Make HSW/BDW use port_mask for output probing as well.
To achieve that the strap checks are moved into
intel_ddi_init() itself. Or should we move them to the
runtime port_mask init instead? Maybe not since the hardware
is still there, just not connected to anything.
v2: Account for DDI-E in strap detection
Keep to the old CRT->DDI init order
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-8-ville.syrjala@linux.intel.com
Sprinkle some asserts to catch any mishaps in the port_mask
vs. output init.
For DDI/DP/HDMI/SDVO I decided that we want to bail out for
an invalid port since those are the encoder types where
we might want consider driving the whole thing from the VBT
child device list, and bogus VBTs could be a real issue
(if for no other reason than the i915.vbt_firmware).
For DVO and HSW/BDW CRT port I just threw the assert in
there for good measure.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-5-ville.syrjala@linux.intel.com
If the output on a DP-alt link with its sink disconnected is kept
enabled for too long (about 20 sec), then some IOM/TCSS firmware timeout
will cause havoc on the PCI bus, at least for other GFX devices on it
which will stop powering up. Since user space is not guaranteed to do a
disabling modeset in time, switch such disconnected but active links to
TBT mode - which is without such shortcomings - with a 2 second delay.
If the above condition is detected already during the driver load/system
resume sanitization step disable the output instead, as at that point no
user space or kernel client depends on a consistent output state yet and
because subsequent atomic modeset on such connectors - without the
actual sink capabilities available - can fail.
An active/disconnected port as above will also block the HPD status of
other active/disconnected ports to get updated (stuck in the connected
state), until the former port is disabled, its PHY is disconnected and
a ~10 ms delay has elapsed. This means the link state for all TypeC
ports/CRTCs must be rechecked after a CRTC is disabled due to the above
reason. For this disconnect the PHY synchronously after the CRTC/port is
disabled and recheck all CRTCs for the above condition whenever such a
port is disabled.
To account for a race condition during driver loading where the sink is
disconnected after the above sanitization step and before the HPD
interrupts get enabled, do an explicit check/link reset if needed from
the encoder's late_register hook, which is called after the HPD
interrupts are enabled already.
v2:
- Handle an active/disconnected port blocking the HPD state update of
another active/disconnected port.
- Cancel the delayed work resetting the link also from the encoder
enable/suspend/shutdown hooks.
- Rebase on the earlier intel_modeset_lock_ctx_retry() addition,
fixing here the missed atomic state reset in case of a retry.
- Fix handling of an error return from intel_atomic_get_crtc_state().
- Recheck if the port needs to be reset after all the atomic state
is locked and async commits are waited on.
v3:
- Add intel_crtc_needs_link_reset(), instead of open-coding it,
keep intel_crtc_has_encoders(). (Ville)
- Fix state dumping and use a bitmask to track disabled CRTCs in
intel_sanitize_all_crtcs(). (Ville)
- Set internal in intel_atomic_state right after allocating it.
(Ville)
- Recheck all CRTCs (not yet force-disabled) after a CRTC is
force-disabled for any reason (not only due to a link state)
in intel_sanitize_all_crtcs().
- Reduce delay after CRTC disabling to 20ms, and use the simpler
msleep().
- Clarify code comment about HPD behaviour in
intel_sanitize_all_crtcs().
- Move all the TC link reset logic to intel_tc.c .
- Cancel the link reset work synchronously during system suspend,
driver unload and shutdown.
v4:
- Rebased on previous patch, which allows calling the TC port
suspend/cleanup handlers without modeset locks held; remove the
display driver suspended assert from the link reset work
accordingly.
v5: (Ville)
- Remove reset work canceling from intel_ddi_pre_pll_enable().
- Track a crtc vs. pipe mask in intel_sanitize_all_crtcs().
- Add reset_link_commit() to clarify the
intel_modeset_lock_ctx_retry loop.
