autopm_get_interface() but
it doesn't release when RTL8152_UNPLUG test hits. This may lead to
the imbalance of PM refcount. This patch addresses it.
Link: https://bugzilla.suse.com/show_bug.cgi?id=1186194
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets
in subflow receive buffers longer than necessary, delaying
MPTCP-level ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack: do not renew entry stuck in tcp SYN_SENT state
- netfilter: conntrack: do not mark RST in the reply direction coming
after SYN packet for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison
-----BEGIN PGP SIGNATURE-----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=QFnb
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski.
"Including fixes from bpf and netfilter.
Current release - regressions:
- sock: fix parameter order in sock_setsockopt()
Current release - new code bugs:
- netfilter: nft_last:
- fix incorrect arithmetic when restoring last used
- honor NFTA_LAST_SET on restoration
Previous releases - regressions:
- udp: properly flush normal packet at GRO time
- sfc: ensure correct number of XDP queues; don't allow enabling the
feature if there isn't sufficient resources to Tx from any CPU
- dsa: sja1105: fix address learning getting disabled on the CPU port
- mptcp: addresses a rmem accounting issue that could keep packets in
subflow receive buffers longer than necessary, delaying MPTCP-level
ACKs
- ip_tunnel: fix mtu calculation for ETHER tunnel devices
- do not reuse skbs allocated from skbuff_fclone_cache in the napi
skb cache, we'd try to return them to the wrong slab cache
- tcp: consistently disable header prediction for mptcp
Previous releases - always broken:
- bpf: fix subprog poke descriptor tracking use-after-free
- ipv6:
- allocate enough headroom in ip6_finish_output2() in case
iptables TEE is used
- tcp: drop silly ICMPv6 packet too big messages to avoid
expensive and pointless lookups (which may serve as a DDOS
vector)
- make sure fwmark is copied in SYNACK packets
- fix 'disable_policy' for forwarded packets (align with IPv4)
- netfilter: conntrack:
- do not renew entry stuck in tcp SYN_SENT state
- do not mark RST in the reply direction coming after SYN packet
for an out-of-sync entry
- mptcp: cleanly handle error conditions with MP_JOIN and syncookies
- mptcp: fix double free when rejecting a join due to port mismatch
- validate lwtstate->data before returning from skb_tunnel_info()
- tcp: call sk_wmem_schedule before sk_mem_charge in zerocopy path
- mt76: mt7921: continue to probe driver when fw already downloaded
- bonding: fix multiple issues with offloading IPsec to (thru?) bond
- stmmac: ptp: fix issues around Qbv support and setting time back
- bcmgenet: always clear wake-up based on energy detection
Misc:
- sctp: move 198 addresses from unusable to private scope
- ptp: support virtual clocks and timestamping
- openvswitch: optimize operation for key comparison"
* tag 'net-5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (158 commits)
net: dsa: properly check for the bridge_leave methods in dsa_switch_bridge_leave()
sfc: add logs explaining XDP_TX/REDIRECT is not available
sfc: ensure correct number of XDP queues
sfc: fix lack of XDP TX queues - error XDP TX failed (-22)
net: fddi: fix UAF in fza_probe
net: dsa: sja1105: fix address learning getting disabled on the CPU port
net: ocelot: fix switchdev objects synced for wrong netdev with LAG offload
net: Use nlmsg_unicast() instead of netlink_unicast()
octeontx2-pf: Fix uninitialized boolean variable pps
ipv6: allocate enough headroom in ip6_finish_output2()
net: hdlc: rename 'mod_init' & 'mod_exit' functions to be module-specific
net: bridge: multicast: fix MRD advertisement router port marking race
net: bridge: multicast: fix PIM hello router port marking race
net: phy: marvell10g: fix differentiation of 88X3310 from 88X3340
dsa: fix for_each_child.cocci warnings
virtio_net: check virtqueue_add_sgs() return value
mptcp: properly account bulk freed memory
selftests: mptcp: fix case multiple subflows limited by server
mptcp: avoid processing packet if a subflow reset
mptcp: fix syncookie process if mptcp can not_accept new subflow
...
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
After probe/bind sequence is the PHY in active state, even if interface
is stopped. As result, on some systems like Samsung Exynos5250 SoC based Arndale
board, the ASIX PHY will be able to negotiate the link but fail to
transmit the data.
