While updating the source OUI on the sink the driver should avoid
writing the OUI if it's already up-to-date to prevent the sink from
resetting itself in response to the update. On eDP - the only output
type where the OUI was updated so far - the driver ensured this by
comparing the current source OUI DPCD register values with the expected
Intel OUI value, skipping the update in case of a match. On some non-eDP
sinks - at least on Synaptics branch devices - this method doesn't work,
since the source OUI DPCD registers read back as all 0, even after
updating the registers.
Handle the above kind of sinks by tracking when the OUI was updated and
so should be valid, regardless of what the DPCD registers contain.
eDP sinks reset the written source OUI value when the panel power is
disabled, invalidate the OUI state accordingly.
This is required by a follow-up patch updating the source OUI for
non-eDP sink types as well.
v2: Fix setting intel_dp::oui_valid=true, if the DPCD register contains
already the expected value.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-5-imre.deak@intel.com
If the source OUI DPCD register value matches the expected Intel OUI
value, the write timestamp doesn't get updated leaving it at the 0
initial value if the OUI wasn't written before. This can lead to an
incorrect wait duration in intel_dp_wait_source_oui(), since jiffies is
not inited to 0 in general (on a 32 bit system INITIAL_JIFFIES is set to
5 minutes ahead of wrap-around). Fix this by intializing the write
timestamp in the above case as well.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-4-imre.deak@intel.com
The sink's capabilities, like the DSC caps, depend on the source OUI
written to the sink's DPCD registers and so this OUI value should be
valid for the whole duration of the detection. An eDP sink will reset
this OUI value when the panel power is disabled, so prevent the
disabling - happening by default after a 1 sec idle period - for the
whole duration of detection.
v2: Update the documentation for intel_pps_on(). (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-3-imre.deak@intel.com
Make sure that a DP connector detection doesn't happen in parallel
with an ongoing modeset on the connector. The reasons for this are:
- Besides reading the capabilities, EDID etc. the detection may change
the state of the sink (via the AUX bus), for instance by setting the
LTTPR mode or the source OUI (the latter introduced by an upcoming
patch). It's better to avoid such changes affecting an onging modeset
in any way.
- During a modeset's link training any access to DPCD registers, besides
the registers used for link training should be avoided, at least in
the LTTPR non-transparent and transparent link training modes.
Such asynchronous accesses - besides connector detection - can also
happen via the AUX device node for instance, for those a parallel
modeset will have to be avoided in a similar way to the change in this
patch. (A topic for a follow-up change.)
- The source OUI written to an eDP sink is valid only while the panel
power is enabled. A modeset on eDP will enable/disable the panel power
synchronously; this should be prevented in the middle of the connector
detection, to ensure a consistent sink state (which depends on the
source OUI) for the whole duration of detection. The panel power could
still get disabled during detection after an idle period (1 sec), this
will be prevented by the next patch.
v2: (Ville)
- s/wait_for_crtc_hw_done/wait_for_connector_hw_done
- Get drm_device using an intel_display instead of drm_i915_private ptr.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241025160259.3088727-2-imre.deak@intel.com
Use x100, or ver * 100 + rel, versions for full IP version checks,
similar to what xe driver does:
- Replace IP_VER(14, 1) inline with 1401, etc.
- Convert DISPLAY_VER_FULL() to DISPLAY_VERx100()
- Convert IS_DISPLAY_VER_FULL() to IS_DISPLAY_VERx100()
- Convert IS_DISPLAY_VER_STEP() to IS_DISPLAY_VERx100_STEP()
This makes ver.rel versions easier to use, follows the xe driver
pattern, and drops the dependency on the IP_VER() macro.
v2: Rebase, drop IP_VER() from xe compat headers
v3: Rebase
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029155536.753413-1-jani.nikula@intel.com
Some devices NAK DPCD writes to the SOURCE OUI (0x300) DPCD registers.
Reduce the log level priority to prevent dmesg noise for these devices.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Sai Teja Pottumuttu <sai.teja.pottumuttu@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241004210816.3976058-1-clinton.a.taylor@intel.com
Read PICA register to see if edp over type C is possible and then
add the appropriate tables for it.
--v2
-remove bool from intel_encoder have it in runtime_info [Jani]
-initialize the bool in runtime_info init [Jani]
-dont abbreviate the bool [Jani]
--v3
-Remove useless display version check [Jani]
-change the warn on condition [Jani]
-no need for a different function for edp type c check [Jani]
-dont add register in i915_reg [Jani]
Bspec: 68846
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241028193015.3241858-3-clinton.a.taylor@intel.com
The function parse_lfp_panel_dtd() is called when the driver
attempts to initialize the eDP connector, and it allocates memory,
which is recorded in panel->vbt.lfp_vbt_mode. However, since no
eDP panel is connected, the driver fails at intel_edp_init_dpcd()
and follows the failure path. Unfortunately, the allocated memory
is not freed in this case.
To fix this issue, free the memory in the failure path.
leak info from kmemleak:
"
unreferenced object 0xffff8881252f8800 (size 128):
comm "systemd-udevd", pid 192, jiffies 4294896880
hex dump (first 32 bytes):
e8 fd 00 00 00 04 18 04 a0 04 40 05 00 00 00 03 ..........@.....
03 03 09 03 26 03 00 00 0a 00 00 00 00 00 00 00 ....&...........
backtrace (crc 7448f6b4):
[<ffffffff82475c9b>] kmemleak_alloc+0x4b/0x80
[<ffffffff814bb50e>] __kmalloc_cache_noprof+0x2be/0x390
[<ffffffffa069862c>] intel_bios_init_panel+0x1c4c/0x2720 [xe]
[<ffffffffa0699123>] intel_bios_init_panel_early+0x13/0x20 [xe]
[<ffffffffa06fceb9>] intel_dp_init_connector+0x2f9/0x1080 [xe]
[<ffffffffa06c370a>] intel_ddi_init+0xbba/0xf50 [xe]
[<ffffffffa069b906>] intel_bios_for_each_encoder+0x36/0x60 [xe]
[<ffffffffa06d7bd6>] intel_setup_outputs+0x206/0x450 [xe]
[<ffffffffa06dad33>] intel_display_driver_probe_nogem+0x163/0x1f0 [xe]
[<ffffffffa0680fc7>] xe_display_init_noaccel+0x27/0x70 [xe]
[<ffffffffa05b30d6>] xe_device_probe+0x806/0x9a0 [xe]
[<ffffffffa0612f0f>] xe_pci_probe+0x31f/0x590 [xe]
[<ffffffff81b41718>] local_pci_probe+0x48/0xb0
[<ffffffff81b432c8>] pci_device_probe+0xc8/0x280
[<ffffffff81d5dde8>] really_probe+0xf8/0x390
[<ffffffff81d5e11a>] __driver_probe_device+0x8a/0x170
"
v2 (Jani):
-use intel_bios_fini_panel() to pair with intel_bios_init_panel_early()
Signed-off-by: Shuicheng Lin <shuicheng.lin@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241016150154.1466131-1-shuicheng.lin@intel.com
A registered eDP connector is considered to be always connected, so it's
unnecessary to poll it for a connect/disconnect event. Polling it
involves AUX accesses toggling the panel power, which in turn can
generate a spurious short HPD pulse and possibly a new poll cycle via
the short HPD handler runtime resuming the device. Avoid this by
disabling the polling for eDP connectors.
This avoids IGT tests timing out while waiting for the device to runtime
suspend, the timeout caused by the above runtime resume->poll->suspend->
resume cycle keeping the device in the resumed state.
Testcase: igt/kms_pm_rpm/unverisal-planes
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241009194358.1321200-3-imre.deak@intel.com
If the device is runtime suspended the eDP panel power is also off.
Ignore a short HPD on eDP if the device is suspended accordingly,
instead of checking the panel power state via the PPS registers for the
same purpose. The latter involves runtime resuming the device
unnecessarily, in a frequent scenario where the panel generates a
spurious short HPD after disabling the panel power and the device is
runtime suspended.
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241009194358.1321200-2-imre.deak@intel.com
Implement required changes for mode validation and compute config,
to support Ultrajoiner.
v2:
-Drop changes for HDMI.
-Separate out DSC changes into another patch.
v3: Fix check in can_ultrajoiner. (Ankit)
v4:
-Unify helper to check joiner requirement. (Ville)
-Split patches for ultrajoiner changes for max dsc slices and compressed
bpp.(Ankit)
v5: Fix check for joiner. (Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-12-ankit.k.nautiyal@intel.com
When bigjoiner is used, we need at least 2 dsc slices per pipe.