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5860
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-2-imre.deak@intel.com
Call the TypeC port flush_work and cleanup handlers without the modeset
locks held. These don't require the locks, as the work takes - as it
should be able to at any point in time - any locks it needs and by the
time cleanup is called and after cleanup returns the encoder is not in
use.
This is required by the next patch canceling a TypeC port work
synchronously during encoder suspend and shutdown, where the work can
take modeset locks as well, hence the canceling must be done without
holding the locks.
I also considered moving the modeset locking down to each encoder
suspend()/shutdown() hook instead, however locking the full modeset
state for each encoder separately would be odd, and the bigger change -
affecting all encoders - is beyond the scope of this patchset.
v2:
- Add a TODO: comment to remove modeset locks if no encoder depends
on this. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512195513.2699-1-imre.deak@intel.com
This patch simplifying the handling of modeset locks and atomic state
for an atomic commit is based on
https://lore.kernel.org/all/20210715184954.7794-2-ville.syrjala@linux.intel.com/
adding the helper to i915. I find this approach preferrable than
open-coding the corresponding steps (fixed for me an atomic
state reset during a DEADLK retry, which I missed in the open-coded
version) and also better than the existing
DRM_MODESET_LOCK_ALL_BEGIN/END macros for the reasons described in the
above original patchset.
This change takes the helper into use only for atomic commits during DDI
hotplug handling, as a preparation for a follow-up patch adding a
similar commit started from the same spot. Other places doing a
driver-internal atomic commit is to be converted by a follow-up
patchset.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-13-imre.deak@intel.com
Pass all the parameter in intel_encoder->enable()
to intel_hdcp_enable as we need intel_atomic_state
later down to get acquire_ctx.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230515103225.688830-2-suraj.kandpal@intel.com
We'll be wanting to compute has_hdmi_sink a bit differently
for some platforms. To that end compute it in the encoder
.compute_config_hook() before we call intel_hdmi_compute_config().
intel_hdmi_compute_has_hdmi_sink() will do the basic lifting
beyond any platform specific stuff.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221107194604.15227-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
As we already do with C10 chip, let's dump the pll
hw state for C20 as well.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-4-mika.kahola@intel.com
Create a table for C20 DP1.4, DP2.0 and HDMI2.1 rates.
The PLL settings are based on table, not for algorithmic alternative.
For DP 1.4 only MPLLB is in use.
Once register settings are done, we read back C20 HW state.
BSpec: 64568
v2: Updated pll tables (RK)
MPLLB selection fix (RK)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-3-mika.kahola@intel.com
C20 phy PLL programming sequence for DP, DP2.0, HDMI2.x non-FRL and
HDMI2.x FRL. This enables C20 MPLLA and MPLLB programming sequence. add
4 lane support for c20.
v2: Add 6.48Gbps and 6.75Gbps modes for eDP (RK)
Fix lane check (RK)
Fix multiline commenting (Arun)
use usleep_range() instead of msleep() (Andi)
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-2-mika.kahola@intel.com
The port PLL selection needs to be up-to-date in the CRTC state of both
the primary and all secondary MST streams. The commit removing the
encoder update_prepare/complete hooks (see Fixes: below), stopped doing
this for secondary streams, fix this up.
Fixes: 0f752b2178 ("drm/i915: Remove the encoder update_prepare()/complete() hooks")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8336
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230414173800.590790-1-imre.deak@intel.com
(cherry picked from commit 27ac123b45)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The port PLL selection needs to be up-to-date in the CRTC state of both
the primary and all secondary MST streams. The commit removing the
encoder update_prepare/complete hooks (see Fixes: below), stopped doing
this for secondary streams, fix this up.
Fixes: 0f752b2178 ("drm/i915: Remove the encoder update_prepare()/complete() hooks")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8336
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230414173800.590790-1-imre.deak@intel.com
MTL requires the PORT_CTL_WIDTH, TRANS_DDI_FUNC_CTL and DDI_BUF_CTL
to be filled with 4 lanes for TMDS mode.