To handle it, suspend the PHY on probe.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the netdev_dbg content from int to char * in usbnet_defer_kevent(),
this looks more readable.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Store the information of the pipes to avoid calling usb_rcvctrlpipe(),
usb_sndctrlpipe(), usb_rcvbulkpipe(), usb_sndbulkpipe(), and
usb_rcvintpipe() frequently.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.
fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet.
Fixes: 9f722c0978 ("usbnet: CDC EEM support (v5)")
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 46a8b29c63 ("net: usb: fix memory leak in smsc75xx_bind")
fails to clean up the work scheduled in smsc75xx_reset->
smsc75xx_set_multicast, which leads to use-after-free if the work is
scheduled to start after the deallocation. In addition, this patch
also removes a dangling pointer - dev->data[0].
This patch calls cancel_work_sync to cancel the scheduled work and set
the dangling pointer to NULL.
Fixes: 46a8b29c63 ("net: usb: fix memory leak in smsc75xx_bind")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the QMI_WWAN_FLAG_PASS_THROUGH is set, netif_rx() is called from
qmi_wwan_rx_fixup(). When the call to netif_rx() is successful (which is
most of the time), usbnet_skb_return() is called (from rx_process()).
usbnet_skb_return() will then call netif_rx() a second time for the same
skb.
Simplify the code and avoid the redundant netif_rx() call by changing
qmi_wwan_rx_fixup() to always return 1 when QMI_WWAN_FLAG_PASS_THROUGH
is set. We then leave it up to the existing infrastructure to call
netif_rx().
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is meant to make the host side cdc_ncm interface consistently
named just like the older CDC protocols: cdc_ether & cdc_ecm
(and even rndis_host), which all use 'FLAG_ETHER | FLAG_POINTTOPOINT'.
include/linux/usb/usbnet.h:
#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */
#define FLAG_WLAN 0x0080 /* use "wlan%d" names */
#define FLAG_WWAN 0x0400 /* use "wwan%d" names */
#define FLAG_POINTTOPOINT 0x1000 /* possibly use "usb%d" names */
drivers/net/usb/usbnet.c @ line 1711:
strcpy (net->name, "usb%d");
...
// heuristic: "usb%d" for links we know are two-host,
// else "eth%d" when there's reasonable doubt. userspace
// can rename the link if it knows better.
if ((dev->driver_info->flags & FLAG_ETHER) != 0 &&
((dev->driver_info->flags & FLAG_POINTTOPOINT) == 0 ||
(net->dev_addr [0] & 0x02) == 0))
strcpy (net->name, "eth%d");
/* WLAN devices should always be named "wlan%d" */
if ((dev->driver_info->flags & FLAG_WLAN) != 0)
strcpy(net->name, "wlan%d");
/* WWAN devices should always be named "wwan%d" */
if ((dev->driver_info->flags & FLAG_WWAN) != 0)
strcpy(net->name, "wwan%d");
So by using ETHER | POINTTOPOINT the interface naming is
either usb%d or eth%d based on the global uniqueness of the
mac address of the device.
Without this 2.5gbps ethernet dongles which all seem to use the cdc_ncm
driver end up being called usb%d instead of eth%d even though they're
definitely not two-host. (All 1gbps & 5gbps ethernet usb dongles I've
tested don't hit this problem due to use of different drivers, primarily
r8152 and aqc111)
Fixes tag is based purely on git blame, and is really just here to make
sure this hits LTS branches newer than v4.5.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 4d06dd537f ("cdc_ncm: do not call usbnet_link_change from cdc_ncm_bind")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take over PHY power management, otherwise PHY framework will try to
access ASIX MDIO bus before MAC resume was completed.
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison of the u16 priv->phy_addr < 0 is always false because
phy_addr is unsigned. Fix this by assigning the return from the call
to function asix_read_phy_addr to int ret and using this for the
less than zero error check comparison.
Fixes: 7e88b11a86 ("net: usb: asix: refactor asix_read_phy_addr() and handle errors on return")
Addresses-Coverity: ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison of the u16 priv->phy_addr < 0 is always false because
phy_addr is unsigned. Fix this by assigning the return from the call
to function asix_read_phy_addr to int ret and using this for the
less than zero error check comparison.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: e532a096be ("net: usb: asix: ax88772: add phylib support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unbind() is the proper place to disconnect PHY, but it will fail if
netdev is already unregistered.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This usb devices can be removed at any time, so we need to forward
correct error value if device was detached.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With working phylib support we are able now to use generic selftests.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to use ax88772 with external PHYs and use advantage of
existing PHY drivers, we need to port at least ax88772 part of asix
driver to the phylib framework.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for build-in x88772A/C PHYs
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor asix_read_phy_addr() to return usable error value directly and
make sure all callers handle this error.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make resource management easier, use devm_kzalloc().
