The byt_rt5640_hp_elitepad_1000g2_jack?_check functions are only
used inside bytcr_rt5640.c, mark them as static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210823110432.64860-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Contrary to what is said in board's file, topology targeting
kbl_da7219_max98373 expects format 16b, not 24/32b. Partially revert
changes added in 'ASoC: Intel: Boards: Add Maxim98373 support' to bring
old behavior back, aligning with topology expectations.
Fixes: 716d53cc78 ("ASoC: Intel: Boards: Add Maxim98373 support")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Tested-by: Lukasz Majczak <lma@semihalf.com>
Link: https://lore.kernel.org/r/20210818075742.1515155-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Elitepad 1000 G2 tablet has 2 headset jacks:
1. on the dock which uses the output of the codecs built-in HP-amp +
the standard IN2 input which is always used with the headset-jack.
2. on the tablet itself, this uses the line-out of the codec + an external
HP-amp, which gets enabled by the ALC5642 codec's GPIO1 pin; and IN1 for
the headset-mic.
The codec's GPIO1 is also its only IRQ output pin, so this means that
the codec's IRQ cannot be used on this tablet. Instead the jack-detect
is connected directly to GPIOs on the main SoC. The dock has a helper
chip which also detects if a headset-mic is present or not, so there
are 2 GPIOs for the jack-detect status of the dock. The tablet jack
uses a single GPIO which indicates if a jack is present or not.
Differentiating between headphones vs a headset on the tablet jack
is done by using the usual mic-bias over-current-detection mechanism.
Add support for this unique setup, this support gets enabled on this
tablet through a new BYT_RT5640_JD_HP_ELITEP_1000G2 quirk.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213415
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210819190543.784415-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to be able to do jack-detection reporting for the
mic contact on the 2nd jack found on some devices, the
DAPM topology needs to have a separate DAPM pin/input for that
microphone, instead of re-using the "Internal Mic" pin which is
normally used together with the IN1P input of the codec.
Using the "Internal Mic" dapm-pin-switch for this in a snd_soc_jack_pin to
report hotplug events causes the "Internal Mic" pin to get deactivated
when unplugging a headset from the 2nd jack, thus turning off the actual
Internal Mic (typically a pair of digital mics on devices with 2 jacks).
Fixes: 79c1123bac ("ASoC: Intel: bytcr_rt5640: Add support for a second headset mic input")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210819190543.784415-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use "cfg-lineout:2" in the components string on boards with a lineout
instead of "cfg-lineout:1", this better mirrors the speaker part of
the components string where we use "cfg-spk:1" for devices with a single
speaker and "cfg-spk:2" for stereo speakers.
The lineout is stereo by default, so using ":2" makes more sense, this
way we keep ":1" reserved in case we ever encounter a device with
a mono lineout.
We can make this change without breaking userspace because no kernel
has shipped with "cfg-lineout:1" in the component-string yet; and there
also are no userspace bits (UCM profiles) checking for this yet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210816114722.107363-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function device_add_properties() is going to be removed.
Replacing it with software node API equivalents.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Co-developed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Prepare the transition to the software node API by removing device
properties in the probe error handling and .remove callback.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The function device_add_properties() is going to be removed.
Replacing it with software node API equivalents.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the example of Intel Atom drivers and keep a reference to the
headset codec until the properties are removed.
There is no guarantee that the module for the codec driver is loaded
before the machine driver probe, the use of the deferred probe
mechanism is required.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we want to handle a context in init/exit function, we have to pass
the card information. This will be necessary to better deal with
device properties in the follow-up commits.
No functional change other than prototype update.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have an existing 'adev' handle from which we can find the codec
device, no need for an I2C bus search.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
acpi_dev_get_first_match_dev() searches for an acpi_handle
instantiated by the ACPI table scanning done early during boot.
Two of three machine drivers using this search don't deal with errors
and the one which does (bytcr_rt5651) returns -ENODEV, which doesn't
make sense here: an alternate driver will not be probed.
Add consistent error handling and report -ENXIO.
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In current ACPI-based devices, the DSDT does not include any of the
properties required by the codec driver. This is not an ACPI
limitation proper since the _DSD method could be used, as done for
Camera and SoundWire in newer platforms. For legacy devices, there is
unfortunately no other option than using a work-around: we add
properties to the codec device from the machine driver.
To avoid any issues with the codec driver being unbound, we need to
keep a reference to the codec device until the card is removed.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Co-developed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210813151116.23931-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No need to initialize a variable if the next line overwrites the value.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210802152151.15832-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default SOF topology enables SSP capture and DMICs, even though
both of these hardware capabilities are not always available in
hardware (specific versions of HiFiberry and DMIC kit needed).
For the SSP capture, this leads to annoying "SP5-Codec: ASoC: no
backend capture" and "streamSSP5-Codec: ASoC: no users capture at
close - state 0" errors.
Update the quirks to match what the topology needs, which also allows
for the ability to remove SSP capture and DMIC support.
BugLink: https://github.com/thesofproject/linux/issues/3061
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210802152151.15832-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DMI product name is used to support system variants based on
adl_mx98373_rt5682 in current implementation. Replace this DMI search with
DMI_OEM_STRING and coreboot(BIOS used in these systems) is
setting the needed DMI_OEM_STRING field to uniquely identify these
systems.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: jairaj arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802152151.15832-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This device has the same audio subsystem as the 0A5E skew (RT711
headset codec, 2 RT1308 amps and RT715 for mic capture)
BugLink: https://github.com/thesofproject/linux/issues/3057
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: FRED OH <fred.oh@intel.com>
Link: https://lore.kernel.org/r/20210802152151.15832-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Elitepad 1000 G2 has 2 headset jacks:
1. on the dock which uses the output of the codecs built-in HP-amp +
the standard IN2 input which is always used with the headset-jack.
