When more than one pdev is supported in the chip/SoC, the packet
belonging to second pdev is given to first pdev due to not identifying
the MAC id in the WBM error path. So ping fails.
In WBM error path, src link id information not available in the
descriptor. So get this information from the msdu_end 64bit tag. It
is necessary to get the src link id to identify the MAC id in the
given chip. Then only we can pass the skb to the corresponding pdev.
The msdu_end 64bit tag is available only if compact Rx TLVs
descriptors are used. Thus, src link id is fetched correctly in WBM
error path when compact descriptors are in use.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-11-quic_rajkbhag@quicinc.com
Most of the RX descriptors fields are currently not used in the
ath12k driver. Hence add support to selectively subscribe to the
required quad words (64 bits) within msdu_end and mpdu_start of
rx_desc.
Add compact rx_desc structures and configure the bit mask for Rx TLVs
(msdu_end, mpdu_start, mpdu_end) via registers. With these registers
SW can configure to DMA the partial TLV struct to Rx buffer.
Each TLV type has its own register to configure the mask value.
The mask value configured in register will indicate if a particular
QWORD has to be written to rx buffer or not i.e., if Nth bit is enabled
in the mask Nth QWORD will be written and it will not be written if the
bit is disabled in mask. While 0th bit indicates whether TLV tag will be
written or not.
Advantages of Qword subscription of TLVs
- Avoid multiple cache-line misses as the all the required fields
of the TLV are within 128 bytes.
- Memory optimization as TLVs + DATA + SHINFO can fit in 2k buffer
even for 64 bit kernel.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-10-quic_rajkbhag@quicinc.com
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
The hardware param hal_desc_sz value cannot be constant for the same
hardware. It depends on the size of rx_desc structure which may
change based on firmware capability to support word mask subscription.
Hence, remove hal_desc_sz from hardware param and add hal_rx_ops
to get the size of rx_desc in run time.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-9-quic_rajkbhag@quicinc.com
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
Most of the hal_ops are directly related to rx_desc.
Hence, split hal_ops into operations that are independent of rx_desc
(hal_ops) and the operations that are directly dependent on rx_desc
(hal_rx_ops). These hal_rx_ops depend on both hardware and firmware
hence move them out of hw_params.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-8-quic_rajkbhag@quicinc.com
In QCN9274, RX packet's multicast and broadcast(MCBC) flag is fetched
from RX descriptor's msdu_end info5 member but it is not correct
for QCN9274. Due to this with encryption, ARP request packet is wrongly
marked as MCBC packet and it is sent to mac80211 without setting
RX_FLAG_PN_VALIDATED & RX_FLAG_DECRYPTED flag. This results in packet
getting dropped in mac80211. Hence ping initiated from station to AP
fails.
Fix this by fetching correct MCBC flag in case of QCN9274.
For QC9274 MCBC flag should be fetched from RX descriptor's mpdu_start
info6 member.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 8f04852e90 ("wifi: ath12k: Use msdu_end to check MCBC")
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-5-quic_rajkbhag@quicinc.com
We observe some packets are discarded in ieee80211_rx_handlers_result
function for WCN7850. This is because the way to get multicast/broadcast
indicator with RX_MSDU_END_INFO5_DA_IS_MCBC & info5 is incorrect. It should
use RX_MSDU_END_INFO13_MCAST_BCAST & info13 to get multicast/broadcast
indicator.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231206141759.5430-1-quic_lingbok@quicinc.com
WCN7850 and QCN9274 currently use the same structure rx_msdu_end_qcn9274
for msdu_end. But content of msdu_end on WCN7850 is different from that of
QCN9274. Need to update it for WCN7850, otherwise will get the wrong
values when using it.
For example, TID is no longer in WCN7850's msdu_end. But
ath12k_dp_rx_process_err() and ath12k_dp_rx_process_wbm_err() still get
TID from msdu_end. So an uncertain value will be used in these two
functions on WCN7850.
Therefore, add new structure rx_msdu_end_wcn7850 for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230911093054.74943-1-quic_kangyang@quicinc.com
We are seeing a very low TCP throughput testing with some specific
tools. This is because for sub-frames of an AMSDU, MCBC flag in
mpdu_start may be not valid, and as a result those frames would be
dropped by kernel.
Add a new helper to get it from msdu_end. Also clean up original
helper since it is not needed any more.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230529081609.34567-1-quic_bqiang@quicinc.com
After previous patch checkpatch was giving warnings:
drivers/net/wireless/ath/ath12k/hal.h:158: Macro argument reuse 'ab' - possible side-effects?
drivers/net/wireless/ath/ath12k/hal.h:160: Macro argument reuse 'ab' - possible side-effects?
drivers/net/wireless/ath/ath12k/hal.h:162: Macro argument reuse 'ab' - possible side-effects?
drivers/net/wireless/ath/ath12k/hal.h:164: Macro argument reuse 'ab' - possible side-effects?
drivers/net/wireless/ath/ath12k/hal.h:173: Macro argument reuse 'ab' - possible side-effects?
drivers/net/wireless/ath/ath12k/hal.h:175: Macro argument reuse 'ab' - possible side-effects?
drivers/net/wireless/ath/ath12k/hal.h:177: Macro argument reuse 'ab' - possible side-effects?
drivers/net/wireless/ath/ath12k/hal.h:179: Macro argument reuse 'ab' - possible side-effects?
To fix those convert the macros into functions. As it was difficult to use
struct ath12k_base within hal.h, core.h was already including hal.h so
including back core.h would not work, move the functions also to hal.c.
No functional changes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220120655.19389-3-kvalo@kernel.org
It's considered evil if a macro is using a variable but not having the variable
as a parameter. So add the ab parameter to macros using that.
No functional changes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220120655.19389-2-kvalo@kernel.org
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Karthikeyan Periyasamy
Karthikeyan Kathirvel
Raj Kumar Bhagat
Lingbo Kong
Jeff Johnson
Kang Yang
Baochen Qiang
Colin Ian King
Kalle Valo