Track the range being invalidated by mmu_notifier and skip page fault
retries if the fault address is not affected by the in-progress
invalidation. Handle concurrent invalidations by finding the minimal
range which includes all ranges being invalidated. Although the combined
range may include unrelated addresses and cannot be shrunk as individual
invalidation operations complete, it is unlikely the marginal gains of
proper range tracking are worth the additional complexity.
The primary benefit of this change is the reduction in the likelihood of
extreme latency when handing a page fault due to another thread having
been preempted while modifying host virtual addresses.
Signed-off-by: David Stevens <stevensd@chromium.org>
Message-Id: <20210222024522.1751719-3-stevensd@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't retry a page fault due to an mmu_notifier invalidation when
handling a page fault for a GPA that did not resolve to a memslot, i.e.
an MMIO page fault. Invalidations from the mmu_notifier signal a change
in a host virtual address (HVA) mapping; without a memslot, there is no
HVA and thus no possibility that the invalidation is relevant to the
page fault being handled.
Note, the MMIO vs. memslot generation checks handle the case where a
pending memslot will create a memslot overlapping the faulting GPA. The
mmu_notifier checks are orthogonal to memslot updates.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210222024522.1751719-2-stevensd@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove several exports from the MMU that are no longer necessary.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-15-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop kvm_mmu_slot_largepage_remove_write_access() and refactor its sole
caller to use kvm_mmu_slot_remove_write_access(). Remove the now-unused
slot_handle_large_level() and slot_handle_all_level() helpers.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-14-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stop setting dirty bits for MMU pages when dirty logging is disabled for
a memslot, as PML is now completely disabled when there are no memslots
with dirty logging enabled.
This means that spurious PML entries will be created for memslots with
dirty logging disabled if at least one other memslot has dirty logging
enabled. However, spurious PML entries are already possible since
dirty bits are set only when a dirty logging is turned off, i.e. memslots
that are never dirty logged will have dirty bits cleared.
In the end, it's faster overall to eat a few spurious PML entries in the
window where dirty logging is being disabled across all memslots.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-13-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the facade of KVM's PML logic being vendor specific and move the
bits that aren't truly VMX specific into common x86 code. The MMU logic
for dealing with PML is tightly coupled to the feature and to VMX's
implementation, bouncing through kvm_x86_ops obfuscates the code without
providing any meaningful separation of concerns or encapsulation.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the vendor-specific dirty log size in a variable, there's no need
to wrap it in a function since the value is constant after
hardware_setup() runs.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-9-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When zapping SPTEs in order to rebuild them as huge pages, use the new
helper that computes the max mapping level to detect whether or not a
SPTE should be zapped. Doing so avoids zapping SPTEs that can't
possibly be rebuilt as huge pages, e.g. due to hardware constraints,
memslot alignment, etc...
This also avoids zapping SPTEs that are still large, e.g. if migration
was canceled before write-protected huge pages were shattered to enable
dirty logging. Note, such pages are still write-protected at this time,
i.e. a page fault VM-Exit will still occur. This will hopefully be
addressed in a future patch.
Sadly, TDP MMU loses its const on the memslot, but that's a pervasive
problem that's been around for quite some time.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-6-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass the memslot to the rmap callbacks, it will be used when zapping
collapsible SPTEs to verify the memslot is compatible with hugepages
before zapping its SPTEs.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Factor out the logic for determining the maximum mapping level given a
memslot and a gpa. The helper will be used when zapping collapsible
SPTEs when disabling dirty logging, e.g. to avoid zapping SPTEs that
can't possibly be rebuilt as hugepages.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210213005015.1651772-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When retpolines are enabled they have high overhead in the inner loop
inside kvm_handle_hva_range() that iterates over the provided memory area.
Let's mark this function and its TDP MMU equivalent __always_inline so
compiler will be able to change the call to the actual handler function
inside each of them into a direct one.
This significantly improves performance on the unmap test on the existing
kernel memslot code (tested on a Xeon 8167M machine):
30 slots in use:
Test Before After Improvement
Unmap 0.0353s 0.0334s 5%
Unmap 2M 0.00104s 0.000407s 61%
509 slots in use:
Test Before After Improvement
Unmap 0.0742s 0.0740s None
Unmap 2M 0.00221s 0.00159s 28%
Looks like having an indirect call in these functions (and, so, a
retpoline) might have interfered with unrolling of the whole loop in the
CPU.
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <732d3fe9eb68aa08402a638ab0309199fa89ae56.1612810129.git.maciej.szmigiero@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The TDP MMU assumes that it can do atomic accesses to 64-bit PTEs.
Rather than just disabling it, compile it out completely so that it
is possible to use for example 64-bit xchg.
To limit the number of stubs, wrap all accesses to tdp_mmu_enabled
or tdp_mmu_page with a function. Calls to all other functions in
tdp_mmu.c are eliminated and do not even reach the linker.
Reviewed-by: Sean Christopherson <seanjc@google.com>
Tested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a helper to generate the mask of reserved PA bits in the host.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210204000117.3303214-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use reserved_gpa_bits, which accounts for exceptions to the maxphyaddr
rule, e.g. SEV's C-bit, for the page {table,directory,etc...} entry (PxE)
reserved bits checks. For SEV, the C-bit is ignored by hardware when
walking pages tables, e.g. the APM states:
Note that while the guest may choose to set the C-bit explicitly on
instruction pages and page table addresses, the value of this bit is a
don't-care in such situations as hardware always performs these as
private accesses.