2. on the tablet itself, this uses the line-out of the codec, combined
with an external HP-amp + IN1 for the headset-mic.
Fix the HP ElitePad 1000 G2 to properly reflect this now that the
machine-driver supports this setup.
Note this also changes the mapping for the internal mic. from
IN1 (which was pointing to the 2nd headset-jack mic) to DMIC2
which is the actual input for the internal mics.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213415
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices (HP Elitepad 1000 G2) have 2 headset jacks (1 on the dock,
2nd on the tablet itself). The 2nd headset mic input on these is
connected to in1 (the internal mics on the HP Elitepad 1000 G2 use DMIC2).
Add support for this through a new BYT_RT5640_HSMIC2_ON_IN1 quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices (HP Elitepad 1000 G2) have a second headphones output
(1 on the dock, 2nd on the tablet itself) which is implemented through
the line-out output of the codec combined with an external hp-amp
which gets enabled through the codec's GPIO1 pin.
Add support for this through a new BYT_RT5640_LINEOUT_AS_HP2 quirk,
note users are expected to use this combined with the
BYT_RT5640_LINEOUT quirk. If that quirk is not set the new quirk is
ignored.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a byt_rt5640_get_codec_dai() helper, which gets the codec_dai
from a dapm_context.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for boards which use the codecs Line Out output, this can
be enabled by using the newly added BYT_RT5640_LINEOUT quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the "Platform Clock" routes for the "Internal Mic" and "Speaker"
routes to the intmic_*_map[] / *_spk_map[] arrays.
This ensures that these "Platform Clock" routes do not get added when the
BYT_RT5640_NO_INTERNAL_MIC_MAP / BYT_RT5640_NO_SPEAKERS quirks are used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210802142501.991985-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The default codec for speaker amp's DAI Link is max98373 and will be
overwritten in probe function if the board id is sof_da7219_mx98360a.
However, the probe function does not do it because the board id is
changed in earlier commit.
Fixes: 1cc04d195d ("ASoC: Intel: sof_da7219_max98373: shrink platform_id below 20 characters")
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210726094525.5748-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The same quirk is used for LAPBC510 and LAPBC710 skews who use the
same audio design, with an RT711 headset codec using JD1 mode and one
RT1308 amplifier, along with 4 DMICs.
BugLink: https://github.com/thesofproject/linux/issues/3049
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210719233248.557923-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for SoundWire mockup devices. The configurations assume the
same topology as the CML SoundWire devices and can be used to test the
SOF firmware on a development board (RVP, UpExtreme) without any
hardware connected.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20210714032209.11284-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ADL RVP uses different circuits for jack detection, hence
adding external resister 100k mode.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: jairaj arava <jairaj.arava@intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need to redefine enum rt711_jd_src.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 683b0df26c ("ASoC: rt711: add two jack detection modes")
added two jack detection modes. Rt711 has 4 JD modes now.
Reserve 4 bits in case rt711 adds more JD modes in the future.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Refactor the machine driver by using the common code in maxim-common
module to support max98360a.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver data for jsl_cs4242_mx98360a which supports two
max98360a speaker amplifiers on SSP1 and cs42l42 headphone codec on
SSP0 running on JSL platform.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move max98360a code to this common module so it could be shared
between multiple SOF machine drivers. MAX98357A and MAX98360A are
sharing same codec driver so here we also share some function and
structures.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently there are two types of DAI Link sequences defined in
topology files, one starts from speaker link and the other starts from
headphone link.
Type 1: SPK - HP - DMIC - HDMI
Type 2: HP - DMIC - HDMI - SPK
Here we add a macro SOF_CS42L42_DAILINK to define the DAI Link
sequence in quirk and refactor the sof_card_dai_links_create()
function to support arbitrary DAI Link sequence.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712203240.46960-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use sof_dai_get_bclk() function to get bclk frequency instead of a
hard-coded magic number depending on configuration in topology.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210625205042.65181-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
On TGL platform with max98373 codec the trigger start sequence is
fe first, then codec component and sdw link is the last. Recently
a delay was introduced in max98373 codec driver and this resulted
to the start of sdw stream transmission was delayed and the data
transmitted by fw can't be consumed by sdw controller, so xrun happened.
Adding delay in trigger function is a bad idea. This patch enable spk
pin in prepare function and disable it in hw_free to avoid xrun issue
caused by delay in trigger.
Fixes: 3a27875e91 ("ASoC: max98373: Added 30ms turn on/off time delay")
BugLink: https://github.com/thesofproject/sof/issues/4066
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210625205042.65181-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Kconfig documentation for SND_SOC_INTEL_SKL_HDA_DSP_GENERIC_MACH
is a bit misleading as it refers to a set of older platforms,
while in practise this machine driver supports all modern
Intel systems with Smart Sound Technology based DSP and HDA codecs.
Modify the Kconfig text to reflect current state.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When we have a platform_device_id table, we can use
MODULE_DEVICE_TABLE to automatically generate the modalias. As a
result we can remove the manual insertion of MODULE_ALIAS.
