The imx214 camera is capable of either two-lane or four-lane operation.
Currently only the four-lane mode is supported, as proper pixel rates
and link frequences for the two-lane mode are unknown.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The IMX214_REG_EXPOSURE is configured twice, once with a hardcoded value
in the mode_<res> registers arrays, and once via v4l2_ctrl_ops. The
latter is enough, drop the former.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Define macros for all the known registers used in the register arrays,
and use them to replace the numerical addresses. This improves
readability.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Use the new common CCI register access helpers to replace the private
register access helpers in the imx214 driver. This simplifies the driver
by reducing the amount of code.
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Error handling in probe() can be a bit simpler with dev_err_probe().
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Port the imx214 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
While at it, simplify imx214_start_streaming() by removing unneeded goto
statements and the corresponding error label.
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
There were multiple issues in the driver's probe function related to
error handling:
- Device's PM runtime status wasn't reverted to suspended on some errors
in probe.
- Runtime PM was left enabled for the device on some probe errors.
- Device was left powered on if a probe failure happened or when it
was removed when it was powered on.
- An extra pm_runtime_set_suspended() was issued in driver's remove
function when the device was suspended.
Fix these bugs.
Fixes: 4361905962 ("media: imx214: Add imx214 camera sensor driver")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: André Apitzsch <git@apitzsch.eu>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
This reverts commit 9bc92332cc.
Revert this "fix" as it's not really helpful but makes backporting a
proper fix harder.
Fixes: 9bc92332cc ("media: imx214: Fix the error handling in imx214_probe()")
Cc: stable@vger.kernel.org # for >= v6.12
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
All ov08x40_check_hwcfg() error-exit paths already log a detailed reason,
logging a second generic "failed to check hwcfg" error is not useful, and
in case of the fwnode check failing with -EPROBE_DEFER this is outright
problematic flooding the log with:
[ 4.557059] ov08x40 i2c-OVTI08F4:00: failed to check hwcfg: -517
[ 4.559636] ov08x40 i2c-OVTI08F4:00: failed to check hwcfg: -517
etc.
messages.
The one exception to all ov08x40_check_hwcfg() error-exit paths already
logging an error is on v4l2_fwnode_endpoint_alloc_parse() errors.
Make ov08x40_check_hwcfg() log an error in that case too and drop
the duplicate "failed to check hwcfg: %d\n" error logging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
A number of dev_err() error messages miss a terminating '\n', add
the missing '\n' to these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The driver might skip the ov08x40_identify_module() on probe() based on
the acpi_dev_state_d0() check done in probe().
If the ov08x40_identify_module() call is skipped on probe() it should
be done on the first stream start. Add the missing call.
Note ov08x40_identify_module() will only do something on its first call,
subsequent calls are no-ops.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: b1a42fde6e ("media: ov08x40: Avoid sensor probing in D0 state")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Improve ov08x40_[read|write]_reg() error returns, if we got an errno value
from the I2C core use that instead of always returning -EIO.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
ov08x40_identify_module() already logs an error if the read ID mismatches,
so having its caller also log an error results in 2 errors in this case.
Add error logging to the ID register read in ov08x40_identify_module() and
drop the error logging in the caller.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Move the ov08x40_identify_module() function to above ov08x40_set_stream()
this is a preparation patch for adding a missing ov08x40_identify_module()
call to ov08x40_set_stream().
No functional changes, just moving code around.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
ACPI platforms might also have a clk provider which needs to be controlled,
always try to get a clk using clk_get_optional() and when that fails fall
back to getting the xvclk frequency from the "clock-frequency" property.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
ACPI platforms might also have a reset GPIO and regulators, move the code
to get these outside of the if (!is_acpi_node(fwnode)) check.
This also removes the is_acpi_node(fwnode) checks from ov08x40_power_on() /
ov08x40_power_off() both the GPIO hand the clk frameworks functions used
there will happily accept the NULL pointer returned from the optional get()
functions when there is no reset GPIO / no clk.
