The VEB (virtual embedded switch) as a switch element can be
connected according datasheet though its uplink to:
- Physical port
- Port Virtualizer (not used directly by i40e driver but can
be present in MFP mode where the physical port is shared
between PFs)
- No uplink (aka floating VEB)
But VEB uplink cannot be connected to another VEB and any attempt
to do so results in:
"i40e 0000:02:00.0: couldn't add VEB, err -EIO aq_err I40E_AQ_RC_ENOENT"
that indicates "the uplink SEID does not point to valid element".
Remove this logic from the driver code this way:
1) For debugfs only allow to build floating VEB (uplink_seid == 0)
or main VEB (uplink_seid == mac_seid)
2) Do not recurse in i40e_veb_link_event() as no VEB cannot have
sub-VEBs
3) Ditto for i40e_veb_rebuild() + simplify the function as we know
that the VEB for rebuild can be only the main LAN VEB or some
of the floating VEBs
4) In i40e_rebuild() there is no need to check veb->uplink_seid
as the possible ones are 0 and MAC SEID
5) In i40e_vsi_release() do not take into account VEBs whose
uplink is another VEB as this is not possible
6) Remove veb_idx field from i40e_veb as a VEB cannot have
sub-VEBs
Tested using i40e debugfs interface:
1) Initial state
[root@cnb-03 net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 98.440641] i40e 0000:02:00.0: header: 3 reported 3 total
[ 98.446053] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 98.452593] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 98.458856] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
2) Add floating VEB
[root@cnb-03 net-next]# echo add relay > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 122.745630] i40e 0000:02:00.0: added relay 162
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 136.650049] i40e 0000:02:00.0: header: 4 reported 4 total
[ 136.655466] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 136.661994] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 136.668264] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 136.674787] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
3) Add VMDQ2 VSI to this new VEB
[root@cnb-03 net-next]# dmesg -c
[ 168.351763] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 168.374652] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 195.683204] i40e 0000:02:00.0: header: 5 reported 5 total
[ 195.688611] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 195.695143] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 195.701410] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 195.707935] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 195.714201] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
4) Try to delete the VEB
[root@cnb-03 net-next]# echo del relay 162 > $CMD
[root@cnb-03 net-next]# dmesg -c
[ 239.260901] i40e 0000:02:00.0: deleting relay 162
[ 239.265621] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left
5) Do PF reset and check switch status after rebuild
[root@cnb-03 net-next]# echo pfr > $CMD
[root@cnb-03 net-next]# echo dump switch > $CMD
[root@cnb-03 net-next]# dmesg -c
...
[ 272.333655] i40e 0000:02:00.0: header: 5 reported 5 total
[ 272.339066] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 272.345599] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 272.351862] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 272.358387] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 272.364654] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
6) Delete VSI and delete VEB
[ 297.199116] i40e 0000:02:00.0: deleting VSI 394
[ 299.807580] i40e 0000:02:00.0: deleting relay 162
[ 309.767905] i40e 0000:02:00.0: header: 3 reported 3 total
[ 309.773318] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 309.779845] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 309.786111] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Although the i40e supports so-called floating VEB (VEB without
an uplink connection to external network), this support is
broken. This functionality is currently unused (except debugfs)
but it will be used by subsequent series for switchdev mode
slow-path. Fix this by following:
1) Handle correctly floating VEB (VEB with uplink_seid == 0)
in i40e_reconstitute_veb() and look for owner VSI and
create it only for non-floating VEBs and also set bridge
mode only for such VEBs as the floating ones are using
always VEB mode.
2) Handle correctly floating VEB in i40e_veb_release() and
disallow its release when there are some VSIs. This is
different from regular VEB that have owner VSI that is
connected to VEB's uplink after VEB deletion by FW.
3) Fix i40e_add_veb() to handle 'vsi' that is NULL for floating
VEBs. For floating VEB use 0 for downlink SEID and 'true'
for 'default_port' parameters as per datasheet.
4) Fix 'add relay' command in i40e_dbg_command_write() to allow
to create floating VEB by 'add relay 0 0' or 'add relay'
Tested using debugfs:
1) Initial state
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 173.701286] i40e 0000:02:00.0: header: 3 reported 3 total
[ 173.706701] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 173.713241] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 173.719507] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
2) Add floating VEB
[root@host net-next]# CMD="/sys/kernel/debug/i40e/0000:02:00.0/command"
[root@host net-next]# echo add relay > $CMD
[root@host net-next]# dmesg -c
[ 245.551720] i40e 0000:02:00.0: added relay 162
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 276.984371] i40e 0000:02:00.0: header: 4 reported 4 total
[ 276.989779] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 276.996302] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 277.002569] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
[ 277.009091] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
3) Add VMDQ2 VSI to this new VEB
[root@host net-next]# echo add vsi 162 > $CMD
[root@host net-next]# dmesg -c
[ 332.314030] i40e 0000:02:00.0: added VSI 394 to relay 162
[ 332.337486] enp2s0f0np0v0: NIC Link is Up, 40 Gbps Full Duplex, Flow Control: None
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 387.284490] i40e 0000:02:00.0: header: 5 reported 5 total
[ 387.289904] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 387.296446] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 387.302708] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 387.309234] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 387.315500] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
4) Try to delete the VEB
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# dmesg -c
[ 428.749297] i40e 0000:02:00.0: deleting relay 162
[ 428.754011] i40e 0000:02:00.0: can't remove VEB 162 with 1 VSIs left
5) Do PF reset and check switch status after rebuild
[root@host net-next]# echo pfr > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 738.056172] i40e 0000:02:00.0: header: 5 reported 5 total
[ 738.061577] i40e 0000:02:00.0: type=19 seid=394 uplink=162 downlink=16
[ 738.068104] i40e 0000:02:00.0: type=17 seid=162 uplink=0 downlink=0
[ 738.074367] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 738.080892] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 738.087160] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
6) Delete VSI and delete VEB
[root@host net-next]# echo del vsi 394 > $CMD
[root@host net-next]# echo del relay 162 > $CMD
[root@host net-next]# echo dump switch > $CMD
[root@host net-next]# dmesg -c
[ 1233.081126] i40e 0000:02:00.0: deleting VSI 394
[ 1239.345139] i40e 0000:02:00.0: deleting relay 162
[ 1244.886920] i40e 0000:02:00.0: header: 3 reported 3 total
[ 1244.892328] i40e 0000:02:00.0: type=19 seid=392 uplink=160 downlink=16
[ 1244.898853] i40e 0000:02:00.0: type=17 seid=160 uplink=2 downlink=0
[ 1244.905119] i40e 0000:02:00.0: type=19 seid=390 uplink=160 downlink=16
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add two helpers i40e_(veb|vsi)_get_by_seid() to find corresponding
VEB or VSI by their SEID value and use these helpers to replace
existing open-coded loops.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce i40e_for_each_vsi() and i40e_for_each_veb() helper
macros and use them to iterate relevant arrays.
Replace pattern:
for (i = 0; i < pf->num_alloc_vsi; i++)
by:
i40e_for_each_vsi(pf, i, vsi)
and pattern:
for (i = 0; i < I40E_MAX_VEB; i++)
by
i40e_for_each_veb(pf, i, veb)
These macros also check if array item pf->vsi[i] or pf->veb[i]
are not NULL and skip such items so we can remove redundant
checks from loop bodies.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use existing i40e_find_vsi_by_type() to find a VSI
associated with flow director.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-06 (igb, igc)
This series contains updates to igb and igc drivers.
Kunwu Chan adjusts firmware version string implementation to resolve
possible NULL pointer issue for igb.
Sasha removes workaround on igc.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Remove temporary workaround
igb: Fix string truncation warnings in igb_set_fw_version
====================
Link: https://lore.kernel.org/r/20240214180347.3219650-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for LEDs on i225/i226. The LEDs can be controlled via sysfs
from user space using the netdev trigger. The LEDs are named as
igc-<bus><device>-<led> to be easily identified.
Offloading link speed and activity are supported. Other modes are simulated
in software by using on/off. Tested on Intel i225.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240213184138.1483968-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To fully support initializing the LAG support code, a DDP package that
extracts the logical port from the metadata is required. If such a
package is not present, there could be difficulties in supporting some
bond types.
Add a check into the initialization flow that will bypass the new paths
if any of the support pieces are missing.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Fixes: df006dd4b1 ("ice: Add initial support framework for LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240213183957.1483857-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PHY_CONTROL register works as defined in the IEEE 802.3 specification
(IEEE 802.3-2008 22.2.4.1). Tidy up the temporary workaround.
User impact: PHY can now be powered down when the ethernet link is down.
Testing hints: ip link set down <device> (or just disconnect the
ethernet cable).
Oldest tested NVM version is: 1045:740.
Fixes: 5586838fe9 ("igc: Add code for PHY support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 1978d3ead8 ("intel: fix string truncation warnings")
fixes '-Wformat-truncation=' warnings in igb_main.c by using kasprintf.
drivers/net/ethernet/intel/igb/igb_main.c:3092:53: warning：‘%d’ directive output may be truncated writing between 1 and 5 bytes into a region of size between 1 and 13 [-Wformat-truncation=]
3092 | "%d.%d, 0x%08x, %d.%d.%d",
| ^~
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535]
3092 | "%d.%d, 0x%08x, %d.%d.%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/igb/igb_main.c:3092:34: note：directive argument in the range [0, 65535]
drivers/net/ethernet/intel/igb/igb_main.c:3090:25: note：‘snprintf’ output between 23 and 43 bytes into a destination of size 32
kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fix this warning by using a larger space for adapter->fw_version,
and then fall back and continue to use snprintf.
Fixes: 1978d3ead8 ("intel: fix string truncation warnings")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Cc: Kunwu Chan <kunwu.chan@hotmail.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-12 (i40e)
This series contains updates to i40e driver only.
Ivan Vecera corrects the looping value used while waiting for queues to
be disabled as well as an incorrect mask being used for DCB
configuration.
Maciej resolves an issue related to XDP traffic; removing a double call to
i40e_pf_rxq_wait() and accounting for XDP rings when stopping rings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Seth reported that on his side XDP traffic can not survive a round of
down/up against i40e interface. Dmesg output was telling us that we were
not able to disable the very first XDP ring. That was due to the fact
that in i40e_vsi_stop_rings() in a pre-work that is done before calling
i40e_vsi_wait_queues_disabled(), XDP Tx queues were not taken into the
account.
To fix this, let us distinguish between Rx and Tx queue boundaries and
take into the account XDP queues for Tx side.
Reported-by: Seth Forshee <sforshee@kernel.org>
Closes: https://lore.kernel.org/netdev/ZbkE7Ep1N1Ou17sA@do-x1extreme/
Fixes: 65662a8dcd ("i40e: Fix logic of disabling queues")
Tested-by: Seth Forshee <sforshee@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, when interface is being brought down and
i40e_vsi_stop_rings() is called, i40e_pf_rxq_wait() is called two times,
which is wrong. To showcase this scenario, simplified call stack looks
as follows:
i40e_vsi_stop_rings()
i40e_control wait rx_q()
i40e_control_rx_q()
i40e_pf_rxq_wait()
i40e_vsi_wait_queues_disabled()
i40e_pf_rxq_wait() // redundant call
To fix this, let us s/i40e_control_wait_rx_q/i40e_control_rx_q within
i40e_vsi_stop_rings().
Fixes: 65662a8dcd ("i40e: Fix logic of disabling queues")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mask used for clearing PRTDCB_RETSTCC register in function
i40e_dcb_hw_rx_ets_bw_config() is incorrect as there is used
define I40E_PRTDCB_RETSTCC_ETSTC_SHIFT instead of define
I40E_PRTDCB_RETSTCC_ETSTC_MASK.
The PRTDCB_RETSTCC register is used to configure whether ETS
or strict priority is used as TSA in Rx for particular TC.
In practice it means that once the register is set to use ETS
as TSA then it is not possible to switch back to strict priority
without CoreR reset.
Fix the value in the clearing mask.
Fixes: 90bc8e003b ("i40e: Add hardware configuration for software based DCB")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39f ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently when PF administratively sets VF's MAC address and the VF
is put down (VF tries to delete all MACs) then the MAC is removed
from MAC filters and primary VF MAC is zeroed.
Do not allow untrusted VF to remove primary MAC when it was set
administratively by PF.
Reproducer:
1) Create VF
2) Set VF interface up
3) Administratively set the VF's MAC
4) Put VF interface down
[root@host ~]# echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
[root@host ~]# ip link set enp2s0f0v0 up
[root@host ~]# ip link set enp2s0f0 vf 0 mac fe:6c:b5:da:c7:7d
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether fe:6c:b5:da:c7:7d brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
[root@host ~]# ip link set enp2s0f0v0 down
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
Fixes: 700bbf6c1f ("i40e: allow VF to remove any MAC filter")
Fixes: ceb29474bb ("i40e: Add support for VF to specify its primary MAC address")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240208180335.1844996-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During devlink reload it is needed to remove debugfs entries
correlated with only one PF. ice_debugfs_exit() removes all
entries created by ice driver so we can't use it.
Introduce ice_debugfs_pf_deinit() in order to release PF's
debugfs entries. Move ice_debugfs_exit() call to ice_module_exit(),
it makes more sense since ice_debugfs_init() is called in
ice_module_init() and not in ice_probe().
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Recent changes to the devlink reload (commit 9b2348e2d6
("devlink: warn about existing entities during reload-reinit"))
force the drivers to destroy devlink ports during reinit.
Adjust ice driver to this requirement, unregister netdvice, destroy
devlink port. ice_init_eth() was removed and all the common code
between probe and reload was moved to ice_load().
During devlink reload we can't take devl_lock (it's already taken)
and in ice_probe() we have to lock it. Use devl_* variant of the API
which does not acquire and release devl_lock. Guard ice_load()
with devl_lock only in case of probe.
Suggested-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
E825C devices shall support the new signing type of RSA 3K for new DDP
section (SEGMENT_SIGN_TYPE_RSA3K_E825 (5) - already in the code).
The driver is responsible to verify the presence of correct signing type.
Add 3k signinig support for E825C devices based on mac_type:
ICE_MAC_GENERIC_3K_E825;
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
E800 series devices have a couple of quirks:
1. Sideband control queues are not supported
2. The registers that the driver needs to program for the "Precision
Time Protocol (PTP)" feature are different for E800 series devices
compared to other devices supported by this driver.
Both these require conditional logic based on the underlying device we
are dealing with.
The function ice_is_sbq_supported added by commit 8f5ee3c477
("ice: add support for sideband messages") addresses (1).
The same function can be used to address (2) as well
but this just looks weird readability wise in cases that have nothing
to do with sideband control queues:
if (ice_is_sbq_supported(hw))
/* program register A */
else
/* program register B */
For these cases, the function ice_is_generic_mac introduced by this
patch communicates the idea/intention better. Also rework
ice_is_sbq_supported to use this new function.
As side-band queue is supported for E825C devices, it's mac_type is
considered as generic mac_type.
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce new Intel Ethernet E825C family devices.
Add new PCI device IDs which are going to be supported by the
driver:
- 579C: Intel(R) Ethernet Connection E825-C for backplane
- 579D: Intel(R) Ethernet Connection E825-C for QSFP
- 579E: Intel(R) Ethernet Connection E825-C for SFP
- 579F: Intel(R) Ethernet Connection E825-C for SGMII
Add helper function ice_is_e825c() to verify if the running device
belongs to E825C family.
Co-developed-by: Jan Glaza <jan.glaza@intel.com>
Signed-off-by: Jan Glaza <jan.glaza@intel.com>
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
igc: ethtool: Flex filter cleanup
Kurt Kanzenbach says:
This series contains some cosmetics for the flex filter code. The fixes have
been merged separately via -net already.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Unify filtering rule fields
igc: Use netdev printing functions for flex filters
igc: Use reverse xmas tree
====================
Link: https://lore.kernel.org/r/20240207191656.1250777-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-02-06 (ixgbe)
This series contains updates to ixgbe driver only.