This patch enables D2D link and fills PORT_WIDTH in appropriate
registers.
v2:
- Added fixes from Clint's Add HDMI implementation changes.
- Modified commit message.
v3:
- Use TRANS_DDI_PORT_WIDTH() instead of DDI_PORT_WIDTH() for the value
of TRANS_DDI_FUNC_CTL_*. (Gustavo)
Cc: Taylor, Clinton A <clinton.a.taylor@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-9-radhakrishna.sripada@intel.com
The differences between MTL and TGL DP sequences are big enough to
MTL have its own functions.
Also it is much easier to follow MTL sequences against spec with
its own functions.
One change worthy to mention is the move of
'intel_display_power_get(dev_priv, dig_port->ddi_io_power_domain)'.
This call is not necessary for MTL but we have _put() counter part in
intel_ddi_post_disable_dp() that needs to balanced.
We could add a display version check on it but instead here it is
moving it to intel_ddi_pre_enable_dp() so it is executed for all
platforms in a single place and this will not cause any harm in MTL
and newer platforms.
v2:
- Fix logic to wait for buf idle.
- Use the right register to wait for ddi active.(RK)
v3:
- Increase wait timeout for ddi buf active (Mika)
v4:
- Increase idle timeout for ddi buf idle (Mika)
v5: use rmw in mtl_disable_ddi_buf. Donot clear
link training mask(Imre)
BSpec: 65448 65505
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Satyeshwar Singh <satyeshwar.singh@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-7-radhakrishna.sripada@intel.com
C10 phys uses direct mapping internally for voltage and pre-emphasis levels.
Program the levels directly to the fields in the VDR Registers.
Bspec: 65449
v2: From table "C10: Tx EQ settings for DP 1.4x" it shows level 1
and preemphasis 1 instead of two times of level 1 preemphasis 0.
Fix this in the driver code as well.
v3: VSwing update (Clint)
v4: Add vboost termination ctl programming(Imre)
Fix tx llogic and other nits
Restrict C10 vdr ctl register access for C10 phy(RK)
v5: Program vboots, termination ctl for both lanes(Imre)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>(v3)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-5-radhakrishna.sripada@intel.com
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
If we have to force the hardware to go through a full modeset
due to eg. cdclk reprogramming, we need to preserve
crtc_state->inherited for all crtcs that have not otherwise
gone through the whole compute_config() stuff after connectors
have been detected.
Otherwise eg. cdclk induced modeset glk_force_audio_cdclk()
will clear the inherited flag, and thus the first real commit
coming from userspace later on will not be forced through
the full .compute_config() path and so eg. audio state may
not get properly recomputed.
But instead of adding all kinds of ad-hoc crtc_state->inherited
preservation hacks all over, let's change things so that we
only clear it for the crtcs directly included in userspace/client
initiated commits.
Should be far less fragile since now we just need to remember
to flag the internal commits, and not worry about where new
crtcs might get pulled in.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5260
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230328122357.1697-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Move VRR enabling/disabling into a place where it also works
for fastsets.
With this we always start the transcoder up in non-VRR mode.
Granted we already did that but for a very short period of
time. But now that we might end up doing a bit more with the
transcoder in non-VRR mode it seems prudent to also update
the active timings as the transcoder changes its operating
mode.
crtc_state->vrr.enable still tracks whether VRR is actually
enabled or not, but now we configure all the other VRR timing
registers whenever VRR is possible (whether we actually enable
it or not). crtc_state->vrr.flipline can now serve as our
"is VRR possible" bit of state.