While moving the code around also at error logging to the error exit
path for getting the reset GPIO.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
If the bridge has not yet setup the fwnode-graph then
the fwnode_property_read_u32("clock-frequency") call will fail.
Make the fwnode_graph_get_next_endpoint() call the first call in
ov08x40_check_hwcfg() and return -EPROBE_DEFER if it fails.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Commit df1ae2251a ("media: ov08x40: Add OF probe support") added support
for a reset GPIO, regulators and a clk provider controlled through new
ov08x40_power_off() and ov08x40_power_on() functions.
But it missed adding a pm ops structure to call these functions on
runtime suspend/resume. Add the missing pm ops and only call
ov08x40_power_off() on remove() when not already runtime-suspended
to avoid unbalanced regulator / clock disable calls.
Fixes: df1ae2251a ("media: ov08x40: Add OF probe support")
Cc: stable@vger.kernel.org
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
All hi556_check_hwcfg() error-exit paths already log a detailed reason,
logging a second generic "failed to check HW configuration" error is not
useful, and in case of the fwnode check failing with -EPROBE_DEFER this
is outright problematic flooding the log with:
[ 6.336318] hi556 i2c-INT3537:00: failed to check HW configuration: -517
[ 6.339006] hi556 i2c-INT3537:00: failed to check HW configuration: -517
[ 6.346293] hi556 i2c-INT3537:00: failed to check HW configuration: -517
[ 6.356129] hi556 i2c-INT3537:00: failed to check HW configuration: -517
[ 6.380316] hi556 i2c-INT3537:00: failed to check HW configuration: -517
etc.
The one exception to all hi556_check_hwcfg() error-exit paths already
logging an error is on v4l2_fwnode_endpoint_alloc_parse() errors.
Make hi556_check_hwcfg() log an error in that case too and drop
the duplicate "failed to check HW configuration" error logging.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2307279
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The hi556 driver waits for the endpoint fwnode to show up in case this
fwnode is created by a bridge-driver.
It does this by returning -EPROBE_DEFER, but it does not use
dev_err_probe() so no reason for deferring gets registered.
After 30 seconds the kernel logs a warning that the probe is still
deferred, which looks like this:
[ 33.952052] i2c i2c-INT3537:00: deferred probe pending: (reason unknown)
Use dev_err_probe() when returning -EPROBE_DEFER to register the probe
deferral reason changing the error to:
deferred probe pending: waiting for fwnode graph endpoint
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Many hi556 dev_err() error messages miss a terminating '\n', add
the missing '\n' to these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Commit 7d968b5bad ("media: hi556: Return -EPROBE_DEFER if no endpoint is
found") moved the v4l2_fwnode_endpoint_alloc_parse() call in
hi556_check_hwcfg() up, but it did not make the error-exit paths between
the old and new call-site use "goto check_hwcfg_error;" to free the bus_cfg
on errors.
Add the missing "goto check_hwcfg_error;" statements to fix a memleak on
early error-exits from hi556_check_hwcfg().
