Since iwl_fw_error_collect() is now always called with the sync
argument set to true, to collect data synchronously, remove the
argument from it entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.08f515513e88.I780a557743ca7f029f46a1cc75d0799542e39d83@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to later add the ability to do deeper resets of the
device when it crashes, first restructure the firmware error
handling. Instead of having just a single nic_error() method
that handles all, split it:
- nic_error() just handles and prints the error itself,
- dump_error() synchronously creates an error dump, and
- sw_reset() will be called to request doing a SW reset.
This changes the architecture so that the transport is now
responsible for deciding how to do the reset, and therefore
the handling of reprobe if error occurs during reconfig
moves there, which necessitates adding a method there that
notifies the transport that the recovery was completed.
Actually introducing the model under which deeper resets can
be done will be in future patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.6d4f741ae907.I96a9243e7877808ed6d1bff6967c15d6c24882f0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When some channel context manipulations fail, the device
is going to be restarted to try to recover. Make this go
through a real FW restart via an NMI so the transport is
aware of it and can later handle escalation, and to make
it easier to restructure the code later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.96b732029d20.I2e729f402db58a76cea620b6f62a02da49a10b48@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Except for some special handling in DVM, error dump and some
message behaviour, cmd_queue_full and nic_error are equivalent
now. Unify by giving a special error type, so DVM can continue
to differentiate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.0222183504aa.Ie29cef75fbd91b64a43619bc36bd5b29c5b9f957@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Approximately three years ago, in commit ddb6b76b6f
("iwlwifi: yoyo: support TLV-based firmware reset"), the code
was (likely erroneously) changed to no longer treat error
interrupts as firmware errors. As a result, this meant that
the fw_restart counter was only applied in case of command
queue being stuck, which never seems to happen. Also, there's
no longer any way to set the mvm->fw_restart to a value that
doesn't match exactly the module parameter behaviour.
Instead of trying to fix this, simply remove the logic that
limits the number of restarts, it's clearly unused.
However, restore the logic that restart isn't unconditional,
by checking the module parameter.
Since the "fw_error" argument to iwl_mvm_nic_restart() is now
always true (except in the "never happens" case of CMD queue
stuck), just remove it too and treat command queue stuck the
same way as everything else.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.b0489daf323c.I0cd3233b2214c5f06e059f746041b19d08647e40@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that the retry loop only happens when timeouts occur
and firmware errors are different, we no longer need the
STARTING state with all the infrastructure for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.c55d73436521.I08e9f6a71d56f86872bca4d4e3048faa113a7120@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to restrict the retry loops for timeouts, first
pass the error code up using ERR_PTR(). This of course
requires all existing functions to be updated accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.3fe5031d5784.I7307996c91dac69619ff9c616b8a077423fac19f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain platforms, it may necessary to use the STEP in URM
(ultra reliable mode.) Read the necessary flags from the BIOS
(ACPI or UEFI) and indicate the chosen mode to the firmware in
the context info. Whether or not URM really was configured is
already read back later, to adjust capabilities accordingly.
Signed-off-by: Somashekhar(Som) <somashekhar.puttagangaiah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.b30024905de3.If3c578af2c15f8005bbe71499bc4091348ed7bb0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of differentiating only sync/async, differentiate
the type of error, and document that only reset handshake
timeout (IWL_ERR_TYPE_RESET_HS_TIMEOUT) needs sync handling.
The special sync handling is somewhat temporary, the idea
is to later split the nic_error() method into error dump,
synchronizing the dump, and SW reset methods, and the type
is mostly in order to unify command queue full handling
into that new architecture as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.aed9c9e4fac0.I2288042bec4728a75b61cb7f6ded5214bfa3ce85@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace the ifdef CONFIG_PM by CONFIG_PM_SLEEP. CONFIG_PM was useful
when we had CONFIG_PM_RUNTIME but that was removed long ago.
Use PM_SLEEP consistently across the driver.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.44e47ba584de.I64f985d0405345252b76b7157291b79677abd64d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mwifiex has recently started to see active development which is good
news. rtw89 is also under active development and got several new
features. Otherwise not really anything out of ordinary.