I decided to leave the MSA timing ignore bit set all the time
whether VRR is actually enabled or not. If the sink can figure
out the timings with that information when VRR is active then
surely it can also do it when VRR is inactive.
v2: Protect intel_vrr_set_transcoder_timings() with HAS_VRR()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321135615.27338-1-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
- i915.enable_sagv module parameter (Ville)
- Correction to QGV related register addresses (Vinod)
- IPS debugfs per-crtc and new file for false_color (Ville)
- More clean-up and reorganization of Display code (Jani)
- DP DSC related fixes and improvements (Stanislav, Ankit, Suraj, Swati)
- Make utility pin asserts more accurate (Ville)
- Meteor Lake enabling (Daniele)
- High refresh rate PSR fixes (Jouni)
- Cursor and Plane chicken register fixes (Ville)
- Align the ADL-P TypeC sequences with hardware specification (Imre)
- Documentation build fixes and improvements to catch bugs earlier (Lee, Jani)
- PL1 power limit hwmon entry changed to use 0 as disabled state (Ashutosh)
- DP aux sync fix and improvements (Ville)
- DP MST fixes and w/a (Stanislav)
- Limit PXP drm-errors or warning on firmware API failures (Alan)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAmQu0TIACgkQ+mJfZA7r
E8osJwf+Pi3tvP1gvum4aVM2IgjA9fF1ZTwwFDqVNwJ2Sfzb93E0XOetoqd0AsEa
z6XYKN5N6P+dA1zLdtV21cmmI3V0iC7UEoZVba98n6Euabh0+7sDcS6o9Y7wDLqJ
DsDL02Vb2OMNjHce+w2lvbiLU52pWh9hVpB47bqS/vjTE9Q+C0Y2PoReyTca6o63
wmOXd1LSNfmaXHfeTRwQdWD7XlHtVmZmH0vn3BSd1ikB0nT7BJIIdc96fody19DI
67CLhQANhesp5si9JIqTWdxSgEibxFP9xDqfx3FOGJfhxWuOPSTs8hk/OjXM3zjr
2uSOnqxZ4a+nrSXy6pG4R4PqvG6ljg==
=Yqy1
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2023-04-06' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Fix DPT+shmem combo and add i915.enable_dpt modparam (Ville)
- i915.enable_sagv module parameter (Ville)
- Correction to QGV related register addresses (Vinod)
- IPS debugfs per-crtc and new file for false_color (Ville)
- More clean-up and reorganization of Display code (Jani)
- DP DSC related fixes and improvements (Stanislav, Ankit, Suraj, Swati)
- Make utility pin asserts more accurate (Ville)
- Meteor Lake enabling (Daniele)
- High refresh rate PSR fixes (Jouni)
- Cursor and Plane chicken register fixes (Ville)
- Align the ADL-P TypeC sequences with hardware specification (Imre)
- Documentation build fixes and improvements to catch bugs earlier (Lee, Jani)
- PL1 power limit hwmon entry changed to use 0 as disabled state (Ashutosh)
- DP aux sync fix and improvements (Ville)
- DP MST fixes and w/a (Stanislav)
- Limit PXP drm-errors or warning on firmware API failures (Alan)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZC7RR3Laet8ywHRo@intel.com
Include the device and connector information in the SCDC
debugs. Makes it easier to figure out who did what.
v2: Rely on connector->ddc (Maxime)
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Robert Foss <rfoss@kernel.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Emma Anholt <emma@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403223652.18848-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The encoder update_prepare()/complete() hooks were added to hold a
TC port link reference for all outputs in the atomic state around the
whole modeset enable sequence - thus locking the ports' TC mode - and
set the TBT/DP-alt PLL type corresponding to the current TC mode.
Since nothing depends on the PLL selection before/after then encoder's
pre_pll_enable/post_pll_disable hooks are called, the above steps can be
moved to these hooks, so do that and remove the
update_prepare()/complete() hooks.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-30-imre.deak@intel.com
Bspec requires disabling the DPLLs on TC ports before disconnecting the
port's PHY. Add a post_pll_disable encoder hook and move the call to
disconnect the port's PHY from the post_disable hook to the new hook.