Fixes: 7d968b5bad ("media: hi556: Return -EPROBE_DEFER if no endpoint is found")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
-----BEGIN PGP SIGNATURE-----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=ktuX
-----END PGP SIGNATURE-----
Merge tag 'media/v6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Sensor driver fixes
- remove dead TI wl128x FM radio driver
- Add support for the imx462 sensor at the IMX290 binding
- V4L2 pixel data transmitter and receiver documentation improvements
- Add support for MIPI Discovery and Configuration for C-PHY line
orders
- imx8-isi fixes and improvements
- stm32: dcmipp: add core support for the stm32mp25
- qcom: camss: Add sc7280 support
- Various fixes and enhancements
* tag 'media/v6.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (152 commits)
media: nuvoton: Fix an error check in npcm_video_ece_init()
media: dvb-usb-v2: af9035: fix ISO C90 compilation error on af9035_i2c_master_xfer
media: platform: rzg2l-cru: rzg2l-video: Fix the comment in rzg2l_cru_start_streaming_vq()
media: fix secfeed undefined when filter alloc fail
media: dt-bindings: trivial white-space and example cleanup
MAINTAINERS: repair file entry in MEDIA DRIVERS FOR STM32 - CSI
media: solo6x10: Use const 'struct bin_attribute' callback
media: saa7164: Remove unused values
staging: media: imx: fix OF node leak in imx_media_add_of_subdevs()
media: platform: exynos4-is: Remove unused __is_get_frame_size
media: vidtv: Fix a null-ptr-deref in vidtv_mux_stop_thread
media: mmp: Bring back registration of the device
media: cec: include linux/debugfs.h and linux/seq_file.h where needed
Revert "media: qcom: camss: Restructure camss_link_entities"
media: venus: Remove unused hfi_core_ping()
media: dt-bindings: qcom-venus: Deprecate video-decoder and video-encoder where applicable
media: venus: Populate video encoder/decoder nodename entries
media: venus: Add support for static video encoder/decoder declarations
media: venus: match instance creation and destruction order
media: venus: destroy hfi session after m2m_ctx release
...
The sysfs core now provides callback variants that explicitly take a
const pointer. Make use of it to match the attribute definition.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On some designs the regulators for the AVDD / DOVDD / DVDD power rails
are controlled by Linux.
Add support to the driver for getting regulators for these 3 rails and
for enabling these regulators when necessary.
The datasheet specifies a delay of 0ns between enabling the regulators,
IOW they can all 3 be enabled at the same time. This allows using the bulk
regulator API.
The regulator core will provide dummy regulators for the 3 power-rails
when necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov2740 sensor has both reset and power_down inputs according to
the datasheet one or the other should always be tied to DOVDD but on
some designs both are attached to GPIOs.
Add support for controlling both a reset and a powerdown GPIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Acked-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add camera orientation and sensor rotation controls using
the v4l2_fwnode_device_parse() and v4l2_ctrl_new_fwnode_properties()
helpers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Calling the identify function may get delayed till the first stream-on,
add a dev_dbg() to it so that we know when it has run. This is useful
to debug bring-up problems related to regulators / clks / GPIOs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Light frequency was not properly returned when in auto
mode and the detected frequency was 60Hz.
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Sam Bobrowicz <sam@elite-embedded.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix a few cases where a local shadows a previously declared local of the
same name.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add error handling for i2c reads/writes in various places.
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Closes: https://lore.kernel.org/all/Zv40EQSR__JDN_0M@kekkonen.localdomain/
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add error handling to ub913_hw_init() using a new helper function,
ub913_update_bits().
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Closes: https://lore.kernel.org/all/Zv40EQSR__JDN_0M@kekkonen.localdomain/
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We currently sleep for 50 ms at the end of each iteration in
ub960_rxport_wait_locks(). This feels a bit excessive, especially as we
always do at least two loops, so there's always at least one sleep, even
if we already have a stable lock.
Change the sleep to 10 ms.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drop the unused UB960_IND_TARGET_CSI_CSIPLL_REG_1 define. It does not
even match to any block in the more recent documents, so it's possible
it is not only unused but also wrong.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Clear the CRC error counter after showing it in ub953_log_status() to
make its behavior match the other counter values.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add RGB24 and RAW8 and RAW10 bayer formats. RGB24 is mostly for TPG
purposes, but RAW8 and RAW10 are widely used by sensors.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Normally the driver accesses both the RX and the TX port registers via a
paging mechanism: one register is used to select the page (i.e. the
port), which dictates the port used when accessing the port specific
registers.
The downside to this is that while debugging it's almost impossible to
access the port specific registers from the userspace, as the driver can
change the page at any moment.
The hardware supports another access mechanism: using the I2C_RX_ID
registers (one for each RX port), i2c addresses can be chosen which,
when accessed, will always use the specific port's registers, skipping
the paging mechanism.