Reported-by: Hulk Robot <hulkci@huawei.com>
Suggested-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse throws the following warning:
sound/soc/intel/boards/sof_sdw.c:796:31: error: incorrect type in argument 6 (different signedness)
sound/soc/intel/boards/sof_sdw.c:796:31: expected int *group_id
sound/soc/intel/boards/sof_sdw.c:796:31: got unsigned int *
The group_id cannot be negative, use unsigned int.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse throws the following warning:
sound/soc/intel/boards/sof_da7219_max98373.c:438:25: error: too long
initializer-string for array of char(no space for nul char)
Fix by using 'mx' acronym for Maxim.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse throws the following warnings:
sound/soc/intel/boards/kbl_da7219_max98357a.c:647:25: error: too long
initializer-string for array of char(no space for nul char)
Fix by using the 'mx' acronym for Maxim.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse throws the following warning:
sound/soc/intel/boards/glk_rt5682_max98357a.c:622:25: error: too long
initializer-string for array of char(no space for nul char)
Fix by using the 'mx' acronym for Maxim
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Chromebooks machine driver aliases exceed 20 characters, which
leads to sparse warnings:
sound/soc/intel/boards/sof_rt5682.c:959:25: error: too long
initializer-string for array of char(no space for nul char)
sound/soc/intel/boards/sof_rt5682.c:989:25: error: too long
initializer-string for array of char(no space for nul char)
sound/soc/intel/boards/sof_rt5682.c:1039:25: error: too long
initializer-string for array of char(no space for nul char)
Fix by using the 'mx' shortcut for Maxim platforms (already used in
platform firmware)
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove support for using hdac_hdmi codec driver. No known products use
this configuration and hdac_hdmi cannot support all the platforms
sof_sdw does.
This change also fixes a bug in Kconfig rules.
SND_SOC_INTEL_SOUNDWIRE_SOF_MACH did not have a select SND_SOC_HDAC_HDMI
and this could cause build failures.
Reported-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Tested-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On the reference boards, number of PCH dmics may vary and the number
should be taken from driver machine data. Remove the SOF_SDW_PCH_DMIC
quirk to make DMIC number configurable.
Fixes:d25bbe80485f8 ("ASoC: Intel: sof_sdw: add quirk for new ADL-P Rvp")
BugLink: https://github.com/thesofproject/sof/issues/4185
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210621194057.21711-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Updates for v5.14-rc1 are:
- Core has odd updates including improving clock stop codes, write api,
handling ENODATA etc
- Drivers has Big move of Intel driver to be aux dev and minor updates
to Intel/cadence driver
-----BEGIN PGP SIGNATURE-----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=JGCd
-----END PGP SIGNATURE-----
Merge tag 'soundwire-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire updates for 5.14-rc1
Updates for v5.14-rc1 are:
- Core has odd updates including improving clock stop codes, write api,
handling ENODATA etc
- Drivers has Big move of Intel driver to be aux dev and minor updates
to Intel/cadence driver
* tag 'soundwire-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: Fix test for DP prepare complete
soundwire: bus: Make sdw_nwrite() data pointer argument const
soundwire: intel: move to auxiliary bus
soundwire: cadence: remove the repeated declaration
soundwire: dmi-quirks: remove duplicate initialization
soundwire: cadence_master: always set CMD_ACCEPT
soundwire: bus: add missing \n in dynamic debug
soundwire: bus: handle -ENODATA errors in clock stop/start sequences
soundwire: add missing kernel-doc description
soundwire: bus: only use CLOCK_STOP_MODE0 and fix confusions
soundwire: bandwidth allocation: improve error messages
soundwire/ASoC: add leading zeroes in peripheral device name
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210617103538.1818-1-thunder.leizhen@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of fixes that have come in since the merge window, mainly
device specific things. The fixes to the generic cards from
Morimoto-san are handling regressions that were introduced in the merge
window on at least the Kontron sl28-var3-ads2.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmCraeoACgkQJNaLcl1U
h9BuVgf+Ith7351Fz+Jd1Y8e0rdVXuR4qVrkwm6u93/PRmFsL8DDWfURiHPuXJ+W
7NgsyreQEDLJYom8qloda/Lva2+FB0BHHkzUVLiZ7mDdbYq9Dush0QLLnOSP4p3O
GeeFJeK4EkeGHHFBbFllJ6gVB9xiokEcghXz1a+PkNMkYuQpAswlvhHxlIfEk1Bv
p1DBcM3gfT+3kfGynyz9A2O01zSd34Eg7tQuMqObxwFwpWY9mzrlYaPLdLF7Vtgc
JyQVvjTMaUZtiN/zGUFyXxAboTGWIFlPJKvHLHCiKvivSveXamziasieUwDU/cBL
X5SuIh883CghMhp8Dtx39zpcuiwEZQ==
=sQPM
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.13-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.13
A collection of fixes that have come in since the merge window, mainly
device specific things. The fixes to the generic cards from
Morimoto-san are handling regressions that were introduced in the merge
window on at least the Kontron sl28-var3-ads2.
Brya is another ADL-P product.
AlderLake has support for Bluetooth audio offload capability.
Enable the BT-offload quirk for ADL-P Brya and the Intel RVP.