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230323142035.1432621-28-imre.deak@intel.com
For clarity factor out the function to determine if there are active
links on a TC port. This prepares for the next patch also checking the
port's PLL type.
While at it pass crtc_state to intel_tc_port_sanitize_mode(), and check
hw.active in that, instead of the deprecated crtc->active flag.
v2: Check crtc_state->hw.active instead of crtc->active. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-2-imre.deak@intel.com
Add an encoder hook, which can be called on enabled TC ports to
determine if the port uses a TBT or a non-TBT PLL. An upcoming patch
will use this to sanity check active TC port's PHY state wrt. the PLL
type used by the port.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-13-imre.deak@intel.com
Since an HDMI output can only be enabled in legacy mode on TC ports,
assume that VBT is wrong and the port is legacy if VBT says the port is
non-legacy and has HDMI. If VBT says to enable DP as well leave the
non-legacy flag enabled, relying on the flag getting fixed up based on
the HPD status during sink detection.
v2: Fix the legacy port flag only if DP is not enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-1-imre.deak@intel.com
Enable SDP error detection configuration, this will set CRC16 in
128b/132b link layer.
For Display version 13 a hardware bit31 in register VIDEO_DIP_CTL is
added to enable/disable SDP CRC applicable for DP2.0 only, but the
default value of this bit will enable CRC16 in 128b/132b hence
skipping this write.
Corrective actions on SDP corruption is yet to be defined.
v2: Moved the CRC enable to link training init(Jani N)
v3: Moved crc enable to ddi pre enable <Jani N>
v4: Separate function for SDP CRC16 (Jani N)
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302081532.765821-3-arun.r.murthy@intel.com
AFAICS Bspec has never asked us to switch to TPS1 when *disabling*
DP_TP_CTL. Let's stop doing that in case it confuses something.
We do have to switch before we *enable* DP_TP_CTL, but that
is already being handled correctly.
v2: Do the same for FDI
v3: Rebase
Reviewed-by: Imre Deak <imre.deak@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230308212627.7601-1-ville.syrjala@linux.intel.com
SKL doesn't have any north DE hotplug stuff. Currently we're
trying to read DDI A live state from the BDW north DE bit,
instead of the approproate south DE bit. Fix it.
And for good measure clear the pointer to the north hpd
pin array, so that we'll actually notice if some other
place is also using the wrong thing.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302161013.29213-3-ville.syrjala@linux.intel.com
We'll need dig_port->connected() to be there for a HPD live
state check during eDP connector probing. Reorder intel_ddi_init()
accordingly. g4x_dp_init() is already fine.
v2: Fix comment style while at it
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230302161013.29213-2-ville.syrjala@linux.intel.com
Use an early return to get rid of the extra indentation level
in intel_ddi_{enable,disable}_transcoder_clock().
Also unify the platform handling in between the two while at
it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Restructure intel_bios_port_aux_ch() to resemble the ddc_pin
counterpart, where the intel_bios.c stuff only deals with the
child device definition, and the platform default will come from
elsewhere.
This requires the introduction of AUX_CH_NONE as the value 0
is already taken to mean AUX_CH_A.
v2: Sort includes alphabetically (Ankit)
vCould we ask them to do a BIOS fix for all of them so that
we wouldn't keep getting these bug reports for each model
separately?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216231312.32664-1-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Switch a lot of the intel_bios_foo() stuff to just accept the
devdata (VBT child device info) directly, instead of taking
detours via vbt.ports[].
Also unify the function naming scheme.
v2: Drop the redundant "encoder" from the dp/hdmi specific functions
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230216000425.32216-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently intel_bios_port_aux_ch() digs out the devdata
(VBT child device info) from the vbt.ports[] array. We
need to get rid of that, so just pass in the correct
encoder->devdata (now that we have it also for g4x+ ports)
directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The sole user of intel_bios_is_lane_reversal_needed() has
the devdata already located, so pass it in directly instead
of digging it again from vbt.ports[].