The support is only for the RX port, but it has proven very handy while
debugging and testing. So let's add the code for this, but hide it
behind a disabled define.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use HZ_PER_MHZ instead of 1000000U.
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver uses a static CSI-2 virtual channel mapping where all virtual
channels from an RX port are mapped to a virtual channel number matching
the RX port number.
The UB960 and UB9702 have different registers for the purpose, and the
UB9702 version is not correct. Each of the VC_ID_MAP registers do not
contain a single mapping, as the driver currently thinks, but two.
This can cause received VCs other than 0 to be mapped in a wrong way.
Fix this by writing both mappings to each register.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UB9702 does not have SP and EQ registers, but the driver uses them in
log_status(). Fix this by separating the SP and EQ related log_status()
work into a separate function (for clarity) and calling that function
only for UB960.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UB9702 doesn't have the registers for SP and EQ. Adjust the code in
ub960_rxport_wait_locks() to not use those registers for UB9702. As
these values are only used for a debug print here, there's no functional
change.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
UB9702 has the refclk freq register at a different offset than UB960,
but the code uses the UB960's offset for both chips. Fix this.
The refclk freq is only used for a debug print, so there's no functional
change here.
Cc: stable@vger.kernel.org
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ub913 and ub953 drivers call fwnode_handle_put(priv->sd.fwnode) as
part of their remove process, and if the driver is removed multiple
times, eventually leads to put "overflow", possibly causing memory
corruption or crash.
The fwnode_handle_put() is a leftover from commit 905f88cceb ("media:
i2c: ds90ub9x3: Fix sub-device matching"), which changed the code
related to the sd.fwnode, but missed removing these fwnode_handle_put()
calls.
Cc: stable@vger.kernel.org
Fixes: 905f88cceb ("media: i2c: ds90ub9x3: Fix sub-device matching")
Reviewed-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
No need to continue probing when the CCS static data parser fails. Improve
this by checking the return value and correctly exiting on failure.
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Besides returning an error, also print a warning when
ccs_data_parse() fails.
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The datasheet lists that "Maximum exposure time is frame
length -25 row periods, where frame length is set by
registers {0x380E, 0x380F}".
However this driver had OV9282_EXPOSURE_OFFSET set to 12
which allowed that restriction to be violated, and would
result in very under-exposed images.
Correct the offset.
Fixes: 14ea315bbe ("media: i2c: Add ov9282 camera sensor driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ccs_limits is allocated in ccs_read_all_limits() after the allocation of
mdata.backing. Ensure that resources are freed in the reverse order of
their allocation by moving out_free_ccs_limits up.
Fixes: a11d3d6891 ("media: ccs: Read CCS static data from firmware binaries")
Cc: stable@vger.kernel.org
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a 2-5ms delay when coming out of standby and before reading the
sensor info register durning probe, as instructed by the datasheet. This
standby delay is already present when the sensor starts streaming.
During a cold-boot, reading the IMX296_SENSOR_INFO register would often
return a value of 0x0000, if this delay is not present before.
Fixes: cb33db2b6c ("media: i2c: IMX296 camera sensor driver")
Cc: stable@vger.kernel.org
Tested-by: Alexandru Ardelean <aardelean@baylibre.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX462 is the successor to IMX290, and wants very minor
changes to the register setup.
Add the relevant configuration to support it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewing the datasheets, register 0x3011 is meant to be 0x02 on imx327
and 0x00 on imx290.
Move it out of the common registers, and set it appropriately in the
sensor specific sections. (Included for imx290 to be explicit, rather
than relying on the default value).
Fixes: 2d41947ec2 ("media: i2c: imx290: Add support for imx327 variant")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The imx327 only supports up to 29.4dB of analogue gain, vs
the imx290 going up to 30dB. Both are in 0.3dB steps.