Modify the condition in intel_dp_dsc_get_slice_count() to reflect the
same.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-11-ankit.k.nautiyal@intel.com
Add compressed bpp limitations for ultrajoiner.
v2: Fix the case for 1 pipe. (Ankit)
v3: Refactor existing helper separately and add only ultrajoiner
limitation. (Ville)
v4: Separate out function for ultrajoiner_ram_bits.
v5: Make the helper function more concise. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-10-ankit.k.nautiyal@intel.com
Streamline the helper to get max compressed bpp for bigjoiner case, to
effectively use num of pipes joined. This will make the addition of
ultrajoiner limitations easier and improve redability.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-9-ankit.k.nautiyal@intel.com
Currently compressed max_bpp limitations for small joiner ram, big joiner
etc are intermingled. Seprate these limitations into separate functions.
v2: Use num_joined_pipes in small joiner ram helper and other minor
fixes. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240930163549.416410-8-ankit.k.nautiyal@intel.com
Add a helper to compute the number of pipes required.
This will depend on whether the joiner is required or is forced through
the debugfs. If no joiner is required the helper returns 1.
v2:
-Return 1 if no joiner is required. (Ville)
-Change the suffix from joined_pipes to num_pipes. (Ville)
-Use number of pipes while calculating joined_pipe masks and
max_dotclk. (Ville)
v3: Simplify and rename the helper to intel_dp_num_joined_pipes(). Ville
v4: Remove redundant 'fallthrough' statement. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926134322.3728021-5-ankit.k.nautiyal@intel.com
At the moment, the debugfs for joiner allows only to force enable/disable
pipe joiner for 2 pipes. Modify it to force join 'n' number of pipes,
where n is a valid pipe joiner configuration.
This will help in case of ultra joiner where 4 pipes are joined.
v2:
-Fix commit message to state that only valid joiner config can be
forced. (Suraj)
-Rename the identifiers to have INTEL_BIG/NONE_JOINER_PIPES. (Suraj)
v3:
-Avoid enum for joiner pipe counts, use bare numbers for better
readability. (Ville)
-Remove redundant prints from debugfs. (Ville)
v4: Return -EINVAL if joiner forced to an invalid value.
v5: Remove extra debug message. (Ville)
v6: Minor fix in switch case. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926134322.3728021-4-ankit.k.nautiyal@intel.com
intel_dp_init_connector() is no place for detecting stuff via
DPCD (except perhaps for eDP). Move the colorimetry stuff into
a more appropriate place.
Cc: Jouni Högander <jouni.hogander@intel.com>
Fixes: 00076671a6 ("drm/i915/display: Move colorimetry_support from intel_psr to intel_dp")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240918190441.29071-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
In preparation of ultrajoiner, use number of joined pipes in the dsc
helpers to compute dsc slices and max compressed bpp, instead of using
the joiner flag.
v2: Adjust the formulae to use num of pipes as 1 (no joiner) or 2
(bigjoiner). (Ankit)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240916102836.2149012-5-ankit.k.nautiyal@intel.com
In preparation of ultrajoiner, use number of pipes in the
intel_mode_valid_max_plane_size helper, instead of joiner flag.
v2: Use num_joined_pipes 1 where there are no joined pipes (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240916102836.2149012-4-ankit.k.nautiyal@intel.com
In preparation of ultrajoiner, use number of joined pipes in the
intel_dp_joiner_needs_dsc helper, instead of joiner flag.
v2: Use intel_crtc_num_joined_pipes. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240916102836.2149012-3-ankit.k.nautiyal@intel.com
Add macros to check if platform supports bigjoiner/uncompressed joiner.
Replace the existing DISPLAY_VER checks with these.
Additionally use it before readout for joiner stuff, where its missing.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240912132931.1320686-1-ankit.k.nautiyal@intel.com
In case of UHBR rates, we do not need to explicitly enable FEC by writing
to DP_TP_CTL register.
For MST use-cases, intel_dp_mst_find_vcpi_slots_for_bpp() takes care of
setting fec_enable to false. However, it gets overwritten in
intel_dp_dsc_compute_config(). This change keeps fec_enable false across
MST and SST use-cases for UHBR rates.
While at it, add a comment explaining why we don't enable FEC in eDP v1.5.
v2: Correct logic to cater to SST use-cases (Jani)
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240822061448.4085693-1-chaitanya.kumar.borah@intel.com
UHBR20 is not supported by battlemage and the maximum link rate
supported is UHBR13.5
v2: Replace IS_DGFX with IS_BATTLEMAGE (Jani)
HSD: 16023263677
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Fixes: 98b1c87a5e ("drm/i915/xe2hpd: Set maximum DP rate to UHBR13.5")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240827081205.136569-1-arun.r.murthy@intel.com
Currently there is no way to apply quirk on device only if certain panel
model is installed. This patch implements such mechanism by adding new
quirk type intel_dpcd_quirk which contains also sink_oui and sink_device_id
fields and using also them to figure out if applying quirk is needed.
New intel_init_dpcd_quirks is added and called after drm_dp_read_desc with
proper sink device identity read from dpcdc.
v3:
- !mem_is_zero fixed to mem_is_zero
v2:
- instead of using struct intel_quirk add new struct intel_dpcd_quirk
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240902064241.1020965-2-jouni.hogander@intel.com
Need to take some Xe bo definition in here before
we can add the BMG display 64k aligned size restrictions.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
In some cases the sink can reset itself after it was configured into MST
mode, without the driver noticing the disconnected state. For instance
the reset may happen in the middle of a modeset, or the (long) HPD pulse
generated may be not long enough for the encoder detect handler to
observe the HPD's deasserted state. In this case the sink's DPCD
register programmed to enable MST will be reset, while the driver still
assumes MST is still enabled. Detect this condition, which will tear
down and recreate/re-enable the MST topology.
v2:
- Add a code comment about adjusting the expected DP_MSTM_CTRL register
value for SST + SideBand. (Suraj, Jani)
- Print a debug message about detecting the link reset. (Jani)
- Verify the DPCD MST state only if it wasn't already determined that
the sink is disconnected.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11195
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240823162918.1211875-1-imre.deak@intel.com
Replace the BPP_X16_FMT()/ARGS() helpers defined by the driver with the
equivalent FXP_Q4_FMT()/ARGS() helpers defined by DRM core.
v2: Rebase on the s/DRM_X16/FXP_Q4 change.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240805150802.3568970-6-imre.deak@intel.com
Replace the to_bpp_int_roundup() helper defined by the driver with the
equivalent fxp_q4_to_int_roundup() helper defined by DRM core.
v2: Rebase on s/drm_x16/fxp_q4 change.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240805150802.3568970-4-imre.deak@intel.com
As explained in the previous patch, the MST link BW reported by branch
devices during topology probing/path resources enumeration depends on
the link parameters programmed to DPCD to be up-to-date. After a sink is
plugged this is not ensured, as those DPCD values start out zeroed. The
target link parameters (for a subsequent modeset) are the maximum that
is supported, so make sure these maximum values are programmed before the
topology probing.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-14-imre.deak@intel.com
The MST link BW reported by branch devices via the ENUM_PATH_RESOURCES
message depends on the channel coding and link rate/lane count
parameters programmed to DPCD. This is the case at least for some branch
devices, while for others the reported BW is independent of the link
parameters. In any case the DP standard requires the branch device to
adjust the returned value to both account for the different way the BW
for FEC is accounted for (included in the returned value for non-UHBR
and not included for UHBR rates) and to limit the returned value to the
(trained) link BW between the source and first downstream branch
device, see DP v2.0/v2.1 Figure 2-94, DP v2.1 5.9.7. Presumedly this is
also the reason why the standard requires the DPCD link rate/lane count
values being up-to-date before sending the ENUM_PATH_RESOURCES message,
see DP v2.1 2.14.9.4.
Based on the above reprobe the MST topology after the link is retrained
with new link parameters to make sure that the MST link BW tracked in
the MST topology state (via each topology port's full_pbn value) is
up-to-date.
The next patch will make sure that the MST link BW is also kept
up-to-date if the link is disabled.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-13-imre.deak@intel.com
The MST topology probing depends on the maximum link parameters -
programmed to DPCD if required by a follow-up patch - so make sure these
parameters are up-to-date before configuring and probing the MST
topology.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-11-imre.deak@intel.com
On MST links - at least for some MST branch devices - the list of modes
returned to users on an enabled link depends on the current link
rate/lane count parameters (besides the DPRX link capabilities, any MST
branch BW limit and the maximum link parameters reduced after LT
failures). In particular the MST branch BW limit may depend on the link
rate/lane count parameters programmed to DPCD. After an LT failure and
limiting the maximum link parameters accordingly, users should see a
mode list reflecting these new limits. However with the current fallback
order this isn't ensured, as the new limit could allow for modes
requiring a higher link BW, but these modes will be filtered out due to
the enabled link's lower link BW.