We have one conflict in ath12k but that's easy to fix:
https://lore.kernel.org/all/20240808104348.6846e064@canb.auug.org.au/
Major changes:
mwifiex
* support for up to ten Authentication and Key Management (AKM) suites
* host MAC Sublayer Management Entity (MLME) client and AP mode support
* WPA-PSK-SHA256 AKM suite support
rtw88
* improve USB performance by aggregation
rtw89
* Wi-Fi 6 chip RTL8852BE-VT support
* WoWLAN net-detect support
* hardware encryption in unicast management frames support
* hardware rfkill support
ath12k
* DebugFS support for transmit DE stats
* Make ASPM support hardware-dependent
iwlwifi
* channel puncturing for US/CAN from UEFI
* bump FW API to 93 for BZ/SC devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmbYfCARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt+Qwf/X9oQ4sf8jV6eOV7EhoWhIHnQadvo5YBZ
ulBm8In0QGjEOVWkI7kXGabKP5jhne2lVIyP1eFfP2/td/A2yDWIuEeBfDQD6f4K
aiUGAa1gs4ZtGKJBniw/ukflSqJlR99N2qBO5T/smDm3Nw/aC522SO7BoLTpoJDQ
SuW4atFHMShXYf/vIrAA2yB9ok2yw/QM+27M9qjj6D7zzqsQxDl9wKGW+2v8KiSa
rXXbfnwfaQP21CYv5xYbEPACSRSV5Dr0TNopivWYxmm9svjLzwFN2JM2fHPxBEDh
wP6Ojp+Z32c1VbQtclLrwIQdlZ5yhU5MEDlVg5VLym9F83hv+oXTbA==
=lgVx
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
pull-request: wireless-next-2024-09-04
here's a pull request to net-next tree, more info below. Please let me know if
there are any problems.
====================
Conflicts:
drivers/net/wireless/ath/ath12k/hw.c
38055789d1 ("wifi: ath12k: use 128 bytes aligned iova in transmit path for WCN7850")
8be12629b4 ("wifi: ath12k: restore ASPM for supported hardwares only")
https://lore.kernel.org/87msldyj97.fsf@kernel.org
Link: https://patch.msgid.link/20240904153205.64C11C4CEC2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We used to have the opmode configuring it to the trans according to the
debug tlv value (FW_DBG_TRIGGER_TXQ_TIMERS).
But this debug is not used, so trans can just have the default value
hardcoded.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.87af3f063025.I2222981ead13f6a917f2d4b116c5b94200dc9e51@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the same handler for both types and just convert the old version to
the new. Drop the unused fields from the old one and fake the new
fields.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.a64ffc998569.I7d181052b1a69c331d07263f20c1e00cbc0bc891@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A new version is coming up. Rename the current struct to include the
current version.
s/iwl_missed_beacons_notif/iwl_missed_beacons_notif_v4
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.b5c3a83a05ef.I698611582b5ca8395f42a535c51f7230307e2c6f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the driver handles SMPS decisions by tracking AP
capabilities, BT coexistence changes, sending necessary SMPS
frames to the AP, and updating firmware with RX chain info
using the RLC_CONFIG_CMD.
Starting with version 3 of the RLC_CONFIG_CMD, the firmware
takes over this responsibility. It now tracks SMPS, sends
frames, and configures the RLC.
In this patch:
1. Stop sending RLC_CONFIG_CMD when firmware supports RLC
offload (version 3), as rlc.rx_chain_info is not needed by
firmware, and no other field in the cmd is used.
2. Prevent the driver from forwarding any SMPS requests to
mac80211, i.e., the driver should not transmit SMPS frames
to the AP as firmware handles that.
3. Set NL80211_FEATURE_DYNAMIC_SMPS and NL80211_FEATURE_STATIC_SMPS
conditionally based on RLC version.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45da23be1f65.I0d46db82dd990a82e8a66876fe2f5310bc9513be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a new notification the BT profile. It contains almost nothing,
only the wifi loss information. Copy this into mvm. We still need to
iterate over the vifs / links to use this data.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.637499f3a85a.I8bf654cf5d8aa038100273876c936845ecc338f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwl_bt_coex_profile_notif is now being obsoleted. It'll be replaced
by a new notification coming with a non-legacy group. Rename it to avoid
confusion.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.dc29fd0d7817.I5881fce86ec8b76ae98d2948265434b8e7d860c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Not doing so will make us send a host command to the transport while the
firmware is not alive, which will trigger a WARNING.