As we now have model specific config, fix this mismatch,
and delete the comment referencing it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ccs_data_parse() releases the allocated in-memory data structure when the
parser fails, but it does not clean up parsed metadata that is there to
help access the actual data. Do that, in order to return the data
structure in a sane state.
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The length field of the CCS static data blocks was mishandled, leading to
wrong interpretation of the length header for blocks that are 16 kiB in
size. Such large blocks are very, very rare and so this wasn't found
earlier.
As the length is used as part of input validation, the issue has no
security implications.
Fixes: a6b396f410 ("media: ccs: Add CCS static data parser library")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmcxMXceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1IgH/A3O7KIy/VR7D7O3
usbLqk1V+YWs/NsVdewEL/SYfXjCxqnejdk/AvN3ZAIxFeMHhAmcSCKno3zKgK9L
ML4kDrz22dPlA0XncNM8qKTCqAMgXTur1wafv3NAjutg0D3eHvAp0BW0GO5px93G
+kt3kOY32UaB+2Fl1GIub777pRi5U4u5AboQTu3x0TdRZJtV1pqgeddGoymNn6mi
xmMVbY3r5MXJQyHntoT9FIuxK3d+jGcgRHP5RWr53+vAUEFdlXiGcJV4dUXsuQNa
sEKJutCaUqQeiamjoo4bRZO7/2OAPX9Sv7sNIXD/irZZJmCcWr+GDCcUmL69Mjg7
7mx6XrM=
=HYUx
-----END PGP SIGNATURE-----
Merge tag 'v6.12-rc7' into __tmp-hansg-linux-tags_media_atomisp_6_13_1
Linux 6.12-rc7
* tag 'v6.12-rc7': (1909 commits)
Linux 6.12-rc7
filemap: Fix bounds checking in filemap_read()
i2c: designware: do not hold SCL low when I2C_DYNAMIC_TAR_UPDATE is not set
mailmap: add entry for Thorsten Blum
ocfs2: remove entry once instead of null-ptr-dereference in ocfs2_xa_remove()
signal: restore the override_rlimit logic
fs/proc: fix compile warning about variable 'vmcore_mmap_ops'
ucounts: fix counter leak in inc_rlimit_get_ucounts()
selftests: hugetlb_dio: check for initial conditions to skip in the start
mm: fix docs for the kernel parameter ``thp_anon=``
mm/damon/core: avoid overflow in damon_feed_loop_next_input()
mm/damon/core: handle zero schemes apply interval
mm/damon/core: handle zero {aggregation,ops_update} intervals
mm/mlock: set the correct prev on failure
objpool: fix to make percpu slot allocation more robust
mm/page_alloc: keep track of free highatomic
bcachefs: Fix UAF in __promote_alloc() error path
bcachefs: Change OPT_STR max to be 1 less than the size of choices array
bcachefs: btree_cache.freeable list fixes
bcachefs: check the invalid parameter for perf test
...
-----BEGIN PGP SIGNATURE-----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=SGfF
-----END PGP SIGNATURE-----
Merge tag 'media/v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- dvb-core fixes for vb2 check and device registration
- v4l2-core: fix an issue with error handling for VIDIOC_G_CTRL
- vb2 core: fix an issue with vb plane copy logic
- videobuf2-core: copy vb planes unconditionally
- vivid: fix buffer overwrite when using > 32 buffers
- vivid: fix a potential division by zero due to an issue at v4l2-tpg
- some spectre vulnerability fixes
- several OOM access fixes
- some buffer overflow fixes
* tag 'media/v6.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videobuf2-core: copy vb planes unconditionally
media: dvbdev: fix the logic when DVB_DYNAMIC_MINORS is not set
media: vivid: fix buffer overwrite when using > 32 buffers
media: pulse8-cec: fix data timestamp at pulse8_setup()
media: cec: extron-da-hd-4k-plus: don't use -1 as an error code
media: stb0899_algo: initialize cfr before using it
media: adv7604: prevent underflow condition when reporting colorspace
media: cx24116: prevent overflows on SNR calculus
media: ar0521: don't overflow when checking PLL values
media: s5p-jpeg: prevent buffer overflows
media: av7110: fix a spectre vulnerability
media: mgb4: protect driver against spectre
media: dvb_frontend: don't play tricks with underflow values
media: dvbdev: prevent the risk of out of memory access
media: v4l2-tpg: prevent the risk of a division by zero
media: v4l2-ctrls-api: fix error handling for v4l2_g_ctrl()
media: dvb-core: add missing buffer index check
According to adv7180.yaml, the correct property name is
"adi,force-bt656-4".
