pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704075434.3220506-1-sakari.ailus@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI controller requires vender specific handling when
an SDIO irq occurs. So, add .sdio_irq() to the tmio core.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250610072545.2001435-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_can_* functions sometimes relate to the card and sometimes to the host.
Make it obvious by renaming this function to include 'host'.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250401095847.29271-12-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_can_* functions sometimes relate to the card and sometimes to the host.
Make it obvious by renaming this function to include 'host'.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250401095847.29271-11-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_RSP_R1_NO_CRC type of response is not being used by the mmc core
for any commands. Let's therefore drop it, together with the corresponding
code in the host drivers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # for TMIO
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Message-ID: <20241125132311.23939-1-ulf.hansson@linaro.org>
- Add support for ROHM BD96801 Power Management IC
- Add support for Cirrus Logic CS40L50 Haptic Driver with Waveform Memory
- Add support for Marvell 88PM886 Power Management IC
- New Device Support
- Add support for Keyboard Backlight to ChromeOS Embedded Controller
- Add support for LEDs to ChromeOS Embedded Controller
- Add support for Charge Control to ChromeOS Embedded Controller
- Add support for the HW Monitoring Service to ChromeOS Embedded Controller
- Add support for AUXADCs to MediaTek MT635{7,8,9} Power Management ICs
- New Functionality
- Allow Syscon consumers to supply their own Regmaps on registration
- Fix-ups
- Constify/staticise applicable data structures
- Remove superfluous/duplicated/unused sections
- Device Tree binding adaptions/conversions/creation
- Trivial; spelling, whitespace, coding-style adaptions
- Utilise centrally provided helpers and macros to aid simplicity/duplication
- Drop i2c_device_id::driver_data where the value is unused
- Replace ACPI/DT firmware helpers with agnostic variants
- Move over to GPIOD (descriptor-based) APIs
- Annotate a bunch of __counted_by() cases
- Straighten out some includes
- Bug Fixes
- Ensure potentially asserted recent lines are deasserted during initialisation
- Avoid "<module>.ko is added to multiple modules" warnings
- Supply a bunch of MODULE_DESCRIPTIONs to silence modpost warnings
- Fix Wvoid-pointer-to-enum-cast warnings
-----BEGIN PGP SIGNATURE-----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=DSjk
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- ROHM BD96801 Power Management IC
- Cirrus Logic CS40L50 Haptic Driver with Waveform Memory
- Marvell 88PM886 Power Management IC
New Device Support:
- Keyboard Backlight to ChromeOS Embedded Controller
- LEDs to ChromeOS Embedded Controller
- Charge Control to ChromeOS Embedded Controller
- HW Monitoring Service to ChromeOS Embedded Controller
- AUXADCs to MediaTek MT635{7,8,9} Power Management ICs
New Functionality:
- Allow Syscon consumers to supply their own Regmaps on registration
Fix-ups:
- Constify/staticise applicable data structures
- Remove superfluous/duplicated/unused sections
- Device Tree binding adaptions/conversions/creation
- Trivial; spelling, whitespace, coding-style adaptions
- Utilise centrally provided helpers and macros to aid
simplicity/duplication
- Drop i2c_device_id::driver_data where the value is unused
- Replace ACPI/DT firmware helpers with agnostic variants
- Move over to GPIOD (descriptor-based) APIs
- Annotate a bunch of __counted_by() cases
- Straighten out some includes
Bug Fixes:
- Ensure potentially asserted recent lines are deasserted during
initialisation
- Avoid "<module>.ko is added to multiple modules" warnings
- Supply a bunch of MODULE_DESCRIPTIONs to silence modpost warnings
- Fix Wvoid-pointer-to-enum-cast warnings"
* tag 'mfd-next-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (87 commits)
mfd: timberdale: Attach device properties to TSC2007 board info
mfd: tmio: Move header to platform_data
mfd: tmio: Sanitize comments
mfd: tmio: Update include files
mmc: tmio/sdhi: Fix includes
mfd: tmio: Remove obsolete io accessors
mfd: tmio: Remove obsolete platform_data
watchdog: bd96801_wdt: Add missing include for FIELD_*()
dt-bindings: mfd: syscon: Add APM poweroff mailbox
dt-bindings: mfd: syscon: Split and enforce documenting MFD children
dt-bindings: mfd: rk817: Merge support for RK809
dt-bindings: mfd: rk817: Fixup clocks and reference dai-common
dt-bindings: mfd: syscon: Add TI's opp table compatible
mfd: omap-usb-tll: Use struct_size to allocate tll
dt-bindings: mfd: Explain lack of child dependency in simple-mfd
dt-bindings: mfd: Dual licensing for st,stpmic1 bindings
mfd: omap-usb-tll: Annotate struct usbtll_omap with __counted_by
mfd: tps6594-core: Remove unneeded semicolon in tps6594_check_crc_mode()
mfd: lm3533: Move to new GPIO descriptor-based APIs
mfd: tps65912: Use devm helper functions to simplify probe
...