bad state = 0
WARNING: CPU: 2 PID: 17434 at drivers/net/wireless/intel/iwlwifi/iwl-trans.c:115 iwl_trans_send_cmd+0x1cb/0x1e0 [iwlwifi]
RIP: 0010:iwl_trans_send_cmd+0x1cb/0x1e0 [iwlwifi]
Call Trace:
<TASK>
iwl_mvm_send_cmd+0x40/0xc0 [iwlmvm]
iwl_mvm_config_scan+0x198/0x260 [iwlmvm]
iwl_mvm_recalc_tcm+0x730/0x11d0 [iwlmvm]
iwl_mvm_tcm_work+0x1d/0x30 [iwlmvm]
process_one_work+0x29e/0x640
worker_thread+0x2df/0x690
? rescuer_thread+0x540/0x540
kthread+0x192/0x1e0
? set_kthread_struct+0x90/0x90
ret_from_fork+0x22/0x30
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.5abe71ca1b6b.I97a968cb8be1f24f94652d9b110ecbf6af73f89e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_select_links is called by the link selection worker and it
requires the mutex.
Take it in the link selection worker.
This logic used to run from iwl_mvm_rx_umac_scan_complete_notif which
had the mvm->mutex held. This was changed to run in a worker holding the
wiphy mutex, but we also need the mvm->mutex.
Fixes: 2e194efa38 ("wifi: iwlwifi: mvm: Fix race in scan completion")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.0cacecd5db1e.Iaca38a078592b69bdd06549daf63408ccf1810e4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fast resume is a feature that was recently introduced to speed up the
resume time. It basically keeps the firmware alive while the system
is suspended and that avoids starting again the whole device.
This flow can't work for hibernation, since when the system boots,
before the frozen image is loaded, the kernel may touch the device. As a
result, we can't assume the device is in the exact same state as before
the hibernation.
Detect that we are resuming from hibernation through the PCI device and
forbid the fast resume flow. We also need to shut down the device
cleanly when that happens.
In addition, in case the device is power gated during S3, we won't be
able to keep the device alive. Detect this situation with BE200 at least
with the help of the CSR_FUNC_SCRATCH register and reset the device upon
resume if it was power gated during S3.
Fixes: e8bb19c1d5 ("wifi: iwlwifi: support fast resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.24eb3b19e74f.I3837810318dbef0a0a773cf4c4fcf89cdc6fdbd3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_mvm_get_bss_vif might return a NULL or ERR_PTR. Some of the callers
check only the NULL case, and some doesn't check at all.
Some of the callers even have a pointer to the mvmvif of the bss vif,
so we don't even need to call this function, and can simply get the vif
from mvmvif. Do it for those cases, and for the others - properly check
if IS_ERR_OR_NULL
Fixes: ec0d43d26f ("wifi: iwlwifi: mvm: Activate EMLSR based on traffic volume")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240703064027.a661f8c65aac.I45cf09b01af8ee3d55828863958ead741ea43b7f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we now want to sync the queues even when we're in RFKILL, we
shouldn't wake up the wait queue since we still expect to get all the
notifications from the firmware.
Fixes: 4d08c0b335 ("wifi: iwlwifi: mvm: handle BA session teardown in RF-kill")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240703064027.be7a9dbeacde.I5586cb3ca8d6e44f79d819a48a0c22351ff720c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PLDR (product level device reset) is a Windows term, and
is something the driver triggers there, AFAICT.
Really what 'pldr_sync' here wants to capture is whether
or not the firmware will/may do a product reset during
initialization, which makes the device drop off the bus,
requiring a rescan. If this is the case, obviously the
init will fail/time out, so we don't want to report all
kinds of errors etc., hence this tracking variable.
Rename it to 'fw_product_reset' to capture the meaning
better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240618194245.ccf849642af8.I01dded6b2393771b7baf8b4b17336784d987c7c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the first step towards removing the P2P Device MAC.
Use ROC (which uses the AUX MAC) for P2P Device
discoveribility and action frames.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140556.8c90e457abbd.I8e340759ecb299e05b1809f3d8060429c6cbbd01@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code that is parsing the amsdu_size module parameter and mapping it
to the corresponding Rx buffer size is common to all opmodes.