Jedrzej continues cleanup work from conversion away from ixgbe_status;
s32 values are changed to int, various style issues are addressed, and
some return statements refactored to address some smatch warnings.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixgbe: Clarify the values of the returning status
ixgbe: Rearrange args to fix reverse Christmas tree
ixgbe: Convert ret val type from s32 to int
====================
Link: https://lore.kernel.org/r/20240206214054.1002919-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/stmicro/stmmac/common.h
38cc3c6dcc ("net: stmmac: protect updates of 64-bit statistics counters")
fd5a6a7131 ("net: stmmac: est: Per Tx-queue error count for HLBF")
c5c3e1bfc9 ("net: stmmac: Offload queueMaxSDU from tc-taprio")
drivers/net/wireless/microchip/wilc1000/netdev.c
c901388028 ("wifi: fill in MODULE_DESCRIPTION()s for wilc1000")
328efda22a ("wifi: wilc1000: do not realloc workqueue everytime an interface is added")
net/unix/garbage.c
11498715f2 ("af_unix: Remove io_uring code for GC.")
1279f9d9de ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All filtering parameters such as EtherType and VLAN TCI are stored in host
byte order except for the VLAN EtherType. Unify it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
All igc filter implementations use netdev_*() printing functions except for
the flex filters. Unify it.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use reverse xmas tree coding style convention in igc_add_flex_filter().
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The kernel build regressions/improvements email contained a couple of
issues with old compilers (in fact all the reports were on different
architectures, but all gcc 5.5) and the FIELD_PREP() and FIELD_GET()
conversions. They're all because an integer #define that should have
been declared as unsigned, was shifted to the point that it could set
the sign bit.
The fix just involves making sure the defines use the "U" identifier on
the constants to make sure they're unsigned. Should make the checkers
happier.
Confirmed with objdump before/after that there is no change to the
binaries.
Issues were reported as follows:
./drivers/net/ethernet/intel/ice/ice_base.c:238:7: note: in expansion of macro 'FIELD_GET'
(FIELD_GET(GLINT_CTL_ITR_GRAN_25_M, regval) == ICE_ITR_GRAN_US))
^
./include/linux/compiler_types.h:435:38: error: call to '__compiletime_assert_1093' declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_nvm.c:709:16: note: in expansion of macro ‘FIELD_GET’
orom->major = FIELD_GET(ICE_OROM_VER_MASK, combo_ver);
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_796’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/ice/ice_common.c:945:18: note: in expansion of macro ‘FIELD_GET’
u8 max_agg_bw = FIELD_GET(GL_PWR_MODE_CTL_CAR_MAX_BW_M,
^
./include/linux/compiler_types.h:435:38: error: call to ‘__compiletime_assert_420’ declared with attribute error: FIELD_GET: mask is not constant
drivers/net/ethernet/intel/i40e/i40e_dcb.c:458:8: note: in expansion of macro ‘FIELD_GET’
oui = FIELD_GET(I40E_LLDP_TLV_OUI_MASK, ouisubtype);
^
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Closes: https://lore.kernel.org/lkml/d03e90ca-8485-4d1b-5ec1-c3398e0e8da@linux-m68k.org/ #i40e #ice
Fixes: 62589808d7 ("i40e: field get conversion")
Fixes: 5a259f8e0b ("ice: field get conversion")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20240206022906.2194214-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Converting s32 functions to regular int in the previous patch of the series
caused triggering smatch warnings about missing error code.
New smatch warnings:
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c:2884 ixgbe_get_lcd_t_x550em() warn: missing error code? 'status'
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c:3130 ixgbe_enter_lplu_t_x550em() warn: missing error code? 'status'
Old smatch warnings:
drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c:2890 ixgbe_get_lcd_t_x550em() warn: missing error code? 'status'
Fix it by clearly stating returning error code as 0.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202401041701.6QKTsZmx-lkp@intel.com/
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Clean up the code touched during type conversion by the previous patch
of the series.
Suggested-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently big amount of the functions returning standard error codes
are of type s32. Convert them to regular ints as typdefs here are not
necessary to return standard error codes.
Fix incorrect args alignment in touched functions.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Copy paste issue left a comment for this structure that has nothing
to do with FW alignment; remove the comment.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
HW incorrectly reports EIPE errors on encapsulated packets
with L2 padding inside inner packet. HW shows outer UDP/IPV4
packet checksum errors as part of the EIPE flags of the
Rx descriptor. These are reported only if checksum offload
is enabled and L3/L4 parsed flag is valid in Rx descriptor.
When that error is reported by HW, we don't act on it
instead of incrementing main Rx errors statistic as it
would normally happen.
Add a new statistic to count these errors since we still want
to print them.
Signed-off-by: Aniruddha Paul <aniruddha.paul@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jan Glaza <jan.glaza@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, XSK control path in ice driver calls directly
ice_vsi_cfg_txq() whereas we have ice_vsi_cfg_single_txq() for that
purpose. Use the latter from XSK side and make ice_vsi_cfg_txq() static.
ice_vsi_cfg_txq() resides in ice_base.c and is rather big, so to reduce
the code churn let us move the callers of it from ice_lib.c to
ice_base.c.
This change puts ice_qp_ena() on nice diet due to the checks and
operations that ice_vsi_cfg_single_{r,t}xq() do internally.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-182 (-182)
Function old new delta
ice_xsk_pool_setup 2165 1983 -182
Total: Before=472597, After=472415, chg -0.04%
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, XSK control path in ice driver calls directly
ice_vsi_cfg_rxq() whereas we have ice_vsi_cfg_single_rxq() for that
purpose. Use the latter from XSK side and make ice_vsi_cfg_rxq() static.
ice_vsi_cfg_rxq() resides in ice_base.c and is rather big, so to reduce
the code churn let us move two callers of it from ice_lib.c to
ice_base.c.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the arm random config file, kconfig option 'CONFIG_AEABI' is
disabled which results in adding the compiler flag '-mabi=apcs-gnu'.
This causes the compiler to add padding in virtchnl2_ptype
structure to align it to 8 bytes, resulting in the following
size check failure:
include/linux/build_bug.h:78:41: error: static assertion failed: "(6) == sizeof(struct virtchnl2_ptype)"
78 | #define __static_assert(expr, msg, ...) _Static_assert(expr, msg)
| ^~~~~~~~~~~~~~
include/linux/build_bug.h:77:34: note: in expansion of macro '__static_assert'
77 | #define static_assert(expr, ...) __static_assert(expr, ##__VA_ARGS__, #expr)
| ^~~~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:26:9: note: in expansion of macro 'static_assert'
26 | static_assert((n) == sizeof(struct X))
| ^~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:982:1: note: in expansion of macro 'VIRTCHNL2_CHECK_STRUCT_LEN'
982 | VIRTCHNL2_CHECK_STRUCT_LEN(6, virtchnl2_ptype);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid the compiler padding by using "__packed" structure
attribute for the virtchnl2_ptype struct. Also align the
structure by using "__aligned(2)" for better code optimization.
Fixes: 0d7502a9b4 ("virtchnl: add virtchnl version 2 ops")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312220250.ufEm8doQ-lkp@intel.com
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240131222241.2087516-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pass additional argunent status_error over lock_status_get()
so drivers can fill it up. In case they do, expose the value over
previously introduced attribute to user. Do it only in case the
current lock_status is either "unlocked" or "holdover".
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This is in preparation of using the existing names for linkmode
bitmaps.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ice driver currently attempts to destroy and re-initialize the Tx
timestamp tracker during the reset flow. The release of the Tx tracker
only happened during CORE reset or GLOBAL reset. The ice_ptp_rebuild()
function always calls the ice_ptp_init_tx function which will allocate
a new tracker data structure, resulting in memory leaks during PF reset.
Certainly the driver should not be allocating a new tracker without
removing the old tracker data, as this results in a memory leak.
Additionally, there's no reason to remove the tracker memory during a
reset. Remove this logic from the reset and rebuild flow. Instead of
releasing the Tx tracker, flush outstanding timestamps just before we
reset the PHY timestamp block in ice_ptp_cfg_phy_interrupt().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_reset() function uses a goto to skip past clock owner
operations if performing a PF reset or if the device is not the clock
owner. This is a bit confusing. Factor this out into
ice_ptp_rebuild_owner() instead.
The ice_ptp_reset() function is called by ice_rebuild() to restore PTP
functionality after a device reset. Follow the convention set by the
ice_main.c file and rename this function to ice_ptp_rebuild(), in the
same way that we have ice_prepare_for_reset() and
ice_ptp_prepare_for_reset().
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_tx_cfg_intr() function sends a control queue message to
configure the PHY timestamp interrupt block. This is a very similar name
to a function which is used to configure the MAC Other Interrupt Cause
Enable register.
Rename this function to ice_ptp_cfg_phy_interrupt in order to make it
more obvious to the reader what action it performs, and distinguish it
from other similarly named functions.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
E810 hardware does not have a Tx timestamp ready bitmap. Don't check
has_ready_bitmap in E810-specific functions.
Add has_ready_bitmap check in ice_ptp_process_tx_tstamp() to stop
relying on the fact that ice_get_phy_tx_tstamp_ready() returns all 1s.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The tx->verify_cached flag is used to inform the Tx timestamp tracking
code whether it needs to verify the cached Tx timestamp value against
a previous captured value. This is necessary on E810 hardware which does
not have a Tx timestamp ready bitmap.
In addition, we currently rely on the fact that the
ice_get_phy_tx_tstamp_ready() function returns all 1s for E810 hardware.
Instead of introducing a brand new flag, rename and verify_cached to
has_ready_bitmap, inverting the relevant checks.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ice_ptp_prepare_for_reset() and ice_ptp_reset() functions currently
check the pf->flags ICE_FLAG_PFR_REQ bit to determine if the current
reset is a PF reset or not.
This is problematic, because it is possible that a PF reset and a higher
level reset (CORE reset, GLOBAL reset, EMP reset) are requested
simultaneously. In that case, the driver performs the highest level
reset requested. However, the ICE_FLAG_PFR_REQ flag will still be set.
The main driver reset functions take an enum ice_reset_req indicating
which reset is actually being performed. Pass this data into the PTP
functions and rely on this instead of relying on the driver flags.
This ensures that the PTP code performs the proper level of reset that
the driver is actually undergoing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add PTP state machine so that the driver can correctly identify PTP
state around resets.
When the driver got information about ungraceful reset, PTP was not
prepared for reset and it returned error. When this situation occurs,
prepare PTP before rebuilding its structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
All error handling paths, except this one, go to 'out' where
release_swfw_sync() is called.
This call balances the acquire_swfw_sync() call done at the beginning of
the function.
Branch to the error handling path in order to correctly release some
resources in case of error.
Fixes: ae14a1d8e1 ("ixgbe: Fix IOSF SB access issues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The e1000e driver supports hardware with a variety of different clock
speeds, and thus a variety of different increment values used for
programming its PTP hardware clock.
The values currently programmed in e1000e_ptp_init are incorrect. In
particular, only two maximum adjustments are used: 24000000 - 1, and
600000000 - 1. These were originally intended to be used with the 96 MHz
clock and the 25 MHz clock.
Both of these values are actually slightly too high. For the 96 MHz clock,
the actual maximum value that can safely be programmed is 23,999,938. For
the 25 MHz clock, the maximum value is 599,999,904.
Worse, several devices use a 24 MHz clock or a 38.4 MHz clock. These parts
are incorrectly assigned one of either the 24million or 600million values.
For the 24 MHz clock, this is not a significant issue: its current
increment value can support an adjustment up to 7billion in the positive
direction. However, the 38.4 KHz clock uses an increment value which can
only support up to 230,769,157 before it starts overflowing.
To understand where these values come from, consider that frequency
adjustments have the form of:
new_incval = base_incval + (base_incval * adjustment) / (unit of adjustment)
The maximum adjustment is reported in terms of parts per billion:
new_incval = base_incval + (base_incval * adjustment) / 1 billion
The largest possible adjustment is thus given by the following:
max_incval = base_incval + (base_incval * max_adj) / 1 billion
Re-arranging to solve for max_adj:
max_adj = (max_incval - base_incval) * 1 billion / base_incval
We also need to ensure that negative adjustments cannot underflow. This can
be achieved simply by ensuring max_adj is always less than 1 billion.
Introduce new macros in e1000.h codifying the maximum adjustment in PPB for
each frequency given its associated increment values. Also clarify where
these values come from by commenting about the above equations.
Replace the switch statement in e1000e_ptp_init with one which mirrors the
increment value switch statement from e1000e_get_base_timinica. For each
device, assign the appropriate maximum adjustment based on its frequency.
Some parts can have one of two frequency modes as determined by
E1000_TSYNCRXCTL_SYSCFI.
Since the new flow directly matches the assignments in
e1000e_get_base_timinca, and uses well defined macro names, it is much
easier to verify that the resulting maximum adjustments are correct. It
also avoids difficult to parse construction such as the "hw->mac.type <
e1000_phc_lpt", and the use of fallthrough which was especially confusing
when combined with a conditional block.
Note that I believe the current increment value configuration used for
24MHz clocks is sub-par, as it leaves at least 3 extra bits available in
the INCVALUE register. However, fixing that requires more careful review of
the clock rate and associated values.
Reported-by: Trey Harrison <harrisondigitalmedia@gmail.com>
Fixes: 68fe1d5da5 ("e1000e: Add Support for 38.4MHZ frequency")
Fixes: d89777bf0e ("e1000e: add support for IEEE-1588 PTP")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Now that i40e driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. i40e_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Fixes: 1c9ba9c146 ("i40e: xsk: add RX multi-buffer support")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-12-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
i40e support XDP multi-buffer so it is supposed to use
__xdp_rxq_info_reg() instead of xdp_rxq_info_reg() and set the
frag_size. It can not be simply converted at existing callsite because
rx_buf_len could be un-initialized, so let us register xdp_rxq_info
within i40e_configure_rx_ring(), which happen to be called with already
initialized rx_buf_len value.
Commit 5180ff1364 ("i40e: use int for i40e_status") converted 'err' to
int, so two variables to deal with return codes are not needed within
i40e_configure_rx_ring(). Remove 'ret' and use 'err' to handle status
from xdp_rxq_info registration.
Fixes: e213ced19b ("i40e: add support for XDP multi-buffer Rx")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-11-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Now that ice driver correctly sets up frag_size in xdp_rxq_info, let us
make it work for ZC multi-buffer as well. ice_rx_ring::rx_buf_len for ZC
is being set via xsk_pool_get_rx_frame_size() and this needs to be
propagated up to xdp_rxq_info.
Use a bigger hammer and instead of unregistering only xdp_rxq_info's
memory model, unregister it altogether and register it again and have
xdp_rxq_info with correct frag_size value.
Fixes: 1bbc04de60 ("ice: xsk: add RX multi-buffer support")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-9-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Ice and i40e ZC drivers currently set offset of a frag within
skb_shared_info to 0, which is incorrect. xdp_buffs that come from
xsk_buff_pool always have 256 bytes of a headroom, so they need to be
taken into account to retrieve xdp_buff::data via skb_frag_address().
Otherwise, bpf_xdp_frags_increase_tail() would be starting its job from
xdp_buff::data_hard_start which would result in overwriting existing
payload.
Fixes: 1c9ba9c146 ("i40e: xsk: add RX multi-buffer support")
Fixes: 1bbc04de60 ("ice: xsk: add RX multi-buffer support")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-8-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
xdp_rxq_info struct can be registered by drivers via two functions -
xdp_rxq_info_reg() and __xdp_rxq_info_reg(). The latter one allows
drivers that support XDP multi-buffer to set up xdp_rxq_info::frag_size
which in turn will make it possible to grow the packet via
bpf_xdp_adjust_tail() BPF helper.