Such behavior is expected to hold true for other features that repurpose
GPA bits, e.g. KVM could theoretically emulate SME or MKTME, which both
allow non-zero repurposed bits in the page tables. Conceptually, KVM
should apply reserved GPA checks universally, and any features that do
not adhere to the basic rule should be explicitly handled, i.e. if a GPA
bit is repurposed but not allowed in page tables for whatever reason.
Refactor __reset_rsvds_bits_mask() to take the pre-generated reserved
bits mask, and opportunistically clean up its code, e.g. to align lines
and comments.
Practically speaking, this is change is a likely a glorified nop given
the current KVM code base. SEV's C-bit is the only repurposed GPA bit,
and KVM doesn't support shadowing encrypted page tables (which is
theoretically possible via SEV debug APIs).
Cc: Rick Edgecombe <rick.p.edgecombe@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210204000117.3303214-9-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make the last few changes necessary to enable the TDP MMU to handle page
faults in parallel while holding the mmu_lock in read mode.
Reviewed-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210202185734.1680553-24-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a read / write lock to be used in place of the MMU spinlock on x86.
The rwlock will enable the TDP MMU to handle page faults, and other
operations in parallel in future commits.
Reviewed-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210202185734.1680553-19-bgardon@google.com>
[Introduce virt/kvm/mmu_lock.h - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Given the common pattern:
rmap_printk("%s:"..., __func__,...)
we could improve this by adding '__func__' in rmap_printk().
Signed-off-by: Stephen Zhang <stephenzhangzsd@gmail.com>
Message-Id: <1611713325-3591-1-git-send-email-stephenzhangzsd@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert kvm_x86_ops to use static calls. Note that all kvm_x86_ops are
covered here except for 'pmu_ops and 'nested ops'.
Here are some numbers running cpuid in a loop of 1 million calls averaged
over 5 runs, measured in the vm (lower is better).
Intel Xeon 3000MHz:
|default |mitigations=off
-------------------------------------
vanilla |.671s |.486s
static call|.573s(-15%)|.458s(-6%)
AMD EPYC 2500MHz:
|default |mitigations=off
-------------------------------------
vanilla |.710s |.609s
static call|.664s(-6%) |.609s(0%)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Message-Id: <e057bf1b8a7ad15652df6eeba3f907ae758d3399.1610680941.git.jbaron@akamai.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove the update_pte() shadow paging logic, which was obsoleted by
commit 4731d4c7a0 ("KVM: MMU: out of sync shadow core"), but never
removed. As pointed out by Yu, KVM never write protects leaf page
tables for the purposes of shadow paging, and instead marks their
associated shadow page as unsync so that the guest can write PTEs at
will.
The update_pte() path, which predates the unsync logic, optimizes COW
scenarios by refreshing leaf SPTEs when they are written, as opposed to
zapping the SPTE, restarting the guest, and installing the new SPTE on
the subsequent fault. Since KVM no longer write-protects leaf page
tables, update_pte() is unreachable and can be dropped.
Reported-by: Yu Zhang <yu.c.zhang@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210115004051.4099250-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Walk the list of MMU pages in reverse in kvm_mmu_zap_oldest_mmu_pages().
The list is FIFO, meaning new pages are inserted at the head and thus
the oldest pages are at the tail. Using a "forward" iterator causes KVM
to zap MMU pages that were just added, which obliterates guest
performance once the max number of shadow MMU pages is reached.
Fixes: 6b82ef2c9c ("KVM: x86/mmu: Batch zap MMU pages when recycling oldest pages")
Reported-by: Zdenek Kaspar <zkaspar82@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210113205030.3481307-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check only the terminal leaf for a "!PRESENT || MMIO" SPTE when looking
for reserved bits on valid, non-MMIO SPTEs. The get_walk() helpers
terminate their walks if a not-present or MMIO SPTE is encountered, i.e.
the non-terminal SPTEs have already been verified to be regular SPTEs.
This eliminates an extra check-and-branch in a relatively hot loop.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-5-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Bump the size of the sptes array by one and use the raw level of the
SPTE to index into the sptes array. Using the SPTE level directly
improves readability by eliminating the need to reason out why the level
is being adjusted when indexing the array. The array is on the stack
and is not explicitly initialized; bumping its size is nothing more than
a superficial adjustment to the stack frame.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-4-seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Get the so called "root" level from the low level shadow page table
walkers instead of manually attempting to calculate it higher up the
stack, e.g. in get_mmio_spte(). When KVM is using PAE shadow paging,
the starting level of the walk, from the callers perspective, is not
the CR3 root but rather the PDPTR "root". Checking for reserved bits
from the CR3 root causes get_mmio_spte() to consume uninitialized stack
data due to indexing into sptes[] for a level that was not filled by
get_walk(). This can result in false positives and/or negatives
depending on what garbage happens to be on the stack.
Opportunistically nuke a few extra newlines.
Fixes: 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Reported-by: Richard Herbert <rherbert@sympatico.ca>
Cc: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return -1 from the get_walk() helpers if the shadow walk doesn't fill at
least one spte, which can theoretically happen if the walk hits a
not-present PDPTR. Returning the root level in such a case will cause
get_mmio_spte() to return garbage (uninitialized stack data). In
practice, such a scenario should be impossible as KVM shouldn't get a
reserved-bit page fault with a not-present PDPTR.
Note, using mmu->root_level in get_walk() is wrong for other reasons,
too, but that's now a moot point.
Fixes: 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Cc: Ben Gardon <bgardon@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20201218003139.2167891-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU") caused
the following WARNING on an Intel Ice Lake CPU:
get_mmio_spte: detect reserved bits on spte, addr 0xb80a0, dump hierarchy:
------ spte 0xb80a0 level 5.