Signed-off-by: Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210521155632.3736393-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620791647-16024-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse throwns the following warnings:
sound/soc/intel/boards/bxt_da7219_max98357a.c:843:19: error: too long
initializer-string for array of char(no space for nul char)
sound/soc/intel/boards/bxt_da7219_max98357a.c:844:19: error: too long
initializer-string for array of char(no space for nul char)
sound/soc/intel/boards/bxt_da7219_max98357a.c:845:19: error: too long
initializer-string for array of char(no space for nul char)
Fix by using the 'mx' acronyn for Maxim
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210511213707.32958-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_id is too long and is flagged by a sparse warning:
sound/soc/intel/boards/sof_cs42l42.c:483:25: error: too long
initializer-string for array of char(no space for nul char)
fix by using the 'mx' acronym for Maxim
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Paul Olaru <paul.olaru@oss.nxp.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20210511213707.32958-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Lenovo Miix 3-830 tablet has only 1 speaker, has an internal analog
mic on IN1 and uses JD2 for jack-detect, add a quirk to automatically
apply these settings on Lenovo Miix 3-830 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210508150146.28403-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Glavey TM800A550L tablet, this BYTCR tablet has no CHAN
package in its ACPI tables and uses SSP0-AIF1 rather then SSP0-AIF2 which
is the default for BYTCR devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210508150146.28403-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We recently added leading zeroes in dev_dbg() messages but forgot to
do the same for the peripheral device name. Adding leading zeroes
makes it easier to read manufacturer ID and part ID, e.g.:
sdw:0:025d:0700:00
sdw:0:025d:0711:00
sdw:1:025d:0700:00
sdw:1:025d:1308:00
sdw:2:025d:0700:00
sdw:2:025d:0701:00
sdw:3:025d:0700:00
sdw:3:025d:0715:00
The use of '01x' for link_id and unique_id is intentional to show the
value range in the code, it's understood it does not actually change
the format.
To avoid problems with git bisect, the same change needs to be applied
to the Intel SoundWire machine driver, otherwise the components can't
be found and the card registration fails.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210511060137.29856-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Refactor the machine driver by using the common code in maxim-common
module to support max98357a.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-14-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The machine driver is a generic machine driver for SOF with cs42l42
I2C codec. It currently supports Maxim MAX98357A speker amp on GLK
but is extensible for other apms and platforms.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-13-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move max98357a code to this common module so it could be shared
between multiple SOF machine drivers.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-12-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AlderLake needs the flag SOF_RT715_DAI_ID_FIX if it is using the
rt715 DMIC.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Somehow with copy/paste and inertia we keep re-adding this field for
BE dailinks, when it's only required for hard-coded FE links.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sof_maxim_common.o is linked twice, move to a dedicated module.
Also clean-up interfaces to use a consistent 'max_98373' prefix for
all symbols.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
hda-dsp-common.o is linked multiple times due to copy/paste and
inertia. Move to a dedicated module with a namespace.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When external RT714/715 devices are used for capture, we don't want
the PCH DMICs to be used.
Any information provided by the SOF platform driver or DMI quirks will
be overridden.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ADL customer boards are with below 2 configurations
Board 1: RT5682 on SSP0 and MAX98373 on SSP1
Board 2: RT5682 on SSP0 and MAX98357A on SSP2
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
BT audio offload is internally configured with virtual GPIOs,
the port assignment is fixed on SSP2 for TGL/ADL platforms.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210505163705.305616-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add quirks for jack detection, rt711 DAI and DMIC
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210415175013.192862-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
kabylake_ssp_fixup function uses snd_soc_dpcm to identify the
codecs DAIs. The HW parameters are changed based on the codec DAI of the
stream. The earlier approach to get snd_soc_dpcm was using container_of()
macro on snd_pcm_hw_params.
The structures have been modified over time and snd_soc_dpcm does not have
snd_pcm_hw_params as a reference but as a copy. This causes the current
driver to crash when used.
This patch changes the way snd_soc_dpcm is extracted. snd_soc_pcm_runtime
holds 2 dpcm instances (one for playback and one for capture). 2 codecs
on the SSP are dmic (capture) and speakers (playback). Based on the
stream direction, snd_soc_dpcm is extracted from snd_soc_pcm_runtime.
Tested for all use cases of the driver.
Based on similar fix in kbl_rt5663_rt5514_max98927.c
from Harsha Priya <harshapriya.n@intel.com> and
Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Cc: <stable@vger.kernel.org> # 5.4+
Signed-off-by: Lukasz Majczak <lma@semihalf.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210415124347.475432-1-lma@semihalf.com
Signed-off-by: Mark Brown <broonie@kernel.org>
create dai link in kbl_da7219_max98357a driver for wake on voice
functionality.
changes picked from broonie's tree
commit 0c7941a63a
("ASoC: Intel: Skylake: Use refcap device for mono recording")
commit 2154be362c
("ASoc: Intel: boards: Add WOV as sink for nau88l25_ssm4567 machine")
Signed-off-by: Mac Chiang <mac.chiang@intel.com>
Signed-off-by: Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Tested-by: Kaiyen Chang <kaiyen.chang@intel.corp-partner.google.com>
Tested-by: luke yang <luke_yang@compal.corp-partner.google.com>
Tested-by: Grace Kao <grace.kao@intel.com>
Tested-by: Kaiyen Chang <kaiyen.chang@intel.com>
Reviewed-by: Cheng-Yi Chiang <cychiang@chromium.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210405124835.71247-3-vamshi.krishna.gopal@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To support MST hdmi audio, modify the current routes to be
based on port in kbl_da7219_max98357a, kbl_da7219_max98927 &
kbl_rt5663_max98927.
