amdgpu_dm_crtc_late_register() is only used when CONFIG_DEBUG_FS
is enabled so make it dependent on that.
Fixes: 4cd79f614b ("drm/amd/display: Move connector debugfs to drm")
Cc: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Link: https://lists.freedesktop.org/archives/dri-devel/2022-June/359496.html
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220615210019.28943-1-alexander.deucher@amd.com
[Why]
DIO parameters were missing in topology_update_intput_v3 struct.
[How]
Add DIO parameters in v3 struct and update in functions perspectively.
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] when 4k@144hz dp connect to dp1.4 dsc mst hub, requested
bandwidth exceeds caps of dsc hub. but dsc bw valid functions,
increase_dsc_bpp, try_disable_dsc, pre_validate_dsc,
compute_mst_dsc_configs_for_state, do not return false to
atomic check. this cause user mode initiate mode set to kernel,
then cause kernel assert, system hang.
[How] dsc bandwidth valid functions return pass or fail to atomic
check.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
There are cases where swizzle modes are set but modifiers arent. For
such a userspace, we need not check modifiers while checking
compatibilty in the drm hook for checking plane format.
Ignore checking modifiers but check the DCN generation for the
supported swizzle mode.
v2: squash in unused variable removal (Alex)
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For OLED eDP the Display Manager uses max_cll value as a limit
for brightness control.
max_cll defines the content light luminance for individual pixel.
Whereas max_fall defines frame-average level luminance.
The user may not observe the difference in brightness in between
max_fall and max_cll.
That negatively impacts the user experience.
[How]
Use max_fall value instead of max_cll as a limit for brightness control.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Once mst topology is constructed, later on new connected monitors
are reported to source by CSN message. Within CSN, there is no
carried info of DPCD_REV comparing to LINK_ADDRESS reply. As the
result, we might leave some ports connected to DP but without DPCD
revision number which will affect us determining the capability of
the DP Rx.
[How]
Send out remote DPCD read when the port's dpcd_rev is 0x0 in
detect_ctx(). Firstly, read out the value from DPCD 0x2200. If the
return value is 0x0, it's likely the DP1.2 DP Rx then we reques
revision from DPCD 0x0 again.
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For additional power savings, PSR SU (also referred to as PSR2) can be
enabled on eDP panels with PSR SU support.
PSR2 saves more power compared to PSR1 by allowing more opportunities
for the display hardware to be shut down. In comparison to PSR1, Shut
down can now occur in-between frames, as well as in display regions
where there is no visible update. In otherwords, it allows for some
display hw components to be enabled only for a **selectively updated**
region of the visible display. Hence PSR SU.
[HOW]
To define the SU region, support from the OS is required. OS needs to
inform driver of damaged regions that need to be flushed to the eDP
panel. Today, such support is lacking in most compositors.
Therefore, an in-between solution is to implement PSR SU for MPO and
cursor scenarios. The plane bounds can be used to define the damaged
region to be flushed to panel. This is achieved by:
* Leveraging dm_crtc_state->mpo_requested flag to identify when MPO is
enabled.
* If MPO is enabled, only add updated plane bounds to dirty region.
Determine plane update by either:
* Existence of drm damaged clips attached to the plane (added by a
damage-aware compositor)
* Change in fb id (flip)
* Change in plane bounds (position and dimensions)
* If cursor is enabled, the old_pos and new_pos of cursor plus cursor
size is used as damaged regions(*).
(*) Cursor updates follow a different code path through DC. PSR SU for
cursor is already implemented in DC, and the only thing required to
enable is to set DC_PSR_VERSION_SU_1 on the eDP link. See
dcn10_dmub_update_cursor_data().
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently the psr configuration parameters are hardcoded before
feeding into the DC helper before passing to DMUB FW. We'd rework
to call a shared helper to calculate/update generic psr config
fields which are relying on the stream timing and eDP sink PSR
caps to avoid hard-coding.
[how]
- drop part of hard-coded psr config fields by replacing w/ the
call of helper from DM before feeding into DC link setup psr
helper
- For those DM specific psr config fields, e.g. allow smu opt, is
not to be set/updated from the shared helper but to rely on the
DC feature mask
- for the psr version field in psr_config structure, since only
the field psr_version of DC link psr_settings matters for that
fed to DMUB FW, thus no need to set/update the psr_version field
of psr_config structure.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX11 IP introduces new tiling mode. Various combinations of DCC
settings are possible and the most preferred settings must be exposed
for optimal use of the hardware.
add_gfx11_modifiers() is based on recommendation from Marek for the
preferred tiling modifier that are most efficient for the hardware.
v2: microtiling fix noticed by Marek
v3: keep Z tiling check
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Display Manager specific changes for DCN3.2.x. DM
handles the interaction between the core DC modesetting
code and the drm modesetting infrastructure.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
lut pipeline will be hooked up differently in some asics
need to add new interfaces
how:
add them
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin <martin.leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
According to the KMS man page, there is a
"Coverage" alpha blend mode that assumes the
pixel color values have NOT been pre-multiplied
and will be done when the actual blending to
the background color values happens.