Currently, ice registers xdp_rxq_info in two spots:
1) ice_setup_rx_ring() // via xdp_rxq_info_reg(), BUG
2) ice_vsi_cfg_rxq() // via __xdp_rxq_info_reg(), OK
Cited commit under fixes tag took care of setting up frag_size and
updated registration scheme in 2) but it did not help as
1) is called before 2) and as shown above it uses old registration
function. This means that 2) sees that xdp_rxq_info is already
registered and never calls __xdp_rxq_info_reg() which leaves us with
xdp_rxq_info::frag_size being set to 0.
To fix this misbehavior, simply remove xdp_rxq_info_reg() call from
ice_setup_rx_ring().
Fixes: 2fba7dc515 ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-7-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
XDP programs can shrink packets by calling the bpf_xdp_adjust_tail()
helper function. For multi-buffer packets this may lead to reduction of
frag count stored in skb_shared_info area of the xdp_buff struct. This
results in issues with the current handling of XDP_PASS and XDP_DROP
cases.
For XDP_PASS, currently skb is being built using frag count of
xdp_buffer before it was processed by XDP prog and thus will result in
an inconsistent skb when frag count gets reduced by XDP prog. To fix
this, get correct frag count while building the skb instead of using
pre-obtained frag count.
For XDP_DROP, current page recycling logic will not reuse the page but
instead will adjust the pagecnt_bias so that the page can be freed. This
again results in inconsistent behavior as the page refcnt has already
been changed by the helper while freeing the frag(s) as part of
shrinking the packet. To fix this, only adjust pagecnt_bias for buffers
that are stillpart of the packet post-xdp prog run.
Fixes: e213ced19b ("i40e: add support for XDP multi-buffer Rx")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-6-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Fix an OOM panic in XDP_DRV mode when a XDP program shrinks a
multi-buffer packet by 4k bytes and then redirects it to an AF_XDP
socket.
Since support for handling multi-buffer frames was added to XDP, usage
of bpf_xdp_adjust_tail() helper within XDP program can free the page
that given fragment occupies and in turn decrease the fragment count
within skb_shared_info that is embedded in xdp_buff struct. In current
ice driver codebase, it can become problematic when page recycling logic
decides not to reuse the page. In such case, __page_frag_cache_drain()
is used with ice_rx_buf::pagecnt_bias that was not adjusted after
refcount of page was changed by XDP prog which in turn does not drain
the refcount to 0 and page is never freed.
To address this, let us store the count of frags before the XDP program
was executed on Rx ring struct. This will be used to compare with
current frag count from skb_shared_info embedded in xdp_buff. A smaller
value in the latter indicates that XDP prog freed frag(s). Then, for
given delta decrement pagecnt_bias for XDP_DROP verdict.
While at it, let us also handle the EOP frag within
ice_set_rx_bufs_act() to make our life easier, so all of the adjustments
needed to be applied against freed frags are performed in the single
place.
Fixes: 2fba7dc515 ("ice: Add support for XDP multi-buffer on Rx side")
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-5-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
XDP multi-buffer support introduced XDP_FLAGS_HAS_FRAGS flag that is
used by drivers to notify data path whether xdp_buff contains fragments
or not. Data path looks up mentioned flag on first buffer that occupies
the linear part of xdp_buff, so drivers only modify it there. This is
sufficient for SKB and XDP_DRV modes as usually xdp_buff is allocated on
stack or it resides within struct representing driver's queue and
fragments are carried via skb_frag_t structs. IOW, we are dealing with
only one xdp_buff.
ZC mode though relies on list of xdp_buff structs that is carried via
xsk_buff_pool::xskb_list, so ZC data path has to make sure that
fragments do *not* have XDP_FLAGS_HAS_FRAGS set. Otherwise,
xsk_buff_free() could misbehave if it would be executed against xdp_buff
that carries a frag with XDP_FLAGS_HAS_FRAGS flag set. Such scenario can
take place when within supplied XDP program bpf_xdp_adjust_tail() is
used with negative offset that would in turn release the tail fragment
from multi-buffer frame.
Calling xsk_buff_free() on tail fragment with XDP_FLAGS_HAS_FRAGS would
result in releasing all the nodes from xskb_list that were produced by
driver before XDP program execution, which is not what is intended -
only tail fragment should be deleted from xskb_list and then it should
be put onto xsk_buff_pool::free_list. Such multi-buffer frame will never
make it up to user space, so from AF_XDP application POV there would be
no traffic running, however due to free_list getting constantly new
nodes, driver will be able to feed HW Rx queue with recycled buffers.
Bottom line is that instead of traffic being redirected to user space,
it would be continuously dropped.
To fix this, let us clear the mentioned flag on xsk_buff_pool side
during xdp_buff initialization, which is what should have been done
right from the start of XSK multi-buffer support.
Fixes: 1bbc04de60 ("ice: xsk: add RX multi-buffer support")
Fixes: 1c9ba9c146 ("i40e: xsk: add RX multi-buffer support")
Fixes: 24ea50127e ("xsk: support mbuf on ZC RX")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20240124191602.566724-3-maciej.fijalkowski@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
idpf registers multiple netdevs (virtual ports) for one PCI function,
but it does not provide a way for userspace to distinguish them with
sysfs attributes. Per Documentation/ABI/testing/sysfs-class-net, it is
a bug not to set dev_port for independent ports on the same PCI bus,
device and function.
Without dev_port set, systemd-udevd's default naming policy attempts
to assign the same name ("ens2f0") to all four idpf netdevs on my test
system and obviously fails, leaving three of them with the initial
eth<N> name.
With this patch, systemd-udevd is able to assign unique names to the
netdevs (e.g. "ens2f0", "ens2f0d1", "ens2f0d2", "ens2f0d3").
The Intel-provided out-of-tree idpf driver already sets dev_port. In
this patch I chose to do it in the same place in the idpf_cfg_netdev
function.
Fixes: 0fe45467a1 ("idpf: add create vport and netdev configuration")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 56df345917 ("i40e: Remove circular header dependencies and fix
headers") redistributed a number of includes from one large header file
to the locations they were needed. In some environments, types.h is not
included and causing compile issues. The driver should not rely on
implicit inclusion from other locations; explicitly include it to these
files.
Snippet of issue. Entire log can be seen through the Closes: link.
In file included from drivers/net/ethernet/intel/i40e/i40e_diag.h:7,
from drivers/net/ethernet/intel/i40e/i40e_diag.c:4:
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h:33:9: error: unknown type name '__le16'
33 | __le16 flags;
| ^~~~~~
drivers/net/ethernet/intel/i40e/i40e_adminq_cmd.h:34:9: error: unknown type name '__le16'
34 | __le16 opcode;
| ^~~~~~
...
drivers/net/ethernet/intel/i40e/i40e_diag.h:22:9: error: unknown type name 'u32'
22 | u32 elements; /* number of elements if array */
| ^~~
drivers/net/ethernet/intel/i40e/i40e_diag.h:23:9: error: unknown type name 'u32'
23 | u32 stride; /* bytes between each element */
Reported-by: Martin Zaharinov <micron10@gmail.com>
Closes: https://lore.kernel.org/netdev/21BBD62A-F874-4E42-B347-93087EEA8126@gmail.com/
Fixes: 56df345917 ("i40e: Remove circular header dependencies and fix headers")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240117172534.3555162-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-01-03 (i40e, ice, igc)
This series contains updates to i40e, ice, and igc drivers.
Ke Xiao fixes use after free for unicast filters on i40e.
Andrii restores VF MSI-X flag after PCI reset on i40e.
Paul corrects admin queue link status structure to fulfill firmware
expectations for ice.
Rodrigo Cataldo corrects value used for hicredit calculations on igc.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Fix hicredit calculation
ice: fix Get link status data length
i40e: Restore VF MSI-X state during PCI reset
i40e: fix use-after-free in i40e_aqc_add_filters()
====================
Link: https://lore.kernel.org/r/20240103193254.822968-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
t-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-01-02 (ice)
This series contains updates to ice driver only.
Karol adds support for capable devices to receive timestamp via
interrupt rather than polling to allow for less delay.
Andrii adds support switchdev hardware packet mirroring.
Jake reworks VF rebuild to avoid destroying objects that do not need to
be.
Jan S removes reporting of rx_len_errors as they are incorrectly reported
by hardware.
Jan G adds const modifier to some uses that are applicable.
Kunwu Chan adds some checks for failed memory allocations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-12-27 (igc)
This series contains updates to igc driver only.
Kurt Kanzenbach resolves issues around VLAN ntuple rules; correctly
reporting back added rules and checking for valid values.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Check VLAN EtherType mask
igc: Check VLAN TCI mask
igc: Report VLAN EtherType matching back to user
====================
Link: https://lore.kernel.org/r/20231227210041.3035055-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-12-27 (ice, i40e)
This series contains updates to ice and i40e drivers.
Katarzyna changes message to no longer be reported as error under
certain conditions as it can be expected on ice.
Ngai-Mint ensures VSI is always closed when stopping interface to
prevent NULL pointer dereference for ice.
Arkadiusz corrects reporting of phase offset value for ice.
Sudheer corrects checking on ADQ filters to prevent invalid values on
i40e.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix filter input checks to prevent config with invalid values
ice: dpll: fix phase offset value
ice: Shut down VSI with "link-down-on-close" enabled
ice: Fix link_down_on_close message
====================
Link: https://lore.kernel.org/r/20231227182541.3033124-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Intel Software Manual for I225, Section 7.5.2.7,
hicredit should be multiplied by the constant link-rate value, 0x7736.
Currently, the old constant link-rate value, 0x7735, from the boards
supported on igb are being used, most likely due to a copy'n'paste, as
the rest of the logic is the same for both drivers.
Update hicredit accordingly.
Fixes: 1ab011b0bf ("igc: Add support for CBS offloading")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Rodrigo Cataldo <rodrigo.cadore@l-acoustics.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Get link status version 2 (opcode 0x0607) is returning an error because FW
expects a data length of 56 bytes, and this is causing the driver to fail
probe.
Update the get link status version 2 data length to 56 bytes by adding 5
byte reserved5 field to the end of struct ice_aqc_get_link_status_data and
passing it as parameter to offsetofend() to the fix error.
Fixes: 2777d24ec6 ("ice: Add ice_get_link_status_datalen")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
During a PCI FLR the MSI-X Enable flag in the VF PCI MSI-X capability
register will be cleared. This can lead to issues when a VF is
assigned to a VM because in these cases the VF driver receives no
indication of the PF PCI error/reset and additionally it is incapable
of restoring the cleared flag in the hypervisor configuration space
without fully reinitializing the driver interrupt functionality.
Since the VF driver is unable to easily resolve this condition on its own,
restore the VF MSI-X flag during the PF PCI reset handling.
Fixes: 19b7960b2d ("i40e: implement split PCI error reset handler")
Co-developed-by: Karen Ostrowska <karen.ostrowska@intel.com>
Signed-off-by: Karen Ostrowska <karen.ostrowska@intel.com>
Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 3116f59c12 ("i40e: fix use-after-free in
i40e_sync_filters_subtask()") avoided use-after-free issues,
by increasing refcount during update the VSI filter list to
the HW. However, it missed the unicast situation.
When deleting an unicast FDB entry, the i40e driver will release
the mac_filter, and i40e_service_task will concurrently request
firmware to add the mac_filter, which will lead to the following
use-after-free issue.
Fix again for both netdev->uc and netdev->mc.
BUG: KASAN: use-after-free in i40e_aqc_add_filters+0x55c/0x5b0 [i40e]
Read of size 2 at addr ffff888eb3452d60 by task kworker/8:7/6379
CPU: 8 PID: 6379 Comm: kworker/8:7 Kdump: loaded Tainted: G
Workqueue: i40e i40e_service_task [i40e]
Call Trace:
dump_stack+0x71/0xab
print_address_description+0x6b/0x290
kasan_report+0x14a/0x2b0
i40e_aqc_add_filters+0x55c/0x5b0 [i40e]
i40e_sync_vsi_filters+0x1676/0x39c0 [i40e]
i40e_service_task+0x1397/0x2bb0 [i40e]
process_one_work+0x56a/0x11f0
worker_thread+0x8f/0xf40
kthread+0x2a0/0x390
ret_from_fork+0x1f/0x40
Allocated by task 21948:
kasan_kmalloc+0xa6/0xd0
kmem_cache_alloc_trace+0xdb/0x1c0
i40e_add_filter+0x11e/0x520 [i40e]
i40e_addr_sync+0x37/0x60 [i40e]
__hw_addr_sync_dev+0x1f5/0x2f0
i40e_set_rx_mode+0x61/0x1e0 [i40e]
dev_uc_add_excl+0x137/0x190
i40e_ndo_fdb_add+0x161/0x260 [i40e]
rtnl_fdb_add+0x567/0x950
rtnetlink_rcv_msg+0x5db/0x880
netlink_rcv_skb+0x254/0x380
netlink_unicast+0x454/0x610
netlink_sendmsg+0x747/0xb00
sock_sendmsg+0xe2/0x120
__sys_sendto+0x1ae/0x290
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0xa0/0x370
entry_SYSCALL_64_after_hwframe+0x65/0xca
Freed by task 21948:
__kasan_slab_free+0x137/0x190
kfree+0x8b/0x1b0
__i40e_del_filter+0x116/0x1e0 [i40e]
i40e_del_mac_filter+0x16c/0x300 [i40e]
i40e_addr_unsync+0x134/0x1b0 [i40e]
__hw_addr_sync_dev+0xff/0x2f0
i40e_set_rx_mode+0x61/0x1e0 [i40e]
dev_uc_del+0x77/0x90
rtnl_fdb_del+0x6a5/0x860
rtnetlink_rcv_msg+0x5db/0x880
netlink_rcv_skb+0x254/0x380
netlink_unicast+0x454/0x610
netlink_sendmsg+0x747/0xb00
sock_sendmsg+0xe2/0x120
__sys_sendto+0x1ae/0x290
__x64_sys_sendto+0xdd/0x1b0
do_syscall_64+0xa0/0x370
entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 3116f59c12 ("i40e: fix use-after-free in i40e_sync_filters_subtask()")
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Ke Xiao <xiaoke@sangfor.com.cn>
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: Di Zhu <zhudi2@huawei.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Although it does not seem to have any untoward side-effects,
the use of ';' to separate to assignments seems more appropriate than ','.
Flagged by clang-17 -Wcomma
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently, if a VF is disabled using the
'ip link set dev $ETHX vf $VF_NUM state disable' command, the VF is still
able to receive traffic.
Fix the behavior of the 'ip link set dev $ETHX vf $VF_NUM state disable'
to completely shutdown the VF's queues making it entirely disabled and
not able to receive or send any traffic.
Modify the behavior of the 'ip link set $ETHX vf $VF_NUM state enable'
command to make a VF do reinitialization bringing the queues back up.
Co-developed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Change returning codes to the kernel ones instead of
the internal ones for the entire ixgbe driver.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently ixgbe driver is notified of overheating events
via internal IXGBE_ERR_OVERTEMP error code.
Change the approach for handle_lasi() to use freshly introduced
is_overtemp function parameter which set when such event occurs.
Change check_overtemp() to bool and return true if overtemp
event occurs.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The link state of VF devices can be controlled via "ip link set", but the
current state (auto/disabled) is not reported by "ip link show".
Update ixgbe_ndo_get_vf_config() to make this info available to userspace.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add const modifier to function parameters and variables where appropriate
in ice_base.c and corresponding declarations in ice_base.h.
The reason for starting the change is that read-only pointers should be
marked as const when possible to allow for smoother and more optimal code
generation and optimization as well as allowing the compiler to warn the
developer about potentially unwanted modifications, while not carrying
noticeable negative impact.
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Sachin Bahadur <sachin.bahadur@intel.com>
Signed-off-by: Jan Glaza <jan.glaza@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It was found that this statistic is incorrectly
reported by HW and thus, useless.
As RX length error statistics are shown to the
end user when requested, the values reported
are misleading.
Thus, that value is no longer reported and
doesn't count anymore when adding all rx errors.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice_vf_create_vsi() function and its VF ops helper introduced by commit
a4c785e8162e ("ice: convert vf_ops .vsi_rebuild to .create_vsi") are used
during an individual VF reset to re-create the VSI. This was done in order
to ensure that the VSI gets properly reconfigured within the hardware.