------ spte 0xfcd210107 level 4.
------ spte 0x1004c40107 level 3.
------ spte 0x1004c41107 level 2.
------ spte 0x1db00000000b83b6 level 1.
WARNING: CPU: 109 PID: 10254 at arch/x86/kvm/mmu/mmu.c:3569 kvm_mmu_page_fault.cold.150+0x54/0x22f [kvm]
...
Call Trace:
? kvm_io_bus_get_first_dev+0x55/0x110 [kvm]
vcpu_enter_guest+0xaa1/0x16a0 [kvm]
? vmx_get_cs_db_l_bits+0x17/0x30 [kvm_intel]
? skip_emulated_instruction+0xaa/0x150 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xca/0x520 [kvm]
The guest triggering this crashes. Note, this happens with the traditional
MMU and EPT enabled, not with the newly introduced TDP MMU. Turns out,
there was a subtle change in the above mentioned commit. Previously,
walk_shadow_page_get_mmio_spte() was setting 'root' to 'iterator.level'
which is returned by shadow_walk_init() and this equals to
'vcpu->arch.mmu->shadow_root_level'. Now, get_mmio_spte() sets it to
'int root = vcpu->arch.mmu->root_level'.
The difference between 'root_level' and 'shadow_root_level' on CPUs
supporting 5-level page tables is that in some case we don't want to
use 5-level, in particular when 'cpuid_maxphyaddr(vcpu) <= 48'
kvm_mmu_get_tdp_level() returns '4'. In case upper layer is not used,
the corresponding SPTE will fail '__is_rsvd_bits_set()' check.
Revert to using 'shadow_root_level'.
Fixes: 95fb5b0258 ("kvm: x86/mmu: Support MMIO in the TDP MMU")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20201126110206.2118959-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because kvm dirty rings and kvm dirty log is used in an exclusive way,
Let's avoid creating the dirty_bitmap when kvm dirty ring is enabled.
At the meantime, since the dirty_bitmap will be conditionally created
now, we can't use it as a sign of "whether this memory slot enabled
dirty tracking". Change users like that to check against the kvm
memory slot flags.
Note that there still can be chances where the kvm memory slot got its
dirty_bitmap allocated, _if_ the memory slots are created before
enabling of the dirty rings and at the same time with the dirty
tracking capability enabled, they'll still with the dirty_bitmap.
However it should not hurt much (e.g., the bitmaps will always be
freed if they are there), and the real users normally won't trigger
this because dirty bit tracking flag should in most cases only be
applied to kvm slots only before migration starts, that should be far
latter than kvm initializes (VM starts).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012226.5868-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch is heavily based on previous work from Lei Cao
<lei.cao@stratus.com> and Paolo Bonzini <pbonzini@redhat.com>. [1]
KVM currently uses large bitmaps to track dirty memory. These bitmaps
are copied to userspace when userspace queries KVM for its dirty page
information. The use of bitmaps is mostly sufficient for live
migration, as large parts of memory are be dirtied from one log-dirty
pass to another. However, in a checkpointing system, the number of
dirty pages is small and in fact it is often bounded---the VM is
paused when it has dirtied a pre-defined number of pages. Traversing a
large, sparsely populated bitmap to find set bits is time-consuming,
as is copying the bitmap to user-space.
A similar issue will be there for live migration when the guest memory
is huge while the page dirty procedure is trivial. In that case for
each dirty sync we need to pull the whole dirty bitmap to userspace
and analyse every bit even if it's mostly zeros.
The preferred data structure for above scenarios is a dense list of
guest frame numbers (GFN). This patch series stores the dirty list in
kernel memory that can be memory mapped into userspace to allow speedy
harvesting.
This patch enables dirty ring for X86 only. However it should be
easily extended to other archs as well.
[1] https://patchwork.kernel.org/patch/10471409/
Signed-off-by: Lei Cao <lei.cao@stratus.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012222.5767-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix an off-by-one style bug in pte_list_add() where it failed to
account the last full set of SPTEs, i.e. when desc->sptes is full
and desc->more is NULL.
Merge the two "PTE_LIST_EXT-1" checks as part of the fix to avoid
an extra comparison.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <1601196297-24104-1-git-send-email-lirongqing@baidu.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Even though the compiler is able to replace static const variables with
their value, it will warn about them being unused when Linux is built with W=1.
Use good old macros instead, this is not C++.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When KVM maps a largepage backed region at a lower level in order to
make it executable (i.e. NX large page shattering), it reduces the TLB
performance of that region. In order to avoid making this degradation
permanent, KVM must periodically reclaim shattered NX largepages by
zapping them and allowing them to be rebuilt in the page fault handler.
With this patch, the TDP MMU does not respect KVM's rate limiting on
reclaim. It traverses the entire TDP structure every time. This will be
addressed in a future patch.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-21-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Direct roots don't have a write flooding count because the guest can't
affect that paging structure. Thus there's no need to clear the write
flooding count on a fast CR3 switch for direct roots.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-20-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to support MMIO, KVM must be able to walk the TDP paging
structures to find mappings for a given GFN. Support this walk for
the TDP MMU.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
v2: Thanks to Dan Carpenter and kernel test robot for finding that root
was used uninitialized in get_mmio_spte.