Previously, this mode hasn't been enabled
in our driver and it was assumed that all
normal overlay planes are pre-multiplied
by default.
When a 3rd party app is used to input a image
in a specific format, e.g. PNG, as a source
of a overlay plane to blend with the background
primary plane, the pixel color values are not
pre-multiplied. So by adding "Coverage" blend
mode, our driver will support those cases.
Issue fixed: Overlay plane alpha channel blending is incorrect
Issue tracker: https://gitlab.freedesktop.org/drm/amd/-/issues/1769
Reference:
https://dri.freedesktop.org/docs/drm/gpu/drm-kms.html#plane-composition-properties
Adding Coverage support also enables IGT
kms_plane_alpha_blend Coverage subtests:
1. coverage-7efc
2. coverage-vs-premult-vs-constant
Changes
1. Add DRM_MODE_BLEND_COVERAGE blend mode capability
2. Add "pre_multiplied_alpha" flag for Coverage case
3. Read the correct flag and set the DCN MPCC
pre_multiplied register bit (only on overlay plane)
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1769
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The > ARRAY_SIZE() should be >= ARRAY_SIZE() to prevent an out of bounds
access.
Fixes: e27c41d5b0 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As drm_connector already have the display_info, instead of creating
"output_bpc" debugfs in vendor specific driver, move the logic to
the drm layer.
This patch will also move "Current" bpc to the crtc debugfs from
connector debugfs, since we are getting this info from crtc_state.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519095149.3560034-4-bhanuprakash.modem@intel.com
This gives us the standard atomic implicit and explicit fencing rules.
v2: move the wait to amdgpu_dm_atomic_commit_tail
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Cc: Qingqing Zhuo <qingqing.zhuo@amd.com>
Cc: Jude Shih <shenshih@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220509074712.163899-1-christian.koenig@amd.com
[Why & How]
CONFIG_DRM_AMD_DC_DCN is used by pass the compilation failures, but DC
code should be OS-agnostic.
This patch fixes it by removing unnecessasry CONFIG_DRM_AMD_DC_DCN
in amdgpu_dm directory.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Observing error log about trying to disable non-implemented irq source
when user unload the driver.
[how]
Check and filter the invalid irq source before disabling it.
Reviewed-by: Qingqing (Lillian) Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Introduction of display-helper module, and rework of the DP, DSC,
HDCP, HDMI and SCDC headers
- doc: Improvements for tiny drivers, link to external resources
- formats: helper to convert from RGB888 and RGB565 to XRGB8888
- modes: make width-mm/height-mm check mandatory in of_get_drm_panel_display_mode
- ttm: Convert from kvmalloc_array to kvcalloc
Driver Changes:
- bridge:
- analogix_dp: Fix error handling in probe
- dw_hdmi: Coccinelle fixes
- it6505: Fix Kconfig dependency on DRM_DP_AUX_BUS
- panel:
- new panel: DataImage FG040346DSSWBG04
- amdgpu: ttm_eu cleanups
- mxsfb: Rework CRTC mode setting
- nouveau: Make some variables static
- sun4i: Drop drm_display_info.is_hdmi caching, support for the
Allwinner D1
- vc4: Drop drm_display_info.is_hdmi caching
- vmwgfx: Fence improvements
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCYmpHrQAKCRDj7w1vZxhR
xTC3AQDrZx4SIu9p76z9cRCDwvkOFs1H2Q/YJGnv6zU6QiSWBwD9ENTmaJslcSVw
+tYfhRo2Z0GEvhiKVmQPZ561TNUJzQU=
=4Bw4
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-04-28' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.19:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- Introduction of display-helper module, and rework of the DP, DSC,
HDCP, HDMI and SCDC headers
- doc: Improvements for tiny drivers, link to external resources
- formats: helper to convert from RGB888 and RGB565 to XRGB8888
- modes: make width-mm/height-mm check mandatory in of_get_drm_panel_display_mode
- ttm: Convert from kvmalloc_array to kvcalloc
Driver Changes:
- bridge:
- analogix_dp: Fix error handling in probe
- dw_hdmi: Coccinelle fixes
- it6505: Fix Kconfig dependency on DRM_DP_AUX_BUS
- panel:
- new panel: DataImage FG040346DSSWBG04
- amdgpu: ttm_eu cleanups
- mxsfb: Rework CRTC mode setting
- nouveau: Make some variables static
- sun4i: Drop drm_display_info.is_hdmi caching, support for the
Allwinner D1
- vc4: Drop drm_display_info.is_hdmi caching
- vmwgfx: Fence improvements
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 28 Apr 2022 17:52:13 AEST
# gpg: using EDDSA key 5C1337A45ECA9AEB89060E9EE3EF0D6F671851C5
# gpg: Can't check signature: No public key
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428075237.yypztjha7hetphcd@houat
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
drm/drm-next has a build fix for the NewVision NV3052C panel
(drivers/gpu/drm/panel/panel-newvision-nv3052c.c), which needs to be
merged back to drm-misc-next, as it was failing to build there.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
[why]
creating a generic helper for AMD specific PSR-SU sink validation.