This is somewhat heavy handed as we completely release the VSI memory and
structure, and then create a new VSI. This can also potentially force a
change of the VSI index as we will re-use the first open slot in the VSI
array which may not be the same.
As part of implementing devlink reload, commit 6624e780a5 ("ice: split
ice_vsi_setup into smaller functions") split VSI setup into smaller
functions, introducing both ice_vsi_cfg() and ice_vsi_decfg() which can be
used to configure or deconfigure an existing software VSI structure.
Rather than completely removing the VSI and adding a new one using the
.create_vsi() VF operation, simply use ice_vsi_decfg() to remove the
current configuration. Save the VSI type and then call ice_vsi_cfg() to
reconfigure the VSI as the same type that it was before.
The existing reset logic assumes that all hardware filters will be removed,
so also call ice_fltr_remove_all() before re-configuring the VSI.
This new operation does not re-create the VSI, so rename it to
ice_vf_reconfig_vsi().
The new approach can safely share the exact same flow for both SR-IOV VFs
as well as the Scalable IOV VFs being worked on. This uses less code and is
a better abstraction over fully deleting the VSI and adding a new one.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Petr Oros <poros@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Switchdev mode allows to add mirroring rules to mirror incoming and
outgoing packets to the interface's port representor. Previously, this was
available only using software functionality. Add possibility to offload
this functionality to the NIC hardware.
Introduce ICE_MIRROR_PACKET filter action to the ice_sw_fwd_act_type enum
to identify the desired action and pass it to the hardware as well as the
VSI to mirror.
Example of tc mirror command using hardware:
tc filter add dev ens1f0np0 ingress protocol ip prio 1 flower src_mac
b4:96:91:a5:c7:a7 skip_sw action mirred egress mirror dev eth1
ens1f0np0 - PF
b4:96:91:a5:c7:a7 - source MAC address
eth1 - PR of a VF to mirror to
Co-developed-by: Marcin Szycik <marcin.szycik@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Introduce new capability - Low Latency Timestamping with Interrupt.
On supported devices, driver can request a single timestamp from FW
without polling the register afterwards. Instead, FW can issue
a dedicated interrupt when the timestamp was read from the PHY register
and its value is available to read from the register.
This eliminates the need of bottom half scheduling, which results in
minimal delay for timestamping.
For this mode, allocate TS indices sequentially, so that timestamps are
always completed in FIFO manner.
Co-developed-by: Yochai Hagvi <yochai.hagvi@intel.com>
Signed-off-by: Yochai Hagvi <yochai.hagvi@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Schedule service task and EXTTS in the top half to avoid bottom half
scheduling if possible, which significantly reduces timestamping delay.
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the driver accepts VLAN EtherType steering rules regardless of
the configured mask. And things might fail silently or with confusing error
messages to the user. The VLAN EtherType can only be matched by full
mask. Therefore, add a check for that.
For instance the following rule is invalid, but the driver accepts it and
ignores the user specified mask:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 \
| m 0x00ff action 0
|Added rule with ID 63
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 63
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| VLAN EtherType: 0x8100 mask: 0x0
| VLAN: 0x0 mask: 0xffff
| User-defined: 0x0 mask: 0xffffffffffffffff
| Action: Direct to queue 0
After:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 \
| m 0x00ff action 0
|rmgr: Cannot insert RX class rule: Operation not supported
Fixes: 2b477d057e ("igc: Integrate flex filter into ethtool ops")
Suggested-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the driver accepts VLAN TCI steering rules regardless of the
configured mask. And things might fail silently or with confusing error
messages to the user.
There are two ways to handle the VLAN TCI mask:
1. Match on the PCP field using a VLAN prio filter
2. Match on complete TCI field using a flex filter
Therefore, add checks and code for that.
For instance the following rule is invalid and will be converted into a
VLAN prio rule which is not correct:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan 0x0001 m 0xf000 \
| action 1
|Added rule with ID 61
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 61
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| VLAN EtherType: 0x0 mask: 0xffff
| VLAN: 0x1 mask: 0x1fff
| User-defined: 0x0 mask: 0xffffffffffffffff
| Action: Direct to queue 1
After:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan 0x0001 m 0xf000 \
| action 1
|rmgr: Cannot insert RX class rule: Operation not supported
Fixes: 7991487ecb ("igc: Allow for Flex Filters to be installed")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently the driver allows to configure matching by VLAN EtherType.
However, the retrieval function does not report it back to the user. Add
it.
Before:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 action 0
|Added rule with ID 63
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 63
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| Action: Direct to queue 0
After:
|root@host:~# ethtool -N enp3s0 flow-type ether vlan-etype 0x8100 action 0
|Added rule with ID 63
|root@host:~# ethtool --show-ntuple enp3s0
|4 RX rings available
|Total 1 rules
|
|Filter: 63
| Flow Type: Raw Ethernet
| Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
| Ethertype: 0x0 mask: 0xFFFF
| VLAN EtherType: 0x8100 mask: 0x0
| VLAN: 0x0 mask: 0xffff
| User-defined: 0x0 mask: 0xffffffffffffffff
| Action: Direct to queue 0
Fixes: 2b477d057e ("igc: Integrate flex filter into ethtool ops")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Prevent VF from configuring filters with unsupported actions or use
REDIRECT action with invalid tc number. Current checks could cause
out of bounds access on PF side.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stop dividing the phase_offset value received from firmware. This fault
is present since the initial implementation.
The phase_offset value received from firmware is in 0.01ps resolution.
Dpll subsystem is using the value in 0.001ps, raw value is adjusted
before providing it to the user.
The user can observe the value of phase offset with response to
`pin-get` netlink message of dpll subsystem for an active pin:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-get --json '{"id":2}'
Where example of correct response would be:
{'board-label': 'C827_0-RCLKA',
'capabilities': 6,
'clock-id': 4658613174691613800,
'frequency': 1953125,
'id': 2,
'module-name': 'ice',
'parent-device': [{'direction': 'input',
'parent-id': 6,
'phase-offset': -216839550,
'prio': 9,
'state': 'connected'},
{'direction': 'input',
'parent-id': 7,
'phase-offset': -42930,
'prio': 8,
'state': 'connected'}],
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
'type': 'mux'}
Provided phase-offset value (-42930) shall be divided by the user with
DPLL_PHASE_OFFSET_DIVIDER to get actual value of -42.930 ps.
Before the fix, the response was not correct:
{'board-label': 'C827_0-RCLKA',
'capabilities': 6,
'clock-id': 4658613174691613800,
'frequency': 1953125,
'id': 2,
'module-name': 'ice',
'parent-device': [{'direction': 'input',
'parent-id': 6,
'phase-offset': -216839,
'prio': 9,
'state': 'connected'},
{'direction': 'input',
'parent-id': 7,
'phase-offset': -42,
'prio': 8,
'state': 'connected'}],
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
'type': 'mux'}
Where phase-offset value (-42), after division
(DPLL_PHASE_OFFSET_DIVIDER) would be: -0.042 ps.
Fixes: 8a3a565ff2 ("ice: add admin commands to access cgu configuration")
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Disabling netdev with ethtool private flag "link-down-on-close" enabled
can cause NULL pointer dereference bug. Shut down VSI regardless of
"link-down-on-close" state.
Fixes: 8ac7132704 ("ice: Fix interface being down after reset with link-down-on-close flag on")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver should not report an error message when for a medialess port
the link_down_on_close flag is enabled and the physical link cannot be
set down.
Fixes: 8ac7132704 ("ice: Fix interface being down after reset with link-down-on-close flag on")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Katarzyna Wieczerzycka <katarzyna.wieczerzycka@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Size of the virtchnl2_rss_key struct should be 7 bytes but the
compiler introduces a padding byte for the structure alignment.
This results in idpf sending an additional byte of memory to the device
control plane than the expected buffer size. As the control plane
enforces virtchnl message size checks to validate the message,
set RSS key message fails resulting in the driver load failure.
Remove implicit compiler padding by using "__packed" structure
attribute for the virtchnl2_rss_key struct.
Also there is no need to use __DECLARE_FLEX_ARRAY macro for the
'key_flex' struct field. So drop it.
Fixes: 0d7502a9b4 ("virtchnl: add virtchnl version 2 ops")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Scott Register <scott.register@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
idpf_ring::skb serves only for keeping an incomplete frame between
several NAPI Rx polling cycles, as one cycle may end up before
processing the end of packet descriptor. The pointer is taken from
the ring onto the stack before entering the loop and gets written
there after the loop exits. When inside the loop, only the onstack
pointer is used.
For some reason, the logics is broken in the singleq mode, where the
pointer is taken from the ring each iteration. This means that if a
frame got fragmented into several descriptors, each fragment will have
its own skb, but only the last one will be passed up the stack
(containing garbage), leaving the rest leaked.
Then, on ifdown, rxq::skb is being freed only in the splitq mode, while
it can point to a valid skb in singleq as well. This can lead to a yet
another skb leak.
Just don't touch the ring skb field inside the polling loop, letting
the onstack skb pointer work as expected: build a new skb if it's the
first frame descriptor and attach a frag otherwise. On ifdown, free
rxq::skb unconditionally if the pointer is non-NULL.
Fixes: a5ab9ee0df ("idpf: add singleq start_xmit and napi poll")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Scott Register <scott.register@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
intel: use bitfield operations
Jesse Brandeburg says:
After repeatedly getting review comments on new patches, and sporadic
patches to fix parts of our drivers, we should just convert the Intel code
to use FIELD_PREP() and FIELD_GET(). It's then "common" in the code and
hopefully future change-sets will see the context and do-the-right-thing.
This conversion was done with a coccinelle script which is mentioned in the
commit messages. Generally there were only a couple conversions that were
"undone" after the automatic changes because they tried to convert a
non-contiguous mask.
Patch 1 is required at the beginning of this series to fix a "forever"
issue in the e1000e driver that fails the compilation test after conversion
because the shift / mask was out of range.
The second patch just adds all the new #includes in one go.
The patch titled: "ice: fix pre-shifted bit usage" is needed to allow the
use of the FIELD_* macros and fix up the unexpected "shifts included"
defines found while creating this series.
The rest are the conversion to use FIELD_PREP()/FIELD_GET(), and the
occasional leXX_{get,set,encode}_bits() call, as suggested by Alex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=stU2
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-12-18
This PR is larger than usual and contains changes in various parts
of the kernel.
The main changes are:
1) Fix kCFI bugs in BPF, from Peter Zijlstra.
End result: all forms of indirect calls from BPF into kernel
and from kernel into BPF work with CFI enabled. This allows BPF
to work with CONFIG_FINEIBT=y.
2) Introduce BPF token object, from Andrii Nakryiko.
It adds an ability to delegate a subset of BPF features from privileged
daemon (e.g., systemd) through special mount options for userns-bound
BPF FS to a trusted unprivileged application. The design accommodates
suggestions from Christian Brauner and Paul Moore.
Example:
$ sudo mkdir -p /sys/fs/bpf/token
$ sudo mount -t bpf bpffs /sys/fs/bpf/token \
-o delegate_cmds=prog_load:MAP_CREATE \
-o delegate_progs=kprobe \
-o delegate_attachs=xdp
3) Various verifier improvements and fixes, from Andrii Nakryiko, Andrei Matei.
- Complete precision tracking support for register spills
- Fix verification of possibly-zero-sized stack accesses
- Fix access to uninit stack slots
- Track aligned STACK_ZERO cases as imprecise spilled registers.
It improves the verifier "instructions processed" metric from single
digit to 50-60% for some programs.
- Fix verifier retval logic
4) Support for VLAN tag in XDP hints, from Larysa Zaremba.
5) Allocate BPF trampoline via bpf_prog_pack mechanism, from Song Liu.
End result: better memory utilization and lower I$ miss for calls to BPF
via BPF trampoline.
6) Fix race between BPF prog accessing inner map and parallel delete,
from Hou Tao.
7) Add bpf_xdp_get_xfrm_state() kfunc, from Daniel Xu.
It allows BPF interact with IPSEC infra. The intent is to support
software RSS (via XDP) for the upcoming ipsec pcpu work.
Experiments on AWS demonstrate single tunnel pcpu ipsec reaching
line rate on 100G ENA nics.
8) Expand bpf_cgrp_storage to support cgroup1 non-attach, from Yafang Shao.
9) BPF file verification via fsverity, from Song Liu.
It allows BPF progs get fsverity digest.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (164 commits)
bpf: Ensure precise is reset to false in __mark_reg_const_zero()
selftests/bpf: Add more uprobe multi fail tests
bpf: Fail uprobe multi link with negative offset
selftests/bpf: Test the release of map btf
s390/bpf: Fix indirect trampoline generation
selftests/bpf: Temporarily disable dummy_struct_ops test on s390
x86/cfi,bpf: Fix bpf_exception_cb() signature
bpf: Fix dtor CFI
cfi: Add CFI_NOSEAL()
x86/cfi,bpf: Fix bpf_struct_ops CFI
x86/cfi,bpf: Fix bpf_callback_t CFI
x86/cfi,bpf: Fix BPF JIT call
cfi: Flip headers
selftests/bpf: Add test for abnormal cnt during multi-kprobe attachment
selftests/bpf: Don't use libbpf_get_error() in kprobe_multi_test
selftests/bpf: Add test for abnormal cnt during multi-uprobe attachment
bpf: Limit the number of kprobes when attaching program to multiple kprobes
bpf: Limit the number of uprobes when attaching program to multiple uprobes
bpf: xdp: Register generic_kfunc_set with XDP programs
selftests/bpf: utilize string values for delegate_xxx mount options
...
====================
Link: https://lore.kernel.org/r/20231219000520.34178-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most of idpf correctly uses FIELD_GET and FIELD_PREP, but a couple spots
were missed so fix those.
Automated conversion with coccinelle script and manually fixed up,
including audits for opportunities to convert to {get,encode,replace}
bits functions.
Add conversions to le16_get/encode/replace_bits where appropriate. And
in one place fix up a cast from a u16 to a u16.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
@get@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It was found while doing further testing of the previous commit
fbf32a9bab91 ("ice: field get conversion") that one of the FIELD_GET
conversions should really be a FIELD_PREP. The previous code was styled
as a match to the FIELD_GET conversion, which always worked because the
shift value was 0. The code makes way more sense as a FIELD_PREP and
was in fact the only FIELD_GET with two constant arguments in this
series.
Didn't squash this patch to make it easier to call out the
(non-impactful) bug.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the ice driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the iavf driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@get@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the i40e driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
While making one of the conversions, an if() check was inverted to
return early and avoid un-necessary indentation of the remainder of the
function. In some other cases a stack variable was moved inside the
block where it was used while doing cleanups/review.
A couple places were changed to use le16_get_bits() instead of FIELD_GET
with a le16_to_cpu combination.
@get@
constant shift,mask;
metavariable type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the igc driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@get@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor several older Intel drivers to use FIELD_GET(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
(
-((T)((a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor igc driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired in a later patch.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor ice driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Several places I changed to OR into a single variable with |= instead of
using a multi-line statement with trailing OR operators, as it
(subjectively) makes the code clearer.
A local variable vmvf_and_timeout was created and used to avoid multiple
logical ORs being __le16 converted, which shortened some lines and makes
the code cleaner.
Also clean up a couple of places where conversions were made to have the
code read more clearly/consistently.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor iavf driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Clean up a couple spots in the code that had repetitive
y = cpu_to_*((blah << blah_blah) & blat)
y |= cpu_to_*((blahs << blahs_blahs) & blats)
to
x = FIELD_PREP(blat blah)
x |= FIELD_PREP(blats, blahs)
y = cpu_to_*(x);
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Cc: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor i40e driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Refactor one function with multiple if's to return quickly to make lines
fit in 80 columns.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor several older Intel drivers to use FIELD_PREP(), which reduces
lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This series is introducing the use of FIELD_GET and FIELD_PREP which
requires bitfield.h to be included. Fix all the includes in this one
change, and rearrange includes into alphabetical order to ease
readability and future maintenance.
virtchnl.h and it's usage was modified to have it's own includes as it
should. This required including bits.h for virtchnl.h.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
For more than 15 years this code has passed in a request for a page and
masked off that page when read/writing. This code has been here forever,
but FIELD_PREP finds the bug when converted to use it. Change the code
to do exactly the same thing but allow the conversion to FIELD_PREP in a
later patch. To make it clear what we lost when making this change I
left a comment, but there is no point to change the code to generate a
correct sequence at this point.