And rename the function to follow the common pattern for
these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We always have encoder->devdata available on the platforms
that can have LSPCON. So let's start looking there instead
of digging it out from vbt.ports[].
And let's rename the function to fit the common pattern
for these things.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230208015508.24824-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Read out the ELD from the hardware buffer, or from our stashed
copy for the audio component, so that we can hook up the state
checker to validate it.
v2: Deal with the platforms using acomp
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-7-ville.syrjala@linux.intel.com
For Gen12+ wait for 1ms for Combo Phy and 3ms for TC Phy for
DDI_BUF_CTL to be active for TC phy. (Bspec:49190)
v2: Minor refactoring for better readability.
v3: Rebased and retained the order of checking platforms. (Imre)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221207145436.1510625-1-ankit.k.nautiyal@intel.com
On mtl it looks like disabling VRR after the transcoder has
been disabled can cause the pipe/transcoder to get stuck
when re-enabled in non-vrr mode. Reversing the order seems to
help.
Bspec is extremely confused about the VRR enable/disable sequence
anyway, and this now more closely matches the non-modeset VRR
sequence, whereas the full modeset sequence still claims that
the original order is fine. But since we eventually want to toggle
VRR without a full modeset anyway this seems like the better order
to follow.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221202134412.21943-4-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Enable the SDP split configuration for DP2.0.
v2: Move the register handling out of compute config function (JaniN)
v3: Patch styling and register access based on platform support (JaniN)
v4: Rebased
v5: Use unconditional clear bit in intel_de_rmw (Jani Nikula)
Bspec: 67768
Signed-off-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221121150718.1117628-1-vinod.govindapillai@intel.com
MTL+ requires the AUX_IO power for the main link only on eDP, so don't
enable it in other cases.
v2:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-10-imre.deak@intel.com
Factor out functions to get/put the AUX_IO power domain for the main
link on DDI ports.
While at it clarify the corresponding code comment.
No functional change.
v2:
- s/(get/put)_aux_power_for_main_link/main_link_aux_power_domain_(get/put)
(Jani)
- Clarify in the code comment that AUX_IO is needed only by TypeC besides
eDP/PSR.
v3:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
v4:
- Don't call fetch_and_zero() with side-effect during variable
declaration. (Ville)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-9-imre.deak@intel.com
Starting with TGL eDP is supported on ports B+ (besides port A), so make
sure DC states are not blocked on any such ports. For this add an
AUX_IO_<port> power domain for each port with eDP support. These domains
similarly to AUX_IO_A enable only the AUX_IO_<port> power well for an
enabled port, whereas the existing AUX_<port> domains enable both the
AUX_IO_<port> and the DC_OFF power wells as required by DP AUX transfers.
v2: (Ville)
- Split the change using AUX vs. AUX_IO on port A to a separate patch.
- Select AUX_IO vs. AUX based on crtc_state->has_psr instead of
is_edp().
v3:
- Rebased on checking intel_encoder_can_psr() instead of crtc->has_psr.
v4:
- Fix warn in intel_display_power_aux_io_domain(). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-6-imre.deak@intel.com
Use the AUX_IO_A display power domain only for eDP on port A where PSR
is also supported. This is the case where DC states need to be enabled
while the output is enabled - ensured by AUX_IO_A domain not enabling
the DC_OFF power well. Otherwise port A can be treated the same way as
other ports with an external DP output: using the AUX_<port> domain
which disables the unrequired DC states.
This change prepares for the next patch enabling DC states on all ports
supporting eDP/PSR besides port A.
v2:
- Check the encoder PSR capability instead of PSR being enabled in the
crtc_state, as the latter can be changed with a fastset.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221114122251.21327-5-imre.deak@intel.com
The HTI or HDPORT handling is sprinkled around. Centralize to one place.