Moving the function to the power module to reference it across all
OS.
[how]
- drop PSRSU specific sink validation helper and move to power
module by reading PSR version and other PSR caps
- call the new helper from linux DM (amdgpu_dm_psr)
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] within dc link detecion, dp link training will be
executed for external sst dp. for debug purpose, we may
need skip dp link training.
[How] expose dc debug option to skip_detection_link_training
to debugfs
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds the dma_resv_usage enum and allows us to specify why a
dma_resv object is queried for its containing fences.
Additional to that a dma_resv_usage_rw() helper function is added to aid
retrieving the fences for a read or write userspace submission.
This is then deployed to the different query functions of the dma_resv
object and all of their users. When the write paratermer was previously
true we now use DMA_RESV_USAGE_WRITE and DMA_RESV_USAGE_READ otherwise.
v2: add KERNEL/OTHER in separate patch
v3: some kerneldoc suggestions by Daniel
v4: some more kerneldoc suggestions by Daniel, fix missing cases lost in
the rebase pointed out by Bas.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407085946.744568-2-christian.koenig@amd.com
[Why]
comparing pwm bl values (coverted) with user brightness(converted)
levels in commit_tail leads to continuous setting of backlight via dmub
as they don't to match.
This leads overdrive in queuing of commands to DMCU that sometimes lead
to depending on load on DMCU fw:
"[drm:dc_dmub_srv_wait_idle] *ERROR* Error waiting for DMUB idle: status=3"
[How]
Store last successfully set backlight value and compare with it instead
of pwm reads which is not what we should compare with.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
comparing pwm bl values (coverted) with user brightness(converted)
levels in commit_tail leads to continuous setting of backlight via dmub
as they don't to match.
This leads overdrive in queuing of commands to DMCU that sometimes lead
to depending on load on DMCU fw:
"[drm:dc_dmub_srv_wait_idle] *ERROR* Error waiting for DMUB idle: status=3"
[How]
Store last successfully set backlight value and compare with it instead
of pwm reads which is not what we should compare with.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pointer edid_buf is dereferencing pointer edid before edid is being
null checked. Fix this by assigning edid->raw_edid to edid_buf only if
edid is not NULL, otherwise just NULL.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume we do link detection for all non-MST connectors.
MST is handled separately. However the condition for telling
if connector is on mst branch is not enough for mst hub case.
Link detection for mst branch link leads to mst topology reset.
That causes assert in dc_link_allocate_mst_payload()
[How]
Use link type as indicator for mst link.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ATOMIC and DRIVER log categories do not typically contain per-frame log
messages. This patch re-classifies some messages in amd to chattier
categories to keep ATOMIC/DRIVER quiet.
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
struct drm_display_mode embeds a list head, so overwriting
the full struct with another one will corrupt the list
(if the destination mode is on a list). Use drm_mode_copy()
instead which explicitly preserves the list head of
the destination mode.
Even if we know the destination mode is not on any list
using drm_mode_copy() seems decent as it sets a good
example. Bad examples of not using it might eventually
get copied into code where preserving the list head
actually matters.
Obviously one case not covered here is when the mode
itself is embedded in a larger structure and the whole
structure is copied. But if we are careful when copying
into modes embedded in structures I think we can be a
little more reassured that bogus list heads haven't been
propagated in.
@is_mode_copy@
@@
drm_mode_copy(...)
{
...
}
@depends on !is_mode_copy@
struct drm_display_mode *mode;
expression E, S;
@@
(
- *mode = E
+ drm_mode_copy(mode, &E)
|
- memcpy(mode, E, S)
+ drm_mode_copy(mode, E)
)
@depends on !is_mode_copy@
struct drm_display_mode mode;
expression E;
@@
(
- mode = E
+ drm_mode_copy(&mode, &E)
|
- memcpy(&mode, E, S)
+ drm_mode_copy(&mode, E)
)
@@
struct drm_display_mode *mode;
@@
- &*mode
+ mode
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These on stack copies of the modes appear to be pointless.
Just look at the originals directly.
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: Nikola Cornij <nikola.cornij@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. To leverage and simplify the igt tool. Change the value of
retrain when calling preferred training settings.
Now, writing value to link settings triggers link training immediately.
2. Add dc lock when triggering link training in edp_ilr_write()
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable scatter/gather display for DCN 3.1.6.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The issue only occurs during the GPU reset code path.
We first backup the current state prior to commiting 0 streams
internally from DM to DC. This state backup contains valid link
encoder assignments.
DC will clear the link encoder assignments as part of current state
(but not the backup, since it was a copied before the commit) and
free the extra stream reference it held.
DC requires that the link encoder assignments remain cleared/invalid
prior to commiting. Since the backup still has valid assignments we
call the interface post reset to clear them. This routine also
releases the extra reference that the link encoder interface held -
resulting in a double free (and eventually a NULL pointer dereference).
[How]
We'll have to do a full DC commit anyway after GPU reset because
the stream count previously went to 0.