Signed-off-by: Ben Gardon <bgardon@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20201014182700.2888246-19-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To support nested virtualization, KVM will sometimes need to write
protect pages which are part of a shadowed paging structure or are not
writable in the shadowed paging structure. Add a function to write
protect GFN mappings for this purpose.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-18-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dirty logging ultimately breaks down MMU mappings to 4k granularity.
When dirty logging is no longer needed, these granaular mappings
represent a useless performance penalty. When dirty logging is disabled,
search the paging structure for mappings that could be re-constituted
into a large page mapping. Zap those mappings so that they can be
faulted in again at a higher mapping level.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-17-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dirty logging is a key feature of the KVM MMU and must be supported by
the TDP MMU. Add support for both the write protection and PML dirty
logging modes.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-16-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to interoperate correctly with the rest of KVM and other Linux
subsystems, the TDP MMU must correctly handle various MMU notifiers. Add
a hook and handle the change_pte MMU notifier.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-15-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to interoperate correctly with the rest of KVM and other Linux
subsystems, the TDP MMU must correctly handle various MMU notifiers. The
main Linux MM uses the access tracking MMU notifiers for swap and other
features. Add hooks to handle the test/flush HVA (range) family of
MMU notifiers.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-14-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to interoperate correctly with the rest of KVM and other Linux
subsystems, the TDP MMU must correctly handle various MMU notifiers. Add
hooks to handle the invalidate range family of MMU notifiers.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-13-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add functions to handle page faults in the TDP MMU. These page faults
are currently handled in much the same way as the x86 shadow paging
based MMU, however the ordering of some operations is slightly
different. Future patches will add eager NX splitting, a fast page fault
handler, and parallel page faults.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-11-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to avoid creating executable hugepages in the TDP MMU PF
handler, remove the dependency between disallowed_hugepage_adjust and
the shadow_walk_iterator. This will open the function up to being used
by the TDP MMU PF handler in a future patch.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-10-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add functions to zap SPTEs to the TDP MMU. These are needed to tear down
TDP MMU roots properly and implement other MMU functions which require
tearing down mappings. Future patches will add functions to populate the
page tables, but as for this patch there will not be any work for these
functions to do.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-8-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The existing bookkeeping done by KVM when a PTE is changed is spread
around several functions. This makes it difficult to remember all the
stats, bitmaps, and other subsystems that need to be updated whenever a
PTE is modified. When a non-leaf PTE is marked non-present or becomes a
leaf PTE, page table memory must also be freed. To simplify the MMU and
facilitate the use of atomic operations on SPTEs in future patches, create
functions to handle some of the bookkeeping required as a result of
a change.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The TDP MMU must be able to allocate paging structure root pages and track
the usage of those pages. Implement a similar, but separate system for root
page allocation to that of the x86 shadow paging implementation. When
future patches add synchronization model changes to allow for parallel
page faults, these pages will need to be handled differently from the
x86 shadow paging based MMU's root pages.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The TDP MMU offers an alternative mode of operation to the x86 shadow
paging based MMU, optimized for running an L1 guest with TDP. The TDP MMU
will require new fields that need to be initialized and torn down. Add
hooks into the existing KVM MMU initialization process to do that
initialization / cleanup. Currently the initialization and cleanup
fucntions do not do very much, however more operations will be added in
future patches.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-4-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SPTE format will be common to both the shadow and the TDP MMU.
Extract code that implements the format to a separate module, as a
first step towards adding the TDP MMU and putting mmu.c on a diet.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The TDP MMU's own function for the changed-PTE notifier will need to be
update a PTE in the exact same way as the shadow MMU. Rather than
re-implementing this logic, factor the SPTE creation out of kvm_set_pte_rmapp.
Extracted out of a patch by Ben Gardon. <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Separate the functions for generating leaf page table entries from the
function that inserts them into the paging structure. This refactoring
will facilitate changes to the MMU sychronization model to use atomic
compare / exchanges (which are not guaranteed to succeed) instead of a
monolithic MMU lock.
No functional change expected.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This commit introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The TDP MMU page fault handler will need to be able to create non-leaf
SPTEs to build up the paging structures. Rather than re-implementing the
function, factor the SPTE creation out of link_shadow_page.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20200925212302.3979661-9-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These should be const, so make it so.
Signed-off-by: Joe Perches <joe@perches.com>
Message-Id: <ed95eef4f10fc1317b66936c05bc7dd8f943a6d5.1601770305.git.joe@perches.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move initialization of 'struct kvm_mmu' fields into alloc_mmu_pages() to
consolidate code, and rename the helper to __kvm_mmu_create().
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923163314.8181-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use bools to track write and user faults throughout the page fault paths
and down into mmu_set_spte(). The actual usage is purely boolean, but
that's not obvious without digging into all paths as the current code
uses a mix of bools (TDP and try_async_pf) and ints (shadow paging and
mmu_set_spte()).
No true functional change intended (although the pgprintk() will now
print 0/1 instead of 0/PFERR_WRITE_MASK).
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-9-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the "ITLB multi-hit workaround enabled" check into the callers of
disallowed_hugepage_adjust() to make it more obvious that the helper is
specific to the workaround, and to be consistent with the accounting,
i.e. account_huge_nx_page() is called if and only if the workaround is
enabled.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-8-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Condition the accounting of a disallowed huge NX page on the original
requested level of the page being greater than the current iterator
level. This does two things: accounts the page if and only if a huge
page was actually disallowed, and accounts the shadow page if and only
if it was the level at which the huge page was disallowed. For the
latter case, the previous logic would account all shadow pages used to
create the translation for the forced small page, e.g. even PML4, which
can't be a huge page on current hardware, would be accounted as having
been a disallowed huge page when using 5-level EPT.