Signed-off-by: Vamshi Krishna Gopal <vamshi.krishna.gopal@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210405124835.71247-2-vamshi.krishna.gopal@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the card.components string using the new rt5670_components() helper
which returns a components string based on the DMI quirks inside the
rt5670 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210402140747.174716-7-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5672 codec is used on some Bay Trail CR boards, on these SoCs SSP2
is not available and SSP0 should be used instead. At support for this.
This has been tested on a Dell Venue 10 Pro 5055.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210402140747.174716-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Chuwi Hi8 tablet is using an analog mic on IN1 and has its
jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
It also only has 1 speaker.
Add a quirk applying the correct settings for this configuration.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210325221054.22714-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add jack detect support by creating a jack and calling
snd_soc_component_set_jack to register the created jack
with the codec.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307151807.35201-14-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We should use the topology configured mclk if it existed, which can make
sure we are aligned with the FW side about the mclk usage.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210319124950.3853994-2-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds jsl_rt5682_rt1015p which supports the RT5682 headset
codec and ALC1015Q-VB speaker amplifier combination on JasperLake
platform.
This driver also supports ALC1015Q-CG if running in auto-mode.
Following table shows the audio interface support of the two
amplifiers.
| ALC1015Q-CG | ALC1015Q-VB
=====================================
I2C | Yes | No
Auto-mode | 48K, 64fs | 16k, 32fs
| 48k, 32fs
| 48k, 64fs
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210317110824.20814-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on which AIF is used the UCM profile needs to setup
a different path through the rt5640's "Digital Mixer Path" graph.
ATM the UCM profiles solve this by just enabling paths to the outputs /
from the input from both AIF1 and AIF2 and then relying on the DAPM
framework to power-down the parts of the graph connected to the
unused AIF.
But in order to be able to use hardware-volumecontrol and to use
the hardware mute controls, which are necessary for mute LED control,
the UCM profiles need to know which AIF is actually being used.
Add a new "aif:1" or "aif:2" part to the component string to provide
info about the used AIF to userspace / to the UCM profiles.
Note the size of byt_rt5640_components is not increased because the
size of 32 chars already is big enough.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210307150503.34906-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Asus T100TAF uses the same jack-detect settings as the T100TA,
this has been confirmed on actual hardware.
Add these settings to the T100TAF quirks to enable jack-detect support
on the T100TAF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210312114850.13832-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
make W=1 warning:
sound/soc/intel/boards/bytcr_wm5102.c:216:40: error:
‘byt_wm5102_dai_params’ defined but not used
[-Werror=unused-const-variable=]
216 | static const struct snd_soc_pcm_stream byt_wm5102_dai_params = {
| ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210302205926.49063-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the return from snd_soc_dai_set_pll is not checking for
failure, this is the only driver in the kernel that ignores this,
so it probably should be added for sake of completeness. Fix this
by adding an error return check.
Addresses-Coverity: ("Unchecked return value")
Fixes: f139546fb7 ("ASoC: Intel: boards: sof-wm8804: support for Hifiberry Digiplus boards")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210226185653.1071321-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When I added the quirk for the "HP Pavilion x2 10-p0XX" I copied the
byt_rt5640_quirk_table[] entry for the HP Pavilion x2 10-k0XX / 10-n0XX
models since these use almost the same settings.
While doing this I accidentally also copied and kept the non-standard
OVCD_TH_1500UA setting used on those models. This too low threshold is
causing headsets to often be seen as headphones (without a headset-mic)
and when correctly identified it is causing ghost play/pause
button-presses to get detected.
Correct the HP Pavilion x2 10-p0XX quirk to use the default OVCD_TH_2000UA
setting, fixing these problems.
Fixes: fbdae7d6d0 ("ASoC: Intel: bytcr_rt5640: Fix HP Pavilion x2 Detachable quirks")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210224105052.42116-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Acer One S1002 tablet is using an analog mic on IN1 and has
its jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
Note it is also using AIF2 instead of AIF1 which is somewhat unusual,
this is correctly advertised in the ACPI CHAN package, so the speakers
do work without the quirk.
Add a quirk for the mic and jack-detect settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-5-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a DMI quirk for the Jumper EZpad 7 tablet, this tablet has
a jack-detect switch which reads 1/high when a jack is inserted,
rather then using the standard active-low setup which most
jack-detect switches use. All other settings are using the defaults.
Add a DMI-quirk setting the defaults + the BYT_RT5651_JD_NOT_INV
flags for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Voyo Winpad A15 tablet uses a Bay Trail (non CR) SoC, so it is using
SSP2 (AIF1) and it mostly works with the defaults. But instead of using
DMIC1 it is using an analog mic on IN1, add a quirk for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Estar Beauty HD MID 7316R tablet almost fully works with out default
settings. The only problem is that it has only 1 speaker so any sounds
only playing on the right channel get lost.
Add a quirk for this model using the default settings + MONO_SPEAKER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210216213555.36555-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire machine drivers make a heavy use of component prefixes to
uniquify control names. This however results in errors when looking
for widgets or pins. This patchset suggests two solutions but feedback
or suggestions on how to take the prefix into account would be
welcome.
