QCN9274's monitor related rings are initialized properly. Hence enabling
the corresponding ring mask in the hardware params.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-15-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add source buffer ring and destination buffer ring ID for monitor rings.
These IDs are used for ring configuration during initial ring setup.
Since monitor rings are enabled based on the rxdma1_enable flag, enable it
in the hardware param for the QCN9274 version 2 hardware and increase the
destination ring size to handle MSDU data buffers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-2-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of firmware assert snapshot of firmware memory is essential for
debugging. Add firmware coredump collection support for PCI bus.
Collect RDDM and firmware paging dumps from MHI and pack them in TLV
format and also pack various memory shared during QMI phase in separate
TLVs. Add necessary header and share the dumps to user space using dev
coredump framework. Coredump collection is disabled by default and can
be enabled using menuconfig. Dump collected for a radio is 55 MB
approximately.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.2.1-00201-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240717085604.4131642-1-quic_ssreeela@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
mwifiex has recently started to see active development which is good
news. rtw89 is also under active development and got several new
features. Otherwise not really anything out of ordinary.
We have one conflict in ath12k but that's easy to fix:
https://lore.kernel.org/all/20240808104348.6846e064@canb.auug.org.au/
Major changes:
mwifiex
* support for up to ten Authentication and Key Management (AKM) suites
* host MAC Sublayer Management Entity (MLME) client and AP mode support
* WPA-PSK-SHA256 AKM suite support
rtw88
* improve USB performance by aggregation
rtw89
* Wi-Fi 6 chip RTL8852BE-VT support
* WoWLAN net-detect support
* hardware encryption in unicast management frames support
* hardware rfkill support
ath12k
* DebugFS support for transmit DE stats
* Make ASPM support hardware-dependent
iwlwifi
* channel puncturing for US/CAN from UEFI
* bump FW API to 93 for BZ/SC devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmbYfCARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt+Qwf/X9oQ4sf8jV6eOV7EhoWhIHnQadvo5YBZ
ulBm8In0QGjEOVWkI7kXGabKP5jhne2lVIyP1eFfP2/td/A2yDWIuEeBfDQD6f4K
aiUGAa1gs4ZtGKJBniw/ukflSqJlR99N2qBO5T/smDm3Nw/aC522SO7BoLTpoJDQ
SuW4atFHMShXYf/vIrAA2yB9ok2yw/QM+27M9qjj6D7zzqsQxDl9wKGW+2v8KiSa
rXXbfnwfaQP21CYv5xYbEPACSRSV5Dr0TNopivWYxmm9svjLzwFN2JM2fHPxBEDh
wP6Ojp+Z32c1VbQtclLrwIQdlZ5yhU5MEDlVg5VLym9F83hv+oXTbA==
=lgVx
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
pull-request: wireless-next-2024-09-04
here's a pull request to net-next tree, more info below. Please let me know if
there are any problems.
====================
Conflicts:
drivers/net/wireless/ath/ath12k/hw.c
38055789d1 ("wifi: ath12k: use 128 bytes aligned iova in transmit path for WCN7850")
8be12629b4 ("wifi: ath12k: restore ASPM for supported hardwares only")
https://lore.kernel.org/87msldyj97.fsf@kernel.org
Link: https://patch.msgid.link/20240904153205.64C11C4CEC2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During PCI based hardware device start up, ASPM is disabled for all. And
once firmware is ready, it is restored back. However, not all hardwares
(for example QCN9274) supports ASPM. Hence there is a need to conditionally
restore ASPM back. Or else, for such hardwares, issue can be seen during
sending and receiving packets.
Introduce a new hardware param supports_aspm which identifies whether a
given hardware supports ASPM or not and then accordingly restore it.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240709055817.3371406-1-quic_adisi@quicinc.com
In transmit path, it is likely that the iova is not aligned to PCIe TLP
max payload size, which is 128 for WCN7850. Normally in such cases hardware
is expected to split the packet into several parts in a manner such that
they, other than the first one, have aligned iova. However due to hardware
limitations, WCN7850 does not behave like that properly with some specific
unaligned iova in transmit path. This easily results in target hang in a
KPI transmit test: packet send/receive failure, WMI command send timeout
etc. Also fatal error seen in PCIe level:
...