Ensure that the mode list changes in a consistent way after a link
training failure and reducing the link parameters by changing the
fallback order on MST links to happen in BW order.
v2:
- s/INTEL_DP_MAX_SUPPORTED_LANE_COUNTS/INTEL_DP_MAX_SUPPORTED_LANE_CONFIGS
and s/num_common_lane_counts/num_common_lane_configs to make the
difference wrt. max lane counts clearer. (Suraj)
- Add a TODO comment to make the SST fallback logic work the same way as
MST. (Arun)
- Use sort_r()'s default swap function instead of a custom one.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729144458.2763667-1-imre.deak@intel.com
There are multiple failure cases a modeset-retry uevent can be sent for
a link (TBT tunnel BW allocation failure, unrecoverable link training
failure), a follow-up patch adding the handling for a new case where the
DP MST payload allocation fails. The uevent is the same in all cases,
sent to all the connectors on the link, so in case of multiple failures
there is no point in sending a separate uevent for each failure; prevent
this, sending only a single modeset-retry uevent for a commit.
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-7-imre.deak@intel.com
Initialize the DP link parameters during HW readout. These need to be
up-to-date at least for the MST topology probing, which depends on the
link rate and lane count programmed in DPCD. A follow-up patch will
program the DPCD values to reflect the maximum link parameters before
the first MST topology probing, but should do so only if the link is
disabled (link_trained==false).
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722165503.2084999-6-imre.deak@intel.com
AS SDP should be computed when VRR timing generator is also enabled.
Correct the compute condition to compute params of Adaptive sync SDP
when VRR timing genrator is enabled along with sink support indication.
--v2:
Modify if condition (Jani).
Fixes: b2013783c4 ("drm/i915/display: Cache adpative sync caps to use it later")
Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: intel-xe@lists.freedesktop.org
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
(added prefix drm in subject)
Link: https://patchwork.freedesktop.org/patch/msgid/20240730040941.396862-1-mitulkumar.ajitkumar.golani@intel.com
Clear VSC SDP if intel_dp_set_infoframes is called from post ddi disable
routine i.e with the variable of enable as false. This is to avoid
an infoframes.enable mismatch issue which is caused when pipe is
connected to eDp which has psr then connected to DPMST. In this case
eDp's post ddi disable routine does not clear infoframes.enable VSC
for the given pipe and DPMST does not recompute VSC SDP and write
infoframes.enable which causes a mismatch.
--v2
-Make the comment match the code [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240724163743.3668407-1-suraj.kandpal@intel.com
After a bad link state is detected, the sink capabilities with which the
link was originally trained could have changed: for instance another
sink got connected or the retraining was forced after the rate/lane count
got decreased (as a fallback). In these cases the retraining modeset
fails as expected also printing a debug message, so don't WARN on it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240712135724.660399-3-imre.deak@intel.com
After the previous patch link training happens always with a valid
atomic state, so remove the NOTE comments and asserts which required a
valid state only for DP-MST and allowed for a NULL state for DP-SST.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240712135724.660399-2-imre.deak@intel.com
Instead of direct calls of the link training functions, use a modeset
commit to retrain a DP link in SST mode, similarly to how this is done
in DP-MST mode. Originally the current way was chosen presumedly,
because there wasn't a well-established way in place for the driver to
do an internal (vs. userspace/kernel client) commit. Since then such
internal commits became a common place (initial-, HDMI/TC link reset
commit), so there is no reason to handle the DP-SST link-retraining case
differently.
At the end of the current sequence the HW reported a FIFO underrun -
without other issues visible to users - because during retraining the
link's encoder/port was disabled/re-enabled without also
disabling/re-enabling the corresponding pipe/transcoder (as required by
the spec); the corresponding underrun error message was suppressed as a
known issue. Based on Ankit's test on DG2 the underrun error was still
reported as it got detected with some (vblank) delay wrt. other
platforms. Switching to a modeset commit resolves these underrun related
issues.
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240712135724.660399-1-imre.deak@intel.com
Regularly retraining a link during an atomic commit happens with the
given pipe/link already disabled and hence intel_dp->link_trained being
false. Ensure this also for retraining a DP SST link via direct calls to
the link training functions (vs. an actual commit as for DP MST). So far
nothing depended on this, however the next patch will depend on
link_trained==false for changing the LTTPR mode to non-transparent.
Cc: <stable@vger.kernel.org> # v5.15+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-2-imre.deak@intel.com
(cherry picked from commit a4d5ce6176)
Signed-off-by: Tvrtko Ursulin <tursulin@ursulin.net>
Regularly retraining a link during an atomic commit happens with the
given pipe/link already disabled and hence intel_dp->link_trained being
false. Ensure this also for retraining a DP SST link via direct calls to
the link training functions (vs. an actual commit as for DP MST). So far
nothing depended on this, however the next patch will depend on
link_trained==false for changing the LTTPR mode to non-transparent.
Cc: <stable@vger.kernel.org> # v5.15+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-2-imre.deak@intel.com
Add new member to struct intel_dp to cache support of Adaptive Sync
SDP capabilities and use it whenever required to avoid HW access
to read capability during each atomic commit.
-v2:
- Squash both the patches
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240704082638.2302092-2-mitulkumar.ajitkumar.golani@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reuse intel_dp_has_dsc() during .compute_config() instead of
repeating some of the checks again by hand. We'll be adding
more checks to intel_dp_has_dsc() and this will make sure
we cover both .mode_valid() and .compute_config() with them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240517145356.26103-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Extract a helper to check whether the source+sink combo
supports DSC. That basic check is needed both during mode
validation and compute config. We'll also need to add extra
checks to both places, so having a single place for it is nicer.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240517145356.26103-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add a connector debugfs entry to force retrain an active link. This can
be used to test both custom link parameters (previously forced via the
force_link_rate/lane_count entries) or link train failure scenarios
(previously forced via the force_link_training_failure entry). The entry
will autoreset after the link-retrain is complete.
v2: Add the entry from intel_dp_link_training.c (Jani)
v3: Lock connection_mutex only for the required intel_dp state. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-21-imre.deak@intel.com
Add connector debugfs entries to force the link rate/lane count to be
used by a link training afterwards. These settings will be clamped to
the supported, i.e. the source's and sink's common rate/lane count.
After forcing the link rate/lane count reset the link training
parameters and for a non-auto setting disable reducing the link
parameters via the fallback logic. The former one can be used after
testing link training failure scenarios - via debugfs entries added
later - to reset the reduced link parameters after the test.
v2:
- Add the entries from intel_dp_link_training.c (Jani)
- Rename the entries to i915_dp_set_link_rate/lane_count.
v3: (Ville)
- Rename the entries/struct fields to force_link_rate/lane_count.
- Lock connection_mutex only for the required intel_dp state.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-18-imre.deak@intel.com
Reduce the link parameters after a link training failure for MST
outputs, similarly to how this is done for SST.
For now allow the reduction only by staying in the 8b/10b vs. 128b/132b
mode. Enabling the mode switch is left for a follow-up patchset, after
taking measures ensuring that the mode switch happens properly. In
particular a rediscovery of the whole MST topology may be required for
such a switch, see the References below.
Link: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/10970
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-17-imre.deak@intel.com
After a link training failure if the link parameters can't be further
reduced, there is no point in trying to retrain the link in the driver.
This avoids excessive retrain attempts after detecting a bad link, for
instance while handling MST HPD IRQs, which is likely redundant as the
link training failed already twice with the same minimum link
parameters. Userspace can still try to retrain the link with these
parameters via a modeset.
While at it make the error message more accurate.
v2: Move converting the error to a debug message to the relevant
follow-up patch. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-15-imre.deak@intel.com
Simplify things by retraining a DP link if a bad link is detected in the
HPD IRQ handler from the encoder's check link state work, similarly to
how this is done after a modeset link training failure.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-14-imre.deak@intel.com
Simplify things by retraining a DP link if a bad link is detected in the
connector detect handler from the encoder's check link state work,
similarly to how this is done after a modeset link training failure.
v2: Add TODO: comment to remove the detect-time link state check.