This is not a Fixes tagged patch on purpose because it doesn't change
the binary output.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 6624e780a5 ("ice: split ice_vsi_setup into smaller
functions") has refactored a bunch of code involved in PFR. In this
process, TC queue number adjustment for XDP was lost. Bring it back.
Lack of such adjustment causes interface to go into no-carrier after a
reset, if XDP program is attached, with the following message:
ice 0000:b1:00.0: Failed to set LAN Tx queue context, error: -22
ice 0000:b1:00.0 ens801f0np0: Failed to open VSI 0x0006 on switch 0x0001
ice 0000:b1:00.0: enable VSI failed, err -22, VSI index 0, type ICE_VSI_PF
ice 0000:b1:00.0: PF VSI rebuild failed: -22
ice 0000:b1:00.0: Rebuild failed, unload and reload driver
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously, the ice driver had support for using a handler for bonding
netdev events to ensure that conflicting features were not allowed to be
activated at the same time. While this was still in place, additional
support was added to specifically support SRIOV and LAG together. These
both utilized the netdev event handler, but the SRIOV and LAG feature was
behind a capabilities feature check to make sure the current NVM has
support.
The exclusion part of the event handler should be removed since there are
users who have custom made solutions that depend on the non-exclusion of
features.
Wrap the creation/registration and cleanup of the event handler and
associated structs in the probe flow with a feature check so that the
only systems that support the full implementation of LAG features will
initialize support. This will leave other systems unhindered with
functionality as it existed before any LAG code was added.
Fixes: bb52f42ace ("ice: Add driver support for firmware changes for LAG")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When creating new VSIs, they are assigned into an aggregator node in the
scheduler tree. Information about which aggregator node a VSI is assigned
into is maintained by the vsi->agg_node structure. In ice_vsi_decfg(), this
information is being destroyed, by overwriting the valid flag and the
agg_id field to zero.
For VF VSIs, this breaks the aggregator node configuration replay, which
depends on this information. This results in VFs being inserted into the
default aggregator node. The resulting configuration will have unexpected
Tx bandwidth sharing behavior.
This was broken by commit 6624e780a5 ("ice: split ice_vsi_setup into
smaller functions"), which added the block to reset the agg_node data.
The vsi->agg_node structure is not managed by the scheduler code, but is
instead a wrapper around an aggregator node ID that is tracked at the VSI
layer. Its been around for a long time, and its primary purpose was for
handling VFs. The SR-IOV VF reset flow does not make use of the standard VSI
rebuild/replay logic, and uses vsi->agg_node as part of its handling to
rebuild the aggregator node configuration.
The logic for aggregator nodes stretches back to early ice driver code from
commit b126bd6bcd ("ice: create scheduler aggregator node config and move
VSIs")
The logic in ice_vsi_decfg() which trashes the ice_agg_node data is clearly
wrong. It destroys information that is necessary for handling VF reset,. It
is also not the correct way to actually remove a VSI from an aggregator
node. For that, we need to implement logic in the scheduler code. Further,
non-VF VSIs properly replay their aggregator configuration using existing
scheduler replay logic.
To fix the VF replay logic, remove this broken aggregator node cleanup
logic. This is the simplest way to immediately fix this.
This ensures that VFs will have proper aggregate configuration after a
reset. This is especially important since VFs often perform resets as part
of their reconfiguration flows. Without fixing this, VFs will be placed in
the default aggregator node and Tx bandwidth will not be shared in the
expected and configured manner.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
add v2 FW logging for ice driver
Paul Stillwell says:
Firmware (FW) log support was added to the ice driver, but that version is
no longer supported. There is a newer version of FW logging (v2) that
adds more control knobs to get the exact data out of the FW
for debugging.
The interface for FW logging is debugfs. This was chosen based on
discussions here:
https://lore.kernel.org/netdev/20230214180712.53fc8ba2@kernel.org/ and
https://lore.kernel.org/netdev/20231012164033.1069fb4b@kernel.org/
We talked about using devlink in a variety of ways, but none of those
options made any sense for the way the FW reports data. We briefly talked
about using ethtool, but that seemed to go by the wayside. Ultimately it
seems like using debugfs is the way to go so re-implement the code to use
that.
FW logging is across all the PFs on the device so restrict the commands to
only PF0.
If the device supports FW logging then a directory named 'fwlog' will be
created under '/sys/kernel/debug/ice/<pci_dev>'. A variety of files will be
created to manage the behavior of logging. The following files will be
created:
- modules/<module>
- nr_messages
- enable
- log_size
- data
where
modules/<module> is used to read/write the log level for a specific module
nr_messages is used to determine how many events should be in each message
sent to the driver
enable is used to start/stop FW logging. This is a boolean value so only 1
or 0 are permissible values
log_size is used to configure the amount of memory the driver uses for log
data
data is used to read/clear the log data
Generally there is a lot of data and dumping that data to syslog will
result in a loss of data. This causes problems when decoding the data and
the user doesn't know that data is missing until later. Instead of dumping
the FW log output to syslog use debugfs. This ensures that all the data the
driver has gets retrieved correctly.
The FW log data is binary data that the FW team decodes to determine what
happened in firmware. The binary blob is sent to Intel for decoding.
---
v6:
- use seq_printf() for outputting module info when reading from 'module' file
- replace code that created argc and argv for handling command line input
- removed checks in all the _read() and _write() functions to see if FW logging
is supported because the files will not exist if it is not supported
- removed warnings on allocation failures on debugfs file creation failures
- removed a newline between memory allocation and checking if the memory was
allocated
- fixed cases where we could just return the value from a function call
instead of saving the value in a variable
- moved the check for PFO in ice_fwlog_init() to an earlier patch
- reworked all of argument scanning in the _write() functions in ice_debugfs.c
to remove adding characters past the end of the buffer
v5: https://lore.kernel.org/netdev/20231205211251.2122874-1-anthony.l.nguyen@intel.com/
- changed the log level configuration from a single file for all modules to a
file per module.
- changed 'nr_buffs' to 'log_size' because users understand memory sizes
better than a number of buffers
- changed 'resolution' to 'nr_messages' to better reflect what it represents
- updated documentation to reflect these changes
- updated documentation to indicate that FW logging must be disabled to
clear the data. also clarified that any value written to the 'data' file will
clear the data
v4: https://lore.kernel.org/netdev/20231005170110.3221306-1-anthony.l.nguyen@intel.com/
- removed CONFIG_DEBUG_FS wrapper around code because the debugfs calls handle
this case already
- moved ice_debugfs_exit() call to remove unreachable code issue
- minor changes to documentation based on feedback
v3: https://lore.kernel.org/netdev/20230815165750.2789609-1-anthony.l.nguyen@intel.com/
- Adjust error path cleanup in ice_module_init() for unreachable code.
v2: https://lore.kernel.org/netdev/20230810170109.1963832-1-anthony.l.nguyen@intel.com/
- Rewrote code to use debugfs instead of devlink
v1: https://lore.kernel.org/netdev/20230209190702.3638688-1-anthony.l.nguyen@intel.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-12-13 (ice, i40e)
This series contains updates to ice and i40e drivers.
Michal Schmidt prevents possible out-of-bounds access for ice.
Ivan Vecera corrects value for MDIO clause 45 on i40e.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix ST code value for Clause 45
ice: fix theoretical out-of-bounds access in ethtool link modes
====================
Link: https://lore.kernel.org/r/20231213220827.1311772-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since we never support this feature for I40E driver, we don't have to
display the value when using 'ethtool -c eth0'.
Before this patch applied, the rx-frames-irq is 256 which is consistent
with tx-frames-irq. Apparently it could mislead users.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231213184406.1306602-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Once logging is enabled the user should read the data from the 'data'
file. The data is in the form of a binary blob that can be sent to Intel
for decoding. To read the data use a command like:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/data > log_data.bin
If the user wants to clear the FW log data that has been stored in the
driver then they can write any value to the 'data' file and that will clear
the data. An example is:
# echo 34 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/data
In addition to being able to read the data the user can configure how
much memory is used to store FW log data. This allows the user to
increase/decrease the amount of memory based on the users situation.
The data is stored such that if the memory fills up then the oldest data
will get overwritten in a circular manner. To change the amount of
memory the user can write to the 'log_size' file like this:
# echo <value> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/log_size
Where <value> is one of 128K, 256K, 512K, 1M, and 2M. The default value
is 1M.
The user can see the current value of 'log_size' by reading the file:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/log_size
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Once users have configured the FW logging then allow them to enable it
by writing to the 'fwlog/enable' file. The file accepts a boolean value
(0 or 1) where 1 means enable FW logging and 0 means disable FW logging.
# echo <value> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/enable
Where <value> is 0 or 1.
The user can read the 'fwlog/enable' file to see whether logging is
enabled or not. Reading the actual data is a separate patch. To see the
current value then:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/enable
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Users want the ability to debug FW issues by retrieving the
FW logs from the E8xx devices. Use debugfs to allow the user to
configure the log level and number of messages for FW logging.
If FW logging is supported on the E8xx then the file 'fwlog' will be
created under the PCI device ID for the ice driver. If the file does not
exist then either the E8xx doesn't support FW logging or debugfs is not
enabled on the system.
One thing users want to do is control which events are reported. The
user can read and write the 'fwlog/modules/<module name>' to get/set
the log levels. Each module in the FW that supports logging ht as a file
under 'fwlog/modules' that supports reading (to see what the current log
level is) and writing (to change the log level).
The format to set the log levels for a module are:
# echo <log level> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/<module>
The supported log levels are:
* none
* error
* warning
* normal
* verbose
Each level includes the messages from the previous/lower level
The modules that are supported are:
* general
* ctrl
* link
* link_topo
* dnl
* i2c
* sdp
* mdio
* adminq
* hdma
* lldp
* dcbx
* dcb
* xlr
* nvm
* auth
* vpd
* iosf
* parser
* sw
* scheduler
* txq
* rsvd
* post
* watchdog
* task_dispatch
* mng
* synce
* health
* tsdrv
* pfreg
* mdlver
* all
The module 'all' is a special module which allows the user to read or
write to all of the modules.
The following example command would set the DCB module to the 'normal'
log level:
# echo normal > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
If the user wants to set the DCB, Link, and the AdminQ modules to
'verbose' then the commands are:
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/link
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/adminq
If the user wants to set all modules to the 'warning' level then the
command is:
# echo warning > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
If the user wants to disable logging for a module then they can set the
level to 'none'. An example setting the 'watchdog' module is:
# echo none > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/watchdog
If the user wants to see what the log level is for a specific module
then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
This will return the log level for the DCB module. If the user wants to
see the log level for all the modules then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
Writing to the module file will update the configuration, but NOT enable the
configuration (that is a separate command).
In addition to configuring the modules, the user can also configure the
number of log messages (nr_messages) to include in a single Admin Receive
Queue (ARQ) event.The range is 1-128 (1 means push every log message, 128
means push only when the max AQ command buffer is full). The suggested
value is 10.
To see/change the resolution the user can read/write the
'fwlog/nr_messages' file. An example changing the value to 50 is
# echo 50 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
To see the current value of 'nr_messages' then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The FW logging code doesn't work because there is no way to set
cq_ena or uart_ena so remove the code. This code is the original
(v1) way of FW logging so it should be replaced with the v2 way.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-12-12 (igb, e1000e)
This series contains updates to igb and e1000e drivers.
Ilpo Järvinen does some cleanups to both drivers: utilizing FIELD_GET()
helpers and using standard kernel defines over driver created ones.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
e1000e: Use pcie_capability_read_word() for reading LNKSTA
e1000e: Use PCI_EXP_LNKSTA_NLW & FIELD_GET() instead of custom defines/code
igb: Use FIELD_GET() to extract Link Width
====================
Link: https://lore.kernel.org/r/20231212204947.513563-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to set the symmetric Toeplitz hash function via:
# ethtool -X eth0 hfunc toeplitz symmetric-xor
The driver will reject any new RSS configuration if a field other than
(IP src/dst and L4 src/dst ports) is requested for hashing.
The symmetric RSS will not be supported on PFs not advertising the ADV RSS
Offload flag (ADV_RSS_SUPPORT()), for example the E700 series (i40e).
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-9-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to set the symmetric Toeplitz hash function via:
# ethtool -X eth0 hfunc toeplitz symmetric-xor
All existing RSS configurations will be converted to symmetric unless they
have a non-symmetric field (other than IP src/dst and L4 src/dst ports)
used for hashing. The driver will reject a new RSS configuration if such
a field is requested.
The hash function in the E800 NICs is set per-VSI and a specific AQ
command is needed to modify the hash function. Use the AQ command to
enable setting the symmetric Toeplitz RSS hash function for any VSI
in the new ice_set_rss_hfunc().
When the Symmetric Toeplitz hash function is used, the hardware sets the
input set of the RSS (Toeplitz) algorithm to be the XOR of the fields
index by HSYMM and the fields index by the INSET registers. We use this
to create a symmetric hash by setting the HSYMM registers to point to
their counterparts in the INSET registers:
HSYMM [src_fv] = dst_fv;
HSYMM [dst_fv] = src_fv;
where src_fv and dst_fv are the indexes of the protocol's src and dst
fields.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-8-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The flow director and RSS blocks use separate methods to generate a
unique 64 bit ID for the flow. This is not extendable, especially for
the RSS that already uses all 64 bit space.
Refactor the flow generation API so that the ID is generated within
ice_flow_add_prof(). The FD and RSS blocks caches the generated ID for
later use.
Suggested-by: Dan Nowlin <dan.nowlin@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-7-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor the driver to use a communication data structure for RSS
config. To do so we introduce the new ice_rss_hash_cfg struct, and then
pass it as an argument to several functions.
Also introduce enum ice_rss_cfg_hdr_type to specify a more granular and
flexible RSS configuration:
ICE_RSS_OUTER_HEADERS - take outer layer as RSS input set
ICE_RSS_INNER_HEADERS - take inner layer as RSS input set
ICE_RSS_INNER_HEADERS_W_OUTER_IPV4 - take inner layer as RSS input set for
packet with outer IPV4
ICE_RSS_INNER_HEADERS_W_OUTER_IPV6 - take inner layer as RSS input set for
packet with outer IPV6
ICE_RSS_ANY_HEADERS - try with outer first then inner (same as the
behaviour without this change)
Finally, move the virtchnl_rss_algorithm enum to be with the other RSS
related structures in the virtchnl.h file.
There should be no functional change due to this patch.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-6-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the values of the ICE_AQ_VSI_Q_OPT_RSS_* registers. Shifting is
already done when the values are used, no need to double shift. Bug was
not discovered earlier since only ICE_AQ_VSI_Q_OPT_RSS_TPLZ (Zero) is
currently used.
Also, rename ICE_AQ_VSI_Q_OPT_RSS_XXX to ICE_AQ_VSI_Q_OPT_RSS_HASH_XXX
for consistency.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-5-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the RSS context parameters to struct ethtool_rxfh_param and use the
get/set_rxfh to handle the RSS contexts as well.
This is part 2/2 of the fix suggested in [1]:
- Add a rss_context member to the argument struct and a capability
like cap_link_lanes_supported to indicate whether driver supports
rss contexts, then you can remove *et_rxfh_context functions,
and instead call *et_rxfh() with a non-zero rss_context.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Tony Nguyen <anthony.l.nguyen@intel.com>
CC: Marcin Wojtas <mw@semihalf.com>
CC: Russell King <linux@armlinux.org.uk>
CC: Sunil Goutham <sgoutham@marvell.com>
CC: Geetha sowjanya <gakula@marvell.com>
CC: Subbaraya Sundeep <sbhatta@marvell.com>
CC: hariprasad <hkelam@marvell.com>
CC: Saeed Mahameed <saeedm@nvidia.com>
CC: Leon Romanovsky <leon@kernel.org>
CC: Edward Cree <ecree.xilinx@gmail.com>
CC: Martin Habets <habetsm.xilinx@gmail.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-3-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
idpf supports the header split feature and that feature is always
enabled by default.
