Cross-merge networking fixes after downstream PR (net-6.14-rc6).
Conflicts:
tools/testing/selftests/drivers/net/ping.py
75cc19c8ff ("selftests: drv-net: add xdp cases for ping.py")
de94e86974 ("selftests: drv-net: store addresses in dict indexed by ipver")
https://lore.kernel.org/netdev/20250311115758.17a1d414@canb.auug.org.au/
net/core/devmem.c
a70f891e0f ("net: devmem: do not WARN conditionally after netdev_rx_queue_restart()")
1d22d3060b ("net: drop rtnl_lock for queue_mgmt operations")
https://lore.kernel.org/netdev/20250313114929.43744df1@canb.auug.org.au/
Adjacent changes:
tools/testing/selftests/net/Makefile
6f50175cca ("selftests: Add IPv6 link-local address generation tests for GRE devices.")
2e5584e0f9 ("selftests/net: expand cmsg_ipv6.sh with ipv4")
drivers/net/ethernet/broadcom/bnxt/bnxt.c
661958552e ("eth: bnxt: do not use BNXT_VNIC_NTUPLE unconditionally in queue restart logic")
fe96d717d3 ("bnxt_en: Extend queue stop/start for TX rings")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When MSI-X is not enabled, we mask all the interrupts in the interrupt
handler and re-enable them when the interrupt thread runs. If
STATUS_INT_ENABLED is not set, we won't re-enable in the thread.
In order to get the ALIVE interrupt, we allow the ALIVE interrupt
itself, and RX as well in order to receive the ALIVE notification (which
is received as an RX from the firmware.
The problem is that STATUS_INT_ENABLED is clear until the op_mode calls
trans_fw_alive which means that until trans_fw_alive is called, any
notification from the firmware will not be received.
This became a problem when we inserted the pnvm_load exactly between the
ALIVE and trans_fw_alive.
Fix that by calling trans_fw_alive before loading the PNVM. This will
allow to get the notification from the firmware about PNVM load being
complete and continue the flow normally.
This didn't happen on MSI-X because we don't disable the interrupts in
the ISR when MSI-X is available.
The error in the log looks like this:
iwlwifi 0000:00:03.0: Timeout waiting for PNVM load!
iwlwifi 0000:00:03.0: Failed to start RT ucode: -110
iwlwifi 0000:00:03.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
Fixes: 70d3ca86b0 ("iwlwifi: mvm: ring the doorbell and wait for PNVM load completion")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250306122425.0f2cf207aae1.I025d8f724b44f52eadf6c19069352eb9275613a8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Created a common function iwl_add_mcc_to_tas_block_list() to handle the
operations previously performed by iwl_mld_add_to_tas_block_list() and
iwl_mvm_add_to_tas_block_list(). moved this new function to regulatory.c
to better reflect its purpose and improve code organization.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.157d26fb7f02.I87e20e967835bc895be390daf1c6637e20b52aae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Renamed iwl_mvm_eval_dsm_rfi() to iwl_rfi_is_enabled_in_bios() to better
reflect the function's operation. Additionally, moved the function to the
regulatory.c file for better organization. optimize local variable
usage in it.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205145347.b7ac9d05234e.Ieb623d7e8dca6bb6a5733682b31e4ff1e39373f0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend TAS_CONFIG to send exact data read from bios to firmware
without filtering/altering bios data. This enables driver becoming
purely a pipe for TAS features.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.f46d58e7cfd1.Ifd81e632fa3e7039b8d139ee0d1c24e09669dff5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TOP is a shared (between BT and WiFi) hardware component,
and if it has an error we need to reset the whole device, i.e.
both BT and WiFi. This is achieved by calling a specific ACPI
DSM (device-specific method) with the right arguments before
doing a reset via the object referenced by _PRR.
Since this is needed here, but a function reset will always do
better than just re-enumerating the bus in case of errors, we
can always try to at least do a function reset and do the full
product reset only when needed for TOP errors.
Also, for some Bz and Sc devices where BT is PCIe/IOSF as well,
find the BT device and unbind that device as well so the BT
driver can recover from the reset that's going to happen,
rather than having to somehow detect that the device was reset.