We don't need to retain the assignment that we had backed up, so
just copy off of the now clean current state assignment after the
reset has occcurred with the new link_enc_cfg_copy() interface.
Fixes: 6d63fcc2a3 ("drm/amd/display: Reset link encoder assignments for GPU reset")
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't fill up the logs with:
[253557.859575] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
[253557.892966] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
[253557.926070] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
[253557.959344] [drm:amdgpu_dm_atomic_check [amdgpu]] DSC precompute is not needed.
which prints many times a second, when the kernel is run with
drm.debug=2.
Instead of DRM_DEBUG_DRIVER(), make it DRM_INFO_ONCE().
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Roman Li <Roman.Li@amd.com>
Cc: Felix Kuehling <felix.kuehling@amd.com>
Cc: Hersen Wu <hersenwu@amd.com>
Cc: Daniel Wheeler <daniel.wheeler@amd.com>
Fixes: 17ce8a6907 ("drm/amd/display: Add dsc pre-validation in atomic check")
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When CONFIG_DRM_AMD_DC_DCN is not set, the function
'dm_helpers_enable_periodic_detection' doesn't have its prototype defined,
causing the following warning:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_helpers.c:805:6:
warning: no previous prototype for function 'dm_helpers_enable_periodic_detection' [-Wmissing-prototypes]
void dm_helpers_enable_periodic_detection(struct dc_context *ctx, bool enable)
^
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_helpers.c:805:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
void dm_helpers_enable_periodic_detection(struct dc_context *ctx, bool enable)
^
static
1 warning generated.
This commit silences this warning by adding a conditional directive
around the mentioned function, and also corrects a small spelling error.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
-----BEGIN PGP SIGNATURE-----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=HuwD
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-02-23' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.18:
UAPI Changes:
Cross-subsystem Changes:
- Split out panel-lvds and lvds dt bindings .
- Put yes/no on/off disabled/enabled strings in linux/string_helpers.h
and use it in drivers and tomoyo.
- Clarify dma_fence_chain and dma_fence_array should never include eachother.
- Flatten chains in syncobj's.
- Don't double add in fbdev/defio when page is already enlisted.
- Don't sort deferred-I/O pages by default in fbdev.
Core Changes:
- Fix missing pm_runtime_put_sync in bridge.
- Set modifier support to only linear fb modifier if drivers don't
advertise support.
- As a result, we remove allow_fb_modifiers.
- Add missing clear for EDID Deep Color Modes in drm_reset_display_info.
- Assorted documentation updates.
- Warn once in drm_clflush if there is no arch support.
- Add missing select for dp helper in drm_panel_edp.
- Assorted small fixes.
- Improve fb-helper's clipping handling.
- Don't dump shmem mmaps in a core dump.
- Add accounting to ttm resource manager, and use it in amdgpu.
- Allow querying the detected eDP panel through debugfs.
- Add helpers for xrgb8888 to 8 and 1 bits gray.
- Improve drm's buddy allocator.
- Add selftests for the buddy allocator.
Driver Changes:
- Add support for nomodeset to a lot of drm drivers.
- Use drm_module_*_driver in a lot of drm drivers.
- Assorted small fixes to bridge/lt9611, v3d, vc4, vmwgfx, mxsfb, nouveau,
bridge/dw-hdmi, panfrost, lima, ingenic, sprd, bridge/anx7625, ti-sn65dsi86.
- Add bridge/it6505.
- Create DP and DVI-I connectors in ast.
- Assorted nouveau backlight fixes.
- Rework amdgpu reset handling.
- Add dt bindings for ingenic,jz4780-dw-hdmi.
- Support reading edid through aux channel in ingenic.
- Add a drm driver for Solomon SSD130x OLED displays.
- Add simple support for sharp LQ140M1JW46.
- Add more panels to nt35560.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/686ec871-e77f-c230-22e5-9e3bb80f064a@linux.intel.com
[Why]
Currently, we don't have code path to release remote dc_sink when unplug
MST hub from the system. After few times hotplug, we hit the limition of
maximum number of remote dc_sink and can't light up new connected monitor
anymore.
[How]
Releasing all remote dc_sink at dm_helpers_dp_mst_stop_top_mgr() was
removed by previous patch. Restore it.
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To move the PSR DPCD caps detection into detect_edp_sink_caps()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Po Ting Chen <robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Turn previously global functions into static functions to avoid
-Wmissing-prototype warnings, such as:
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:20:
warning: no previous prototype for function 'to_dal_irq_source_dcn30'
[-Wmissing-prototypes]
enum dc_irq_source to_dal_irq_source_dcn30(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/irq/dcn30/irq_service_dcn30.c:50:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
enum dc_irq_source to_dal_irq_source_dcn30(
^
static
1 warning generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:6:
warning: no previous prototype for function
'dcn316_clk_mgr_helper_populate_bw_params' [-Wmissing-prototypes]
void dcn316_clk_mgr_helper_populate_bw_params(
^
drivers/gpu/drm/amd/amdgpu/../display/dc/clk_mgr/dcn316/dcn316_clk_mgr.c:488:1:
note: declare 'static' if the function is not intended to be used outside
of this translation unit
void dcn316_clk_mgr_helper_populate_bw_params(
^
static
1 warning generated.
v2: drop is_timing_changed hunk (Alex)
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rather than duplicating the logic in two places,
consolidate the logic in the display manager.