The overzealous accounting is purely a performance issue, i.e. the
recovery thread will spuriously zap shadow pages, but otherwise the bad
behavior is harmless.
Cc: Junaid Shahid <junaids@google.com>
Fixes: b8e8c8303f ("kvm: mmu: ITLB_MULTIHIT mitigation")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-6-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Apply the "huge page disallowed" adjustment of the max level only after
capturing the original requested level. The requested level will be
used in a future patch to skip adding pages to the list of disallowed
huge pages if a huge page wasn't possible anyways, e.g. if the page
isn't mapped as a huge page in the host.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-5-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calculate huge_page_disallowed in __direct_map() and FNAME(fetch) in
preparation for reworking the calculation so that it preserves the
requested map level and eventually to avoid flagging a shadow page as
being disallowed for being used as a large/huge page when it couldn't
have been huge in the first place, e.g. because the backing page in the
host is not large.
Pass the error code into the helpers and use it to recalcuate exec and
write_fault instead adding yet more booleans to the parameters.
Opportunistically use huge_page_disallowed instead of lpage_disallowed
to match the nomenclature used within the mapping helpers (though even
they have existing inconsistencies).
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-4-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Refactor the zap loop in kvm_recover_nx_lpages() to be a for loop that
iterates on to_zap and drop the !to_zap check that leads to the in-loop
calling of kvm_mmu_commit_zap_page(). The in-loop commit when to_zap
hits zero is superfluous now that there's an unconditional commit after
the loop to handle the case where lpage_disallowed_mmu_pages is emptied.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-3-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call kvm_mmu_commit_zap_page() after exiting the "prepare zap" loop in
kvm_recover_nx_lpages() to finish zapping pages in the unlikely event
that the loop exited due to lpage_disallowed_mmu_pages being empty.
Because the recovery thread drops mmu_lock() when rescheduling, it's
possible that lpage_disallowed_mmu_pages could be emptied by a different
thread without to_zap reaching zero despite to_zap being derived from
the number of disallowed lpages.
Fixes: 1aa9b9572b ("kvm: x86: mmu: Recovery of shattered NX large pages")
Cc: Junaid Shahid <junaids@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923183735.584-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Detect spurious page faults, e.g. page faults that occur when multiple
vCPUs simultaneously access a not-present page, and skip the SPTE write,
prefetch, and stats update for spurious faults.
Note, the performance benefits of skipping the write and prefetch are
likely negligible, and the false positive stats adjustment is probably
lost in the noise. The primary motivation is to play nice with TDX's
SEPT in the long term. SEAMCALLs (to program SEPT entries) are quite
costly, e.g. thousands of cycles, and a spurious SEPT update will result
in a SEAMCALL error (which KVM will ideally treat as fatal).
Reported-by: Kai Huang <kai.huang@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923220425.18402-5-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Introduce RET_PF_FIXED and RET_PF_SPURIOUS to provide unique return
values instead of overloading RET_PF_RETRY. In the short term, the
unique values add clarity to the code and RET_PF_SPURIOUS will be used
by set_spte() to avoid unnecessary work for spurious faults.
In the long term, TDX will use RET_PF_FIXED to deterministically map
memory during pre-boot. The page fault flow may bail early for benign
reasons, e.g. if the mmu_notifier fires for an unrelated address. With
only RET_PF_RETRY, it's impossible for the caller to distinguish between
"cool, page is mapped" and "darn, need to try again", and thus cannot
handle benign cases like the mmu_notifier retry.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923220425.18402-4-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Explicitly check for RET_PF_EMULATE instead of implicitly doing the same
by checking for !RET_PF_RETRY (RET_PF_INVALID is handled earlier). This
will adding new RET_PF_ types in future patches without breaking the
emulation path.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923220425.18402-3-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Exit to userspace with an error if the MMU is buggy and returns
RET_PF_INVALID when servicing a page fault. This will allow a future
patch to invert the emulation path, i.e. emulate only on RET_PF_EMULATE
instead of emulating on anything but RET_PF_RETRY. This technically
means that KVM will exit to userspace instead of emulating on
RET_PF_INVALID, but practically speaking it's a nop as the MMU never
returns RET_PF_INVALID.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923220425.18402-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Recursively zap all to-be-orphaned children, unsynced or otherwise, when
zapping a shadow page for a nested TDP MMU. KVM currently only zaps the
unsynced child pages, but not the synced ones. This can create problems
over time when running many nested guests because it leaves unlinked
pages which will not be freed until the page quota is hit. With the
default page quota of 20 shadow pages per 1000 guest pages, this looks
like a memory leak and can degrade MMU performance.
In a recent benchmark, substantial performance degradation was observed:
An L1 guest was booted with 64G memory.
2G nested Windows guests were booted, 10 at a time for 20
iterations. (200 total boots)
Windows was used in this benchmark because they touch all of their
memory on startup.
By the end of the benchmark, the nested guests were taking ~10% longer
to boot. With this patch there is no degradation in boot time.
Without this patch the benchmark ends with hundreds of thousands of
stale EPT02 pages cluttering up rmaps and the page hash map. As a
result, VM shutdown is also much slower: deleting memslot 0 was
observed to take over a minute. With this patch it takes just a
few miliseconds.
Cc: Peter Shier <pshier@google.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Co-developed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923221406.16297-3-sean.j.christopherson@intel.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the logic that controls whether or not FNAME(invlpg) needs to flush
fully into FNAME(invlpg) so that mmu_page_zap_pte() doesn't return a
value. This allows a future patch to redefine the return semantics for
mmu_page_zap_pte() so that it can recursively zap orphaned child shadow
pages for nested TDP MMUs.