Expand the check to also test against the "adi,force-bt656-4" compatible
string.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The old hans.verkuil@cisco.com email address was discontinued years ago.
Replace it with the correct hansverk@cisco.com email.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Use runtime PM autosuspend function to avoid rapid power state bouncing.
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Switch from s_stream() to enable_streams() and disable_streams() pad
operations. They are preferred and required for streams support.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Port the ov5645 sensor driver to use the subdev active state.
Move all the format configuration to the subdevice state and simplify
the format handling, locking and initialization.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Remove the `power_lock` mutex used during control applications, as it is
only utilized in the .s_ctrl() function. Since the control framework
already serializes calls to this function, the mutex is unnecessary.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Utilize the v4l2_async_register_subdev_sensor() helper to register the
sub-device, as this facilitates parsing of firmware interfaces for remote
references.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Refactor error handling in the ov5645_probe() function by replacing
multiple dev_err() calls with dev_err_probe().
- Note that during this process, the error string "external clock
frequency %u is not supported" was replaced with "unsupported xclk
frequency %u" to ensure it wraps at 80 columns.
- Additionally, the error string for control initialization failure was
changed from "%s: control initialization error %d\n" to "failed to add
controls\n" as there is no need to print the function name and error code
in the string, since dev_err_probe() already provides this information.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
While assigning the subdev device pointer, use the local `dev` pointer
which is already extracted from the `i2c_client` pointer.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
2X.. mbus formats are related to parallel interface and
as such should not be acceptable on the sink pad of the bridge.
Only keep their csi counterpart in 1X..
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add handling of pm_runtime in order to control the supplies
and clocks of the bridge.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add pad enable_streams and disable_streams ops in addition to
v4l2_subdev_s_stream_helper. Moreover, use functions
v4l2_subdev_enable_streams and v4l2_subdev_disable_streams to
control the source subdev.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Following addition of cascaded s_stream call within
mipid02_stream_enable and mipid02_stream_disable,
the mipid02_stream_enable error handling must be fixed to simply
disable the clocks & data lanes without also calling
again the s_stream of the source subdev.
Moreover, main control registers are reset to 0 for all cases
of error within the mipid02_stream_enable even if they haven't yet
been written. Correct this behavior by simply returning an
error when register clear are not necessary.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Introduce enable_streams and disable_streams pad ops and
replace s_stream with the v4l2_subdev_s_stream_helper
function.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Add new structure 'mt9p031_model_info' to encapsulate format codes for
the mt9p031 camera sensor family. This approach enhances code clarity
and maintainability.
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The ACPI version of this driver "just works" on dts based systems with a
few extensions to facilitate.
- Add support for DT based probing
- Add support for taking the part out of reset via a GPIO reset pin
- Add in regulator bulk on/off logic for the power rails.
Once done this sensor works nicely on a Qualcomm X1E80100 CRD.
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The data-sheet and documentation for this part uses the name xvclk not
ext_clk for the input reference clock. Rename the variables and defines in
this driver to align with the data-sheet name.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
It is necessary to account for I2C quirks in the burst mode path of this
driver. Not all I2C controllers can accept arbitrarily long writes and this
is represented in the quirks field of the adapter structure.
Prior to this patch the following error message is seen on a Qualcomm
X1E80100 CRD.