Acked-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the logic for each of these features to make the
code easier to understand and update in the future.
Acked-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add display manager support for DCN 3.1.5.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initialize DMUB for DCN316. Use same funcs as DCN31 for
DCN316.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- set DC version
- add construct/destroy dc clock management function
- register dcn interrupt handler
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Even if PSR is allowed for a present GPU, there might be no eDP link
which supports PSR.
Fixes: 7089784873 ("drm/amdgpu/display: Only set vblank_disable_immediate when PSR is not enabled")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The previous change:
"Add affected crtcs to atomic state for dsc mst unplug"
forces modeset on all added crctc regardless whether timing changed or not.
Per our implementation of dsc we need modeset only if timing changed.
Otherwise dsc can be programmed incorrectly leading to dsc engine hang.
[How]
During atomic_check pre-compute dsc params.
Only set mode_changed if timing is changed.
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
payload and slot number of display on dsc mst hub will be
adjusted when there is change on any display on dsc hub.
to monitor dsc enable/disable, pbn change, we need add log.
[How]
add mst_pbn to dc_dsc_config of dc_crtc_timing.
add dsc, pbn, display name within dc_core_enable_stream,
dc_core_disable_stream, dc_stream_log
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When display topology changed on DSC hub we add all crtcs with dsc support to
atomic state.
Refer to patch:"drm/amd/display: Trigger modesets on MST DSC connectors"
However the original implementation may skip crtc if the topology change
caused by unplug.
That potentially could lead to no-lightup or corruption on DSC hub after
unplug event on one of the connectors.
[How]
Update add_affected_mst_dsc_crtcs() to use old connector state
if new connector state has no crtc (undergoes modeset due to unplug)
Fixes: 44be939ff7 ("drm/amd/display: Trigger modesets on MST DSC connectors")
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
when unplug 1 dp from dsc mst hub, atomic_check new request
dc_state only include info for the unplug dp. this will not
trigger re-compute pbn for displays still connected to hub.
[how] all displays connected to dsc hub are available in
dc->current_state, by comparing dc->current_state and new
request from atomic_chceck, it will provide info of
displays connected to hub and do pbn re-compute.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amd-drm-next-5.18-2022-02-11-1:
amdgpu:
- Clean up of power management code
- Enable freesync video mode by default
- Clean up of RAS code
- Improve VRAM access for debug using SDMA
- Coding style cleanups
- SR-IOV fixes
- More display FP reorg
- TLB flush fixes for Arcuturus, Vega20
- Misc display fixes
- Rework special register access methods for SR-IOV
- DP2 fixes
- DP tunneling fixes
- DSC fixes
- More IP discovery cleanups
- Misc RAS fixes
- Enable both SMU i2c buses where applicable
- s2idle improvements
- DPCS header cleanup
- Add new CAP firmware support for SR-IOV
amdkfd:
- Misc cleanups
- SVM fixes
- CRIU support
- Clean up MQD manager
UAPI:
- Add interface to amdgpu CTX ioctl to request a stable power state for profiling
https://gitlab.freedesktop.org/mesa/drm/-/merge_requests/207
- Add amdkfd support for CRIU
https://github.com/checkpoint-restore/criu/pull/1709
- Remove old unused amdkfd debugger interface
Was only implemented for Kaveri and was only ever used by an old HSA tool that was never open sourced
radeon:
- Fix error handling in radeon_driver_open_kms
- UVD suspend fix
- Misc fixes
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220211220706.5803-1-alexander.deucher@amd.com
[Why]
pflip interrupt order are mapped 1 to 1 to otg id.
e.g. if irq_src=26 corresponds to otg0 then 27->otg1, 28->otg2...
Linux DM registers pflip interrupts per number of crtcs.
In fused pipe case crtc numbers can be less than otg id.
e.g. if one pipe out of 3(otg#0-2) is fused adev->mode_info.num_crtc=2
so DM only registers irq_src 26,27.
This is a bug since if pipe#2 remains unfused DM never gets
otg2 pflip interrupt (irq_src=28)
That may results in gfx failure due to pflip timeout.
[How]
Register pflip interrupts per max num of otg instead of num_crtc
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
First backmerge into drm-misc-next. Required for more helpers backmerged,
and to pull in 5.17 (rc2).
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
DP2 sequence is triggered only if VESA certified cable is detected.
Force DP2 sequence with uncertified cable for testing purpose.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are quite a few spelling mistakes in various function names
and error messages. Fix these.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
- Fix invalid IN_FORMATS blob when plane->format_mod_supported is NULL.
Cross-subsystem Changes:
- Assorted dt bindings updates.
- Fix vga16fb vga checking on x86.
- Fix extra semicolon in rwsem.h's _down_write_nest_lock.
- Assorted small fixes to agp and fbdev drivers.
