The single split-phy PCI device can perform multi-link operation (MLO)
within its own radio, and the MLO-supporting firmware also supports MLO
for split-phy PCI devices.
Therefore, enable MLO for the single split-phy PCI device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When multi-link operation(MLO) is enabled through follow-up patches in
the single split-phy device, the firmware expects hardware links
(hw_links) information from the driver.
If driver does not send WMI multi-link setup and ready command to the
firmware during MLO setup for single split-phy device, the firmware will
be unaware of the hw_links component of the multi-link operation. This may
lead to firmware assert during multi-link association.
Therefore, enable WMI setup, ready and teardown commands for single
split-phy PCI device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250207050327.360987-2-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For MLO netdevice, the broadcast frame should be transmitted with the
same sequence number on all the links.
Per IEEE 802.11be-2024 section 10.3.2.14.2 "Transmitter requirements",
An AP MLD shall use SNS11 in Table 10-5 (Transmitter sequence number
spaces) maintained by the MLD to determine the sequence number of a
group addressed data frame that is transmitted by an AP affiliated
with the AP MLD so that the same group addressed Data frame
transmitted over multiple links by the AP MLD uses the same
sequence number for transmission on each link.
Currently the MLO multicast handling is done in the mac80211 layer.
Enable support for handling MLO Multicast in the driver to update the
hardware descriptors in a custom way to handle the multicast frames.
Firmware expects the MLO multicast frames to the submitted to the
hardware with special vdev_id (actual vdev_id + 128) to recognize it as
a host inspected frame to avoid using the reinjected path and it also
uses the multicast global sequence number (GSN) provided by the host
in the HTT metadata to process and transmit it with the same sequence
number.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250203212647.2694566-3-quic_bmahalin@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, peer rate table information involves complex computation for
the rate index to update the rate table. To simplify this process, avoid
the rate index calculation by defining the rate table with bandwidth, GI,
NSS, MCS. Therefore, update the rate information based on the bandwidth,
GI, NSS and MCS information from the TLV data of monitor status Rx path.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-9-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, EHT MCS information is not populated. Therefore, add the EHT
MCS counter array to the peer rate statistics and update the EHT MCS
statistics from the status TLV data in the monitor Rx path. In the future,
this information will be used in the peer extended Rx statistics dump.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Balamurugan Mahalingam <quic_bmahalin@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250206013854.174765-8-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This adds support for reporting to the kernel the average rssi. This is
done the same way as it was done in ath11k. A simple ewma (with the same
parameters) is updated with each rssi update.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250201211301.357985-1-nico.escande@gmail.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Host receives four Transmit Power Control(TPC) events from firmware on
sending TPC request. Fixed param TLV is present as part of all event to
indicate the event count and end of event. TPC config parameters along
with regulatory power array comes as first event. Rates array comes as
second and third event as it cannot be packed in single event.
Conformance Test Limit (CTL) power array comes as the fourth event.
Firmware packs different sets of array params which includes array
length and type inside master TLV as different subtlvs. And the actual
content of array is packed one after the other inside a separate TLV as
single buffer.
Parse various events and save it in local structures. Create tpc_stats
file using debugfs to store these local structures. Create function to
handle TPC stats read to relay the information to the user.
Command usage:
cat > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/tpc_stats
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250130061104.962124-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support reading variant from ACPI board data
filename extension for downloading board data file.
To address this issue, obtain the string of the ACPI data filename
extension and use it as part of the string to search for the board data
file from board-2.bin.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-5-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the timing for accessing the ACPI table is inappropriate.
Due to special ACPI requirements, the ACPI table must be obtained before
downloading the board data file. Therefore, adjust the timing for accessing
the ACPI table accordingly.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k does not support enable or disable specific features by
ACPI bitflag.
To address this issue, obtain the ACPI bitflag value and use it to
selectively enable or disable specific features.
This patch will not affect QCN9274, because only WCN7850 supports ACPI.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250113074810.29729-3-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of MHI error a reset work will be queued which will try
napi_disable() after napi_synchronize().
As the napi will be only enabled after qmi_firmware_ready event,
trying napi_synchronize() before napi_enable() will result in
indefinite sleep in case of a firmware crash in QMI init sequence.