Also add - currently unused - the function reset mode, this is
going to get used in the upcoming escalation model.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.5b0f846d3e13.Ia14ccac38ac3d48adf5f341b17c7e34ccc41c065@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
extend TAS table support to revision 2 for getting UHB canada
enablement from BIOS and send to firmware via TAS_CONFIG cmd
based on firmware capability. While on it fixed kernel-doc for
struct iwl_tas_config_cmd_v4.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241226174257.0b1d92ad59b8.Ib80f8514a64fc2800a2a20131e730c2bd9c4c4af@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most likely the last -next pull request for v6.13. Most changes are in
Realtek and Qualcomm drivers, otherwise not really anything
noteworthy.
Major changes:
mac80211
* EHT 1024 aggregation size for transmissions
ath12k
* switch to using wiphy_lock() and remove ar->conf_mutex
* firmware coredump collection support
* add debugfs support for a multitude of statistics
ath11k
* dt: document WCN6855 hardware inputs
ath9k
* remove include/linux/ath9k_platform.h
ath5k
* Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
rtw88:
* 8821au and 8812au USB adapters support
rtw89
* thermal protection
* firmware secure boot for WiFi 6 chip
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmc04UYRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuckgf/RV0zy8gMuzJ/cSk1GDKoOYmEwAZ4JvtW
teAKghsODDW/bng2iKnXphJyx3spZRCNuvOmfPcHsWoResX+vqrKJOaER/3159OF
68xAPZNXPRF4M693IpIUB/P3uTw/jieXPI7ftSPuUOhStca/ALwQd5Lp3kNKkVtq
HipXJwCenVS7Hd8DdHbpvYFUckRWr3tHPFlOgG3qOQOVvfRen2z9rhM14oK9rn+h
f309ATHKTbpTKNagOPYAYcyHs3zE59hlVRgRqHL7Ew0a0HI8uPJ4KK2n5W6tZJFN
swhoQolc1uXrRYlZ3Bdr7mKSIqt557kRz7NJ9ITe7KKCU0CxM/7nhQ==
=v8bS
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.13
Most likely the last -next pull request for v6.13. Most changes are in
Realtek and Qualcomm drivers, otherwise not really anything
noteworthy.
Major changes:
mac80211
* EHT 1024 aggregation size for transmissions
ath12k
* switch to using wiphy_lock() and remove ar->conf_mutex
* firmware coredump collection support
* add debugfs support for a multitude of statistics
ath11k
* dt: document WCN6855 hardware inputs
ath9k
* remove include/linux/ath9k_platform.h
ath5k
* Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
rtw88:
* 8821au and 8812au USB adapters support
rtw89
* thermal protection
* firmware secure boot for WiFi 6 chip
* tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (154 commits)
Revert "wifi: iwlegacy: do not skip frames with bad FCS"
wifi: mac80211: pass MBSSID config by reference
wifi: mac80211: Support EHT 1024 aggregation size in TX
net: rfkill: gpio: Add check for clk_enable()
wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw()
wifi: Switch back to struct platform_driver::remove()
wifi: ipw2x00: libipw_rx_any(): fix bad alignment
wifi: brcmfmac: release 'root' node in all execution paths
wifi: iwlwifi: mvm: don't call power_update_mac in fast suspend
wifi: iwlwifi: s/IWL_MVM_INVALID_STA/IWL_INVALID_STA
wifi: iwlwifi: bump minimum API version in BZ/SC to 92
wifi: iwlwifi: move IWL_LMAC_*_INDEX to fw/api/context.h
wifi: iwlwifi: be less noisy if the NIC is dead in S3
wifi: iwlwifi: mvm: tell iwlmei when we finished suspending
wifi: iwlwifi: allow fast resume on ax200
wifi: iwlwifi: mvm: support new initiator and responder command version
wifi: iwlwifi: mvm: use wiphy locked debugfs for low-latency
wifi: iwlwifi: mvm: MLO scan upon channel condition degradation
wifi: iwlwifi: mvm: support new versions of the wowlan APIs
wifi: iwlwifi: mvm: allow always calling iwl_mvm_get_bss_vif()
...