- Fix oops in creating a udmabuf with 0 pages.
- Hot-unplug firmware fb devices on forced removal
- Reqquest memory region in simplefb and simpledrm, and don't make the ioresource as busy.
Core Changes:
- Mock a drm_plane in drm-plane-helper selftest.
- Assorted bug fixes to device logging, dbi.
- Use DP helper for sink count in mst.
- Assorted documentation fixes.
- Assorted small fixes.
- Move DP headers to drm/dp, and add a drm dp helper module.
- Move the buddy allocator from i915 to common drm.
- Add simple pci and platform module init macros to remove a lot of boilerplate from some drivers.
- Support microsoft extension for HMDs and specialized monitors.
- Improve edid parser's deep color handling.
- Add type 7 timing support to edid parser.
- Add a weak backpointer to the ttm_bo from ttm_resource
- Add 3 eDP panels.
Driver Changes:
- Add support for HDMI and JZ4780 to ingenic.
- Add support for higher DP/eDP bitrates to nouveau.
- Assorted driver fixes to tilcdc, vmwgfx, sn65dsi83, meson, stm, panfrost, v3d, gma500, vc4, virtio, mgag200, ast, radeon, amdgpu, nouveau, various bridge drivers.
- Convert and revert exynos dsi support to bridge driver.
- Add vcc supply regulator support for sn65dsi83.
- More conversion of bridge/chipone-icn6211 to atomic.
- Remove conflicting fb's from stm, and add support for new hw version.
- Add device link in parade-ps8640 to fix suspend/resume.
- Update Boe-tv110c9m init sequence.
- Add wide screen support to AST2600.
- Fix omapdrm implicit dma_buf fencing.
- Add support for multiple overlay planes to vkms.
- Convert bridge/anx7625 to atomic, add HDCP support,
add eld support for audio, and fix HPD.
- Add driver for ChromeOS privacy screen.
- Handover display from firmware to vc4 more gracefully, and support nomodeset.
- Add flexible and ycbcr pixel formats to stm/ltdc.
- Convert exynos mipi dsi to atomic.
- Add initial dual core group GPUs support to panfrost.
- No longer add exclusive fence in amdgpu as shared fence.
- Add CSC and full range supoprt to vc4.
- Shutdown the display on system shutdown and unbind.
- Add Multi-Inno Technology MI0700S4T-6 simple panel.
-----BEGIN PGP SIGNATURE-----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=IMtm
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-01-27' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
[airlied: add two missing Kconfig]
drm-misc-next for v5.18:
UAPI Changes:
- Fix invalid IN_FORMATS blob when plane->format_mod_supported is NULL.
Cross-subsystem Changes:
- Assorted dt bindings updates.
- Fix vga16fb vga checking on x86.
- Fix extra semicolon in rwsem.h's _down_write_nest_lock.
- Assorted small fixes to agp and fbdev drivers.
- Fix oops in creating a udmabuf with 0 pages.
- Hot-unplug firmware fb devices on forced removal
- Reqquest memory region in simplefb and simpledrm, and don't make the ioresource as busy.
Core Changes:
- Mock a drm_plane in drm-plane-helper selftest.
- Assorted bug fixes to device logging, dbi.
- Use DP helper for sink count in mst.
- Assorted documentation fixes.
- Assorted small fixes.
- Move DP headers to drm/dp, and add a drm dp helper module.
- Move the buddy allocator from i915 to common drm.
- Add simple pci and platform module init macros to remove a lot of boilerplate from some drivers.
- Support microsoft extension for HMDs and specialized monitors.
- Improve edid parser's deep color handling.
- Add type 7 timing support to edid parser.
- Add a weak backpointer to the ttm_bo from ttm_resource
- Add 3 eDP panels.
Driver Changes:
- Add support for HDMI and JZ4780 to ingenic.
- Add support for higher DP/eDP bitrates to nouveau.
- Assorted driver fixes to tilcdc, vmwgfx, sn65dsi83, meson, stm, panfrost, v3d, gma500, vc4, virtio, mgag200, ast, radeon, amdgpu, nouveau, various bridge drivers.
- Convert and revert exynos dsi support to bridge driver.
- Add vcc supply regulator support for sn65dsi83.
- More conversion of bridge/chipone-icn6211 to atomic.
- Remove conflicting fb's from stm, and add support for new hw version.
- Add device link in parade-ps8640 to fix suspend/resume.
- Update Boe-tv110c9m init sequence.
- Add wide screen support to AST2600.
- Fix omapdrm implicit dma_buf fencing.
- Add support for multiple overlay planes to vkms.
- Convert bridge/anx7625 to atomic, add HDCP support,
add eld support for audio, and fix HPD.
- Add driver for ChromeOS privacy screen.
- Handover display from firmware to vc4 more gracefully, and support nomodeset.
- Add flexible and ycbcr pixel formats to stm/ltdc.
- Convert exynos mipi dsi to atomic.
- Add initial dual core group GPUs support to panfrost.
- No longer add exclusive fence in amdgpu as shared fence.
- Add CSC and full range supoprt to vc4.