To avoid this, introduce napi_enabled flag to check if napi is enabled
or not before calling napi_synchronize().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124090058.3194299-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, when the driver receives a channel switch count WMI event from
the firmware with a count greater than 1, it calls
ieee80211_beacon_update_cntdwn(). If the beacon transmission fails, the
event will be received again with the previous count value. In this
scenario, the host decrements the mac80211 counter again, causing it to
move ahead of the firmware counter. Ultimately, when the firmware count
reaches 1, the mac80211 counter will reach zero, triggering a
WARN_ON_ONCE(). Therefore, there is a need to check the count value in the
event.
Hence to fix this, maintain the current ongoing counter in arvif. If the
count in the event does not match the expected value, silently discard the
event.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-4-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
During monitor destination ring back-pressure, hardware failed to send
HAL_RX_PPDU_END_STATUS_DONE TLV. But driver uses this TLV as a delimiter
to complete one PPDU worth of data parsing. This causes driver to overwrite
the existing PPDU information with the new PPDU information.
Fix it by recording the end reason which is provided under each buffer's
descriptor in skb->cb and uses it while parsing TLV tags to mark the PPDU
end delimiter.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Link: https://patch.msgid.link/20241223060132.3506372-14-quic_ppranees@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the signal strength of "iw dev xxx station dump" always show an
invalid value.
This is because signal strength is only set in ath12k_mgmt_rx_event()
function, and not set for received data packet. So, change to get signal
from firmware and report to mac80211.
After that, "iw dev xxx station dump" show the correct signal strength.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 36 ms
rx bytes: 61571
rx packets: 336
tx bytes: 28204
tx packets: 205
tx retries: 49
tx failed: 0
beacon loss: 0
beacon rx: 83
rx drop misc: 66
signal: -24 dBm
beacon signal avg: -22 dBm
For WCN7850, the firmware supports db2dbm, so not need to add noise floor.
For QCN9274, the firmware not support db2dbm, so need to add noise floor.
This patch affects the station mode of WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Link: https://patch.msgid.link/20250115063537.35797-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the transmit rate of "iw dev xxx station dump" command
always show an invalid value.
To address this issue, ath12k parse the info of transmit complete
report from firmware and indicate the transmit rate to mac80211.
This patch affects the station mode of WCN7850 and QCN9274.
After that, "iw dev xxx station dump" show the correct transmit rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 872 ms
rx bytes: 219111
rx packets: 1133
tx bytes: 53767
tx packets: 462
tx retries: 51
tx failed: 0
beacon loss: 0
beacon rx: 403
rx drop misc: 74
signal: -95 dBm
beacon signal avg: -18 dBm
tx bitrate: 1441.1 MBit/s 80MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to process factory test mode commands(FTM) for calibration.
By default firmware start with MISSION mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.
All ath12k test mode interface related commands specified in enum
ath_tm_cmd.
When start command ATH_TM_CMD_TESTMODE_START is received, ar state
is set to test Mode and FTM daemon sends test mode command to wifi
driver via cfg80211. Wifi driver sends these command to firmware as
wmi events. If it is segmented commands it will be broken down into
multiple segments and encoded with TLV header else it is sent to
firmware as it is.
Firmware response via UTF events, wifi driver creates skb and send
to cfg80211, cfg80211 sends firmware response to FTM daemon via
netlink message.
Command to boot in ftm mode
insmod ath12k ftm_mode=1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the ath12k_get_num_hw() helper function takes the device handle
as an argument. Here, the number of hardware is retrieved from the group
handle. Demanding the device handle from the caller is unnecessary since
in some cases the group handle is already available. Additionally, there
is no longer a need for multiple indirections to get the number of
hardware. Therefore, remove this helper function and directly use
ag->num_hw. This change also fixes the below Smatch static checker
warning.
Smatch warning:
ath12k_mac_destroy() error: we previously assumed 'ab' could be null
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/ath12k/3e705de0-67d1-4437-97ff-4828d83ae2af@stanley.mountain/
Closes: https://scan7.scan.coverity.com/#/project-view/52682/11354?selectedIssue=1602340
Fixes: a343d97f27 ("wifi: ath12k: move struct ath12k_hw from per device to group")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250112071630.4059410-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw get helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle
to the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw set helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle to
the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Rename the flag ATH12K_CAC_RUNNING to ATH12K_FLAG_CAC_RUNNING to correct
the naming inconsistency in the enum ath12k_dev_flags.