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923221406.16297-2-sean.j.christopherson@intel.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
To make kvm_mmu_free_roots() a bit more readable, capture 'kvm' in a
local variable instead of doing vcpu->kvm over and over (and over).
No functional change intended.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200923191204.8410-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename kvm_mmu_is_illegal_gpa() to kvm_vcpu_is_illegal_gpa() and move it
to cpuid.h so that's it's colocated with cpuid_maxphyaddr(). The helper
is not MMU specific and will gain a user that is completely unrelated to
the MMU in a future patch.
No functional change intended.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200924194250.19137-5-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Replace the existing kvm_x86_ops.need_emulation_on_page_fault() with a
more generic is_emulatable(), and unconditionally call the new function
in x86_emulate_instruction().
KVM will use the generic hook to support multiple security related
technologies that prevent emulation in one way or another. Similar to
the existing AMD #NPF case where emulation of the current instruction is
not possible due to lack of information, AMD's SEV-ES and Intel's SGX
and TDX will introduce scenarios where emulation is impossible due to
the guest's register state being inaccessible. And again similar to the
existing #NPF case, emulation can be initiated by kvm_mmu_page_fault(),
i.e. outside of the control of vendor-specific code.
While the cause and architecturally visible behavior of the various
cases are different, e.g. SGX will inject a #UD, AMD #NPF is a clean
resume or complete shutdown, and SEV-ES and TDX "return" an error, the
impact on the common emulation code is identical: KVM must stop
emulation immediately and resume the guest.
Query is_emulatable() in handle_ud() as well so that the
force_emulation_prefix code doesn't incorrectly modify RIP before
calling emulate_instruction() in the absurdly unlikely scenario that
KVM encounters forced emulation in conjunction with "do not emulate".
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200915232702.15945-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When kvm_mmu_get_page() gets a page with unsynced children, the spt
pagetable is unsynchronized with the guest pagetable. But the
guest might not issue a "flush" operation on it when the pagetable
entry is changed from zero or other cases. The hypervisor has the
responsibility to synchronize the pagetables.
KVM behaved as above for many years, But commit 8c8560b833
("KVM: x86/mmu: Use KVM_REQ_TLB_FLUSH_CURRENT for MMU specific flushes")
inadvertently included a line of code to change it without giving any
reason in the changelog. It is clear that the commit's intention was to
change KVM_REQ_TLB_FLUSH -> KVM_REQ_TLB_FLUSH_CURRENT, so we don't
needlessly flush other contexts; however, one of the hunks changed
a nearby KVM_REQ_MMU_SYNC instead. This patch changes it back.
Link: https://lore.kernel.org/lkml/20200320212833.3507-26-sean.j.christopherson@intel.com/
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20200902135421.31158-1-jiangshanlai@gmail.com>
fixes: 8c8560b833 ("KVM: x86/mmu: Use KVM_REQ_TLB_FLUSH_CURRENT for MMU specific flushes")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the
case of kvm_mmu_notifier_invalidate_range_start(), this field is not
forwarded on to the architecture-specific implementation of
kvm_unmap_hva_range() and therefore the backend cannot sensibly decide
whether or not to block.
Add an extra 'flags' parameter to kvm_unmap_hva_range() so that
architectures are aware as to whether or not they are permitted to block.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-2-will@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
x86:
* Report last CPU for debugging
* Emulate smaller MAXPHYADDR in the guest than in the host
* .noinstr and tracing fixes from Thomas
* nested SVM page table switching optimization and fixes
Generic:
* Unify shadow MMU cache data structures across architectures
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl8pC+oUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNcOwgAjomqtEqQNlp7DdZT7VyyklzbxX1/
ud7v+oOJ8K4sFlf64lSthjPo3N9rzZCcw+yOXmuyuITngXOGc3tzIwXpCzpLtuQ1
WO1Ql3B/2dCi3lP5OMmsO1UAZqy9pKLg1dfeYUPk48P5+p7d/NPmk+Em5kIYzKm5
JsaHfCp2EEXomwmljNJ8PQ1vTjIQSSzlgYUBZxmCkaaX7zbEUMtxAQCStHmt8B84
33LczwXBm3viSWrzsoBV37I70+tseugiSGsCfUyupXOvq55d6D9FCqtCb45Hn4Vh
Ik8ggKdalsk/reiGEwNw1/3nr6mRMkHSbl+Mhc4waOIFf9dn0urgQgOaDg==
=YVx0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"s390:
- implement diag318
x86:
- Report last CPU for debugging
- Emulate smaller MAXPHYADDR in the guest than in the host
- .noinstr and tracing fixes from Thomas
- nested SVM page table switching optimization and fixes
Generic:
- Unify shadow MMU cache data structures across architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
KVM: SVM: Fix sev_pin_memory() error handling
KVM: LAPIC: Set the TDCR settable bits
KVM: x86: Specify max TDP level via kvm_configure_mmu()
KVM: x86/mmu: Rename max_page_level to max_huge_page_level
KVM: x86: Dynamically calculate TDP level from max level and MAXPHYADDR
KVM: VXM: Remove temporary WARN on expected vs. actual EPTP level mismatch
KVM: x86: Pull the PGD's level from the MMU instead of recalculating it
KVM: VMX: Make vmx_load_mmu_pgd() static
KVM: x86/mmu: Add separate helper for shadow NPT root page role calc
KVM: VMX: Drop a duplicate declaration of construct_eptp()
KVM: nSVM: Correctly set the shadow NPT root level in its MMU role
KVM: Using macros instead of magic values
MIPS: KVM: Fix build error caused by 'kvm_run' cleanup
KVM: nSVM: remove nonsensical EXITINFO1 adjustment on nested NPF
KVM: x86: Add a capability for GUEST_MAXPHYADDR < HOST_MAXPHYADDR support
KVM: VMX: optimize #PF injection when MAXPHYADDR does not match
KVM: VMX: Add guest physical address check in EPT violation and misconfig
KVM: VMX: introduce vmx_need_pf_intercept
KVM: x86: update exception bitmap on CPUID changes
KVM: x86: rename update_bp_intercept to update_exception_bitmap
...