(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-13-imre.deak@intel.com
Simplify things by retraining a DP link if a bad link is detected in the
hotplug handler from the encoder's check link state work, similarly to
how this is done after a modeset link training failure.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-12-imre.deak@intel.com
Send a modeset-retry uevent to all connectors in the same MST topology
after a link training failure and reduction of the link parameters. This
matches the way the same uevent is sent after a DP tunnel BW allocation
failure.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-11-imre.deak@intel.com
The next patch adds sending a modeset-retry uevent after a link training
failure to all MST connectors on link. This requires the atomic state,
so pass it to intel_dp_start_link_train(). In case of SST where
retraining still happens by calling this function directly instead of a
modeset commit the atomic state is not available and NULL is passed
instead. This is ok, since in this case the encoder's only DP connector
is available from intel_dp->attached_connector not requiring the atomic
state.
v2: Add NOTE that the atomic state may not be valid for SST links and
assert that it's valid for MST links. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-10-imre.deak@intel.com
Try to maintain the current link parameters by retrying the link
training with unchanged link parameters before reducing these parameters
(sending an uevent to userspace to retrain the link instead).
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-9-imre.deak@intel.com
Recheck the link state after a passing link training, with a 2 sec delay
to account for cases where the link goes bad following the link training
and the sink doesn't report this via an HPD IRQ.
The delayed work added here will be also used by a later patch after a
failed link training to try to retrain the link with unchanged link
params before reducing the link params.
v2: Don't flush an uninitialized delayed work (on HDMI-only DDI ports).
v3:
- Move the helpers to a new intel_encoder.c file, rename them
accordingly. (Ville)
- Add the work to intel_encoder instead of intel_digital_port.
- Call the encoder specific link check function via an encoder hook.
- Flush the link check work during encoder destroy from
intel_dp_encoder_flush_work().
- Flush the link check work during encoder suspend as well.
v4: Call intel_encoder_link_check_init() with a valid encoder pointer.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610181428.2955658-1-imre.deak@intel.com
Instead of direct calls to the link train functions, retrain the link
via a commit modeset. The direct call means that the output port will be
disabled/re-enabled while the rest of the pipeline (transcoder) is
active, which doesn't seem to work on MST at least. It leads to
underruns and black screen, presumedly because the transcoder is not
disabled/re-enabled along the port.
Leave switching to a commit modeset on SST for a later patchset, as that
seems to work ok currently (though better to using a commit there too,
due to the suppressed underruns).
v2: Keep reverse line length order for local variables. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-7-imre.deak@intel.com
Move the functions used to reduce the link parameters during link
training to intel_dp_link_training.c .
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-4-imre.deak@intel.com
For clarity move the link training parameters updated during link
training based on the pass/fail LT result under a substruct in intel_dp.
This prepares for later patches in this patchset adding similar params
here. Rename intel_dp_reset_max_link_params() to
intel_dp_reset_link_params() to better reflect what state gets reset.
v2: Add the parameters to a more generic link substruct. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-3-imre.deak@intel.com
Lets unify both bigjoiner and ultrajoiner under simple "joiner" name,
because in future we might have multiple configurations, involving
multiple bigjoiners, ultrajoiner, however it is possible to use
same api for handling both.
v2: - Renamed back some bigjoiner specific parts for now(Ville)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
[vsyrjala: Catch a few more cases]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240607075457.15700-1-stanislav.lisovskiy@intel.com
Compute params for Adaptive Sync SDP when Fixed Average Vtotal
mode is enabled.
--v2:
Since vrr.enable is set in case of cmrr also, handle accordingly(Ankit).
--v3:
- Since vrr.enable is set in case of cmrr also, handle
accordingly(Ankit).
- check cmrr.enable when CMRR flags are set during intel_dp_compute_as_sdp.
--v4:
- Use drm_mode_vrefresh instead of manual calculation (Ankit).
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-8-mitulkumar.ajitkumar.golani@intel.com
Add support of pack and unpack for target_rr_divider.
--v2:
- Set Target Refresh Rate Divider bit when related
AS SDP bit is set (Ankit).
--v3:
- target_rr_divider is bools so set accordingly (Ankit).
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610072203.24956-7-mitulkumar.ajitkumar.golani@intel.com
Link Off Between Active Frames, is a new feature for eDP
that allows the panel to go to lower power state after
transmission of data. This is a feature on top of ALPM, AS SDP.
Add compute config during atomic-check phase.
v1: RFC version.
v2: Add separate flag for auxless-alpm. [Jani]
v3:
- intel_dp->lobf_supported replaced with crtc_state->has_lobf. [Jouni]
- Add DISPLAY_VER() check. [Jouni]
- Modify function name of get_aux_less_status. [Jani]
v4: Add enum alpm_mode to hold the aux-wake/less capability.
v5: Add alpm_dpcd to intel_dp and use aux_wake_supported()/
aux_less_wake_supported() instead of enum alpm_mode. [Jouni]
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240529200742.1694401-5-animesh.manna@intel.com
Add new boolean to store panel replay selective update support of sink into
intel_psr struct. Detect panel replay selective update support and store
it into this new boolean.
v3: Clear sink_panel_replay_su_support in intel_dp_detect
v2: Merge adding new boolean into this patch
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240510093823.3146455-7-jouni.hogander@intel.com
We are about to enable Panel Replay Selective update mode. Vsc revision 0x6
for Panel Replay no matter if it is selective update or full frame update
mode. Take this into account when preparing VSC SDP package.
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240510093823.3146455-4-jouni.hogander@intel.com
We are going to reuse has_psr2 for panel_replay as well. Rename it
as has_sel_update to avoid confusion.
v3: do not add has_psr check into psr2 case in intel_dp_compute_vsc_sdp
v2: Rebase
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240510093823.3146455-2-jouni.hogander@intel.com
Make has_gamut_metadata_dip() non static so it can also be used to
at other places eg in intel_dp_aux_backlight. So that we can check
if HW is capable of sending SDP which helps us decide if we use
AUX based HDR control or via SDP.
--v2
-State reason the function is needed [Arun]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240507040407.1056061-2-suraj.kandpal@intel.com
Factor out a function to check for 128b/132b channel coding support used
by a follow-up patch in the patchset.
v2: s/drm_dp_uhbr_channel_coding_supported()/drm_dp128b132b_supported()
(Jani)
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240417141936.457796-1-imre.deak@intel.com
Fix the calculation of the DSC line buffer depth. This is limited both
by the source's and sink's maximum line buffer depth, but the former one
was not taken into account. On all Intel platform's the source's maximum
buffer depth is 13, so the overall limit is simply the minimum of the
source/sink's limit, regardless of the DSC version.
This leaves the DSI DSC line buffer depth calculation as-is, trusting
VBT.
On DSC version 1.2 for sinks reporting a maximum line buffer depth of 16
the line buffer depth was incorrectly programmed as 0, leading to a
corruption in color gradients / lines on the decompressed screen image.
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Manasi Navare <navaremanasi@chromium.org>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240416221010.376865-2-imre.deak@intel.com
Pass the connector explicitly to intel_dp_need_bigjoiner()
so that it'll actually check the correct place for the
bigjoiner force flag.
Tested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404213441.17637-11-ville.syrjala@linux.intel.com
All joined pipes share the same transcoder/timing generator.
Currently we just do the commits per-pipe, which doesn't really
work if we need to change the timings at the same time. For
now just disable live M/N updates when bigjoiner is needed.
Cc: stable@vger.kernel.org
Tested-by: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240404213441.17637-5-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Add necessary function definitions to compute AS SDP data.
The new intel_dp_compute_as_sdp function computes AS SDP
values based on the display configuration, ensuring proper
handling of Variable Refresh Rate (VRR).
--v2:
- Added DP_SDP_ADAPTIVE_SYNC to infoframe_type_to_idx(). [Ankit]
- Separated patch for intel_read/write_dp_sdp. [Ankit]
- _HSW_VIDEO_DIP_ASYNC_DATA_A should be from ADL onward. [Ankit]
- Fixed indentation issues. [Ankit]
--v3:
- Added VIDEO_DIP_ENABLE_AS_HSW flag to intel_dp_set_infoframes.
--v4:
- Added HAS_VRR check before writing AS SDP.
--v5:
Added missed HAS_VRR check before reading AS SDP.
--v6:
- Used Adaptive Sync sink status as a check for read/write SDP. (Ankit)
--v7:
- Remove as_sdp_enable from crtc_state.
- Add a comment mentioning current support of
DP_AS_SDP_AVT_FIXED_VTOTAL.
- Add state checker for AS_SDP infoframe enable.
--v8:
- Drop conn_state from intel_dp_compute_as_sdp, as not used.