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support get_pauseparam and set_pauseparam of ethtool_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported memory leak in smsc75xx_bind().
The problem was is non-freed memory in case of
errors after memory allocation.
backtrace:
[<ffffffff84245b62>] kmalloc include/linux/slab.h:556 [inline]
[<ffffffff84245b62>] kzalloc include/linux/slab.h:686 [inline]
[<ffffffff84245b62>] smsc75xx_bind+0x7a/0x334 drivers/net/usb/smsc75xx.c:1460
[<ffffffff82b5b2e6>] usbnet_probe+0x3b6/0xc30 drivers/net/usb/usbnet.c:1728
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Cc: stable@kernel.vger.org
Reported-and-tested-by: syzbot+b558506ba8165425fee2@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Fix the tiocmset and rfkill requests which erroneously used
usb_rcvctrlpipe().
Fixes: 72dc1c096c ("HSO: add option hso driver")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify some fields of the USB descriptor to make sure the driver
could be used by the device.
Besides, remove the check of endpoint number in rtl8152_probe().
usb_find_common_endpoints() includes it.
BugLink: https://syzkaller.appspot.com/bug?id=912c9c373656996801b4de61f1e3cb326fe940aa
Reported-by: syzbot+95afd23673f5dd295c57@syzkaller.appspotmail.com
Fixes: c2198943e3 ("r8152: search the configuration of vendor mode")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RW helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEVICE_ATTR_RO helper instead of plain DEVICE_ATTR,
which makes the code a bit shorter and easier to read.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few leading spaces before tabs and remove it by running
the following commard:
$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski
Davide Tronchin
Eric Dumazet
Foster Snowhill
Georgi Valkov
Wes Huang
Sebastian Krzyszkowiak
Tudor Ambarus
Hayes Wang
Douglas Anderson
Grant Grundler
Tom Rix
Szymon Heidrich
Enrico Sau
Yuiko Oshino
David S. Miller
Miko Larsson
Alan Stern
Andre Przywara
Bjørn Mork
Leesoo Ahn
Hui Wang
Linus Torvalds
Steven Rostedt (Google)
Oleksij Rempel
Santiago Ruano Rincón
Alexandru Tachici
Russell King (Oracle)
Christophe JAILLET
Denis Kirjanov
Andrew Gaul
Frank Wunderlich
Peilin Ye
Greg Kroah-Hartman
Paolo Abeni
jerry.meng
André Apitzsch
Sven van Ashbrook
Wolfram Sang
Ilpo Järvinen
Jean-Francois Le Fillatre
Slark Xiao
Jose Alonso
Hector Martin
Maciej Żenczykowski
Xie Shaowen
Justin Chen
Dominik Czerwik
Oliver Neukum
Zhengchao Shao
Lukas Wunner
Li kunyu
Parthiban Veerasooran
Carlo Lobrano
David Ober
Ethan Yang
Vincent Mailhol
Yunbo Yu
Lech Perczak
Daniele Palmas
Marcin Kozlowski
Wang Qing
Greg Jesionowski
Ingo Molnar
Fabio Estevam
Sebastian Andrzej Siewior
Gustavo A. R. Silva
Jann Horn
Pavel Skripkin
Georgi Valkov
Colin Ian King
Markus Reichl
Kyoungkyu Park
Pawel Dembicki
Aaron Ma
Thomas Toye
Matthias-Christian Ott
Lee Jones
Sven Schuchmann
Jiapeng Chong
Martyn Welch
Hao Chen
John Efstathiades
Jacky Chou
Wang Hai
Johan Hovold
Vegard Nossum
Aaro Koskinen
Ziyang Xuan
kernel test robot
Yufeng Mo
Petko Manolov
Ivan T. Ivanov
Petko Manolov
Len Baker
Arnd Bergmann
Jiri Slaby
Dongliang Mu
Takashi Iwai
Yajun Deng
Linyu Yuan
Kees Cook
Kristian Evensen
Colin Ian King
Zheng Yongjun
YueHaibing
Hui Tang