====================
Link: https://patch.msgid.link/20241113172918.A8A11C4CEC3@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is written only with wiphy and mvm mutexes held, but in
order to actually rely on that document it and add lockdep
assertions to ensure it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241028135215.a6c6aa4147cf.If7f1b30a7b92ce5e9226e8972201a20aa9905108@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1. The size of the response packet is not validated.
2. The response buffer is not freed.
Resolve these issues by switching to iwl_mvm_send_cmd_status(),
which handles both size validation and frees the buffer.
Fixes: f130bb75d8 ("iwlwifi: add FW recovery flow")
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241010140328.76c73185951e.Id3b6ca82ced2081f5ee4f33c997491d0ebda83f7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Rename iwl_dev_tx_power_cmd to iwl_dev_tx_power_cmd_v3_v8
* struct iwl_dev_tx_power_common needs to be packed. It was always the
case, but now that its size is not a multiple of 4, it becomes
meaningful.
* Move per_band data out of the common structure since it won't be
present in the new versions of the command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240729201718.8da29a66984f.I922bdef4740d990f98cb452e858c4157bbc491c5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This causes unnecessary error level kernel messages if the platform
does not have any UATS table.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240625194805.306b7eed8671.I6e9294335378dab38ef957866a0d39ec1a2df7f8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the firmware has MLD APIs, it will handle all timing and we
don't need to give it timestamps. Therefore, we don't care about
the timestamps stored in the BSS table, so there's no need to
flush the BSS table.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240625194805.c6d86dc2377e.I246d0fae0d23ed34b7cd9c3400edb004eb5ac1d0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When UATS isn't enabled (no VLP/AFC AP support), we need to still
set the right bits in the channel/regulatory flags, so remove the
uats_enabled argument to the parsing etc.
Also, firmware deals just fine with getting the UATS table if it
supports the command even if the bits aren't set, so always send
it, since it's also needed if BIT(31) is set, but the driver need
not have any knowledge of that. Remove 'uats_enabled' entirely.
Fixes: 0d2fc8821a ("wifi: iwlwifi: nvm: parse the VLP/AFC bit from regulatory")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240618195731.a81e7234c4f6.Ic0131180d38e0f1ead2f7fa0e7583407ceaa0bd1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PLDR (product level device reset) is a Windows term, and
is something the driver triggers there, AFAICT.
Really what 'pldr_sync' here wants to capture is whether
or not the firmware will/may do a product reset during
initialization, which makes the device drop off the bus,
requiring a rescan. If this is the case, obviously the
init will fail/time out, so we don't want to report all
kinds of errors etc., hence this tracking variable.
Rename it to 'fw_product_reset' to capture the meaning
better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240618194245.ccf849642af8.I01dded6b2393771b7baf8b4b17336784d987c7c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have two
conflicts this time:
CONFLICT (content): Merge conflict in net/mac80211/cfg.c
CONFLICT (content): Merge conflict in drivers/net/wireless/microchip/wilc1000/netdev.c
Here are Stephen's resolutions for them:
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au/https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au/
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* Enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA) support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZi07URHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu3/QgAo7jyKgvpwMaNIVRLyfYCo0r3Q9wb7QPd
QeRNsftYxlWpPTJ4+Y95aZupy91Ay+RaEQXbbtl7PMIiyQrs7wb4V4Iqzedkws3t
DZsR5BitH+1BIGY0Omo0fiSB5HlWEwZGUj6inqlgKHpBtdIVTANSMjuwkdoMAV5y
ZU57axIGToySvDbRlhJQW833Nnh4KnaseA+TtyfXSaBVerzbshkjBr0d9pMBMiH9
irMQW5CW+7fbxp3OCNsKxX4eG6MFGmm/uP1hFmeYQi2qzUE4SddHMeV4I6oNKOrH
vFB+ZVmYvOjJUYsNhlCUe6Vy+EKwvmfiDWwE1egelEkgozCixJXAAQ==
=QT4C
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
The first "new features" pull request for v6.11 with changes both in
stack and in drivers. Nothing out of ordinary, except that we have
two conflicts this time:
net/mac80211/cfg.c