[ 38.773524] i2c i2c-2: adapter quirk: msg too long (addr 0x0036, size 290, write)
[ 38.781454] ov08x40 2-0036: Failed regs transferred: -95
[ 38.787076] ov08x40 2-0036: ov08x40_start_streaming failed to set regs
Fix the error by breaking up the write sequence into the advertised maximum
write size of the quirks field if the quirks field is populated.
Fixes: 8f667d2023 ("media: ov08x40: Reduce start streaming time")
Cc: stable@vger.kernel.org # v6.9+
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # x1e80100-crd
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
It is not valid to call pm_runtime_set_suspended() and
pm_runtime_set_active() for devices with runtime PM enabled because it
returns -EAGAIN if it is enabled already and working. So, adjust the
order to fix it.
Cc: stable@vger.kernel.org
Fixes: 5f9a089b6d ("dw9768: Enable low-power probe on ACPI")
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
v4l2_subdev_init_finalize() already sets the HAS_EVENTS flag if a
control handler is set. Let's drop the HAS_EVENTS flag.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
v4l2_subdev_init_finalize() already sets the HAS_EVENTS flag if a
control handler is set, and subdev_do_ioctl() uses
v4l2_ctrl_subdev_subscribe_event() and v4l2_event_subdev_unsubscribe()
as defaults if the subdev doesn't have .(un)subscribe.
Let's drop the HAS_EVENTS flag and event handlers.
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Remove the direct dependency on OF by using the fwnode API. This makes
the driver usable on non-OF systems, such as ACPI-based platforms.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The mt9p031 driver doesn't support platform data anymore, and requires
the I2C device to be instantiated through a method that supports device
properties. As the driver lacks an ACPI device ID table, the device
matching will always go through the OF device ID table, either for OF
devices, or for ACPI devices using PRP0001. The I2C device ID table is
therefore not needed. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
No user of the mt9p031_platform_data legacy platform data for board
files exist in the kernel anymore. Drop support from the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tarang Raval <tarang.raval@siliconsignals.io>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
All ov2740_check_hwcfg() error-exit paths already log a detailed reason,
logging a second generic "failed to check HW configuration" error is
not useful, drop this.
The one exception is the -EPROBE_DEFER exit on
fwnode_graph_get_next_endpoint() returning NULL.
Call dev_err_probe() there to register the reason for deferring the probe,
this is used if the endpoint is still not there after 30 seconds, e.g. :
i2c-INT3474:00: deferred probe pending: waiting for fwnode graph endpoint
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
The v4l2_detect_cvt/gtf functions should check the result against the
timing capabilities: these functions calculate the timings, so if they
are out of bounds, they should be rejected.
To do this, add the struct v4l2_dv_timings_cap as argument to those
functions.
This required updates to the adv7604 and adv7842 drivers since the
prototype of these functions has now changed. The timings struct
that is passed to v4l2_detect_cvt/gtf in those two drivers is filled
with the timings detected by the hardware.
The vivid driver was also updated, but an additional check was added:
the width and height specified by VIDIOC_S_DV_TIMINGS has to match the
calculated result, otherwise something went wrong. Note that vivid
*emulates* hardware, so all the values passed to the v4l2_detect_cvt/gtf
functions came from the timings struct that was filled by userspace
and passed on to the driver via VIDIOC_S_DV_TIMINGS. So these fields
can contain random data. Both the constraints check via
struct v4l2_dv_timings_cap and the additional width/height check
ensure that the resulting timings are sane and not messed up by the
v4l2_detect_cvt/gtf calculations.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Fixes: 2576415846 ("[media] v4l2: move dv-timings related code to v4l2-dv-timings.c")
Cc: stable@vger.kernel.org
Reported-by: syzbot+a828133770f62293563e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/linux-media/000000000000013050062127830a@google.com/
Since commit 88785982a1 ("media: vb2: use lock if wait_prepare/finish
are NULL") it is no longer needed to set the wait_prepare/finish
vb2_ops callbacks as long as the lock field in vb2_queue is set.