- Remove fullstop in subject line.
--v9:
- Add vrr.enable instead of is_in_vrr_range.
--v10:
- remove vrefresh and connector, as they are no longer required.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-7-mitulkumar.ajitkumar.golani@intel.com
Add the necessary structures and functions to handle reading and
unpacking Adaptive Sync Secondary Data Packets. Also add support
to write and pack AS SDP.
--v2:
- Correct use of REG_BIT and REG_GENMASK. [Jani]
- Use as_sdp instead of async. [Jani]
- Remove unrelated comments and changes. [Jani]
- Correct code indent. [Jani]
--v3:
- Update definition names for AS SDP which are starting from
HSW, as these defines are applicable for ADLP+.(Ankit)
--v4:
- Remove as_sdp_mode from crtc_state.
- Drop metadata keyword.
- For consistency, update ADL_ prefix or post fix as required.
--v5:
- Check if AS_SDP bit is set in crtc_state->infoframes.enable. If not
return.
- Check for HAS_AS_SDP() before setting VIDEO_DIP_ENABLE_AS_ADL mask.
--v6:
- Rename intel_read_dp_infoframe_as_sdp to intel_read_dp_as_sdp.
--v7:
- Add read back for length and vtotal correction.
--v8:
- Use as_sdp->target_rr & 0xFF.
- Shift by 8 instead of 32, and drop casting to u64.
- Remove changes which are does not belong to this patch.
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322031157.3823909-5-mitulkumar.ajitkumar.golani@intel.com
For DISPLAY < 13, compressed bpp is chosen from a list of
supported compressed bpps. Fix the condition to choose the
appropriate compressed bpp from the list.
Fixes: 1c56e9a398 ("drm/i915/dp: Get optimal link config to have best compressed bpp")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.7+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10162
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240305054443.2489895-1-ankit.k.nautiyal@intel.com
UHBR13.5 is not supported in MTL and also the DP2.1 spec says UHBR13.5
is optional. Hence removing UHBR135 from the supported link rates.
v2: Reframed the commit message and added link to the issue.
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Fixes: 62618c7f11 ("drm/i915/mtl: C20 PLL programming")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240228144350.3184930-1-arun.r.murthy@intel.com
If the sink supports 128b/132b and single-stream sideband messaging,
enable MST mode.
With this, the topology manager will still write DP_MSTM_CTRL, which
should be ignored by the sink. In the future, the topology manager
should probably only set the sideband messaging related parts of the
register.
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/39d753e53cd662c3fd3776b6167bf792219fd950.1710839496.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Drop the duplicate read of DP_MSTM_CAP DPCD register, and the duplicate
logic for choosing MST mode, and store the chosen mode in struct
intel_dp. Rename intel_dp_configure_mst() to intel_dp_mst_configure()
while at it.
v2: Rebase on drm_dp_mst_detect() returning the mode, not bool
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/93a48df9a77e1138bb28e645fae3f9c79b094cc7.1710839496.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Clarify the conditions for choosing the MST mode to use by adding a new
function intel_dp_mst_mode_choose(). This also prepares for being able
to extend the MST modes to single-stream sideband messaging.
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f626144f10b03d4609ff38a29bac013ecf3aca4e.1710839496.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rename intel_dp_can_mst() to intel_dp_mst_detect(), and move all DP MST
detect debug logging there. Debug log the sink's MST capability,
including single-stream sideband messaging support, and the decision
whether to enable MST mode or not. Do this regardless of whether we're
actually enabling MST or not.
We need to detect MST in intel_dp_detect_dpcd() before the earlier
returns, but try not to change the logic otherwise.
v2:
- Use "MST", "SST w/ sideband messaging", and "SST" for logging (Ville)
- Return MST mode from intel_dp_mst_detect()
- Do MST detect before early returns from intel_dp_detect_dpcd()
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/db08536daec0a6062539319d71c10ee1277e3876.1710839496.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Amend drm_dp_read_mst_cap() to return an enum, indicating "SST", "SST
with sideband messaging", or "MST". Modify all call sites to take the
new return value into account.
v2:
- Rename enumerators (Ville)
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b32a3704934871a67d06420b760e148b76c5ced8.1710839496.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
core:
- EDID cleanups
- scheduler error handling fixes
- managed: add drmm_release_action() with tests
- add ratelimited drm debug print
- DPCD PSR early transport macro
- DP tunneling and bandwidth allocation helpers
- remove built-in edids
- dp: Avoid AUX transfers on powered-down displays
- dp: Add VSC SDP helpers
cross drivers:
- use new drm print helpers
- switch to ->read_edid callback
- gem: add stats for shared buffers plus updates to amdgpu, i915, xe
syncobj:
- fixes to waiting and sleeping
ttm:
- add tests
- fix errno codes
- simply busy-placement handling
- fix page decryption
media:
- tc358743: fix v4l device registration
video:
- move all kernel parameters for video behind CONFIG_VIDEO
sound:
- remove <drm/drm_edid.h> include from header
ci:
- add tests for msm
- fix apq8016 runner
efifb:
- use copy of global screen_info state
vesafb:
- use copy of global screen_info state
simplefb:
- fix logging
bridge:
- ite-6505: fix DP link-training bug
- samsung-dsim: fix error checking in probe
- samsung-dsim: add bsh-smm-s2/pro boards
- tc358767: fix regmap usage
- imx: add i.MX8MP HDMI PVI plus DT bindings
- imx: add i.MX8MP HDMI TX plus DT bindings
- sii902x: fix probing and unregistration
- tc358767: limit pixel PLL input range
- switch to new drm_bridge_read_edid() interface
panel:
- ltk050h3146w: error-handling fixes
- panel-edp: support delay between power-on and enable; use put_sync in
unprepare; support Mediatek MT8173 Chromebooks, BOE NV116WHM-N49 V8.0,
BOE NV122WUM-N41, CSO MNC207QS1-1 plus DT bindings
- panel-lvds: support EDT ETML0700Z9NDHA plus DT bindings
- panel-novatek: FRIDA FRD400B25025-A-CTK plus DT bindings
- add BOE TH101MB31IG002-28A plus DT bindings
- add EDT ETML1010G3DRA plus DT bindings
- add Novatek NT36672E LCD DSI plus DT bindings
- nt36523: support 120Hz timings, fix includes
- simple: fix display timings on RK32FN48H
- visionox-vtdr6130: fix initialization
- add Powkiddy RGB10MAX3 plus DT bindings
- st7703: support panel rotation plus DT bindings
- add Himax HX83112A plus DT bindings
- ltk500hd1829: add support for ltk101b4029w and admatec 9904370
- simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs
panel-orientation-quirks:
- GPD Win Mini
amdgpu:
- Validate DMABuf imports in compute VMs
- Add RAS ACA framework
- PSP 13 fixes
- Misc code cleanups
- Replay fixes
- Atom interpretor PS, WS bounds checking
- DML2 fixes
- Audio fixes
- DCN 3.5 Z state fixes
- Remove deprecated ida_simple usage
- UBSAN fixes
- RAS fixes
- Enable seq64 infrastructure
- DC color block enablement
- Documentation updates
- DC documentation updates
- DMCUB updates
- ATHUB 4.1 support
- LSDMA 7.0 support
- JPEG DPG support
- IH 7.0 support
- HDP 7.0 support
- VCN 5.0 support
- SMU 13.0.6 updates
- NBIO 7.11 updates
- SDMA 6.1 updates
- MMHUB 3.3 updates
- DCN 3.5.1 support
- NBIF 6.3.1 support
- VPE 6.1.1 support
amdkfd:
- Validate DMABuf imports in compute VMs
- SVM fixes
- Trap handler updates and enhancements
- Fix cache size reporting
- Relocate the trap handler
radeon:
- Atom interpretor PS, WS bounds checking
- Misc code cleanups
xe:
- new query for GuC submission version
- Remove unused persistent exec_queues
- Add vram frequency sysfs attributes
- Add the flag XE_VM_BIND_FLAG_DUMPABLE
- Drop pre-production workarounds
- Drop kunit tests for unsupported platforms
- Start pumbling SR-IOV support with memory based interrupts for VF
- Allow to map BO in GGTT with PAT index corresponding to
XE_CACHE_UC to work with memory based interrupts
- Add GuC Doorbells Manager as prep work SR-IOV
- Implement additional workarounds for xe2 and MTL
- Program a few registers according to perfomance guide spec for Xe2
- Fix remaining 32b build issues and enable it back
- Fix build with CONFIG_DEBUG_FS=n
- Fix warnings from GuC ABI headers