Capture the max TDP level during kvm_configure_mmu() instead of using a
kvm_x86_ops hook to do it at every vCPU creation.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200716034122.5998-10-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename max_page_level to explicitly call out that it tracks the max huge
page level so as to avoid confusion when a future patch moves the max
TDP level, i.e. max root level, into the MMU and kvm_configure_mmu().
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200716034122.5998-9-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calculate the desired TDP level on the fly using the max TDP level and
MAXPHYADDR instead of doing the same when CPUID is updated. This avoids
the hidden dependency on cpuid_maxphyaddr() in vmx_get_tdp_level() and
also standardizes the "use 5-level paging iff MAXPHYADDR > 48" behavior
across x86.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200716034122.5998-8-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Refactor the shadow NPT role calculation into a separate helper to
better differentiate it from the non-nested shadow MMU, e.g. the NPT
variant is never direct and derives its root level from the TDP level.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200716034122.5998-3-sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the initialization of shadow NPT MMU's shadow_root_level into
kvm_init_shadow_npt_mmu() and explicitly set the level in the shadow NPT
MMU's role to be the TDP level. This ensures the role and MMU levels
are synchronized and also initialized before __kvm_mmu_new_pgd(), which
consumes the level when attempting a fast PGD switch.
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 9fa72119b2 ("kvm: x86: Introduce kvm_mmu_calc_root_page_role()")
Fixes: a506fdd223 ("KVM: nSVM: implement nested_svm_load_cr3() and use it for host->guest switch")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200716034122.5998-2-sean.j.christopherson@intel.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Intel processors of various generations have supported 36, 39, 46 or 52
bits for physical addresses. Until IceLake introduced MAXPHYADDR==52,
running on a machine with higher MAXPHYADDR than the guest more or less
worked, because software that relied on reserved address bits (like KVM)
generally used bit 51 as a marker and therefore the page faults where
generated anyway.
Unfortunately this is not true anymore if the host MAXPHYADDR is 52,
and this can cause problems when migrating from a MAXPHYADDR<52
machine to one with MAXPHYADDR==52. Typically, the latter are machines
that support 5-level page tables, so they can be identified easily from
the LA57 CPUID bit.
When that happens, the guest might have a physical address with reserved
bits set, but the host won't see that and trap it. Hence, we need
to check page faults' physical addresses against the guest's maximum
physical memory and if it's exceeded, we need to add the PFERR_RSVD_MASK
bits to the page fault error code.
This patch does this for the MMU's page walks. The next patches will
ensure that the correct exception and error code is produced whenever
no host-reserved bits are set in page table entries.
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200710154811.418214-4-mgamal@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Also no point of it being inline since it's always called through
function pointers. So remove that.
Signed-off-by: Mohammed Gamal <mgamal@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200710154811.418214-3-mgamal@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The mmu_check_root() check in fast_pgd_switch() seems to be
superfluous: when GPA is outside of the visible range
cached_root_available() will fail for non-direct roots
(as we can't have a matching one on the list) and we don't
seem to care for direct ones.
Also, raising #TF immediately when a non-existent GFN is written to CR3
doesn't seem to mach architectural behavior. Drop the check.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200710141157.1640173-10-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Undesired triple fault gets injected to L1 guest on SVM when L2 is
launched with certain CR3 values. #TF is raised by mmu_check_root()
check in fast_pgd_switch() and the root cause is that when
kvm_set_cr3() is called from nested_prepare_vmcb_save() with NPT
enabled CR3 points to a nGPA so we can't check it with
kvm_is_visible_gfn().
Using generic kvm_set_cr3() when switching to nested guest is not
a great idea as we'll have to distinguish between 'real' CR3s and
'nested' CR3s to e.g. not call kvm_mmu_new_pgd() with nGPA. Following
nVMX implement nested-specific nested_svm_load_cr3() doing the job.
To support the change, nested_svm_load_cr3() needs to be re-ordered
with nested_svm_init_mmu_context().
Note: the current implementation is sub-optimal as we always do TLB
flush/MMU sync but this is still an improvement as we at least stop doing
kvm_mmu_reset_context().
Fixes: 7c390d350f ("kvm: x86: Add fast CR3 switch code path")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200710141157.1640173-8-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_init_shadow_mmu() was actually the only function that could be called
with different vcpu->arch.mmu values. Now that kvm_init_shadow_npt_mmu()
is separated from kvm_init_shadow_mmu(), we always know the MMU context
we need to use and there is no need to dereference vcpu->arch.mmu pointer.
Based on a patch by Vitaly Kuznetsov <vkuznets@redhat.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200710141157.1640173-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As a preparatory change for moving kvm_mmu_new_pgd() from
nested_prepare_vmcb_save() to nested_svm_init_mmu_context() split
kvm_init_shadow_npt_mmu() from kvm_init_shadow_mmu(). This also makes
the code look more like nVMX (kvm_init_shadow_ept_mmu()).