However, for flexibility reasons and to simplify some scenarios, it
would be useful to have the support for switching the header split
off (and on) from the userspace.
Address that need by adding the user config parameter, the functions
for disabling (or enabling) the header split feature, and calls to
them from the Ethtool ringparam callbacks.
It still is enabled by default if supported by the hardware.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Co-developed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20231212142752.935000-3-aleksander.lobakin@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VLAN proto, used in ice XDP hints implementation is stored in ring packet
context. Utilize this value in skb VLAN processing too instead of checking
netdev features.
At the same time, use vlan_tci instead of vlan_tag in touched code,
because VLAN tag often refers to VLAN proto and VLAN TCI combined,
while in the code we clearly store only VLAN TCI.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-12-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Implement .xmo_rx_vlan_tag callback to allow XDP code to read
packet's VLAN tag.
At the same time, use vlan_tci instead of vlan_tag in touched code,
because VLAN tag often refers to VLAN proto and VLAN TCI combined,
while in the code we clearly store only VLAN TCI.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-11-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In AF_XDP ZC, xdp_buff is not stored on ring,
instead it is provided by xsk_buff_pool.
Space for metadata sources right after such buffers was already reserved
in commit 94ecc5ca4d ("xsk: Add cb area to struct xdp_buff_xsk").
Some things (such as pointer to packet context) do not change on a
per-packet basis, so they can be set at the same time as RX queue info.
On the other hand, RX descriptor is unique for each packet, but is already
known when setting DMA addresses. This minimizes performance impact of
hints on regular packet processing.
Update AF_XDP ZC packet processing to support XDP hints.
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-9-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
RX hash XDP hint requests both hash value and type.
Type is XDP-specific, so we need a separate way to map
these values to the hardware ptypes, so create a lookup table.
Instead of creating a new long list, reuse contents
of ice_decode_rx_desc_ptype[] through preprocessor.
Current hash type enum does not contain ICMP packet type,
but ice devices support it, so also add a new type into core code.
Then use previously refactored code and create a function
that allows XDP code to read RX hash.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-7-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Use previously refactored code and create a function
that allows XDP code to read HW timestamp.
Also, introduce packet context, where hints-related data will be stored.
ice_xdp_buff contains only a pointer to this structure, to avoid copying it
in ZC mode later in the series.
HW timestamp is the first supported hint in the driver,
so also add xdp_metadata_ops.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-6-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In order to use XDP hints via kfuncs we need to put
RX descriptor and miscellaneous data next to xdp_buff.
Same as in hints implementations in other drivers, we achieve
this through putting xdp_buff into a child structure.
Currently, xdp_buff is stored in the ring structure,
so replace it with union that includes child structure.
This way enough memory is available while existing XDP code
remains isolated from hints.
Minimum size of the new child structure (ice_xdp_buff) is exactly
64 bytes (single cache line). To place it at the start of a cache line,
move 'next' field from CL1 to CL4, as it isn't used often. This still
leaves 192 bits available in CL3 for packet context extensions.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-5-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, rx_ptype variable is used only as an argument
to ice_process_skb_fields() and is computed
just before the function call.
Therefore, there is no reason to pass this value as an argument.
Instead, remove this argument and compute the value directly inside
ice_process_skb_fields() function.
Also, separate its calculation into a short function, so the code
can later be reused in .xmo_() callbacks.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-4-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Previously, we only needed RX HW timestamp in skb path,
hence all related code was written with skb in mind.
But with the addition of XDP hints via kfuncs to the ice driver,
the same logic will be needed in .xmo_() callbacks.
Put generic process of reading RX HW timestamp from a descriptor
into a separate function.
Move skb-related code into another source file.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-3-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Previously, we only needed RX hash in skb path,
hence all related code was written with skb in mind.
But with the addition of XDP hints via kfuncs to the ice driver,
the same logic will be needed in .xmo_() callbacks.
Separate generic process of reading RX hash from a descriptor
into a separate function.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-2-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
ST code value for clause 45 that has been changed by
commit 8196b5fd6c ("i40e: Refactor I40E_MDIO_CLAUSE* macros")
is currently wrong.
The mentioned commit refactored ..MDIO_CLAUSE??_STCODE_MASK so
their value is the same for both clauses. The value is correct
for clause 22 but not for clause 45.
Fix the issue by adding a parameter to I40E_GLGEN_MSCA_STCODE_MASK
macro that specifies required value.
Fixes: 8196b5fd6c ("i40e: Refactor I40E_MDIO_CLAUSE* macros")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
To map phy types reported by the hardware to ethtool link mode bits,
ice uses two lookup tables (phy_type_low_lkup, phy_type_high_lkup).
The "low" table has 64 elements to cover every possible bit the hardware
may report, but the "high" table has only 13. If the hardware reports a
higher bit in phy_types_high, the driver would access memory beyond the
lookup table's end.
Instead of iterating through all 64 bits of phy_types_{low,high}, use
the sizes of the respective lookup tables.
Fixes: 9136e1f1e5 ("ice: refactor PHY type to ethtool link mode")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mode supported is currently reported to the user exactly the same, as
the current mode. That's because mode changing is not implemented.
Remove the leftover mode_supported() op and use mode_get() to fill up
the supported mode exposed to user.
One, if even, mode changing is going to be introduced, this could be
very easily taken back. In the meantime, prevent drivers form
implementing this in wrong way (as for example recent netdevsim
implementation attempt intended to do).
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pcie_capability_read_word() for reading LNKSTA and remove the
custom define that matches to PCI_EXP_LNKSTA.
As only single user for cap_offset remains, replace it with a call to
pci_pcie_cap(). Instead of e1000_adapter, make local variable out of
pci_dev because both users are interested in it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make the flow for pci shutdown be the same to the pci remove.
iavf_shutdown was implementing an incomplete version
of iavf_remove. It misses several calls to the kernel like
iavf_free_misc_irq, iavf_reset_interrupt_capability, iounmap
that might break the system on reboot or hibernation.
Implement the call of iavf_remove directly in iavf_shutdown to
close this gap.
Fixes below error messages (dmesg) during shutdown stress tests -
[685814.900917] ice 0000:88:00.0: MAC 02:d0:5f:82:43:5d does not exist for
VF 0
[685814.900928] ice 0000:88:00.0: MAC 33:33:00:00:00:01 does not exist for
VF 0
Reproduction:
1. Create one VF interface:
echo 1 > /sys/class/net/<interface_name>/device/sriov_numvfs
2. Run live dmesg on the host:
dmesg -wH
3. On SUT, script below steps into vf_namespace_assignment.sh
<#!/bin/sh> // Remove <>. Git removes # line
if=<VF name> (edit this per VF name)
loop=0
while true; do
echo test round $loop
let loop++
ip netns add ns$loop
ip link set dev $if up
ip link set dev $if netns ns$loop
ip netns exec ns$loop ip link set dev $if up
ip netns exec ns$loop ip link set dev $if netns 1
ip netns delete ns$loop
done
4. Run the script for at least 1000 iterations on SUT:
./vf_namespace_assignment.sh
Expected result:
No errors in dmesg.
Fixes: 129cf89e58 ("iavf: rename functions and structs to new name")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Ranganatha Rao <ranganatha.rao@intel.com>
Signed-off-by: Ranganatha Rao <ranganatha.rao@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ntuple-filter feature on/off:
Default is on. If turned off, the filters will be removed from both
PF and iavf list. The removal is irrespective of current filter state.
Steps to reproduce:
-------------------
1. Ensure ntuple is on.
ethtool -K enp8s0 ntuple-filters on
2. Create a filter to receive the traffic into non-default rx-queue like 15
and ensure traffic is flowing into queue into 15.
Now, turn off ntuple. Traffic should not flow to configured queue 15.
It should flow to default RX queue.
Fixes: 0dbfbabb84 ("iavf: Add framework to enable ethtool ntuple filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Ranganatha Rao <ranganatha.rao@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
New states introduced:
IAVF_FDIR_FLTR_DIS_REQUEST
IAVF_FDIR_FLTR_DIS_PENDING
IAVF_FDIR_FLTR_INACTIVE
Current FDIR state machines (SM) are not adequate to handle a few
scenarios in the link DOWN/UP event, reset event and ntuple-feature.
For example, when VF link goes DOWN and comes back UP administratively,
the expectation is that previously installed filters should also be
restored. But with current SM, filters are not restored.
So with new SM, during link DOWN filters are marked as INACTIVE in
the iavf list but removed from PF. After link UP, SM will transition
from INACTIVE to ADD_REQUEST to restore the filter.
Similarly, with VF reset, filters will be removed from the PF, but
marked as INACTIVE in the iavf list. Filters will be restored after
reset completion.
Steps to reproduce:
-------------------
1. Create a VF. Here VF is enp8s0.
2. Assign IP addresses to VF and link partner and ping continuously
from remote. Here remote IP is 1.1.1.1.
3. Check default RX Queue of traffic.
ethtool -S enp8s0 | grep -E "rx-[[:digit:]]+\.packets"
4. Add filter - change default RX Queue (to 15 here)
ethtool -U ens8s0 flow-type ip4 src-ip 1.1.1.1 action 15 loc 5
5. Ensure filter gets added and traffic is received on RX queue 15 now.
Link event testing:
-------------------
6. Bring VF link down and up. If traffic flows to configured queue 15,
test is success, otherwise it is a failure.
Reset event testing:
--------------------
7. Reset the VF. If traffic flows to configured queue 15, test is success,
otherwise it is a failure.
Fixes: 0dbfbabb84 ("iavf: Add framework to enable ethtool ntuple filters")
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Ranganatha Rao <ranganatha.rao@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
e1000e has own copy of PCI Negotiated Link Width field defines. Use the
ones from include/uapi/linux/pci_regs.h instead of the custom ones and
remove the custom ones and convert to FIELD_GET().
Suggested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __iavf_set_coalesce, the driver checks both ec->rx_coalesce_usecs and
ec->tx_coalesce_usecs for validity. It does this via a chain if if/else-if
blocks. If every single branch of the series of if statements exited, this
would be fine. However, the rx_coalesce_usecs is checked against zero to
print an informative message if use_adaptive_rx_coalesce is enabled. If
this check is true, it short circuits the entire chain of statements,
preventing validation of the tx_coalesce_usecs field.
Indeed, since commit e792779e6b ("iavf: Prevent changing static ITR
values if adaptive moderation is on") the iavf driver actually rejects any
change to the tx_coalesce_usecs or rx_coalesce_usecs when
use_adaptive_tx_coalesce or use_adaptive_rx_coalesce is enabled, making
this checking a bit redundant.
Fix this error by removing the unnecessary and redundant checks for
use_adaptive_rx_coalesce and use_adaptive_tx_coalesce. Since zero is a
valid value, and since the tx_coalesce_usecs and rx_coalesce_usecs fields
are already unsigned, remove the minimum value check. This allows assigning
an ITR value ranging from 0-8160 as described by the printed message.
Fixes: 65e87c0398 ("i40evf: support queue-specific settings for interrupt moderation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 3a2c6ced90 ("i40e: Add a check to see if MFS is set") added
a warning message that reports unexpected size of port's MFS (max
frame size) value. This message use for the port number local
variable 'i' that is wrong.
In i40e_probe() this 'i' variable is used only to iterate VSIs
to find FDIR VSI:
<code>
...
/* if FDIR VSI was set up, start it now */
for (i = 0; i < pf->num_alloc_vsi; i++) {
if (pf->vsi[i] && pf->vsi[i]->type == I40E_VSI_FDIR) {
i40e_vsi_open(pf->vsi[i]);
break;
}
}
...
</code>
So the warning message use for the port number index of FDIR VSI
if this exists or pf->num_alloc_vsi if not.
Fix the message by using 'pf->hw.port' for the port number.
Fixes: 3a2c6ced90 ("i40e: Add a check to see if MFS is set")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix setting dis_rx_filtering depending on whether port vlan is being
turned on or off. This was originally fixed in commit c793f8ea15 ("ice:
Fix disabling Rx VLAN filtering with port VLAN enabled"), but while
refactoring ice_vf_vsi_init_vlan_ops(), the fix has been lost. Restore the
fix along with the original comment from that change.
Also delete duplicate lines in ice_port_vlan_on().
Fixes: 2946204b3f ("ice: implement bridge port vlan")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
vfs::num_msix_per should be only used as default value for
vf->num_msix. For other use cases vf->num_msix should be used, as VF can
have different MSI-X amount values.
Fix incorrect register index calculation. vfs::num_msix_per and
pf->sriov_base_vector shouldn't be used after implementation of changing
MSI-X amount on VFs. Instead vf->first_vector_idx should be used, as it
is storing value for first irq index.
Fixes: fe1c5ca2fe ("ice: implement num_msix field per VF")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When code is applicable for both E822 and E823 devices, rename it from
E822 to E82X.
ICE_PHY_PER_NAC_E822 was unused, so just remove it.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The E822 hardware for Tx timestamping keeps track of how many
outstanding timestamps are still in the PHY memory block. It will not
generate a new interrupt to the MAC until all of the timestamps in the
region have been read.
If somehow all the available data is not read, but the driver has exited
its interrupt routine already, the PHY will not generate a new interrupt
even if new timestamp data is captured. Because no interrupt is
generated, the driver never processes the timestamp data. This state
results in a permanent failure for all future Tx timestamps.
It is not clear how the driver and hardware could enter this state.
However, if it does, there is currently no recovery mechanism.
Add a recovery mechanism via the periodic PTP work thread which invokes
ice_ptp_periodic_work(). Introduce a new check,
ice_ptp_maybe_trigger_tx_interrupt() which checks the PHY timestamp
ready bitmask. If any bits are set, trigger a software interrupt by
writing to PFINT_OICR.
Once triggered, the main timestamp processing thread will read through
the PHY data and clear the outstanding timestamp data. Once cleared, new
data should trigger interrupts as expected.
This should allow recovery from such a state rather than leaving the
device in a state where we cannot process Tx timestamps.
It is possible that this function checks for timestamp data
simultaneously with the interrupt, and it might trigger additional
unnecessary interrupts. This will cause a small amount of additional
processing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During reset, TX_TSYN interrupt should be processed as it may process
timestamps in brief moments before and after reset.
Timestamping should be enabled on VSIs at the end of reset procedure.
On ice_get_phy_tx_tstamp_ready error, interrupt should not be rearmed
because error only happens on resets.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Supported number of ntuple filters affect also maximum location value that
can be provided to ethtool command. Update error message to provide info
about max supported value.
Fix double spaces in the error messages.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If Clock Generation Unit is present on NIC board user shall know its
details.
Provide the devlink info callback with a new:
- fixed type object (cgu.id) indicating hardware variant of onboard CGU,
- running type object (fw.cgu) consisting of CGU id, config and firmware
versions.
These information shall be known for debugging purposes.
Test (on NIC board with CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu
cgu.id 36
fw.cgu 8032.16973825.6021
Test (on NIC board without CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu -c
0
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After the napi context is initialized, map the napi instance
with the queue/queue-set on the corresponding irq line.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Link: https://lore.kernel.org/r/170147332060.5260.13310934657151560599.stgit@anambiarhost.jf.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an error when an interface has the following conditions:
- PF is in an aggregate (bond)
- PF has VFs created on it
- bond is in a state where it is failed-over to the secondary interface
- A VF reset is issued on one or more of those VFs
The issue is generated by the originating PF trying to rebuild or
reconfigure the VF resources. Since the bond is failed over to the
secondary interface the queue contexts are in a modified state.