No functionality changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218-ath12k_mlo_dfs-v1-1-058e783bcfc7@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, unused fields are present in the Rx peer statistics
structure. These fields are already present in the same structure
under the ath12k_rx_peer_rate_stats container structure. Therefore,
remove the unused fields from the Rx peer statistics structure.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241217084511.2981515-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Now everything in ath12k is in place and we can enable Multi-Link Operation
(MLO) in the driver. For now it's only enabled for QCN9274 with firmware having
ATH12K_FW_FEATURE_MLO feature bit set.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, in the QMI host capability, the device index, the number of local
links, and the corresponding hardware link IDs are sent. The hardware link ID
assignment is based on the local variable `hw_link_id`, which starts from 0 and
ranges up to `num_local_links` in the device. Starting from 0 is not ideal
because it can result in the same link ID being assigned to different devices
in certain scenarios (e.g., split MAC). Additionally, for multi link
operations the firmware expects the hardware link IDs in the same order as the
Wireless Serial Interface (WSI) connection.
Hence, for MLO to function seamlessly, the hardware link IDs across devices
need to be unique and should follow the order of the WSI connection. To address
this, a previous change read the WSI index from the Device Tree (DT) and stored
it. Use this WSI index to determine the starting hardware link IDs for each
device, ensuring uniqueness and correct order across all devices.
While at it, add debug prints to clearly show the MLO capability advertisement
sent during QMI host capability exchange.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the hardware scan is initiated in the driver on scan link (15).
After mapping to the appropriate radio based on the scan frequency, the vdev is
created and the scan begins. However, the vdev is only deleted when channel
assignment is about to occur after the scan. Additionally, it is also deleted
if a new scan is requested on the same interface but the underlying radio
differs in the new request.
This imbalance leads to various hardware scan issues, especially when a non-MLO
and MLO combination exists. In such cases, the latter tries to skip the scan
and proceed with channel assignment while the former is still scanning, causing
a firmware assert.
To address this issue, symmetrize the scan vdev creation and deletion during
hardware scan operations. This means creating a vdev when the scan starts and
deleting it once the scan is completed or aborted.
While at this, add a few debug prints in scan handling and a few empty lines
for better code read.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, radio stores the low frequency and high frequency information as
separate variables. However, cfg80211 already provides a suitable data
structure struct wiphy_radio_freq_range to store this information efficiently.
Additionally, for multi radio per wiphy infrastructure, this frequency range
information is essential. In future patches using struct wiphy_radio_freq_range
makes the code simpler.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, partner device buffer is not handled in the receive data path. In
Multi-Link Operation, the partner device buffer is reported to the primary
upper MAC rings. Therefore, add partner device buffer processing in the REO and
Exception ring handler.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, all the rx processing treats the hardware link id as the MAC id.
The HW link id is a unique identifier for all hardware links participating in
the multi link group. Therefore, the current MAC id derivation is insufficient
to process the partner rx buffer in the Multi-Link Operation. So derive the
MAC id from the HW link id and implementing this change in rx processing will
enable the scaling of partner buffer processing in Multi-Link Operation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241209185421.376381-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of multi device group abstraction, host has to exchange the multi-link
operation commands such as setup and ready to firmware before registering the
device group to mac80211.
The multi-link operation commands - setup, ready and teardown are necessary for
many commands such as WMI_PEER_ASSOC_CMD, WMI_BCN_TMPL_CMD in case of
multi-link interfaces.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
To enable Multi-Link Operation (MLO), QCN9274 firmware requests MLO global
memory (MLO_GLOBAL_MEM_REGION_TYPE). This memory region is shared across all
the firmware (SoC) that are participation in the MLO.
Hence, add support to allocate and free MLO global memory region. Allocate one
MLO global memory per struct ath12k_hw_group and assign the same memory to all
firmware in the same struct ath12k_hw_group. WCN7850 firmware does not request
this memory type, therefore this change will have no impact on WCN7850 device.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, a single device is part of the device group abstraction. However,
for multi-link operations, multiple devices need to be combined. This
multi-device grouping is done via WSI (WLAN Serial Interface), which is
described in the Device Tree. Information about different WSI groups and the
number of devices involved in each group can be parsed from the Device Tree.
Add changes to parse the Device Tree and determine WSI information, such as the
different WSI groups and the number of devices per WSI group. Assign WSI index
zero to the WSI controller device (to synchronize the clock among the devices
within the WSI group), and increment the WSI index of each device in the order
of the WSI connection.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, during mac80211 allocate and register single device is
considered for the registration. But, in future, during multi device
group abstraction is introduced, all the devices has to be combined
together as a single abstraction and then hardware should be allocated.