All the MFD components are gone from the header meanwhile. Only the MMC
relevant data is left which makes it a platform_data for the MMC
controller. Move the header to the now fitting directory.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240213220221.2380-14-wsa+renesas@sang-engineering.com
Signed-off-by: Lee Jones <lee@kernel.org>
The only generic interface to execute asynchronously in the BH context is
tasklet; however, it's marked deprecated and has some design flaws. To
replace tasklets, BH workqueue support was recently added. A BH workqueue
behaves similarly to regular workqueues except that the queued work items
are executed in the BH context.
This patch converts the SDHI driver from tasklet to BH workqueue.
Based on the work done by Tejun Heo <tj@kernel.org>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
[wsa: fixed build faliures, corrected whitespace issues]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20240626085015.32171-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit ca78476e48 ("mfd: Remove toshiba tmio drivers") removed the
last users of the .set_pwr() callback in the tmio_mmc_data structure.
Remove the callback, and all related infrastructure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/fbbc13ddd19df2c40933ffa3b82fb14841bf1d4c.1718897545.git.geert+renesas@glider.be
make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/host/of_mmc_spi.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/host/tmio_mmc_core.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/host/renesas_sdhi_core.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/core/mmc_core.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/core/pwrseq_simple.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/core/pwrseq_sd8787.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/core/pwrseq_emmc.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/mmc/core/sdio_uart.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # for TMIO and SDHI
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20240611-md-drivers-mmc-v2-1-2ef2cbcdc061@quicinc.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the to-be-fixed commit, the reset_work handler cleared 'host->mrq'
outside of the spinlock protected critical section. That leaves a small
race window during execution of 'tmio_mmc_reset()' where the done_work
handler could grab a pointer to the now invalid 'host->mrq'. Both would
use it to call mmc_request_done() causing problems (see link below).
However, 'host->mrq' cannot simply be cleared earlier inside the
critical section. That would allow new mrqs to come in asynchronously
while the actual reset of the controller still needs to be done. So,
like 'tmio_mmc_set_ios()', an ERR_PTR is used to prevent new mrqs from
coming in but still avoiding concurrency between work handlers.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/all/20240220061356.3001761-1-dirk.behme@de.bosch.com/
Fixes: df3ef2d3c9 ("mmc: protect the tmio_mmc driver against a theoretical race")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: stable@vger.kernel.org # 3.0+
Link: https://lore.kernel.org/r/20240305104423.3177-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to to of_property_read_bool().
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230310144715.1543836-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After a8402aed8ca5 ("mmc: tmio_mmc_core: Remove
local_irq_{save,restore}() around k[un]map_atomic()") and ac91578a6812
("mmc: tmio_mmc_core: Replace kmap_atomic() with kmap_local_page()"),
the helpers contain just a single call. Putting it directly in the code
makes it actually more readable. More so, because we now avoid the
'offset' calculation when mapping/unmapping and just use it when we need
it in the copy routines.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221102125430.28466-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't want to rely only on the access_end irq in the future, so
implement a callback for dma irqs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221006190452.5316-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A long time ago the kmap_atomic API required a slot to be provided which
risked the possibility that other code might use the same slot at the
same time. Disabling interrupts prevented the possibility of an interrupt
handler doing that. However, that went away with
commit 3e4d3af501 ("mm: stack based kmap_atomic()").
When the second argument to kmap_atomic was removed by commit 482fce997e
("mmc: remove the second argument of k[un]map_atomic()"),
local_irq_{save,restore}() should have been removed also.
Remove it now.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221005101951.3165-12-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we reset because of an error, we need to preserve values for the
clock frequency. Otherwise, glitches may be seen on the bus.