- Introduce Relay Communication for SR-IOV for VF <-> GuC <-> PF
- Release mmap mappings on rpm suspend
- Disable mid-thread preemption when not properly supported by hardware
- Fix xe_exec by reserving extra fence slot for CPU bind
- Fix xe_exec with full long running exec queue
- Canonicalize addresses where needed for Xe2 and add to devcoredum
- Toggle USM support for Xe2
- Only allow 1 ufence per exec / bind IOCTL
- Add GuC firmware loading for Lunar Lake
- Add XE_VMA_PTE_64K VMA flag
i915:
- Add more ADL-N PCI IDs
- Enable fastboot also on older platforms
- Early transport for panel replay and PSR
- New ARL PCI IDs
- DP TPS4 PHY test pattern support
- Unify and improve VSC SDP for PSR and non-PSR cases
- Refactor memory regions and improve debug logging
- Rework global state serialization
- Remove unused CDCLK divider fields
- Unify HDCP connector logging format
- Use display instead of graphics version in display code
- Move VBT and opregion debugfs next to the implementation
- Abstract opregion interface, use opaque type
- MTL fixes
- HPD handling fixes
- Add GuC submission interface version query
- Atomically invalidate userptr on mmu-notifier
- Update handling of MMIO triggered reports
- Don't make assumptions about intel_wakeref_t type
- Extend driver code of Xe_LPG to Xe_LPG+
- Add flex arrays to struct i915_syncmap
- Allow for very slow HuC loading
- DP tunneling and bandwidth allocation support
msm:
- Correct bindings for MSM8976 and SM8650 platforms
- Start migration of MDP5 platforms to DPU driver
- X1E80100 MDSS support
- DPU:
- Improve DSC allocation, fixing several important corner cases
- Add support for SDM630/SDM660 platforms
- Simplify dpu_encoder_phys_ops
- Apply fixes targeting DSC support with a single DSC encoder
- Apply fixes for HCTL_EN timing configuration
- X1E80100 support
- Add support for YUV420 over DP
- GPU:
- fix sc7180 UBWC config
- fix a7xx LLC config
- new gpu support: a305B, a750, a702
- machine support: SM7150 (different power levels than other a618)
- a7xx devcoredump support
habanalabs:
- configure IRQ affinity according to NUMA node
- move HBM MMU page tables inside the HBM
- improve device reset
- check extended PCIe errors
ivpu:
- updates to firmware API
- refactor BO allocation
imx:
- use devm_ functions during init
hisilicon:
- fix EDID includes
mgag200:
- improve ioremap usage
- convert to struct drm_edid
- Work around PCI write bursts
nouveau:
- disp: use kmemdup()
- fix EDID includes
- documentation fixes
qaic:
- fixes to BO handling
- make use of DRM managed release
- fix order of remove operations
rockchip:
- analogix_dp: get encoder port from DT
- inno_hdmi: support HDMI for RK3128
- lvds: error-handling fixes
ssd130x:
- support SSD133x plus DT bindings
tegra:
- fix error handling
tilcdc:
- make use of DRM managed release
v3d:
- show memory stats in debugfs
- Support display MMU page size
vc4:
- fix error handling in plane prepare_fb
- fix framebuffer test in plane helpers
virtio:
- add venus capset defines
vkms:
- fix OOB access when programming the LUT
- Kconfig improvements
vmwgfx:
- unmap surface before changing plane state
- fix memory leak in error handling
- documentation fixes
- list command SVGA_3D_CMD_DEFINE_GB_SURFACE_V4 as invalid
- fix null-pointer deref in execbuf
- refactor display-mode probing
- fix fencing for creating cursor MOBs
- fix cursor-memory lifetime
xlnx:
- fix live video input for ZynqMP DPSUB
lima:
- fix memory leak
loongson:
- fail if no VRAM present
meson:
- switch to new drm_bridge_read_edid() interface
renesas:
- add RZ/G2L DU support plus DT bindings
mxsfb:
- Use managed mode config
sun4i:
- HDMI: updates to atomic mode setting
mediatek:
- Add display driver for MT8188 VDOSYS1
- DSI driver cleanups
- Filter modes according to hardware capability
- Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
etnaviv:
- enhancements for NPU and MRT support
-----BEGIN PGP SIGNATURE-----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=WLj9
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2024-03-13' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"Highlights are usual, more AMD IP blocks for future hw, i915/xe
changes, Displayport tunnelling support for i915, msm YUV over DP
changes, new tests for ttm, but its mostly a lot of stuff all over the
place from lots of people.
core:
- EDID cleanups
- scheduler error handling fixes
- managed: add drmm_release_action() with tests
- add ratelimited drm debug print
- DPCD PSR early transport macro
- DP tunneling and bandwidth allocation helpers
- remove built-in edids
- dp: Avoid AUX transfers on powered-down displays
- dp: Add VSC SDP helpers
cross drivers:
- use new drm print helpers
- switch to ->read_edid callback
- gem: add stats for shared buffers plus updates to amdgpu, i915, xe
syncobj:
- fixes to waiting and sleeping
ttm:
- add tests
- fix errno codes
- simply busy-placement handling
- fix page decryption
media:
- tc358743: fix v4l device registration
video:
- move all kernel parameters for video behind CONFIG_VIDEO
sound:
- remove <drm/drm_edid.h> include from header
ci:
- add tests for msm
- fix apq8016 runner
efifb:
- use copy of global screen_info state
vesafb:
- use copy of global screen_info state
simplefb:
- fix logging
bridge:
- ite-6505: fix DP link-training bug
- samsung-dsim: fix error checking in probe
- samsung-dsim: add bsh-smm-s2/pro boards
- tc358767: fix regmap usage
- imx: add i.MX8MP HDMI PVI plus DT bindings
- imx: add i.MX8MP HDMI TX plus DT bindings
- sii902x: fix probing and unregistration
- tc358767: limit pixel PLL input range
- switch to new drm_bridge_read_edid() interface
panel:
- ltk050h3146w: error-handling fixes
- panel-edp: support delay between power-on and enable; use put_sync
in unprepare; support Mediatek MT8173 Chromebooks, BOE NV116WHM-N49
V8.0, BOE NV122WUM-N41, CSO MNC207QS1-1 plus DT bindings
- panel-lvds: support EDT ETML0700Z9NDHA plus DT bindings
- panel-novatek: FRIDA FRD400B25025-A-CTK plus DT bindings
- add BOE TH101MB31IG002-28A plus DT bindings
- add EDT ETML1010G3DRA plus DT bindings
- add Novatek NT36672E LCD DSI plus DT bindings
- nt36523: support 120Hz timings, fix includes
- simple: fix display timings on RK32FN48H
- visionox-vtdr6130: fix initialization
- add Powkiddy RGB10MAX3 plus DT bindings
- st7703: support panel rotation plus DT bindings
- add Himax HX83112A plus DT bindings
- ltk500hd1829: add support for ltk101b4029w and admatec 9904370
- simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs
panel-orientation-quirks:
- GPD Win Mini
amdgpu:
- Validate DMABuf imports in compute VMs
- Add RAS ACA framework
- PSP 13 fixes
- Misc code cleanups
- Replay fixes
- Atom interpretor PS, WS bounds checking
- DML2 fixes
- Audio fixes
- DCN 3.5 Z state fixes
- Remove deprecated ida_simple usage
- UBSAN fixes
- RAS fixes
- Enable seq64 infrastructure
- DC color block enablement
- Documentation updates
- DC documentation updates
- DMCUB updates
- ATHUB 4.1 support
- LSDMA 7.0 support
- JPEG DPG support
- IH 7.0 support
- HDP 7.0 support
- VCN 5.0 support
- SMU 13.0.6 updates
- NBIO 7.11 updates
- SDMA 6.1 updates
- MMHUB 3.3 updates
- DCN 3.5.1 support
- NBIF 6.3.1 support
- VPE 6.1.1 support
amdkfd:
- Validate DMABuf imports in compute VMs
- SVM fixes
- Trap handler updates and enhancements
- Fix cache size reporting
- Relocate the trap handler
radeon:
- Atom interpretor PS, WS bounds checking
- Misc code cleanups
xe:
- new query for GuC submission version
- Remove unused persistent exec_queues
- Add vram frequency sysfs attributes
- Add the flag XE_VM_BIND_FLAG_DUMPABLE
- Drop pre-production workarounds
- Drop kunit tests for unsupported platforms
- Start pumbling SR-IOV support with memory based interrupts for VF
- Allow to map BO in GGTT with PAT index corresponding to XE_CACHE_UC
to work with memory based interrupts
- Add GuC Doorbells Manager as prep work SR-IOV
- Implement additional workarounds for xe2 and MTL
- Program a few registers according to perfomance guide spec for Xe2
- Fix remaining 32b build issues and enable it back
- Fix build with CONFIG_DEBUG_FS=n
- Fix warnings from GuC ABI headers
- Introduce Relay Communication for SR-IOV for VF <-> GuC <-> PF
- Release mmap mappings on rpm suspend
- Disable mid-thread preemption when not properly supported by
hardware
- Fix xe_exec by reserving extra fence slot for CPU bind
- Fix xe_exec with full long running exec queue