To fix this issue, have the originating interface reclaim its resources
prior to the tear-down and rebuild or reconfigure. Then after the process
is complete, move the resources back to the currently active interface.
There are multiple paths that can be used depending on what triggered the
event, so create a helper function to move the queues and use paired calls
to the helper (back to origin, process, then move back to active interface)
under the same lag_mutex lock.
Fixes: 1e0f9881ef ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20231127212340.1137657-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-11-27 (i40e, iavf)
This series contains updates to i40e and iavf drivers.
Ivan Vecera performs more cleanups on i40e and iavf drivers; removing
unused fields, defines, and unneeded fields.
Petr Oros utilizes iavf_schedule_aq_request() helper to replace open
coded equivalents.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
iavf: use iavf_schedule_aq_request() helper
iavf: Remove queue tracking fields from iavf_adminq_ring
i40e: Remove queue tracking fields from i40e_adminq_ring
i40e: Remove AQ register definitions for VF types
i40e: Delete unused and useless i40e_pf fields
====================
Link: https://lore.kernel.org/r/20231127211037.1135403-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the iavf_schedule_aq_request() helper when we need to
schedule a watchdog task immediately. No functional change.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fields 'head', 'tail', 'len', 'bah' and 'bal' in iavf_adminq_ring
are used to store register offsets. These offsets are initialized
and remains constant so there is no need to store them in the
iavf_adminq_ring structure.
Remove these fields from iavf_adminq_ring and use register offset
constants instead. Remove iavf_adminq_init_regs() that originally
stores these constants into these fields.
Finally improve iavf_check_asq_alive() that assumes that
non-zero value of hw->aq.asq.len indicates fully initialized
AdminQ send queue. Replace it by check for non-zero value
of field hw->aq.asq.count that is non-zero when the sending
queue is initialized and is zeroed during shutdown of
the queue.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fields 'head', 'tail', 'len', 'bah' and 'bal' in i40e_adminq_ring
are used to store register offsets. These offsets are initialized
and remains constant so there is no need to store them in the
i40e_adminq_ring structure.
Remove these fields from i40e_adminq_ring and use register offset
constants instead. Remove i40e_adminq_init_regs() that originally
stores these constants into these fields.
Finally improve i40e_check_asq_alive() that assumes that
non-zero value of hw->aq.asq.len indicates fully initialized
AdminQ send queue. Replace it by check for non-zero value
of field hw->aq.asq.count that is non-zero when the sending
queue is initialized and is zeroed during shutdown of
the queue.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The i40e driver does not handle its VF device types so there
is no need to keep AdminQ register definitions for such
device types. Remove them.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Removed fields:
.fc_autoneg_status
Since commit c56999f948 ("i40e/i40evf: Add set_fc and init of
FC settings") write-only and otherwise unused
.eeprom_version
Write-only and otherwise unused
.atr_sample_rate
Has only one possible value (I40E_DEFAULT_ATR_SAMPLE_RATE). Remove
it and replace its occurrences by I40E_DEFAULT_ATR_SAMPLE_RATE
.adminq_work_limit
Has only one possible value (I40E_AQ_WORK_LIMIT). Remove it and
replace its occurrences by I40E_AQ_WORK_LIMIT
.tx_sluggish_count
Unused, never written
.pf_seid
Used to store VSI downlink seid and it is referenced only once
in the same codepath. There is no need to save it into i40e_pf.
Remove it and use downlink_seid directly in the mentioned log
message.
.instance
Write only. Remove it as well as ugly static local variable
'pfs_found' in i40e_probe.
.int_policy
.switch_kobj
.ptp_pps_work
.ptp_extts1_work
.ptp_pps_start
.pps_delay
.ptp_pin
.override_q_count
All these unused at all
Prior the patch:
pahole -Ci40e_pf drivers/net/ethernet/intel/i40e/i40e.ko | tail -5
/* size: 5368, cachelines: 84, members: 127 */
/* sum members: 5297, holes: 20, sum holes: 71 */
/* paddings: 6, sum paddings: 19 */
/* last cacheline: 56 bytes */
};
After the patch:
pahole -Ci40e_pf drivers/net/ethernet/intel/i40e/i40e.ko | tail -5
/* size: 4976, cachelines: 78, members: 112 */
/* sum members: 4905, holes: 17, sum holes: 71 */
/* paddings: 6, sum paddings: 19 */
/* last cacheline: 48 bytes */
};
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.
This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.
This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.
Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.
Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:
1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()
2) ice_ptp_restore_timestamp_mode() which calls
ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
issues an immediate TSYN_TX interrupt to ensure that timestamps which
may have occurred during the device reset get processed.
Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.
This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.
With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.
Fixes: 77a781155a ("ice: enable receive hardware timestamping")
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit d938a8cca8 ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.
The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.
For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.
If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.
The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.
Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.
This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.
Fixes: d938a8cca8 ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.
Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.
In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.
Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.
A following change will fix the reset path to properly restore user
timestamping configuration completely.
This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
ice: one by one port representors creation
Michal Swiatkowski says:
Currently ice supports creating port representors only for VFs. For that
use case they can be created and removed in one step.
This patchset is refactoring current flow to support port representor
creation also for subfunctions and SIOV. In this case port representors
need to be created and removed one by one. Also, they can be added and
removed while other port representors are running.
To achieve that we need to change the switchdev configuration flow.
Three first patches are only cosmetic (renaming, removing not used code).
Next few ones are preparation for new flow. The most important one
is "add VF representor one by one". It fully implements new flow.
New type of port representor (for subfunction) will be introduced in
follow up patchset.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: reserve number of CP queues
ice: adjust switchdev rebuild path
ice: add VF representors one by one
ice: realloc VSI stats arrays
ice: set Tx topology every time new repr is added
ice: allow changing SWITCHDEV_CTRL VSI queues
ice: return pointer to representor
ice: make representor code generic
ice: remove VF pointer reference in eswitch code
ice: track port representors in xarray
ice: use repr instead of vf->repr
ice: track q_id in representor
ice: remove unused control VSI parameter
ice: remove redundant max_vsi_num variable
ice: rename switchdev to eswitch
====================
Link: https://lore.kernel.org/r/20231114181449.1290117-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
igc: Add support for physical + free-running timers
Vinicius Costa Gomes says:
The objective is to allow having functionality that depends on the
physical timer (taprio and ETF offloads, for example) and vclocks
operating together.
The "big" missing piece is the implementation of the .getcyclesx64()
function in igc, as i225/i226 have multiple timers, we use one of
those timers (timer 1) as a free-running (non adjustable) timer.
The complication is that only implementing .getcyclesx64() and nothing
else will break synchronization when using vclocks, as reading the clock
will retrieve the free-running value but timnestamps will come from the
adjustable timer. The solution is to modify "in one go" the timestamping
code to be able to retrieve the timestamp from the correct timer (if a
socket is "phc_bound" to a vclock the timestamp will come from the
free-running timer).
I was debating whether or not to do the adjustments for the internal latencies
for the free-running timestamps, decided to do the adjustments so the path
delay when using vclocks is similar to the one when using the physical clock.
One future improvement is to implement the .getcrosscycles() function.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igc: Add support for PTP .getcyclesx64()
igc: Simplify setting flags in the TX data descriptor
====================
Link: https://lore.kernel.org/r/20231114183640.1303163-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From commit 9eed69a914 ("i40e: Drop FCoE code from core driver files")
the field i40e_mac_info.san_addr is unused (never filled).
The field i40e_mac_info.max_fcoeq is unused from the beginning.
Remove both.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Co-developed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-16-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The i40e_hw.mac.type cannot to be equal to I40E_MAC_VF or
I40E_MAC_X722_VF so remove helper i40e_is_vf(), simplify
i40e_adminq_init_regs() and remove enums for these VF MAC types.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-14-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new helpers to check versions of running FW and provided
AQ API to make the code more readable.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-13-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add another helper functions that will be used by subsequent
patch to refactor existing open-coded checks whether the version
of running firmware and AdminQ API is recent enough to provide
certain capabilities.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-12-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move i40e_is_aq_api_ver_ge helper function (used to check if AdminQ
API version is recent enough) to header so it can be used from
other .c files.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-11-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some i40e_hw.caps bits are set in i40e_set_hw_caps(), some of them
in i40e_init_adminq() and the rest of them in i40e_sw_init().
Consolidate the initialization to single proper place i40e_set_hw_caps().
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-10-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fields .caps in i40e_hw and .hw_features in i40e_pf both indicate
capabilities provided by hardware. Move and merge i40e_pf.hw_features
into i40e_hw.caps as this is more appropriate place for them and
adjust their names to I40E_HW_CAP_... convention.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-9-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert flags field in i40e_hw from u64 to bitmap and its usage
to use bit access functions and rename the field to 'caps' as
this field describes capabilities that are set once on init and
read many times later.
Changes:
- Convert "hw_ptr->flags & FLAG" to "test_bit(FLAG, ...)"
- Convert "hw_ptr->flags |= FLAG" to "set_bit(FLAG, ...)"
- Convert "hw_ptr->flags &= ~FLAG" to "clear_bit(FLAG, ...)"
- Rename i40e_hw.flags to i40e_hw.caps
- Rename i40e_set_hw_flags() to i40e_set_hw_caps()
- Adjust caps names so they are prefixed by I40E_HW_CAP_ and existing
_CAPABLE suffixes are stripped
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-8-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert flags and hw_features fields from i40e_pf from u32 to
bitmaps and their usage to use bit access functions.
Changes:
- Convert "pf_ptr->(flags|hw_features) & FL" to "test_bit(FL, ...)"
- Convert "pf_ptr->(flags|hw_features) |= FL" to "set_bit(FL, ...)"
- Convert "pf_ptr->(flags|hw_features) &= ~FL" to "clear_bit(FL, ...)"
- Rename flag field to bitno in i40e_priv_flags and adjust ethtool
callbacks to work with flags bitmap
- Rename flag names where '_ENABLED'->'_ENA' and '_DISABLED'->'_DIS'
like in ice driver
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-7-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enum type names should not be suffixed by '_t'. Either to use
'typedef enum name name_t' to so plain 'name_t var' instead of
'enum name_t var'.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-6-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The flag I40E_FLAG_RX_CSUM_ENABLED and I40E_HW_FLAG_DROP_MODE are
set and never read. Remove them.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make the driver not produce an error message on
"ethtool -m ethX" command when a non-SFP module is encountered
hence there is no possibility to read the EEPROM.
Make the message to appear in the debug log rather
than as an error string.
Change the return code to -EOPNOTSUPP and the string to make
it more verbose.
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
CC: Stefan Assmann <sassmann@redhat.com>
CC: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
check the value of 'ret' after calling 'i40e_vsi_config_rss'.
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-3-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In Tables 8-12 and 8-22 in the X710/XXV710/XL710 datasheet, the QLEN
description states that the maximum size of the descriptor queue is 8k
minus 32, or 8160.
Signed-off-by: Justin Bronder <jsbronder@cold-front.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231113231047.548659-2-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for using Timer 1 (i225/i226 have 4 timer registers) as a
free-running clock (the "cycles" clock) in addition to Timer 0 (the
default, "adjustable clock"). The objective is to allow taprio/etf
offloading to coexist with PTP vclocks.
Besides the implementation of .getcyclesx64() for i225/i226, to keep
timestamping working when vclocks are in use, we also need to add
support for TX and RX timestamping using the free running timer, when
the requesting socket is bound to a vclock.
On the RX side, i225/i226 can be configured to store the values of two
timers in the received packet metadata area, so it's a matter of
configuring the right registers and retrieving the right timestamp.
The TX is a bit more involved because the hardware stores a single
timestamp (with the selected timer in the TX descriptor) into one of
the timestamp registers.
Note some changes at how the timestamps are done for RX, the
conversion and adjustment of timestamps are now done closer to the
consumption of the timestamp instead of near the reception.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We can re-use the IGC_SET_FLAG() macro to simplify setting some values
in the TX data descriptor. With the macro it's easier to get the
meaning of the operations.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rebuilding CP VSI each time the PR is created drastically increase the
time of maximum VFs creation. Add function to reserve number of CP
queues to deal with this problem.
Use the same function to decrease number of queues in case of removing
VFs. Assume that caller of ice_eswitch_reserve_cp_queues() will also
call ice_eswitch_attach/detach() correct number of times.
Still one by one PR adding is handy for VF resetting routine.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There is no need to use specific functions for rebuilding path. Let's
use current implementation by removing all representors and as the
result remove switchdev environment.
It will be added in devices rebuild path. For example during adding VFs,
port representors for them also will be created.
Rebuild control plane VSI before removing representors with INIT_VSI
flag set to reinit VSI in hardware after reset.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement adding representors one by one. Always set switchdev
environment when first representor is being added and clear environment
when last one is being removed.
Basic switchdev configuration remains the same. Code related to creating
and configuring representor was changed.
Instead of setting whole representors in one function handle only one
representor in setup function. The same with removing representors.
Stop representors when new one is being added or removed. Stop means,
disabling napi, stopping traffic and removing slow path rule. It is
needed because ::q_id will change after remapping, so each representor
will need new rule.
When representor are stopped rebuild control plane VSI with one more or
one less queue. One more if new representor is being added, one less if
representor is being removed.
Bridge port is removed during unregister_netdev() call on PR, so there
is no need to call it from driver side.
After that do remap new queues to correct vector. At the end start all
representors (napi enable, start queues, add slow path rule).
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously only case when queues amount is lower was covered. Implement
realloc for case when queues amount is higher than previous one. Use
krealloc() function and zero new allocated elements.
It has to be done before ice_vsi_def_cfg(), because stats element for
ring is set there.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is needed to track correct Tx topology. Update it every time new
representor is created or remove node in case of removing corresponding
representor.
Still clear all node when removing switchdev mode as part of Tx topology
isn't related only to representors. Also clear ::rate_note value to
prevent skipping this node next time Tx topology is created.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement mechanism to change number of queues for SWITCHDEV_CTRL VSI
type.
Value from ::req_txq/rxq will be written to ::alloc_txq/rxq after
calling ice_vsi_rebuild().
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In follow up patches it will be easier to obtain created port
representor pointer instead of the id. Without it the pattern from
eswitch side will look like:
- create PR
- get PR based on the id
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Representor code needs to be independent from specific device type, like
in this case VF. Make generic add / remove representor function and
specific add VF / rem VF function. New device types will follow this
scheme.
In bridge offload code there is a need to get representor pointer based
on VSI. Implement helper function to achieve that.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Make eswitch code generic by removing VF pointer reference in functions.
It is needed to support eswitch mode for other type of devices.
Previously queue id used for Rx was based on VF number. Use ::q_id saved
in port representor instead.
After adding or removing port representor ::q_id value can change. It
isn't good idea to iterate over representors list using this value.
Use xa_find starting from the first one instead to get next port
representor to remap.
The number of port representors has to be equal to ::num_rx/tx_q. Warn if
it isn't true.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of assuming that each VF has pointer to port representor save it
in xarray. It will allow adding port representor for other device types.
Drop reference to VF where it is use only to get port representor. Get
it from xarray instead.
The functions will no longer by specific for VF, rename them.
Track id assigned by xarray in port representor structure. The id can't
be used as ::q_id, because it is fixed during port representor lifetime.
::q_id can change after adding / removing other port representors.
Side effect of removing VF pointer is that we are losing VF MAC
information used in unrolling. Store it in port representor as parent
MAC.
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Extract repr from vf->repr as it is often use in the ice_repr_rem().
Remove meaningless clearing of q_vector and netdev pointers as kfree is
called on repr pointer.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously queue index of control plane VSI used by port representor was
always id of VF. If we want to allow adding port representors for
different devices we have to track queue index in the port representor
structure.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It isn't used in ice_eswitch_release_reprs(). Probably leftover. Remove
it.
Commit that has removed usage of ctrl_vsi:
commit c1e5da5dd4 ("ice: improve switchdev's slow-path")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is a leftover from previous implementation. Accidentally it wasn't
removed. Do it now.