Capabilities: ...
...
DevSta: ... FatalErr+ ...
...
...
Work around this by manually moving/reallocating payload buffer such that
we can map it to a 128 bytes aligned iova. The moving requires sufficient
head room or tail room in skb: for the former we can do ourselves a favor
by asking some extra bytes when registering with mac80211, while for the
latter we can do nothing.
Moving/reallocating buffer consumes additional CPU cycles, but the good news
is that an aligned iova increases PCIe efficiency. In my tests on some X86
platforms the KPI results are almost consistent.
Since this is seen only with WCN7850, add a new hardware parameter to
differentiate from others.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Cc: <stable@vger.kernel.org>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240715023814.20242-1-quic_bqiang@quicinc.com
The monitor ring and the reo reinject ring share the same ring mask index.
When the driver receives an interrupt for the reo reinject ring, the
monitor ring is also processed, leading to invalid memory access. Since
monitor support is not yet enabled in ath12k, the ring mask for the monitor
ring should be removed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00209-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240520070045.631029-3-quic_ppranees@quicinc.com
Add support for dynamic VLAN. VLAN group traffic is encapsulated and
encrypted in mac80211 and driver needs to set flags for the VLAN group
traffic to skip hardware encapsulation and encryption.
VLAN group traffic utilizes ext MSDU and HTT Metadata to set
encapsulation type to RAW and encryption type to OPEN in order to
inform firmware to skip hardware encapsulation and encryption.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240515192830.995013-1-quic_msinada@quicinc.com
We observe intermittent ping failures from the access point (AP) to
station (STA) in any mode (AP-STA or Mesh) configured. Specifically,
the transmission completion status is not received at tx completion
ring id 4 (WBM2SW ring4) for the packets transmitted via TCL DATA
ring id 3. This prevents freeing up tx descriptors and leads
to buffer exhaustion.
Currently, during initialization of the WBM2SW ring, we are directly
mapping the ring number to the ring mask to obtain the ring mask
group index. This approach is causing setup failures for WBM2SW
ring 4. Similarly, during runtime, when receiving incoming
transmission completion status, the validation of the ring number by
mapping the interrupted ring mask. This is resulting in
validation failure. Thereby preventing entry into the completion
handler ath12k_dp_tx_completion_handler().
The existing design assumed that the ring numbers would always be
sequential and could be directly mapped with the ring mask. However,
this assumption does not hold true for WBM2SW ring 4. Therefore,
modify the design such that, instead of mapping the ring number,
the ring ID is mapped with the ring mask.
According to this design:
1. During initialization of the WBM2SW ring, mapping the ring ID
to the ring mask will ensure obtaining the correct ring mask group
ID.
2. During runtime, validating the interrupted ring mask group ID
within the transmission completion group is sufficient. This
approach allows the ring ID to be derived from the interrupted ring
mask and enables entry into the completion handler.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240510070427.206152-1-quic_nithp@quicinc.com
Parse SMPS configuration from IEs and configure. Without this,
SMPS is not enabled for 6 GHz band. This is disabled for
WCN7850 as hardware does not support it.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508173655.22191-7-quic_pradeepc@quicinc.com
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable
TAS read the tables from ACPI and send them to the firmware using
WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI
event callback so that ACPI can notify ath12k to get the updated SAR power
table and sends it to the firmware when the device state is changed.
ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid
field. Most likely QCN9274 will never support ACPI as the chip is not used in
laptops.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
Now that all things are ready, enable supports_suspend to
make suspend/resume work for WCN7850. Don't touch other
chips because they don't support suspend.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-11-quic_bqiang@quicinc.com
Now that all the necessary pieces are implemented we can enable P2P
support for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-12-quic_kangyang@quicinc.com
To reduce power consumption enable 802.11 power save mode in
station mode. This allows both radio and CPU to sleep more.
Only enable the mode on WCN7850, other chips don't support it
for now.