- Shutdown the display on system shutdown and unbind.
- Add Multi-Inno Technology MI0700S4T-6 simple panel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/456a23c6-7324-7543-0c45-751f30ef83f7@linux.intel.com
If only linear modifier is advertised, since there are many drivers that
only linear supported, the DRM core should handle this rather than
open-coding in every driver. However, there are legacy drivers such as
radeon that do not support modifiers but infer the actual layout of the
underlying buffer. Therefore, a new flag fb_modifiers_not_supported is
introduced for these legacy drivers, and allow_fb_modifiers is replaced
with this new flag.
v3:
- change the order as follows:
1. add fb_modifiers_not_supported flag
2. add default modifiers
3. remove allow_fb_modifiers flag
- add a conditional disable in amdgpu_dm_plane_init()
v4:
- modify kernel docs
v5:
- modify kernel docs
Signed-off-by: Tomohito Esaki <etom@igel.co.jp>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128060836.11216-2-etom@igel.co.jp
[Why]
It will build failed with unused variable 'dc' with
'-Werror=unused-variable'enabled when CONFIG_DRM_AMD_DC_DCN
is not defined.
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use IP versions rather than asic_type to differentiate IP version specific features.
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In amdgpu_dm_connector_add_common_modes(), amdgpu_dm_create_common_mode()
is assigned to mode and is passed to drm_mode_probed_add() directly after
that. drm_mode_probed_add() passes &mode->head to list_add_tail(), and
there is a dereference of it in list_add_tail() without recoveries, which
could lead to NULL pointer dereference on failure of
amdgpu_dm_create_common_mode().
Fix this by adding a NULL check of mode.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: e7b07ceef2 ("drm/amd/display: Merge amdgpu_dm_types and amdgpu_dm")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
In order to easily test ilr by immediately reset the preferred training settings,
fix the code to disable skip_immediate_retrain.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Solomon Chiu <solomon.chiu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
OnSetSourceContentAttribute it does not trigger an update for the VSC
with TF change.
[how]
In this call, create a new VSC infoPacket based on the new config, and
allow DisplayTarget decide if an update and pursuant passive flip is
necessary
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Determine if DFP present and the type of downstream device
based on dsc_aux
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the DPCD caps specifies a PSR version newer than PSR_VERSION_1 then
we fallback to using PSR_VERSION_1 in amdgpu_dm_set_psr_caps.
This gets overriden with the raw DPCD value in amdgpu_dm_link_setup_psr,
which can result in DMCUB hanging if we pass in an unsupported PSR
version number.
[How]
Fix the hang by using link->psr_settings.psr_version directly during
amdgpu_dm_link_setup_psr.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prepare for future dm can have different implementation depends on the
return value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Link encoders are created based on its engine ID. The position of a link
encoder in an array could be null since it didn't be allocated. Current
matching logic didn't consider this situation and could get null
encoder.
[How]
To add null encoder check to make the matching logic can go to next to
get a valid one.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, when we're tentatively detecting link configuration under mst
case, we will wrongly notify a none existing stream sink to drm layer.
It's due to we'll call amdgpu_dm_update_connector_after_detect() within
dm_helpers_read_local_edid() to update connector when we're still under
tentative detection procedure.
[How]
dm_helpers_read_local_edid() was designed to do "read" only. Don't
update drm connector status when we're still under detection process.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DCN guard is not necessary for DP2.x relevant logic.
Drop them.
v2: squash in fix for misplaced #endif (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Resource release is needed on the error handling path
to prevent memory leak.
[how]
Fix this by adding kfree on the error handling path.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Yongzhi Liu <lyz_cs@pku.edu.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
- We only ever want seamless boots on eDPs
- The naming and logic did not match the context
[HOW]
- Removed unnecessary if statements
- Renamed power_down_display_on_boot to seamless_boot_edp_requested and
swapped the logic
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jarif Aftab <jaraftab@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Those APIs are used only by legacy ASICs(si/kv). They cannot be
shared by other ASICs. So, we create a new holder for them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display is another client of our power APIs. It's not proper to spike
into power implementation details there.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Freesync Video Mode is a experimental feature previously,
and need to be enabled by kernel parameter. We enable it
by default with removing module paramterter in amdgpu_dm.
v2: squash the patches together
Signed-off-by: Solomon Chiu <solomon.chiu@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function performs a check on the "adev" input parameter, however, it
is used before the check.
Initialize the "dev" variable after the sanity check to avoid a possible
NULL pointer dereference.
Fixes: e27c41d5b0 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Addresses-Coverity-ID: 1493909 ("Null pointer dereference")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When UBSAN is enabled a case is shown on unplugging the display that
this variable hasn't been initialized by `update_dsc_caps`, presumably
when the display was unplugged it wasn't copied from the DPCD.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1956497
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We want to know if new crtc state is enabling MPO configuration before
enabling it.
[how]
Detect if both primary and overlay planes are enabled on the same CRTC.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP will suspend and resume DMCUB. Driver should just wait for DMCUB to
finish the auto load before continuining instead of placing it into
reset, wiping its firmware state and reinitializing.