All the devices in the group should be combined together only if it
supports inter device mlo capability. The decision of whether to combine
the devices or not can be based on the mlo capability flag in
ath12k_hw_group.
By default, mlo_capable flag in the group would be set as false. During
QMI PHY capability exchange, only when we have more than one chip in the
group or if one chip, then that chip supports inter MLO, then mlo_capable
flag in the group will be enabled.
Add changes to introduce mlo_capable flag for device group and refactor
ath12k_mac_hw_allocate() api based on device group (ag) rather than
device (ab).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, hardware abstractions (ah) of different radio bands are tightly
coupled to a single device (ab). But, with hardware device group abstraction
(ag), multiple radios across different devices in a group can form different
combinations of hardware abstractions (ah) within the group. Hence, the mapping
between ah to ab can be removed and instead it can be mapped with struct
ath12k_hw_group (ag).
Current mapping between struct ath12k_hw (ah), struct ath12k_base (ab) and struct
ath12k_hw_group (ag):
+------------------------------------------------+
| +-------------------------------------+ |
| | +---------------+ +---------------+ | |
| | |ath12k_hw (ah) | |ath12k_hw (ah) | | |
| | +---------------+ +---------------+ | |
| | | |
| | +-----------+ | +-----------+ | |
| | | ar (2GHz) | | | ar (5GHz) | | |
| | +-----------+ | +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------+
After hardware device group abstraction moving ah array out of ab to ag:
+----------------------------------------------+
| +---------------+ +---------------+ |
| |ath12k_hw (ah) | |ath12k_hw (ah) | |
| +---------------+ +---------------+ |
| +-------------------------------------+ |
| | +-----------+ +-----------+ | |
| | | ar (2GHz) | | ar (5GHz) | | |
| | +-----------+ +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+----------------------------------------------+
This decoupling of struct ath12k_hw (ah) from struct ath12k_base (ab) and
mapping it to struct ath12k_hw_group (ag) will help in forming different
combinations of multi-link devices.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, mac allocate/register and core_pdev_create are initiated immediately
when QMI firmware ready event is received for a particular device. With
hardware device group abstraction, QMI firmware ready event can be received
simultaneously for different devices in the group and so, it should not be
registered immediately rather it has to be deferred until all devices in the
group has received QMI firmware ready.
To handle this, refactor the code of core start to have registering within
ath12k_core_hw_group_start() and unregistering in ath12k_core_hw_group_stop().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, single device is probed, and once firmware is ready, the device
is registered to mac80211. For Multi-Link Operation, different bands of
different devices or same device are part of a single wiphy and for
this, hardware device group abstraction is needed.
Hardware device group abstraction - when there are multiple devices (with
single radio or dual radio) that are connected by any means of interface
for communicating between them, then these devices can be combined
together as a single group using a group id to form a group abstraction
and register to mac80211.
The grouping information of multiple devices would be based on device tree
during device probe (will be implemented in future patches). If no such
information is available, then a single device will be part of group abstraction
and registered to mac80211, else multiple devices advertised in device tree are
combined and then registered to mac80211.
For device group abstraction, a base structure ath12k_hw_group (ag) and the
helpers are implemented. These helpers are used during device probe and mapping
the group to the devices involved.
An illustration of how multiple devices might be combined together in
future based on group id:
+------------------------------------------------------------------------+
| +-------------------------------------+ +-------------------+ |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | | ar (2GHz) | | | | ar (5GHz) | | | | ar (6GHz) | | |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | ath12k_base (ab) | | ath12k_base (ab) | |
| | (Dual band device) | | | |
| +-------------------------------------+ +-------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------------------------------+
In the above representation, two devices are combined into single group
based on group id.
Add base code changes where single device would be part of a group with an
invalid group id forming an group abstraction. Multi device grouping will
be introduced in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the mlo_capable_flags in ath12k_base is used to indicate whether
the chip supports inter (QCN9274) or intra (WCN7850) chip MLO. However, it’s
possible that the chip supports neither, especially with older firmware
versions. Additionally, if intra chip MLO is not supported, inter chip MLO will
also be non-functional. Therefore, having two separate flags for this is
unnecessary.
Therefore, rename this flag to single_chip_mlo_supp. At the same time convert
it into a bool data type. Also, get rid of the enums defined earlier.
For the QCN9274 family of chipsets, this will be set only when firmware
advertises the support during the QMI exchange.