To achieve that, we introduce a 'preserve' parameter to the reset
function and the IP core specific reset callbacks to handle everything
accordingly.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220625131722.1397-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Refactor the code so that card detect irqs are always reenabled after a
reset. This avoids doing it manually all over the code or forgetting to
do this in the future.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
[wsa: added a comment when 'native_hotplug' has to be set]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211103122646.64422-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The reset callback may clear the internal card detect interrupts, so
make sure to reenable them if needed.
Fixes: b4d86f37ea ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211028195149.8003-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, only SDHI on R-Car Gen2+ reinitializes the irq register
during reset but it should be done on all instances. We can move it from
the SDHI driver to the TMIO core, because we now have the
'sd_irq_mask_all' variable which carries the proper value to use. That
also means we can remove the initialization from tmio_mmc_probe()
because it calls tmio_mmc_reset(), too. We only move that
tmio_mmc_reset() call there a little to ensure 'sd_irq_mask_all' is
properly set.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210413083137.11171-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After reset, we manually flagged retune in runtime resume, but missed it
in the workqueue. To fix that and avoid the problem in the future, let's
flag retune in the reset handler directly whenever a card is present.
Reported-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Resetting the IP core will lose the bus width information and not all
code paths recover it. So, make sure the latest bus width gets restored
in the reset routine. For that, tmio_mmc_set_bus_width() is moved, but
not modified.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210316085717.7276-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will soon allow resetting the whole IP core via a reset controller.
For this case, DMA must be terminated before the actual reset. For the
other cases, it is probably better, too.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210317091622.31890-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHI Gen2+ has a different value for TMIO_MASK_ALL, so add a member to
support that. If the member is not used, the previous default value is
applied.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210223100830.25125-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RPM handling has been improved twice since this comment, and also SCC
handling has been improved a lot. All the testing we did (Geert's and
Niklas' and Wolfram's board farms) with the workaround removed did not
lead to problems, so it is time to get rid of it to the best of our
knowledge.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210218110224.6910-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the datasheet, this controller needs retune when
cmd or data timeout happens. So, add a condition into .check_retune().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, busy timeout is not checked for data transfer command. But,
if the temperature condition changes, the data cannot be acquired
correctly and timeout may occur. Also, we could reproduce an issue by
using mmc_test driver (e.g. "Correct xfer_size at write (start
failure)"). Therefore, this adds timeout error check.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rework commit message.]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: rebase, add commit description]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer SDHI variants can 'wait while busy' longer than the generic TMIO.
Provide a hook to get the maximum cycle count to wait for. If the hook
is not populated, fall back to a generic version which works well with
all older TMIO/SDHI variants.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set max_busy_timeouts for variants known to support the TOPxx bits in
the SD_OPTION register. The timeout mechanism was running in the
background but not yet properly handled in the driver. So, let the MMC
core know when to not use R1B to avoid unhandled timeouts.
My datasheets for older variants (tmio_mmc.c) suggest that they support
it, too. However, actual bit descriptions are lacking, so I chose an
opt-in approach.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Further testing of error cases revealed that downgrade is not enough, so
we need to reset the SCC which is done by calling the custom reset
function. This reset function can distinguish between the various SDHI
variants, so protecting the call with MIN_RCAR2 is enough here.
Fixes: 24ce2d7b8b ("mmc: tmio: bring tuning HW to a sane state with MMC_POWER_OFF")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125204953.3344-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If some errors are detected at the same time as the access end
interrupt, the access end interrupt was not cleared. Especially with
DMA, because then the access end interrupt was never enabled and, thus,
never cleared. Clear the interrupt register always when a command error
occurs.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rebase to v5.4]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebase and extension of the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201117131337.35307-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When powering off a card, we need to disable the tuning HW (like SCC for
the Renesas SDHI) to get to a sane state and allow for re-tuning new
cards. This was hidden before because we wrongly did that in hw_reset()
before which was an unintended use of hw_reset(). Now that we corrected
the use of hw_reset() meanwhile, we revealed this shortcoming and need
to fix it properly by explicitly calling the downgrade callback.
Fixes: 6e7d4de108 ("mmc: renesas_sdhi: move wrong 'hw_reset' to 'reset'")
Suggested-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Reviewed-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When applying a revert, the assumption that DMA only needs to be cleared
in specific cases was wrong. We want to reset the DMA controller every
time the rest of the HW gets reset, too.