https://lore.kernel.org/all/20240531124415.05b25e7a@canb.auug.org.au
drivers/net/wireless/microchip/wilc1000/netdev.c
https://lore.kernel.org/all/20240603110023.23572803@canb.auug.org.au
Major changes:
cfg80211/mac80211
* parse Transmit Power Envelope (TPE) data in mac80211 instead of in drivers
wilc1000
* read MAC address during probe to make it visible to user space
iwlwifi
* bump FW API to 91 for BZ/SC devices
* report 64-bit radiotap timestamp
* enable P2P low latency by default
* handle Transmit Power Envelope (TPE) advertised by AP
* start using guard()
rtlwifi
* RTL8192DU support
ath12k
* remove unsupported tx monitor handling
* channel 2 in 6 GHz band support
* Spatial Multiplexing Power Save (SMPS) in 6 GHz band support
* multiple BSSID (MBSSID) and Enhanced Multi-BSSID Advertisements (EMA)
support
* dynamic VLAN support
* add panic handler for resetting the firmware state
ath10k
* add qcom,no-msa-ready-indicator Device Tree property
* LED support for various chipsets
* tag 'wireless-next-2024-06-07' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (194 commits)
wifi: ath12k: add hw_link_id in ath12k_pdev
wifi: ath12k: add panic handler
wifi: rtw89: chan: Use swap() in rtw89_swap_sub_entity()
wifi: brcm80211: remove unused structs
wifi: brcm80211: use sizeof(*pointer) instead of sizeof(type)
wifi: ath12k: do not process consecutive RDDM event
dt-bindings: net: wireless: ath11k: Drop "qcom,ipq8074-wcss-pil" from example
wifi: ath12k: fix memory leak in ath12k_dp_rx_peer_frag_setup()
wifi: rtlwifi: handle return value of usb init TX/RX
wifi: rtlwifi: Enable the new rtl8192du driver
wifi: rtlwifi: Add rtl8192du/sw.c
wifi: rtlwifi: Constify rtl_hal_cfg.{ops,usb_interface_cfg} and rtl_priv.cfg
wifi: rtlwifi: Add rtl8192du/dm.{c,h}
wifi: rtlwifi: Add rtl8192du/fw.{c,h} and rtl8192du/led.{c,h}
wifi: rtlwifi: Add rtl8192du/rf.{c,h}
wifi: rtlwifi: Add rtl8192du/trx.{c,h}
wifi: rtlwifi: Add rtl8192du/phy.{c,h}
wifi: rtlwifi: Add rtl8192du/hw.{c,h}
wifi: rtlwifi: Add new members to struct rtl_priv for RTL8192DU
wifi: rtlwifi: Add rtl8192du/table.{c,h}
...
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
====================
Link: https://lore.kernel.org/r/20240607093517.41394C2BBFC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case the firmware sends a notification that claims it has more data
than it has, we will read past that was allocated for the notification.
Remove the print of the buffer, we won't see it by default. If needed,
we can see the content with tracing.
This was reported by KFENCE.
Fixes: bdccdb854f ("iwlwifi: mvm: support MFUART dump in case of MFUART assert")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.ba82a01a559e.Ia91dd20f5e1ca1ad380b95e68aebf2794f553d9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since IWL_FW_CMD_VER_UNKNOWN = 99, then my change to consider
cmd_ver >= 7 instead of cmd_ver = 7 included also firmwares that don't
advertise the command version at all. This made us send a command with a
bad size and because of that, the firmware hit a BAD_COMMAND immediately
after handling the REDUCE_TX_POWER_CMD command.
Fixes: 8f892e225f ("wifi: iwlwifi: mvm: support iwl_dev_tx_power_cmd_v8")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512072733.eb20ff5050d3.Ie4fc6f5496cd296fd6ff20d15e98676f28a3cccd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We track which link is using which FW link ID, so there
really isn't a need to separately track which link IDs
are in use. Remove that code and check the table when
looking for a new link ID to use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512072733.1a67d8af815f.Ie642c12dce3ab55c688abd9a25918569e83e558a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware has different names for this, which is confusing
as even the convention of having the firmware name in a comment
after the struct definition wasn't met here. Fix the naming,
but keep UATS in some of it since that's the BIOS name.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240506095953.b0dfe17d5f44.I8f5f5a831c7b934ce3140f838315827c018103bb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for enable/disable 320 MHz for Japan and South Korea
by reading WBEM (WiFi Bandwidth Enablement per MCC) variable from
UEFI or ACPI and sending it to the FW.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415114847.7946c3befbe1.I453c33f7ea48156ea2a3961f50a9003103fca5a5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a requirement from OEMs to support new bits in DSM function 7,
which will indicate enablement of 5.9 GHz in Canada.