No functional change intended.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200710141157.1640173-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move x86's memory cache helpers to common KVM code so that they can be
reused by arm64 and MIPS in future patches.
Suggested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-16-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename the memory helpers that will soon be moved to common code and be
made globaly available via linux/kvm_host.h. "mmu" alone is not a
sufficient namespace for globally available KVM symbols.
Opportunistically add "nr_" in mmu_memory_cache_free_objects() to make
it clear the function returns the number of free objects, as opposed to
freeing existing objects.
Suggested-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-14-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't bother filling the gfn array cache when the caller is a fully
direct MMU, i.e. won't need a gfn array for shadow pages.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-13-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set __GFP_ZERO for the shadow page memory cache and drop the explicit
clear_page() from kvm_mmu_get_page(). This moves the cost of zeroing a
page to the allocation time of the physical page, i.e. when topping up
the memory caches, and thus avoids having to zero out an entire page
while holding mmu_lock.
Cc: Peter Feiner <pfeiner@google.com>
Cc: Peter Shier <pshier@google.com>
Cc: Junaid Shahid <junaids@google.com>
Cc: Jim Mattson <jmattson@google.com>
Suggested-by: Ben Gardon <bgardon@google.com>
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-12-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a gfp_zero flag to 'struct kvm_mmu_memory_cache' and use it to
control __GFP_ZERO instead of hardcoding a call to kmem_cache_zalloc().
A future patch needs such a flag for the __get_free_page() path, as
gfn arrays do not need/want the allocator to zero the memory. Convert
the kmem_cache paths to __GFP_ZERO now so as to avoid a weird and
inconsistent API in the future.
No functional change intended.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-11-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use separate caches for allocating shadow pages versus gfn arrays. This
sets the stage for specifying __GFP_ZERO when allocating shadow pages
without incurring extra cost for gfn arrays.
No functional change intended.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-10-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up the minimums in mmu_topup_memory_caches() to document the
driving mechanisms behind the minimums. Now that encountering an empty
cache is unlikely to trigger BUG_ON(), it is less dangerous to be more
precise when defining the minimums.
For rmaps, the logic is 1 parent PTE per level, plus a single rmap, and
prefetched rmaps. The extra objects in the current '8 + PREFETCH'
minimum came about due to an abundance of paranoia in commit
c41ef344de ("KVM: MMU: increase per-vcpu rmap cache alloc size"),
i.e. it could have increased the minimum to 2 rmaps. Furthermore, the
unexpected extra rmap case was killed off entirely by commits
f759e2b4c7 ("KVM: MMU: avoid pte_list_desc running out in
kvm_mmu_pte_write") and f5a1e9f895 ("KVM: MMU: remove call to
kvm_mmu_pte_write from walk_addr").
For the so called page cache, replace '8' with 2*PT64_ROOT_MAX_LEVEL.
The 2x multiplier is needed because the cache is used for both shadow
pages and gfn arrays for indirect MMUs.
And finally, for page headers, replace '4' with PT64_ROOT_MAX_LEVEL.
Note, KVM now supports 5-level paging, i.e. the old minimums that used a
baseline derived from 4-level paging were technically wrong. But, KVM
always allocates roots in a separate flow, e.g. it's impossible in the
current implementation to actually need 5 new shadow pages in a single
flow. Use PT64_ROOT_MAX_LEVEL unmodified instead of subtracting 1, as
the direct usage is likely more intuitive to uninformed readers, and the
inflated minimum is unlikely to affect functionality in practice.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-9-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Avoid refilling the memory caches and potentially slow reclaim/swap when
handling a fast page fault, which does not need to allocate any new
objects.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-7-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Attempt to allocate a new object instead of crashing KVM (and likely the
kernel) if a memory cache is unexpectedly empty. Use GFP_ATOMIC for the
allocation as the caches are used while holding mmu_lock. The immediate
BUG_ON() makes the code unnecessarily explosive and led to confusing
minimums being used in the past, e.g. allocating 4 objects where 1 would
suffice.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-6-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Return errors directly from mmu_topup_memory_caches() instead of
branching to a label that does the same.
No functional change intended.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-5-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use "mc" for local variables to shorten line lengths and provide
consistent names, which will be especially helpful when some of the
helpers are moved to common KVM code in future patches.
No functional change intended.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-4-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the "page" variants of the topup/free memory cache helpers, using
the existence of an associated kmem_cache to select the correct alloc
or free routine.
No functional change intended.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-3-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Track the kmem_cache used for non-page KVM MMU memory caches instead of
passing in the associated kmem_cache when filling the cache. This will
allow consolidating code and other cleanups.
No functional change intended.
Reviewed-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200703023545.8771-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
OVMF booted guest running on shadow pages crashes on TRIPLE FAULT after
enabling paging from SMM. The crash is triggered from mmu_check_root() and
is caused by kvm_is_visible_gfn() searching through memslots with as_id = 0
while vCPU may be in a different context (address space).
Introduce kvm_vcpu_is_visible_gfn() and use it from mmu_check_root().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200708140023.1476020-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
David Stevens
Sean Christopherson
Maciej S. Szmigiero
Paolo Bonzini
Ben Gardon
Stephen Zhang
Jason Baron
Vitaly Kuznetsov
Peter Xu
Li RongQing
Joe Perches
Sean Christopherson
Lai Jiangshan
Gustavo A. R. Silva
Will Deacon
Linus Torvalds
Kees Cook
Mohammed Gamal