Fixes: 34e3211e54 ("Revert "mmc: tmio: fix reset operation"")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After all the previous refactorization, we can now populate mmc_ops
directly and don't need a layer inbetween. The NULL-pointer check and
the error printout are already done by the MMC core.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-7-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHI needs to reset the SCC only, not the whole IP core. So, if tuning
fails, don't handle specifics in the generic TMIO core, but in the
specific drivers. For SDHI, we need to move around the reset routine a
bit. It is not modified.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some TMIO variants need specific actions in their reset routine, but
they are all based on a generic reset routine. So, the optional 'reset'
callback will now only take care of the additional stuff and we will
have a generic function around it. Less code, easier to maintain, and
much more readable. Code in tmio_mmc.c is untested but in my TC6387XB
datasheet the SDIO part is reset independently from the SD part, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After Yamada-san's refactorization introducing 'tmio_mmc_host_alloc', we
can populate mmc_ops directly and don't need a layer inbetween.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit a87852c6b8. It did fix
the issue, but was building on top of already wrong assumptions. The
driver missed that 'hw_reset' was only for resetting remote HW (card)
and not for the IP core. Since we fixed that in a previous patch, we can
now remove this patch to make it clear that 'reset' is for resetting the
IP core only. Also, cancelling DMA will only be called when actually
needed again. It will also allow for further cleanups and better
readability. Note that in addition to the revert, the call in
'tmio_mmc_execute_tuning' will be converted, too, to maintain the
current behaviour.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200820132538.24758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Related drivers like renesas_sdhi_internal_dmac are possible
to lack dma unmaping in error cases (for example response timeout).
Since tmio_mmc_finish_request() will be always called in any case,
to fix the issue, add end operation into struct tmio_mmc_dma_ops and
call the operation in tmio_mmc_finish_request() to call dma_ummap API
by the related drivers correctly.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1590044466-28372-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the tmio device is attached to a genpd (PM domain), that genpd may have
->start|stop() callback assigned to it. To make sure the device is
accessible during ->probe(), genpd's ->start() callback must be invoked,
which is currently managed by tmio_mmc_host_probe(). However, it's likely
that may be too late for some cases, as registers may be read and written
way before that point.
To fix the behaviour, let's move the call to dev_pm_domain_start() from
tmio_mmc_host_probe() into those clients that needs it. From discussions at
linux-mmc mailing list, it turned out that it should be sufficient to do
this for the SDHI renesas variants, hence the call is move to
renesas_sdhi_probe().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200519152445.6922-1-ulf.hansson@linaro.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Before calling tmio_mmc_host_probe(), the caller is required to enable
clocks for its device, as to make it accessible when reading/writing
registers during probe.
Therefore, the responsibility to disable these clocks, in the error path of
->probe() and during ->remove(), is better managed outside
tmio_mmc_host_remove(). As a matter of fact, callers of
tmio_mmc_host_remove() already expects this to be the behaviour.
However, there's a problem with tmio_mmc_host_remove() when the Kconfig
option, CONFIG_PM, is set. More precisely, tmio_mmc_host_remove() may then
disable the clock via runtime PM, which leads to clock enable/disable
imbalance problems, when the caller of tmio_mmc_host_remove() also tries to
disable the same clocks.
To solve the problem, let's make sure tmio_mmc_host_remove() leaves the
device with clocks enabled, but also make sure to disable the IRQs, as we
normally do at ->runtime_suspend().
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200519152434.6867-1-ulf.hansson@linaro.org
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
The MMC_CAP_ERASE bit is no longer used by the mmc core as erase, discard
and trim operations are now always supported. Therefore, drop the bit and
move all mmc hosts away from using it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Link: https://lore.kernel.org/r/20200508112902.23575-1-ulf.hansson@linaro.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
After various refactoring, we can populate the mmc_ops callbacks
directly and don't need to have wrappers for them anymore.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-7-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, select_tuning() is called after RPM resume. But
select_tuning() needs some additional function calls to work correctly.
Instead of reimplementing the whole postprocessing, just enforce
retuning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
check_scc_error() is too Renesas specific. Let's just call it
check_retune() to make it also easier understandable what it does.
Only a rename, no functional change.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200129203709.30493-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sakari Ailus
Yoshihiro Shimoda
Binbin Zhou
Wolfram Sang
Ulf Hansson
Lad Prabhakar
Linus Torvalds
Allen Pais
Geert Uytterhoeven
Jeff Johnson
Rob Herring
Adrian Hunter
Biju Das
Takeshi Saito
Masaharu Hayakawa