Bard Liao (1):
ASoC: Intel: boards: max98373: get dapm from cpu_dai
Shuming Fan (1):
ASoC: dapm: use component prefix when checking widget names
sound/soc/intel/boards/sof_maxim_common.c | 5 +++--
sound/soc/soc-dapm.c | 13 ++++++++++++-
2 files changed, 15 insertions(+), 3 deletions(-)
--
2.25.1
We create dai links dynamically, so it is not easy to know what dai
links are created. So adding trace for dai link name and id.
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver create DMIC dai based on quirk for each platforms,
so we need to add quirk for new platforms. Now driver reports DMIC
number to machine driver and machine driver can create DMIC dai based
on this information. The old check is reserved for some platforms
may be failed to set the DMIC number in BIOS.
Reviewed-by: Bard Liao <bard.liao@intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
UCM needs to know which microphone is used (dmic or RT715-based),
let's add the information in the component string.
Note the slight change from HDAudio platforms where 'cfg-dmics' was
used. 'cfg-mics' is used here with the intent that this component
string describes either the number of PCH-attached microphones or the
number of RT715-attached ones (the assumption is that the two
configurations are mutually exclusive).
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the same style for all quirks to avoid misses and errors
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The quirk table is a mess, let's reorganize it by generation before
making sure that the quirks are consistent for each generation.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210208233336.59449-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a prefix on max98373 codec, and the prefix will be added to
the pin name However, there is no prefix on the "Right Spk" and "Left
Spk" widgets.
To avoid getting a redundant prefix, we should get dapm from cpu_dai
component.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210208234043.59750-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new ASoc Machine driver for Intel Baytrail platforms with a
Wolfson Microelectronics WM5102 codec.
This is based on a past contributions [1] from Paulo Sergio Travaglia
<pstglia@gmail.com> based on the Levono kernel [2] combined with
insights in things like the speaker GPIO from the android-x86 android
port for the Lenovo Yoga Tablet 2 1051F/L [3].
[1] https://patchwork.kernel.org/project/alsa-devel/patch/593313f5.3636c80a.50e05.47e9@mx.google.com/
[2] https://github.com/lenovo-yt2-dev/android_kernel_lenovo_baytrail/blob/cm-12.1/sound/soc/intel/board/byt_bl_wm5102.c
[3] https://github.com/Kitsune2222/Android_Yoga_Tablet_2-1051F_Kernel
The original machine driver from the Android ports was a crude modified
copy of bytcr_rt5640.c adjusted to work with the WM5102 codec.
This version has been extensively reworked to:
1. Remove all rt5640 related quirk handling. to the best of my knowledge
this setup is only used on the Lenovo Yoga Tablet 2 series (8, 10 and 13
inch models) which all use the same setup. So there is no need to deal
with all the variations with which we need to deal on rt5640 boards.
2. Rework clock handling, properly turn off the FLL and the platform-clock
when they are no longer necessary and don't reconfigure the FLL
unnecessarily when it is already running. This fixes a number of:
"Timed out waiting for lock" warnings being logged.
3. Add the GPIO controlled Speaker-VDD regulator as a DAPM_SUPPLY
This only adds the machine driver and ACPI hooks, the BYT-CR detection
quirk which these devices need will be added in a separate patch.
BugLink: https://github.com/thesofproject/linux/issues/2485
Co-authored-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210120214957.140232-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We missed adding the TGL_HDMI quirk which is very much needed to
expose the 4 display pipelines and will be required on TGL topologies.
Fixes: e787f5b5b1 ('ASoC: Intel: add support for new SoundWire hardware layout on TGL')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210204203312.27112-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We missed adding the TGL_HDMI quirk which is very much needed to
expose the 4 display pipelines and will be required on TGL topologies.
Fixes: 488cdbd893 ('ASoC: Intel: sof_sdw: add quirk for new TigerLake-SDCA device')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210204203312.27112-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We missed adding the TGL_HDMI quirk which is very much needed to
expose the 4 display pipelines and will be required on TGL topologies.
Fixes: 9ad9bc59dd ('ASoC: Intel: sof_sdw: set proper flags for Dell TGL-H SKU 0A5E')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210204203312.27112-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add flag "SOF_RT711_JD_SRC_JD2", flag "SOF_RT715_DAI_ID_FIX"
and "SOF_SDW_FOUR_SPK" to the Dell TGL-H based SKU "0A5E".
Signed-off-by: Libin Yang <libin.yang@intel.com>
Co-developed-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210125081117.814488-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi All,
This series adds support for devices with only a headphone jack
(no speakers/internal mic). Specifically this adds support for the
Mele PCG03 Mini PC. But the new no-speakers and no-internal-mic quirks
will likely be useful on other devices too.
Regards,
Hans
Move the snd_soc_dai_set_tdm_slot() call from cht_codec_init() to
cht_codec_fixup(). There are 2 reasons for doing this:
1. This aligns the cht_bsw_nau8824 with all the other BYT/CHT machine
drivers which also do this from their codec_fixup function.
2. When using the SOF driver, things like the TDM info is set from the
topology file. Moving the call to the codec_fixup function, which gets
skipped when using the SOF driver avoids the call interfering with the
settings when using the SOF driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210107115324.11602-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Mele PCG03 Mini PC, being a Mini PC this device
has no speakers and no internal microphone.
To make matters worse the speaker output pins are shorted (to gnd or
to each other?) and SPKVDD is provided. So trying to output sound on the
speakers leads to shorting SPKVDD, this leads to a power dip after
which the codec is an unknown state. Sometimes it drops of the i2c
bus, sometimes it does still respond to i2c transfers, but is otherwise
not functional. TL;DR: trying to use the speaker outputs on this model
is BAD.