Move it into a function in iwlwifi, as preparation to a new op mode we
are working on.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240527190228.a3430d32923d.Iab3c22ef0df685f72f22dafc47021f0dc7bd6fa5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon start, the different opmodes are currently printing:
1. HW rev, which is already print by iwlwifi
2. The HW name (e.g. "Intel(R) Wi-Fi 7 BE201 320MHz")
cleanup things such as the hw rev won't be printed again, the HW name will
be printed by iwlwifi instead of each opmode.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240527190228.5c589c7abed0.I3590c4ee0ee99d1b207852c32d25d326afb327dd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
fw_running assumes that memory can be retrieved only after alive.
This assumption is no longer true as we support dump before alive.
To avoid invalid access to the NIC, check that STATUS_DEVICE_ENABLED
bit in trans status is set before dumping instead of the prior check.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.ca07138cedeb.I090e31d3eaeb4ba19f5f84aba997ccd36927e9ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While doing a passive scan, the firmware will report per-channel survey
information. This information is primarily useful for hostapd when doing
an ACS (Automatic Channel Selection). Collect this information and add
it to the result set when getting the survey information.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.9287591a5999.I54a3f9f6480d3694e67eea1cb4f5853beace2780@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When requested, the firmware can return per-channel survey information
generally used for ACS (automatic channel selection). Add the API for
this, which consists of a flag and a new channel survey notification.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.1facde532676.I3864ac4bc0fecb7fd5136e85c07585ab7100234b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The move of the scan complete notification handling to the wiphy worker
introduced a race between scan complete notification and scan abort:
- The wiphy lock is held, e.g., for rfkill handling etc.
- Scan complete notification is received but not handled yet.
- Scan abort is triggered, and scan abort is sent to the FW. Once the
scan abort command is sent successfully, the flow synchronously waits
for the scan complete notification. However, as the scan complete
notification was already received but not processed yet, this hangs for
a second and continues leaving the scan status in an inconsistent
state.
- Once scan complete handling is started (when the wiphy lock is not held)
since the scan status is not an inconsistent state, a warning is issued
and the scan complete notification is not handled.
To fix this issue, switch back the scan complete notification to be
asynchronously handling, and only move the link selection logic to
a worker (which was the original reason for the move to use wiphy lock).
While at it, refactor some prints to improve debug data.
Fixes: 07bf5297d3 ("wifi: iwlwifi: mvm: Implement new link selection algorithm")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.1f484a86324b.I63ed445a47f144546948c74ae6df85587fdb4ce3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there's an active link in a non-station vif, the station vif is
not allowed to enter EMLSR
Note that blocking EMLSR by calling iwl_mvm_block_esr() we will schedule
an exit from EMLSR worker, but the worker cannot run before the
activation of the non-BSS link, as ieee80211_remain_on_channel already
holds the wiphy mutex.
Handle that by explicitly calling ieee80211_set_active_links()
to leave EMLSR, and then doing iwl_mvm_block_esr() only for
consistency and to avoid re-entering it before ready.
Note that a call to ieee80211_set_active_links requires to release the
mvm mutex, but that's ok since we still hold the wiphy lock. The only
thing that might race here is the ESR_MODE_NOTIF, so this changes its
handler to run under the wiphy lock.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.916193759f8a.Idf3a3caf5cdc3e69c81710b7ceb57e87f2de87e4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replaces the current logic with a new algorithm based on the link
grading introduced in a previous patch.
The new selection algorithm will be invoked upon successful scan to ensure
it has the necessary updated data it needs.
This update delegates the selection logic as the primary link
determiner in EMLSR mode, storing it in mvmvif to avoid repeated
calculations, as the result may vary.
Additionally, includes tests for iwl_mvm_valid_link_pair to validate
link pairs for EMLSR.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240416134215.309fb1b3fe44.I5baf0c293c89a5a28bd1a6386bf9ca6d2bf61ab8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Send AP_TX_POWER_CONSTRAINTS_CMD with no local maximum transmit
power constraint to FW and FW will update the TPE element with
required tx power limits.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240416134215.b6af4ecfcfe8.I07e8db349190e0c58c468c18477d8551288ac069@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Miri Korenblit
Emmanuel Grumbach
Johannes Berg
Somashekhar(Som)
Yedidya Benshimol
Peter Zijlstra
Jakub Kicinski
Daniel Gabay
Shaul Triebitz
Shahar S Matityahu
Benjamin Berg
Ilan Peer
Mukesh Sisodiya