If we don't let DMCUB fully finish initializing for S0ix then some state
will be lost and screen corruption can occur due to incorrect address
translation.
[How]
Use dmub_srv callbacks to determine in DMCUB is running and wait for
auto-load to complete before continuining.
In S0ix DMCUB will be running and DAL fw so initialize will skip.
In S3 DMCUB will not be running and we will do a full hardware init.
In S3 DMCUB will be running but will not be DAL fw so we will also do
a full hardware init.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Those are not today pulled by the sphinx doc, but better be ready.
Signed-off-by: Yann Dirson <ydirson@free.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the firmware wasn't reset by PSP or HW and is currently running
then the firmware will hang or perform underfined behavior when we
modify its firmware state underneath it.
[How]
Reset DMCUB before setting up cache windows and performing HW init.
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Adding a function to read PSR capabilities
and ALPM capabilities.
Also adding a helper function to validate if
the sink and the driver support PSR SU.
[how]
- isolated all PSR and ALPM reading calls to a separate funciton
- set all required PSR caps
- added a helper function to check if PSR SU is supported by sink
and the driver
Reviewed-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
In order to know the intermediate link rates supported by the eDP
panel and test to select the optimized link rate to save power,
create a new debugfs entry "ilr_setting" for
setting ILR.
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmG2fU0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGC7EH/3R7Rt+OD8Wn8Ss3
w8V+dBxVwa2u2oMTyUHPxaeOXZ7bi38XlUdLFPOK/76bGwO0a5TmYZqsWdRbGyT0
HfcYjHsQ0lbJXk/nh2oM47oJxJXVpThIHXJEk0FZ0Y5t+DYjIYlNHzqZymUyhLem
St74zgWcyT+MXuqY34vB827FJDUnOxhhhi85tObeunaSPAomy9aiYidSC1ARREnz
iz2VUntP/QnRnKVvL2nUZNzcz1xL5vfCRSKsRGRSv3qW1Y/1M71ylt6JVmSftWq+
VmMdFxFhdrb1OK/1ct/930Un/UP2NG9EJsWxote2XYlnVSZHzDqH7lUhbqgdCcLz
1m2tVNY=
=7wRd
-----END PGP SIGNATURE-----
Merge v5.16-rc5 into drm-next
Thomas Zimmermann requested a fixes backmerge, specifically also for
96c5f82ef0 ("drm/vc4: fix error code in vc4_create_object()")
Just a bunch of adjacent changes conflicts, even the big pile of them
in vc4.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This turns previously global functions into static, thus removing
compile-time warnings such as:
warning: no previous prototype for 'get_highest_allowed_voltage_level'
[-Wmissing-prototypes]
742 | unsigned int get_highest_allowed_voltage_level(uint32_t chip_family, uint32_t hw_internal_rev, uint32_t pci_revision_id)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
warning: no previous prototype for 'rv1_vbios_smu_send_msg_with_param'
[-Wmissing-prototypes]
102 | int rv1_vbios_smu_send_msg_with_param(struct clk_mgr_internal *clk_mgr, unsigned int msg_id, unsigned int param)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Changes since v1:
- As suggested by Rodrigo Siqueira:
1. Rewrite function signatures to make them more readable.
2. Get rid of unused functions in order to remove 'defined but not
used' warnings.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This fixes various warnings relating to erroneous docstring syntax, of
which some are listed below:
warning: Function parameter or member 'adev' not described in
'amdgpu_atomfirmware_ras_rom_addr'
...
warning: expecting prototype for amdgpu_atpx_validate_functions().
Prototype was for amdgpu_atpx_validate() instead
...
warning: Excess function parameter 'mem' description in 'amdgpu_preempt_mgr_new'
...
warning: Cannot understand * @kfd_get_cu_occupancy - Collect number of
waves in-flight on this device
...
warning: This comment starts with '/**', but isn't a kernel-doc
comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Thomas Zimmermann
Alex Deucher
Daniel Vetter
Qingqing Zhuo
hersen wu
Aurabindo Pillai
Roman Li
Wayne Lin
Leo Li
David Zhang
pengfuyuan
Leung, Martin
Sung Joon Kim
Dan Carpenter
Bhanuprakash Modem
Dave Airlie
Jiapeng Chong
Christian König
Alex Hung
Alan Liu
Christian König
Paul Cercueil
Shirish S
Haowen Bai
Sean Paul
Ville Syrjälä
Nicholas Kazlauskas
Luben Tuikov
Magali Lemes
Po Ting Chen
Maíra Canal
Prike Liang
Michel Dänzer
Hersen Wu
Lucas De Marchi
Maarten Lankhorst
Fangzhi Zuo
Colin Ian King
Tomohito Esaki
Tim Huang
Tim Huang
Zhou Qingyang
Reza Amini
Ian Chen
Martin Tsai
Wenjing Liu
Yongzhi Liu
Maxime Ripard
Jarif Aftab
Evan Quan
Solomon Chiu
José Expósito
Mario Limonciello
Mikita Lipski
Yann Dirson
Isabella Basso