To test that power save mode is running, run below command and
check there is no NULL Data frame seen by a sniffer:
iw dev <inf> set power_save off
And run below command, then check there is a NULL Data frame
in sniffer:
iw dev <inf> set power_save on
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240201035830.2534-1-quic_bqiang@quicinc.com
QCN9274 can support single-PHY or split-PHY architecture. Currently,
only the single-PHY architecture is supported in ath12k.
The split-PHY QCN9274 requires different AMSS firmware binary
"amss_dualmac.bin".
Hence, add support to read board id from OTP. Based on board id
decide whether single-mac / dual-mac firmware needs to be downloaded
to the target. Also, update HW param max_radios to support split-PHY
in QCN9274.
Also, add new Firmware IE for firmware_N.bin
"ATH11K_FW_IE_AMSS_DUALMAC_IMAGE" to support dualmac QCN9274.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-13-quic_rajkbhag@quicinc.com
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
The hardware param hal_desc_sz value cannot be constant for the same
hardware. It depends on the size of rx_desc structure which may
change based on firmware capability to support word mask subscription.
Hence, remove hal_desc_sz from hardware param and add hal_rx_ops
to get the size of rx_desc in run time.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-9-quic_rajkbhag@quicinc.com
Currently, QMI MLO host capability parameters are specific to the WCN7850
platform. To make use of this helper function across all the platforms,
move the platform specific MLO capability parameter to the HW param
configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240113001659.1022465-2-quic_periyasa@quicinc.com
For AP mode, the peer is created earlier in ath12k_mac_op_add_interface() but
ath12k_mac_op_assign_vif_chanctx() will try to create peer again. Then an
error will return which makes AP mode startup fail.
Kernel log:
[ 5017.665006] ath12k_pci 0000:04:00.0: failed to create peer after vdev start delay: -22
wpa_supplicant log:
Failed to set beacon parameters
Interface initialization failed
wls1: interface state UNINITIALIZED->DISABLED
wls1: AP-DISABLED
wls1: Unable to setup interface.
Failed to initialize AP interface
wls1: interface state DISABLED->DISABLED
wls1: AP-DISABLED
So fix this check and enable AP mode for WCN7850, as now AP mode works normally.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121022459.17209-1-quic_kangyang@quicinc.com
Currently QCN9274 supports only AP and station interface modes.
Add interface type mesh to ath12k_hw_params for
QCN9274 to provide support for mesh mode as well.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231013070007.25597-2-quic_rgnanase@quicinc.com
RDDM is Ram Dump Debug Module which is used to debug issues when the
firmware encounters an error. The rddm_size is needed by the firmware
while MHI goes to the RDDM state. Provide the size to MHI subsystem so
that the firmware restart works when the firmware crashes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230721055305.20420-2-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
The PCIe PERST pin is currently pulled down on WCN7850 and it causes
some power leakage.
Fix it by notifying firmware not to pull down PCIe PERST pin in QMI
message for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230404032057.3236122-3-quic_cjhuang@quicinc.com
Currently the CNSS (Connectivity Subsystem) QMI feature is assigned to
qmi_wlanfw_host_cap_req_msg_v01 request directly, this prevents chip-specific
CNSS features from being added easily.
Solve this by adding a new field qmi_cnss_feature_bitmap to hw_params so
chip-specific CNSS features can be assigned to this field and later assigned to
qmi_wlanfw_host_cap_req_msg_v01 request.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230404032057.3236122-2-quic_cjhuang@quicinc.com
To reduce power consumption, change idle_ps to true to enable
Idle Mode Power Save (IMPS) for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230317062533.18240-1-quic_bqiang@quicinc.com
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
P Praneesh
Sowmiya Sree Elavalagan
Jakub Kicinski
Aditya Kumar Singh
Baochen Qiang
Muna Sinada
Nithyanantham Paramasivam
Pradeep Kumar Chitrapu
Jeff Johnson
Lingbo Kong
Kang Yang
Ganesh Babu Jothiram
Raj Kumar Bhagat
Karthikeyan Periyasamy
Ramya Gnanasekar
Wen Gong
Carl Huang
Kalle Valo