Add support for this by reading those bits from BIOS and sending it to the
FW. mask unii4 allow bitmap based on LARI_CONFIG_CHANGE_CMD version
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.5c31ccd73119.I0363992efc3607368648d34a7918b2534150a3ca@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With C99 bool we really also should use true/false, not the
upper-case variants, wherever they may actually be coming
from. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240208185302.5732dd306ee9.Ifc07c026ac3779429e3dc949e96c9437e89f7bf9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BIOS tables SGOM and UATS are read from UEFI, but require
additional tables (WGDS and DSM func 3, respectively) which used to be
read from ACPI only, so the code handling those tables had to be under
ifdef ACPI. But now the driver reads those tables (WGDS and DSM) from
both ACPI and UEFI, so SGOM and UATS code shouldn't be under ifdef ACPI
anymore.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240205211151.dcaa3325773f.I649079c842369dcae3a362842322deca422a61d5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
dmi_get_system_info() will statically return NULL when the
kernel is compiled without CONFIG_DMI, leading to compiler
warnings. Fix that by printing "<unknown>" in that case.
Fixes: c3f40c3e02 ("iwlwifi: mvm: add US/CA to TAS block list if OEM isn't allowed")
Fixes: 9457077df4 ("wifi: iwlwifi: mvm: Add debugfs to get TAS status")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For each DSM function, try to first read it from the UEFI.
If the UEFI WIFI GUID is unclocked, or the DSM function in
UEFI is invalid/unavailable - read it from ACPI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.27dd626ce2bd.Ib90bab74a9d56deb2362edb712294360e4ddae5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move all the common items (functions, enumerations and mcaros)
to regulatory.h/c files, and rename it to a common name.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.eae9bcbc0023.If1175f3143d6369076669ddd5d6ad4df0ee00659@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As DSMs are going to be read from UEFI too, we need a unified API
to get DSMs for both ACPI and UEFI.
The difference in getting DSM in each one of these methods (ACPI, UEFI)
is in the GUID, revision (0 for ACPI, 4 for UEFI), and size of the DSM
values (8 or 32 for ACPI, 32 for UEFI).
Therefore, change the iwl_acpi_get_dsm_x() to iwl_acpi_get_dsm() which
determines the GUID, revision (these two are the same for all WiFi DSMs),
and size (based on a func-to-size mapping) internally.
While at it, fix DSM_FUNC_RFI_CONFIG to expect a 32-bit value
(as defined in Intel BIOS spec) and not a 8-bit one.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1bcd7072a7a5.I344ee0a11abbc27da0c693187d1b8bee653aaeef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These functions shouldn't be ACPI_CONFIG dependent, as they don't
access the ACPI. The functions that really access ACPI -
already handle the case that CONFIG_ACPI is not set.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.1412e6d561f8.I84f67478d01b576457e1bf489fbcb044adfda6fe@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the ECKV table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI.
Change iwl_acpi_get_eckv() to receive fwrt as argument so
it will be the same as all iwl_acpi_get_x() functions,
so it could be generated by the macro.
While at it - move the reading of ECKV to INIT stage. There is no
reason to read it each time we load the FW.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.d4937cc00727.I36e5fc7f7850229b9b377c80b5203aa47137c97c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the WTAS table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.45e6ff7b5063.Id3aec70887e14533b10d564f32c0cf5f2a14b792@changeid
[move uefi_tables_lock_status outside ifdef to fix build errors]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the TAS 'read-from-BIOS' flow receives the command struct
and the version of it as read from FW TLVs, and fills the command
accordingly.
This seems wrong, we should have the 'read-from-BIOS' flow
(iwl_acpi_get_tas in iwlwifi) reading/parsing/validating the table from
BIOS, and the 'send-to-FW' flow (iwl_mvm_tas_init) doing
all the FW versioning checks and cmd filling.