- Canonicalize addresses where needed for Xe2 and add to devcoredum
- Toggle USM support for Xe2
- Only allow 1 ufence per exec / bind IOCTL
- Add GuC firmware loading for Lunar Lake
- Add XE_VMA_PTE_64K VMA flag
i915:
- Add more ADL-N PCI IDs
- Enable fastboot also on older platforms
- Early transport for panel replay and PSR
- New ARL PCI IDs
- DP TPS4 PHY test pattern support
- Unify and improve VSC SDP for PSR and non-PSR cases
- Refactor memory regions and improve debug logging
- Rework global state serialization
- Remove unused CDCLK divider fields
- Unify HDCP connector logging format
- Use display instead of graphics version in display code
- Move VBT and opregion debugfs next to the implementation
- Abstract opregion interface, use opaque type
- MTL fixes
- HPD handling fixes
- Add GuC submission interface version query
- Atomically invalidate userptr on mmu-notifier
- Update handling of MMIO triggered reports
- Don't make assumptions about intel_wakeref_t type
- Extend driver code of Xe_LPG to Xe_LPG+
- Add flex arrays to struct i915_syncmap
- Allow for very slow HuC loading
- DP tunneling and bandwidth allocation support
msm:
- Correct bindings for MSM8976 and SM8650 platforms
- Start migration of MDP5 platforms to DPU driver
- X1E80100 MDSS support
- DPU:
- Improve DSC allocation, fixing several important corner cases
- Add support for SDM630/SDM660 platforms
- Simplify dpu_encoder_phys_ops
- Apply fixes targeting DSC support with a single DSC encoder
- Apply fixes for HCTL_EN timing configuration
- X1E80100 support
- Add support for YUV420 over DP
- GPU:
- fix sc7180 UBWC config
- fix a7xx LLC config
- new gpu support: a305B, a750, a702
- machine support: SM7150 (different power levels than other a618)
- a7xx devcoredump support
habanalabs:
- configure IRQ affinity according to NUMA node
- move HBM MMU page tables inside the HBM
- improve device reset
- check extended PCIe errors
ivpu:
- updates to firmware API
- refactor BO allocation
imx:
- use devm_ functions during init
hisilicon:
- fix EDID includes
mgag200:
- improve ioremap usage
- convert to struct drm_edid
- Work around PCI write bursts
nouveau:
- disp: use kmemdup()
- fix EDID includes
- documentation fixes
qaic:
- fixes to BO handling
- make use of DRM managed release
- fix order of remove operations
rockchip:
- analogix_dp: get encoder port from DT
- inno_hdmi: support HDMI for RK3128
- lvds: error-handling fixes
ssd130x:
- support SSD133x plus DT bindings
tegra:
- fix error handling
tilcdc:
- make use of DRM managed release
v3d:
- show memory stats in debugfs
- Support display MMU page size
vc4:
- fix error handling in plane prepare_fb
- fix framebuffer test in plane helpers
virtio:
- add venus capset defines
vkms:
- fix OOB access when programming the LUT
- Kconfig improvements
vmwgfx:
- unmap surface before changing plane state
- fix memory leak in error handling
- documentation fixes
- list command SVGA_3D_CMD_DEFINE_GB_SURFACE_V4 as invalid
- fix null-pointer deref in execbuf
- refactor display-mode probing
- fix fencing for creating cursor MOBs
- fix cursor-memory lifetime
xlnx:
- fix live video input for ZynqMP DPSUB
lima:
- fix memory leak
loongson:
- fail if no VRAM present
meson:
- switch to new drm_bridge_read_edid() interface
renesas:
- add RZ/G2L DU support plus DT bindings
mxsfb:
- Use managed mode config
sun4i:
- HDMI: updates to atomic mode setting
mediatek:
- Add display driver for MT8188 VDOSYS1
- DSI driver cleanups
- Filter modes according to hardware capability
- Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
etnaviv:
- enhancements for NPU and MRT support"
* tag 'drm-next-2024-03-13' of https://gitlab.freedesktop.org/drm/kernel: (1420 commits)
drm/amd/display: Removed redundant @ symbol to fix kernel-doc warnings in -next repo
drm/amd/pm: wait for completion of the EnableGfxImu message
drm/amdgpu/soc21: add mode2 asic reset for SMU IP v14.0.1
drm/amdgpu: add smu 14.0.1 support
drm/amdgpu: add VPE 6.1.1 discovery support
drm/amdgpu/vpe: add VPE 6.1.1 support
drm/amdgpu/vpe: don't emit cond exec command under collaborate mode
drm/amdgpu/vpe: add collaborate mode support for VPE
drm/amdgpu/vpe: add PRED_EXE and COLLAB_SYNC OPCODE
drm/amdgpu/vpe: add multi instance VPE support
drm/amdgpu/discovery: add nbif v6_3_1 ip block
drm/amdgpu: Add nbif v6_3_1 ip block support
drm/amdgpu: Add pcie v6_1_0 ip headers (v5)
drm/amdgpu: Add nbif v6_3_1 ip headers (v5)
arch/powerpc: Remove <linux/fb.h> from backlight code
macintosh/via-pmu-backlight: Include <linux/backlight.h>
fbdev/chipsfb: Include <linux/backlight.h>
drm/etnaviv: Restore some id values
drm/amdkfd: make kfd_class constant
drm/amdgpu: add ring timeout information in devcoredump
...
Move psr_init_dpcd() from init-connector to connector-detect
function. The dpcd probe for checking panel replay capability
for external dp connector is causing delay during boot which can
be optimized by moving dpcd probe to connector specific detect().
v1: Initial version.
v2: Add details in commit description. [Jani]
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10284
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Fixes: cceeaa312d ("drm/i915/panelreplay: Enable panel replay dpcd initialization for DP")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240229043716.4065760-1-animesh.manna@intel.com
(cherry picked from commit 1cca19bf29)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The DSC HW state of DP connectors is read out during driver loading and
system resume in intel_modeset_update_connector_atomic_state(). This
function is called for all connectors though and so the state of DSI
connectors will also get updated incorrectly, triggering a WARN there
wrt. the DSC decompression AUX device.
Fix the above by moving the DSC state readout to a new DP connector
specific sync_state() hook. This is anyway the logical place to update
the connector object's state vs. the connector's atomic state.
Fixes: b2608c6b32 ("drm/i915/dp_mst: Enable MST DSC decompression for all streams")
Reported-and-tested-by: Drew Davenport <ddavenport@chromium.org>
Closes: https://lore.kernel.org/all/Zb0q8IDVXS0HxJyj@chromium.org
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240205132631.1588577-1-imre.deak@intel.com
(cherry picked from commit a62e145981)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The DSC HW state of DP connectors is read out during driver loading and
system resume in intel_modeset_update_connector_atomic_state(). This
function is called for all connectors though and so the state of DSI
connectors will also get updated incorrectly, triggering a WARN there
wrt. the DSC decompression AUX device.
Fix the above by moving the DSC state readout to a new DP connector
specific sync_state() hook. This is anyway the logical place to update
the connector object's state vs. the connector's atomic state.
Fixes: b2608c6b32 ("drm/i915/dp_mst: Enable MST DSC decompression for all streams")
Reported-and-tested-by: Drew Davenport <ddavenport@chromium.org>
Closes: https://lore.kernel.org/all/Zb0q8IDVXS0HxJyj@chromium.org
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240205132631.1588577-1-imre.deak@intel.com
Move psr_init_dpcd() from init-connector to connector-detect
function. The dpcd probe for checking panel replay capability
for external dp connector is causing delay during boot which can
be optimized by moving dpcd probe to connector specific detect().
v1: Initial version.
v2: Add details in commit description. [Jani]
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10284
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Fixes: cceeaa312d ("drm/i915/panelreplay: Enable panel replay dpcd initialization for DP")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240229043716.4065760-1-animesh.manna@intel.com
Detect DP tunnels and enable the BW allocation mode on them. Send a
hotplug notification to userspace in response to a BW change.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-22-imre.deak@intel.com
The TBT DP tunnel BW request logic in the Thunderbolt Connection Manager
depends on the GFX driver reading out the sink's DPRX capabilities in
response to a long HPD pulse. Since in i915 this read-out can be blocked
by another connector's/encoder's hotplug event handling (which is
serialized by drm_mode_config::connection_mutex), do a dummy DPRX read-out
in the encoder's HPD pulse handler (which is not blocked by other
encoders).