Besides not having speakers / an internal mic, this is a Bay Trail CR
device without a CHAN package in ACPI, so we default to SSP0-AIF2 as
codec connection. But the device is actually using SSP0-AIF1, so we
need to quirk that too.
Cc: Rasmus Porsager <rasmus@beat.dk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210109210119.159032-4-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices, like mini PCs/media/top-set boxes do not have an internal
microphone at all, an example of the is the Mele PCG03 Mini PC.
Add a new BYT_RT5640_NO_INTERNAL_MIC_MAP input-mapping for this,
which does not add any internal-mic routes and modifies the components
and the (optional) long_name strings to reflect this.
Cc: Rasmus Porsager <rasmus@beat.dk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210109210119.159032-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices, like mini PCs/media/top-set boxes do not have any speakers
at all, an example of the is the Mele PCG03 Mini PC.
Add a new BYT_RT5640_NO_SPEAKERS quirk-flag which when sets does not add
speaker routes and modifies the components and the (optional) long_name
strings to reflect that there are no speakers.
Cc: Rasmus Porsager <rasmus@beat.dk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210109210119.159032-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove a stale comment about SSP0 being untested, the
bytcht_es8316 has supported SSP0 for a while now and this has
been successfully tested on a GP electrinic T701 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210107120757.12051-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
bclk_ratio is unused. Removes bclk_ratio and .set_bclk_ratio callback.
Removes snd_soc_dai_set_bclk_ratio() in a few machine drivers which are
obviously using rt1015.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Link: https://lore.kernel.org/r/20201224101854.3024823-1-tzungbi@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
haswell machine board is missing pm_ops what prevents it from undergoing
suspend-resume procedure successfully. Assign default snd_soc_pm_ops so
this is no longer the case.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201217105401.27865-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tha ARCHOS Cesium 140 tablet has problem with the jack-sensing,
thus the heaset functions are not working.
Add quirk for this model to select the correct input map, jack-detect
options and channel map to enable jack sensing and headset microphone.
This device uses IN1 for its internal MIC and JD2 for jack-detect.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201208060414.27646-1-chiu@endlessos.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd-soc-sst-acpi driver does not care about the id specified for
the SSP2-Codec DAI, but it does matter for the snd-sof-acpi driver;
and when it is not 0 then the snd-sof-acpi driver does not work.
Set the SSP2-Codec DAI id to 0, fixing the snd-sof-acpi driver not
working on devices using the cht_bsw_nau8824 machine-driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201206122436.13553-3-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the snd-soc-sst-acpi driver then the compress-cpu-dai bits are
not used, the cht_bsw_nau8824 machine-driver is the only BYT/CHT driver
defining them.
When using the snd-sof-acpi driver then the presence of the
compress-cpu-dai bits breaks things because the sof topology file for
by/cht devices does not contain routing info for them.
Drop the compress-cpu-dai bits, fixing the snd-sof-acpi driver not
working on devices using the cht_bsw_nau8824 machine-driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201206122436.13553-2-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the driver data for two rt1011 speaker amplifiers on
SSP1 and rt5682 on SSP0 for TGL platform. DAI format for rt1011 is
leveraged from cml_rt1011_rt5682 which is 4-slot tdm with 100fs bclk.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201203154010.29464-1-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Speaker amp's SSP bclk configuration was changed in the topology file to be
based on 12.288MHz and dai_ops->hw_params is based on s32le format.
But, the TDM slot size remained set to 24 bits.
This inconsistency created audible noises and needs to be corrected.
This patch updates TDM slot width to 32.
Fixes: bc7477fc2a ("ASoC: Intel: Boards: tgl_max98373: Update TDM configuration in hw_params")
Signed-off-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201201211150.433472-1-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Atom/SST driver does not rely on ASoC power management, but the
SOF driver does. Rather than using a hard-coded build-time assignment,
we can set this pm_ops dynamically depending on what the parent
is. That will remove the last build-time dependency and allow for
coexistence of both SST and SOF drivers for Baytrail/Cherrytrail.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To avoid hard-coded variations between SOF and SST drivers, set the
card name and driver dynamically depending on the parent type. This is
the first pass required to let distributions select which drivers to
use with kernel parameters instead of build-time selection.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason this ops is missing in 2 out of the 3 broadwell
drivers. Add to make sure ASoC takes care of power management.
Tested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason this ops is missing in 2 out of the 3 broadwell
drivers. Add to make sure ASoC takes care of power management.
Tested-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201112223825.39765-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The HP Pavilion x2 Detachable line comes in many variants:
1. Bay Trail SoC + AXP288 PMIC, Micro-USB charging (10-k010nz, ...)
DMI_SYS_VENDOR: "Hewlett-Packard"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable PC 10"
DMI_BOARD_NAME: "8021"
2. Bay Trail SoC + AXP288 PMIC, Type-C charging (10-n000nd, 10-n010nl, ...)
DMI_SYS_VENDOR: "Hewlett-Packard"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable"
DMI_BOARD_NAME: "815D"
3. Cherry Trail SoC + AXP288 PMIC, Type-C charging (10-n101ng, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP Pavilion x2 Detachable"
DMI_BOARD_NAME: "813E"
4. Cherry Trail SoC + TI PMIC, Type-C charging (10-p002nd, 10-p018wm, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP x2 Detachable 10-p0XX"
DMI_BOARD_NAME: "827C"
5. Cherry Trail SoC + TI PMIC, Type-C charging (x2-210-g2, ...)
DMI_SYS_VENDOR: "HP"
DMI_PRODUCT_NAME: "HP x2 210 G2"
DMI_BOARD_NAME: "82F4"
Variant 1 needs the exact same quirk as variant 2, so relax the DMI check
for the existing quirk a bit so that it matches both variant 1 and 2
(note the other variants will still not match).