Move the cmd filling to the 'send-to-fw' flow.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.24df27772a71.I57b702af4feb3f38dc21d52593c25de4b1999e4b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We are going to support reading BIOS tables from UEFI
too, Refactor the TAS table flow:
1. Rename and move the common code to the regulatory.h/c files.
2. Remove the IWL_TAS_BLOCK_LIST_MAX, as we can use IWL_WTAS_BLACK_LIST_MAX
instead.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.0c2197cf1feb.Ib0e83d5bd3f4d5cfa9c3d2925317ba49377d257f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Try to read the PPAG table from UEFI first,
and if the WIFI UEFI tables are unlocked or the
table doesn't exist - try to read it from ACPI
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.6516da09aec1.I0dcaf0b6d8857417ba1318467a28da5d0d7d7f27@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As PPAG table is going to be read from UEFI, there are some
cleanups required:
Move functions/definitions that are common to both UEFI and ACPI to
regulatory.h/c.
In addition, rename the functions/macros names so it will be clear which
one is ACPI specific, and which is common for ACPI and UEFI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.25623670b422.I8132af7517e4faf0ea8cbeb2efe9651edd319b98@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1. The name of iwl_read_ppag_table is misleading, as this function only
fills the command structure from the previously read table. Rename it.
2. Don't initialize fwrt::ppag_flags to 0 as the entire fwrt is zeroed
in the INIT stage anyway.
3. Don't filter out the reserved bits from fwrt::ppag_flags when printing
it, as it is already done in 'read-from-bios' flow.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.48acf340e817.I810e457b80015c1931d96d3e13c849f0339723c3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the regulatory tables will be read from UEFI, and
only if it doesn't exist - they will be read from ACPI.
Read SAR tables (WRDS, EWRD and WGDS) from UEFI.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.533b687e1efb.Icb316291e593c8d53f41fdea2d083367dc97e3c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_geo_tx_power_profiles_cmd::table_revision indicates whether
to use South Korea scheme or not.
We use South Korea scheme if the revision of WGDS table is 1.
We used to read the WGDS table from ACPI inside iwl_sar_geo_fill_table(),
so we had to set table_revision only after the call to it.
This added an extra if...else for each cmd version.
But it has been a while since we moved the BIOS tables reading to
INIT stage, and iwl_sar_geo_fill_table() is now only copying the
previously stored table to the cmd structure.
Set the table_revision before the call to iwl_sar_geo_fill_table()
and avoid that extra if...else.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.17a2384d4535.I306570874f1da0c6345066ebbf74a04b6c8aeb37@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver will support reading BIOS tables from UEFI
too. Refactor the SAR tables (WRDS, EWRD, WGDS) flows:
1. Move all the SAR logic/definitions that is common to both
UEFI and ACPI to a new file - regulatory.h/c.
2. Rename the relevant functions/definitions
so it will be clear which is ACPI specific and which is
for both ACPI and UEFI
3. Rename the function that copies the stored tables into the different
commands structures, so will be clear what these functions do.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240131091413.429a9baff34a.I040460348aa1b43609be3a317b86722d6be71c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All the regulatory tables from BIOS are going to be loaded
(preferably) from the UEFI instead of the ACPI.
There is a security issue with the fact that anyone can
add these UEFI variables.
The solution for that is to have a lock for all WIFI GUID UEFI
variables, and only if the UEFI variables are locked then we can
read it.
The status of the lock (unlocked, locked, test mode) is indicated
in a ACPI table: Guid Lock ACPI Indicator.
Load this table so the driver knows whether to read from UEFI or
not
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240128084842.53994809fbdd.I1bd10aafc387bc04f375e386861ee2bcb82f0a61@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow to reconnect immediately instead of leaving the
connection in a limbo state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240128084842.e90531cd3a36.Iebdc9483983c0d8497f9dcf9d79ec37332a5fdcc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Paolo Abeni
Emmanuel Grumbach
Anjaneyulu
Johannes Berg
Jakub Kicinski
Miri Korenblit
Daniel Gabay
Benjamin Berg