Commit that has removed it:
commit c1e5da5dd4 ("ice: improve switchdev's slow-path")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Eswitch is used as a prefix for related functions. Main structure
storing all data related to eswitch should also be named as eswitch
instead of ice_switchdev_info. Rename it.
Also rename switchdev to eswitch where the context is not about eswitch
mode.
::uplink_netdev was changed to netdev for simplicity. There is no other
netdev in function scope so it is obvious.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 3cbdb03430 ("ice: Add support for E830 DDP package segment")
incorrectly removed support for package download for packages without a
signature segment. These packages include the signature buffer inline
in the configurations buffers, and not in a signature segment.
Fix package download by providing download support for both packages
with (ice_download_pkg_with_sig_seg()) and without signature segment
(ice_download_pkg_without_sig_seg()).
Fixes: 3cbdb03430 ("ice: Add support for E830 DDP package segment")
Reported-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Closes: https://lore.kernel.org/netdev/ZUT50a94kk2pMGKb@boxer/
Tested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The dpll output pins which are used to feed clock signal of PHY and MAC
circuits cannot be disconnected, those integrated circuits require clock
signal for operation.
By stopping assignment of DPLL_PIN_CAPABILITIES_STATE_CAN_CHANGE pin
capability, prevent the user from invoking the state set callback on
those pins, setting the state on those pins already returns error, as
firmware doesn't allow the change of their state.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Fixes: 8a3a565ff2 ("ice: add admin commands to access cgu configuration")
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Supported priority value for input pins may differ with regard of NIC
firmware version. E810T NICs with 3.20/4.00 FW versions would accept
priority range 0-31, where firmware 4.10+ would support the range 0-9
and extra value of 255.
Remove the in-range check as the driver has no information on supported
values from the running firmware, let firmware decide if given value is
correct and return extack error if the value is not supported.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When dpll device is registered and dpll subsystem performs notify of a
new device, the lock state value provided to dpll subsystem equals 0
which is invalid value for the `enum dpll_lock_status`.
Provide correct value by obtaining it from firmware before registering
the dpll device.
Fixes: d7999f5ea6 ("ice: implement dpll interface to control cgu")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-11-06 (ice)
This series contains updates to ice driver only.
Dave removes SR-IOV LAG attribute for only the interface being disabled
to allow for proper unwinding of all interfaces.
Michal Schmidt changes some LAG allocations from GFP_KERNEL to GFP_ATOMIC
due to non-allowed sleeping.
Aniruddha and Marcin fix redirection and drop rules for switchdev by
properly setting and marking egress/ingress type.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix VF-VF direction matching in drop rule in switchdev
ice: Fix VF-VF filter rules in switchdev mode
ice: lag: in RCU, use atomic allocation
ice: Fix SRIOV LAG disable on non-compliant aggregate
====================
Link: https://lore.kernel.org/r/20231107004844.655549-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-11-06 (i40e)
This series contains updates to i40e driver only.
Ivan Vecera resolves a couple issues with devlink; removing a call to
devlink_port_type_clear() and ensuring devlink port is unregistered
after the net device.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix devlink port unregistering
i40e: Do not call devlink_port_type_clear()
====================
Link: https://lore.kernel.org/r/20231107003600.653796-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When adding a drop rule on a VF, rule direction is not being set, which
results in it always being set to ingress (ICE_ESWITCH_FLTR_INGRESS
equals 0). Because of this, drop rules added on port representors don't
match any packets.
To fix it, set rule direction in drop action to egress when netdev is a
port representor, otherwise set it to ingress.
Fixes: 0960a27bd4 ("ice: Add direction metadata")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Any packet leaving VSI i.e VF's VSI is considered as
egress traffic by HW, thus failing to match the added
rule.
Mark the direction for redirect rules as below:
1. VF-VF - Egress
2. Uplink-VF - Ingress
3. VF-Uplink - Egress
4. Link_Partner-Uplink - Ingress
5. Link_Partner-VF - Ingress
Fixes: 0960a27bd4 ("ice: Add direction metadata")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Aniruddha Paul <aniruddha.paul@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sleeping is not allowed in RCU read-side critical sections.
Use atomic allocations under rcu_read_lock.
Fixes: 1e0f9881ef ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Fixes: 41ccedf5ca ("ice: implement lag netdev event handler")
Fixes: 3579aa86fb ("ice: update reset path for SRIOV LAG support")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If an attribute of an aggregate interface disqualifies it from supporting
SRIOV, the driver will unwind the SRIOV support. Currently the driver is
clearing the feature bit for all interfaces in the aggregate, but this is
not allowing the other interfaces to unwind successfully on driver unload.
Only clear the feature bit for the interface that is currently unwinding.
Fixes: bf65da2eb2 ("ice: enforce interface eligibility and add messaging for SRIOV LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Do not call devlink_port_type_clear() prior devlink port unregister
and let devlink core to take care about it.
Reproducer:
[root@host ~]# rmmod i40e
[ 4539.964699] i40e 0000:02:00.0: devlink port type for port 0 cleared without a software interface reference, device type not supported by the kernel?
[ 4540.319811] i40e 0000:02:00.1: devlink port type for port 1 cleared without a software interface reference, device type not supported by the kernel?
Fixes: 9e479d64dc ("i40e: Add initial devlink support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The iavf client interface was added in 2017 by commit ed0e894de7
("i40evf: add client interface"), but there have never been any in-tree
callers.
It's not useful for future development either. The Intel out-of-tree
iavf and irdma drivers instead use an auxiliary bus, which is a better
solution.
Remove the iavf client interface code. Also gone are the client_task
work and the client_lock mutex.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-9-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a new function iavf_free_interrupt_scheme that does the inverse of
iavf_init_interrupt_scheme. Symmetry is nice. And there will be three
callers already.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-8-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use unregister_netdev, which takes rtnl_lock for us. We don't have to
check the reg_state under rtnl_lock. There's nothing to race with. We
have just cancelled the finish_config work.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-7-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The information whether a netdev has been registered is already present
in the netdev itself. There's no need for a driver flag with the same
meaning.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-6-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Every time I create VFs on ice, I receive at least one "Device is still
in reset (-16), retrying" message per VF. It recovers fine, but typical
usecases should not trigger scary-looking messages.
The waiting for reset is too short. It makes no sense to check every 10
microseconds. Typical reset waiting times are at least tens of
milliseconds and can be several seconds. I suspect the polling interval
was meant to be 10 milliseconds all along.
IAVF_RESET_WAIT_COMPLETE_COUNT is defined as 2000, so the total waiting
time could be over 20 seconds. I have seen resets take 5 seconds (with
128 VFs on ice).
The added benefit of not triggering the "Device is still in reset" path
is that we avoid going through the __IAVF_INIT_FAILED state, which would
take a full second before retrying.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-5-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reason for queueing watchdog_task is to have it process the
aq_required flags that are being set here. If comms failed, there's
nothing to do, so return early.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-4-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This pattern appears in two places in the iavf source code:
while (!mutex_trylock(...))
usleep_range(...);
That's just mutex_lock with extra steps.
The pattern is a leftover from when iavf used bit flags instead of
mutexes for locking. Commit 5ac49f3c27 ("iavf: use mutexes for locking
of critical sections") replaced test_and_set_bit with !mutex_trylock,
preserving the pattern.
Simplify it to mutex_lock.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bit lock __IAVF_IN_CRITICAL_TASK does not exist anymore since commit
5ac49f3c27 ("iavf: use mutexes for locking of critical sections").
Adjust the comments accordingly.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231027175941.1340255-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As the previous patches provide support for E830 hardware, add E830
specific IDs to the PCI device ID table, so these devices can now be
probed by the kernel.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-7-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove zeroing of the fields, as all the fields are in fact initialized
with zeros automatically
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-6-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for E830 DDP package segment. For the E830 package,
signature buffers will not be included inline in the configuration
buffers. Instead, the signature buffers will be located in a
signature segment.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-5-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Get Link Status data length can vary with different versions of
ice_aqc_get_link_status_data. Add ice_get_link_status_datalen() to return
datalen for the specific ice_aqc_get_link_status_data version.
Add new link partner fields to ice_aqc_get_link_status_data; PHY type,
FEC, and flow control.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-4-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the support for 200G phy speeds and the mapping for their
advertisement in link. Add the new PHY type bits for AQ command, as
needed for 200G E830 controllers.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
E830 is the 200G NIC family which uses the ice driver.
Add specific E830 registers. Embed macros to use proper register based on
(hw)->mac_type & name those macros to [ORIGINAL]_BY_MAC(hw). Registers
only available on one of the macs will need to be explicitly referred to
as E800_NAME instead of just NAME. PTP is not yet supported.
Co-developed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Milena Olech <milena.olech@intel.com>
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Co-developed-by: Scott Taylor <scott.w.taylor@intel.com>
Signed-off-by: Scott Taylor <scott.w.taylor@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In iavf_down, we're skipping the scheduling of certain operations if
the driver is being removed. However, the IAVF_FLAG_AQ_DISABLE_QUEUES
request must not be skipped in this case, because iavf_close waits
for the transition to the __IAVF_DOWN state, which happens in
iavf_virtchnl_completion after the queues are released.
Without this fix, "rmmod iavf" takes half a second per interface that's
up and prints the "Device resources not yet released" warning.
Fixes: c8de44b577 ("iavf: do not process adminq tasks when __IAVF_IN_REMOVE_TASK is set")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025183213.874283-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The I40E_TXR_FLAGS_WB_ON_ITR is i40e_ring flag and not i40e_pf one.
Fixes: 8e0764b4d6 ("i40e/i40evf: Add support for writeback on ITR feature for X722")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231023212714.178032-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PP_FLAG_PAGE_FRAG is not really needed after pp_frag_count
handling is unified and page_pool_alloc_frag() is supported
in 32-bit arch with 64-bit DMA, so remove it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
CC: Lorenzo Bianconi <lorenzo@kernel.org>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: Liang Chen <liangchen.linux@gmail.com>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Link: https://lore.kernel.org/r/20231020095952.11055-3-linyunsheng@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In idpf_vc_core_init, the mailbox work is queued
on a mailbox workqueue but it is not cancelled on error.
This results in a call trace when idpf_mbx_task tries
to access the freed mailbox queue pointer. Fix it by
cancelling the mailbox work in the error path.
Fixes: 4930fbf419 ("idpf: add core init and interrupt request")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231023202655.173369-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The HW must be programmed differently for queue-based scheduling mode.
To program the completion queue context correctly, the control plane
must know the scheduling mode not only for the Tx queue, but also for
the completion queue.
Unfortunately, currently the driver sets the scheduling mode only for
the Tx queues.
Propagate the scheduling mode data for the completion queue as
well when sending the queue configuration messages.
Fixes: 1c325aac10 ("idpf: configure resources for TX queues")
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231023202655.173369-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a programming status desc is encountered on the rx_ring,
next_to_process is bumped along with cleaned_count but next_to_clean is
not. This causes I40E_DESC_UNUSED() macro to misbehave resulting in
overwriting whole ring with new buffers.
Update next_to_clean to point to next_to_process on seeing a programming
status desc if not in the middle of handling a multi-frag packet. Also,
bump cleaned_count only for such case as otherwise next_to_clean buffer
may be returned to hardware on reaching clean_threshold.
Fixes: e9031f2da1 ("i40e: introduce next_to_process to i40e_ring")
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reported-by: hq.dev+kernel@msdfc.xyz
Reported by: Solomon Peachy <pizza@shaftnet.org>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217678
Tested-by: hq.dev+kernel@msdfc.xyz
Tested by: Indrek Järve <incx@dustbite.net>
Signed-off-by: Tirthendu Sarkar <tirthendu.sarkar@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231019203852.3663665-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'ethtool_convert_link_mode_to_legacy_u32' method does not allow us to
advertise 2500M speed support and TP (twisted pair) properly. Convert to
'ethtool_link_ksettings_test_link_mode' to advertise supported speed and
eliminate ambiguity.
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Suggested-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231019203641.3661960-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add check for return of igb_update_ethtool_nfc_entry so that in case
of any potential errors the memory alocated for input will be freed.
Fixes: 0e71def252 ("igb: add support of RX network flow classification")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list iterator in a list_for_each_entry() loop can never be NULL.
If the loop exits without hitting a break then the iterator points
to an offset off the list head and dereferencing it is an out of
bounds access.
Before we transitioned to using list_for_each_entry() loops, then
it was possible for "entry" to be NULL and the comments mention
this. I have updated the comments to match the new code.
Fixes: c1fec89045 ("ethernet/intel: Use list_for_each_entry() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we exit a list_for_each_entry() without hitting a break statement,
the list iterator isn't NULL, it just point to an offset off the
list_head. In that situation, it wouldn't be too surprising for
entry->free to be true and we end up corrupting memory.
The way to test for these is to just set a flag.
Fixes: c1fec89045 ("ethernet/intel: Use list_for_each_entry() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ice_find_netlist_node function was introduced in commit 8a3a565ff2
("ice: add admin commands to access cgu configuration"). Variations of this
function were reviewed concurrently on both intel-wired-lan[1][2], and
netdev [3][4]
[1]: https://lore.kernel.org/intel-wired-lan/20230913204943.1051233-7-vadim.fedorenko@linux.dev/
[2]: https://lore.kernel.org/intel-wired-lan/20230817000058.2433236-5-jacob.e.keller@intel.com/
[3]: https://lore.kernel.org/netdev/20230918212814.435688-1-anthony.l.nguyen@intel.com/
[4]: https://lore.kernel.org/netdev/20230913204943.1051233-7-vadim.fedorenko@linux.dev/
The variant I posted had a few changes due to review feedback which were
never incorporated into the DPLL series:
* Replace the references to ancient and long removed ICE_SUCCESS and
ICE_ERR_DOES_NOT_EXIST status codes in the function comment.
* Return -ENOENT instead of -ENOTBLK, as a more common way to indicate that
an entry doesn't exist.
* Avoid the use of memset() and use simple static initialization for the
cmd variable.
* Use FIELD_PREP to assign the node_type_ctx.
* Remove an unnecessary local variable to keep track of rec_node_handle,
just pass the node_handle pointer directly into ice_aq_get_netlist_node.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ice_get_pf_c827_idx function is only called inside of ice_ptp_hw.c, so
there is no reason to export it. Mark it static and remove the declaration
from ice_ptp_hw.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: David S. Miller <davem@davemloft.net>
Track MSI-X for VFs using bitmap, by setting and clearing bitmap during
allocation and freeing.
Try to linearize irqs usage for VFs, by freeing them and allocating once
again. Do it only for VFs that aren't currently running.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera
Jakub Kicinski
Kurt Kanzenbach
Dave Ertman
Sasha Neftin
Kunwu Chan
David S. Miller
Maciej Fijalkowski
Wojciech Drewek
Grzegorz Nitka
Jesse Brandeburg
Jedrzej Jagielski
Paul M Stillwell Jr
Aniruddha Paul
Pavan Kumar Linga
Jiri Pirko
Heiner Kallweit
Jacob Keller
Christophe JAILLET
Tirthendu Sarkar
Michal Schmidt
Tony Nguyen
Rodrigo Cataldo
Paul Greenwalt
Andrii Staikov
Ke Xiao
Simon Horman
Ovidiu Panait
Jan Glaza
Jan Sokolowski
Karol Kolacinski
Sudheer Mogilappagari
Arkadiusz Kubalewski
Ngai-Mint Kwan
Katarzyna Wieczerzycka
Alexander Lobakin
Paolo Abeni
Larysa Zaremba
Jason Xing
Ahmed Zaki
Jeff Guo
Qi Zhang
Michal Kubiak
Ilpo Järvinen
Slawomir Laba
Piotr Gardocki
justinstitt@google.com
Marcin Szycik
Michal Swiatkowski
Pawel Kaminski
Konrad Knitter
Amritha Nambiar
Dan Carpenter
Petr Oros
Su Hui
Justin Bronder
Vinicius Costa Gomes
Dan Nowlin
Eric Dumazet
Pawel Chmielewski
Alice Michael
Yunsheng Lin
Mateusz Palczewski