First get the devtype_data then check quirks.
Fixes: bbdffb3414 ("can: rockchip_canfd: add quirk for broken CAN-FD support")
Signed-off-by: Weizhao Ouyang <o451686892@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250324114416.10160-1-o451686892@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The rockchip_canfd driver doesn't make use of the TXE FIFO.
Although the comment states that the TXE FIFO is setup, it's actually
a setup of the RX FIFO. The regular setup of the RX FIFO follows.
Remove the duplicated setup of the RX FIFO.
Fixes: ff60bfbaf6 ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Link: https://patch.msgid.link/20250219-rk3568-canfd-v1-1-453869358c72@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver contains workarounds for some of the rk3568v2 errata. Add
ethtool-based statistics ("ethtool -S") to track how often an erratum
workaround was needed.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-15-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tests show that sometimes both CAN bus error counters read 0x0, even
if the controller is in warning mode
(RKCANFD_REG_STATE_ERROR_WARNING_STATE in RKCANFD_REG_STATE
set).
To work around this issue, if both error counters read from hardware
are 0x0, use the structure priv->bec, otherwise save the read value in
priv->bec.
In rkcanfd_handle_rx_int_one() decrement the priv->bec.rxerr for
successfully RX'ed CAN frames.
In rkcanfd_handle_tx_done_one() decrement the priv->bec.txerr for
successfully TX'ed CAN frames.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-14-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The IP core has a TX event FIFO. In other IP cores, this type of FIFO
usually contains the events that a CAN frame has been successfully
sent. However, the IP core on the rk3568v2 the FIFO also holds events
of unsuccessful transmission attempts.
It turned out that the best way to work around this problem is to set
the IP core to self-receive mode (RXSTX), filter out the self-received
frames and insert them into the complete TX path.
Add a pair new functions to check if 2 struct canfd_frame are equal.
The 1st checks if the header of the CAN frames are equal, the 2nd
checks if the data portion are equal:
- rkcanfd_can_frame_header_equal()
- rkcanfd_can_frame_data_equal()
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-11-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tests on the rk3568v2 and rk3568v3 show that a reduced "baudclk" (e.g.
80MHz, compared to the standard 300MHz) significantly increases the
possibility of incorrect FIFO counters, i.e. erratum 5.
Print an info message if the clock is below the known good value of
300MHz.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-10-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The errata sheets doesn't say anything about CAN-FD, but tests on the
rk3568v2 and rk3568v3 show that receiving certain CAN-FD frames
triggers an Error Interrupt.
Mark the CAN-FD support as broken.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-6-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add driver for the Rockchip CAN-FD controller.
The IP core on the rk3568v2 SoC has 12 documented errata. Corrections
for these errata will be added in the upcoming patches.
Since several workarounds are required for the TX path, only add the
base driver that only implements the RX path.
Although the RX path implements CAN-FD support, it's not activated in
ctrlmode_supported, as the IP core in the rk3568v2 has problems with
receiving or sending certain CAN-FD frames.
Tested-by: Alibek Omarov <a1ba.omarov@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240904-rockchip-canfd-v5-4-8ae22bcb27cc@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Weizhao Ouyang
Robin van der Gracht
Marc Kleine-Budde