For the WCN7850 family of chipsets, since the event is not supported,
assumption is made that single chip MLO is supported.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When hardware device group abstraction is introduced, the QMI firmware ready
event of different devices in a group can be received simultaneously. To
indicate the firmware ready event is completed for a particular device in a
group set a flag (ATH12K_FLAG_QMI_FW_READY_COMPLETE). This helps the upcoming
hardware recovery implementation for hardware device group abstraction.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-5-kvalo@kernel.org
Currently, one or more struct ath12k_hw is part of device (struct ath12k_base)
but in future, ath12k_hw would be part of device group (struct
ath12k_hw_group). Hence, num_hw under device would be moved to device group.
To facilitate above transition, add helper ath12k_get_num_hw() to get the
number of radios per device. In future, this helper will return the number of
radios in a device group.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-4-kvalo@kernel.org
Currently, one or more ath12k_hw is part of a device (struct ath12k_base) but
in future, it would be part of device group abstraction (struct
ath12k_hw_group), i.e., when multiple radios (ar) across different devices can
be combined together in a device group (struct ath12k_hw_group).
In order to facilitate the above transition, introduce helpers
ath12k_ab_to_ah() and ath12k_ab_set_ah() to get and set values of ath12k_hw
respectively.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-3-kvalo@kernel.org
When a scan request is received, driver selects a link id for which the arvif
can be mapped. Same link is also used for getting the link conf address.
Currently, we return 0 as link id for a non ML vif, which is correct since that
is the default link id. Also when any of the link vif is active and the scan
request is for a channel in the active link we return its link id. But, when we
don't hit both of the above cases (i.e not a ML vif or no active link vif for
the channel is present) we currently return 0 as the link id.
Bu the problemis that this might not work out always, eg., when only one link
(eg. linkid = 1) is added to vif, then we won't find any link conf for link id
0 in the vif resulting in scan failure. During AP bringup, such scan failure
causes bringup issues. Hence avoid sending link id 0 as default. Rather use a
default link for scan and default link address for the same. This scan vdev
will either be deleted if another scan is requested on same vif or when AP is
broughtup on same link or during interface cleanup.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-7-kvalo@kernel.org
For a frame transmission for an ML vif, mac80211 mentions transmit link id in
the tx control info. Use it to convert the RA/TA to the corresponding link sta
and link vif address before enqueueing the frame for transmission.
For 802.3 data frames, always enqueue the frame on the primary (assoc) link id.
Firmware does the link selection, builds 802.11 header and therefore the address
translation too.
Also ensure right link vif is used for WMI based management transmission and
add comments to document when RCU read lock is held.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-3-kvalo@kernel.org
To simplify locking for the next patches convert struct
ath12k::wmi_mgmt_tx_work to use wiphy_work. After this
ath12k_mgmt_over_wmi_tx_work() is called with wiphy_lock() taken. In
ath12k_core_suspend() we need to take wiphy_lock() because
ath12k_mac_wait_tx_complete() requires it.
Also add lockdep_assert_wiphy() to document when wiphy_lock() is held.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-2-kvalo@kernel.org
Add changes to handle multi-link station state change with proper
link handling and add code changes for ML peer creation, peer deletion.
In ath12k_mac_assign_link_sta() initialise all arsta fields first and only then
call rcu_assign_pointer(). This is to make sure that readers don't have access
to arsta which is still modified.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-2-kvalo@kernel.org
Add changes to send MLO peer assoc command with partner link details and
primary umac details.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-9-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Add helper functions for multi link peer addition and deletion. And add address
validation to ensure we are not creating link peers (belonging to different
clients) with same MLD address. To aid in this validation for faster lookup,
add a new list of ML peers to struct ath12k_hw::ml_peers and use the same for
parsing for the above address validation use cases.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
In the following patch we need to use ath12k_warn() but don't easily have
access to struct ath12k_base (ab) but do have access to struct ath12k_hw (ah).
So add a new warning helper ath12_hw_warn() which takes the latter but the log
output is still identical but uses the struct device pointer stored to struct
ath12k_hw.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-5-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Refactor ath12k_mac_op_sta_state(), with generic wrappers which can be used for
both multi link stations and non-ML stations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Aaradhana Sahu
Balamurugan Mahalingam
Karthikeyan Periyasamy
Nicolas Escande
Sowmiya Sree Elavalagan
Lingbo Kong
Avula Sri Charan
Aditya Kumar Singh
P Praneesh
Ramya Gnanasekar
Rameshkumar Sundaram
Raj Kumar Bhagat
Sriram R
Kalle Valo