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-21-imre.deak@intel.com
Suspend and resume DP tunnels during system suspend/resume, disabling
the BW allocation mode during suspend, re-enabling it after resume. This
reflects the link's BW management component (Thunderbolt CM) disabling
BWA during suspend. Before any BW requests the driver must read the
sink's DPRX capabilities (since the BW manager requires this
information, so snoops for it on AUX), so ensure this read takes place.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-20-imre.deak@intel.com
Handle DP tunnel IRQs a sink (or rather a BW management component like
the Thunderbolt Connection Manager) raises to signal the completion of a
BW request by the driver, or to signal any state change related to the
link BW.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-18-imre.deak@intel.com
Compute the BW required through a DP tunnel on links with such tunnels
detected and add the corresponding atomic state during a modeset.
v2:
- Fix error check of intel_dp_tunnel_compute_stream_bw(). (Ville)
- Move intel_dp_tunnel_atomic_cleanup_inherited_state() to this patch.
(Ville)
- Move intel_dp_tunnel_atomic_clear_stream_bw() to this patch.
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-16-imre.deak@intel.com
Take any link BW limitation into account in
intel_dp_max_link_data_rate(). Such a limitation can be due to multiple
displays on (Thunderbolt) links with DP tunnels sharing the link BW.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-15-imre.deak@intel.com
Sync instead of only try-sync non-blocking commits when getting the
active pipes through a given DP port. Atm intel_dp_get_active_pipes()
will only try to sync a given pipe and if that would block ignore the
pipe. This was supposed to avoid link retraining in case a pending
modeset would do that anyway, however that could incorrectly ignore
fastset pipes as well for instance (which don't retraing the link).
The TC port reset path needs to handle all pipes, even if a waiting for
a pending commit would block. To account for the above cases sync all
the pipes unconditionally.
This also prepares for a follow-up change enabling the DP tunnel BW
allocation mode which needs to ensure that all active pipes are synced
and returned from intel_dp_get_active_pipes().
v2:
- Add a separate function to try-sync the pipes. (Ville)
v3:
- Just sync the pipes unconditionally in intel_dp_get_active_pipes().
(Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240226185246.1276018-3-imre.deak@intel.com
Add intel_dp_max_link_data_rate() to get the link BW vs. the sink DPRX
BW used by a follow-up patch enabling the DP tunnel BW allocation mode.
The link BW can be below the DPRX BW due to a BW limitation on a link
shared by multiple sinks.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-11-imre.deak@intel.com
Factor out a function updating the sink's link rate and lane count
capabilities, used by a follow-up patch enabling the DP tunnel BW
allocation mode.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-9-imre.deak@intel.com
Export intel_dp_max_common_rate() and intel_dp_max_lane_count() used by
a follow-up patch enabling the DP tunnel BW allocation mode.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-8-imre.deak@intel.com
Factor out intel_dp_config_required_rate() used by a follow-up patch
enabling the DP tunnel BW allocation mode.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-7-imre.deak@intel.com
Instead of intel_dp_max_data_rate() use the equivalent
drm_dp_max_dprx_data_rate() which was copied from the former one in a
previous patch.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-6-imre.deak@intel.com
On shared (Thunderbolt) links with DP tunnels, the modeset may need to
be retried on all connectors on the link due to a link BW limitation
arising only after the atomic check phase. To support this add a helper
function queuing a work to retry the modeset on a given port's connector
and at the same time any MST connector with streams through the same
port. A follow-up change enabling the DP tunnel Bandwidth Allocation
Mode will take this into use.
v2:
- Send the uevent only to enabled MST connectors. (Jouni)
Cc: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220211841.448846-5-imre.deak@intel.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmXb0T4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG5YQH/3eCV90sNGch0Y94
8rtTdqFrVx7QPNl0pz+Mo6OUIKUUHvTuwime16ckLxG+3x2Y3I0MjP1edd1NB99C
Kje//JTpaZBPpTZ/jY4u8B1Shov2Drdx/J4NFnE/9rG6yXzKQBtvON/xAxXDCVHT
mLhst2LR0FeCSMk9jAX6CoqUPEgwlylNyAetKxaDQgoHl4GTZC7FDO17WxyjpIxe
1rVHsrV9Eq8kD4uxrzpTYWgZrwTObPmlZjvefa1JfzSwRNABIBJj/C1nra1Zc1oi
b7xVaXS1cMOxrtuuG00fmHsPnWivu0tuND7H3/yLd1mRCZAPSsVbVvrI/KNtoeV4
1euINlY=
=7IFt
-----END PGP SIGNATURE-----
Merge v6.8-rc6 into drm-next
Thomas Zimmermann asked to backmerge -rc6 for drm-misc branches,
there's a few same-area-changed conflicts (xe and amdgpu mostly) that
are getting a bit too annoying.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 47f419e071 ("drm/dp: move intel_dp_vsc_sdp_pack() to generic helper")
and commit b55b88d86f ("drm/dp: drop the size parameter from drm_dp_vsc_sdp_pack()")
were based on top of a tree containing the
commit 31a5b6ed88 ("drm/i915/display: Unify VSC SPD preparation") but
landed in a tree where this commit didn't exist, leaving behind a spurious
case calling for a removed function: intel_dp_vsc_sdp_pack()
Let's convert the remaining case here so we can port this patch to
any tree that doesn't contain
commit 31a5b6ed88 ("drm/i915/display: Unify VSC SPD preparation")
In in kind of merge where this commit does exist, this line here will
be gone anyway and not needed any longer.
Fixes: 47f419e071 ("drm/dp: move intel_dp_vsc_sdp_pack() to generic helper")
Cc: Dave Airlie <airlied@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223191548.392185-1-rodrigo.vivi@intel.com
Currently the size parameter of drm_dp_vsc_sdp_pack() is always
the size of struct dp_sdp. Hence lets drop this parameter and
use sizeof() directly.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-2-quic_abhinavk@quicinc.com
intel_dp_vsc_sdp_pack() can be re-used by other DRM drivers as well.
Lets move this to drm_dp_helper to achieve this.
changes in v2:
- rebased on top of drm-tip
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240220195348.1270854-1-quic_abhinavk@quicinc.com
For validation purposes, it might be useful to be able to
force Bigjoiner mode, even if current dotclock/resolution
do not require that.
Lets add such to option to debugfs.
v2: - Apparently intel_dp_need_bigjoiner can't be used, when
debugfs entry is created so lets just check manually
the DISPLAY_VER.
v3: - Switch to intel_connector from drm_connector(Jani Nikula)
- Remove redundant modeset lock(Jani Nikula)
- Use kstrtobool_from_user for boolean value(Jani Nikula)
v4: - Apply the changes to proper function(Jani Nikula)
v5: - Removed unnecessary check from i915_bigjoiner_enable_show
(Ville Syrjälä)
- Added eDP connector check to intel_connector_debugfs_add
(Ville Syrjälä)
- Removed debug message in order to prevent dmesg flooding
(Ville Syrjälä)
v6: - Assume now always that m->private is intel_connector
- Fixed other similar conflicts
v7: - Move bigjoiner force option to intel_connector(Ville Syrjälä)
- Use DEFINE_SHOW_STORE_ATTRIBUTE instead of defining fops
manually.(Ville Syrjälä)
v8: - Pass intel_connector to debugfs_create_file, instead of drm_connector.
(Jani Nikula)
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240212125011.66174-1-uma.shankar@intel.com
Imre Deak
Jani Nikula
Clint Taylor
Suraj Kandpal
Ville Syrjälä
R Sundar
Shuicheng Lin
Stanislav Lisovskiy
Ankit Nautiyal
Yuesong Li
Chaitanya Kumar Borah
Arun R Murthy
Jouni Högander
Rodrigo Vivi
Daniel Vetter
Mitul Golani
Colin Ian King
Imre Deak
Animesh Manna
Balasubramani Vivekanandan
Bhanuprakash Modem
Linus Torvalds
Dave Airlie
Thomas Zimmermann
Abhinav Kumar