Since the vb2_ops_wait_prepare/finish callbacks already rely on that field,
we can safely drop these callbacks.
This simplifies the code and this is a step towards the goal of deleting
these callbacks.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Currently, adv76xx_log_status() reads some date using
io_read() which may return negative values. The current logic
doesn't check such errors, causing colorspace to be reported
on a wrong way at adv76xx_log_status(), as reported by Coverity.
If I/O error happens there, print a different message, instead
of reporting bogus messages to userspace.
Fixes: 54450f591c ("[media] adv7604: driver for the Analog Devices ADV7604 video decoder")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
The PLL checks are comparing 64 bit integers with 32 bit
ones, as reported by Coverity. Depending on the values of
the variables, this may underflow.
Fix it ensuring that both sides of the expression are u64.
Fixes: 852b50aeed ("media: On Semi AR0521 sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
The function ub960_rxport_read is being called and afterwards ret is
being checked for any failures, however ret is not being assigned to
the return of the function call. Fix this by assigning ret to the
return of the call which appears to be missing.
Fixes: afe267f2d3 ("media: i2c: add DS90UB960 driver")
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If cci_read() fails, 'st' is set to 0 in cci_read(), so we return success,
instead of the expected error code.
Fix it and return the expected error.
Fixes: 9a6d7f2ba2 ("media: i2c: st-vgxy61: Convert to CCI register access helpers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently, the V4L2 subdevice is also created when the device is not
available/connected. From userspace perspective, there is no visible
difference between a working and not-working subdevice (except when
trying it out).
This commit adds a simple preparation step, which includes an
availability check, before the subdev is initialized.
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As we don't know the mode during probe(), it doesn't make sense to
update the sensors' registers with assumptions. As imx290_set_ctrl(),
which is responsible for the happening communication, already ensures that
there is no communication with a suspended sensor, put the sensor to
suspend before calling it.
To clarify the dependency of the PM runtime to the link of the subdev
and the imx290 instance, put the block together.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This register is not described in the public available imx290 datasheet.
Additionally, a read returns '0x07d0' for an imx327lqr and also for an
imx462, which means it cannot be used to distinguish between those two
imx290 derivatives.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Benjamin Bara <benjamin.bara@skidata.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This commit corrects spelling errors in comments within
the media/i2c directory found by codespell to enhance clarity
and maintainability of the code.
This change does not affect the functionality.
Signed-off-by: Yu Jiaoliang <yujiaoliang@vivo.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Controls can be exposed to userspace via a v4l-subdevX device, and
userspace has to be able to subscribe to control events so that it is
notified when the control changes value.
Add missing HAS_EVENTS support: flag and .(un)subscribe_event().
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Controls can be exposed to userspace via a v4l-subdevX device, and
userspace has to be able to subscribe to control events so that it is
notified when the control changes value.
Add missing HAS_EVENTS support: flag and .(un)subscribe_event().
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The vb2_queue_init() will expect the vb2_queue lock pointer to be set in
the future. So for those drivers that set the lock later, move it up to
before the vb2_queue_init() call.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Matt Ranostay <matt@ranostay.sg>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
André Apitzsch
Sakari Ailus
Hans de Goede
Linus Torvalds
Thomas Weißschuh
Sam Bobrowicz
Tomi Valkeinen
Mehdi Djait
Dave Stevenson
Naushir Patuck
Luca Weiss
Peter Zijlstra
Mauro Carvalho Chehab
Fabio Estevam
Hans Verkuil
Zhi Mao
Lad Prabhakar
Alain Volmat
Tarang Raval
Bryan O'Donoghue
Jinjie Ruan
Tommaso Merciai
Laurent Pinchart
Colin Ian King
Christophe JAILLET
Benjamin Bara
Yu Jiaoliang
Dan Carpenter
Alexander Shiyan
Hans Verkuil