Variant 2 already has an existing quirk (which now also matches variant 1)
Variant 3 uses a cx2072x codec, so is not applicable here.
Variant 4 almost works with the defaults, but it also needs a quirk to
fix jack-detection, add a new quirk for this.
Variant 5 does use a RT5640 codec (based on old dmesg output), but was
otherwise not tested, keep using the defaults for this variant.
Fixes: ec8e8418ff ("ASoC: Intel: bytcr_rt5640: Add quirks for various devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201118121515.11441-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In kabylake_set_bias_level(), enabling mclk may fail if the clock has
already been enabled by the firmware. Attempts to disable that clock
later will fail with a warning backtrace.
mclk already disabled
WARNING: CPU: 2 PID: 108 at drivers/clk/clk.c:952 clk_core_disable+0x1b6/0x1cf
...
Call Trace:
clk_disable+0x2d/0x3a
kabylake_set_bias_level+0x72/0xfd [snd_soc_kbl_rt5663_rt5514_max98927]
snd_soc_card_set_bias_level+0x2b/0x6f
snd_soc_dapm_set_bias_level+0xe1/0x209
dapm_pre_sequence_async+0x63/0x96
async_run_entry_fn+0x3d/0xd1
process_one_work+0x2a9/0x526
...
Only disable the clock if it has been enabled.
Fixes: 15747a8020 ("ASoC: eve: implement set_bias_level function for rt5514")
Cc: Brent Lu <brent.lu@intel.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201111205434.207610-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Smart_amp_speaker device has the playback stream and capture stream
associated to it. Hence add the dpcm_capture = 1 flag while dailink
creation.
This patches fixes:
ERR kernel [timestamp] SSP1-Codec: ASoC: no backend capture stream
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20201109210958.84198-1-ranjani.sridharan@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This DMI product family string of this board is "Google_Hatch" so the
DMI quirk will take place. However, this board is using rt1015 speaker
amp instead of max98357a specified in the quirk. Therefore, we need an
new DMI quirk for this board.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201030170559.20370-3-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the driver data and updates quirk info for cml with
rt1015 speaker amp and rt5682 headset codec. Due to different mclk
frequency on JSL and CML, we need to use 4 slot TDM 100fs to avoid
the SSP m/n counter.
Signed-off-by: Brent Lu <brent.lu@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201030170559.20370-2-brent.lu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace commas with semicolons. What is done is essentially described by
the following Coccinelle semantic patch (http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/1602407979-29038-4-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
With sound/soc/intel/haswell and /baytrail gone, registers left within
sst-dsp header are atom-specific. Relocate these to atom internal header
to make atom truely independent of sound/soc/common processing code.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://lore.kernel.org/r/20201006064907.16277-12-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
byt-rt5640 is deprecated in favor of bytcr_rt5640 used by
sound/soc/intel/atom and SOF solutions both. Remove redundant machine
board and all related code.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://lore.kernel.org/r/20201006064907.16277-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
byt-max98090 is deprecated in favor of cht-bsw-max98090 used by
sound/soc/intel/atom and SOF solutions both. Remove redundant machine
board and all related code.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@intel.com>
Link: https://lore.kernel.org/r/20201006064907.16277-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
PCM operations for DAI links connected with DSP platform component
involve communication with DSP firmware by IPCs. As IPC protocol may
cause thread to sleep while waiting for a response from DSP, propagate
that information to ALSA core by marking all FE DAIs as nonatomic.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201004090609.29066-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
RT715 and RT714 are essentially the same chip. In addition, there are
two versions, one supporting SoundWire 1.1 and one supporting
SoundWire 1.2 (SDCA).
The previous configurations assumed that RT714 was SDCA-only, which
isn't correct. Add support for the 4 possible combinations to avoid
confusions.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Jack Yu <jack.yu@realtek.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20201002211902.287692-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Apply same test as for other amplifiers - in case we enable feedback
one day.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20201002211902.287692-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Prevent sound/soc/intel/haswell code compile and select catpt instead as
a recommended solution. Userspace-exposed members are compatible with
what is exposed by deprecated solution thus no harm is done. The only
visible difference is the newly added 'Loopback Mute' kcontrol.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200929141247.8058-15-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hans de Goede
Cezary Rojewski
Heikki Krogerus
Pierre-Louis Bossart
Mark Brown
jairaj arava
Brent Lu
Bard Liao
Linus Torvalds
Rander Wang
Kai Vehmanen
Greg Kroah-Hartman
Zhen Lei
Mark Brown
Takashi Iwai
Vamshi Krishna Gopal
Zou Wei
Libin Yang
Yong Zhi
Lukasz Majczak
Mac Chiang
Keyon Jie
Colin Ian King
Tzung-Bi Shih
Chris Chiu
Sathyanarayana Nujella
Guenter Roeck
Geert Uytterhoeven
Dharageswari R
Julia Lawall
Tomasz Figa