Add a note about how subtle the mapping from HDPORT_STATE register to
dpll mask actually is.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221109144209.3624739-1-jani.nikula@intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
Not all Dekel PHY registers have a lane instance, so having to specify
this when using them is awkward. It makes more sense to define each PHY
register with its full internal PHY offset where bits 15:12 is the lane
for lane-instanced PHY registers and just a register bank index for other
PHY registers. This way lane-instanced registers can be referred to with
the (tc_port, lane) parameters, while other registers just with a tc_port
parameter.
An additional benefit of this change is to prevent passing a Dekel
register to a generic MMIO access function or vice versa.
v2:
- Fix parameter reuse in the DKL_REG_MMIO definition.
v3:
- Rebase on latest patchset version.
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-3-imre.deak@intel.com
Move the TypeC DKL PHY register definitions to intel_dkl_phy_regs.h.
No functional changes.
v2:
- Move the definitions to a new intel_dkl_phy_regs.h file. (Jani).
v3:
- Rebase on latest patchset version.
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-2-imre.deak@intel.com
An upcoming patch moves the DKL PHY register definitions to
intel_dkl_phy_regs.h, so for consistency rename intel_tc_phy_regs.h
containing only MG PHY register definitions to intel_mg_phy_regs.h.
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025102644.2123988-3-imre.deak@intel.com
Accessing the TypeC DKL PHY registers during modeset-commit,
-verification, DP link-retraining and AUX power well toggling is racy
due to these code paths being concurrent and the PHY register bank
selection register (HIP_INDEX_REG) being shared between PHY instances
(aka TC ports) and the bank selection being not atomic wrt. the actual
PHY register access.
Add the required locking around each PHY register bank selection->
register access sequence.
Kudos to Ville for noticing the race conditions.
v2:
- Add the DKL PHY register accessors to intel_dkl_phy.[ch]. (Jani)
- Make the DKL_REG_TC_PORT macro independent of PHY internals.
- Move initing the DKL PHY lock to a more logical place.
v3:
- Fix parameter reuse in the DKL_REG_TC_PORT definition.
- Document the usage of phy_lock.
v4:
- Fix adding TC_PORT_1 offset in the DKL_REG_TC_PORT definition.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221025114457.2191004-1-imre.deak@intel.com
During system resume DP MST requires AUX to be working already before
the HW state readout of the given encoder. Since AUX requires the
encoder/PHY TypeC mode to be initialized, which atm only happens during
HW state readout, these AUX transfers can change the TypeC mode
incorrectly (disconnecting the PHY for an enabled encoder) and trigger
the state check WARNs in intel_tc_port_sanitize().
Fix this by initializing the TypeC mode earlier both during driver
loading and system resume and making sure that the mode can't change
until the encoder's state is read out. While at it add the missing
DocBook comments and rename
intel_tc_port_sanitize()->intel_tc_port_sanitize_mode() for consistency.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922172148.2913088-1-imre.deak@intel.com
We always allocate two DPLLs (TC and TBT) for TC ports. This
is because we can't know ahead of time wherher we need to put
the PHY into DP-Alt or TBT mode.
However during readout we can obviously only read out the state
of the DPLL that the port is actually using. Thus the state after
readout will not have both DPLLs populated.
We run into problems if during readout the TC port is in DP-Alt
mode, but we then perform a modeset on the port without going
through the full .compute_config() machinery, and during said
modeset the port cannot be switched back into DP-Alt mode and
we need to take the TBT fallback path. Such a modeset can
happen eg. due to cdclk reprogramming.
This wasn't a problem earlier because we did all the DPLL
calculations much later in the modeset. So even if flagged
a modeset very late we'd still have gone through the DPLL
calculations. But now all the DPLL calculations happen much
earlier and so we need to deal with it, or else we'll attempt
a modeset without a DPLL.
To guarantee that we always have both DPLLs fully cal/ulated
for TC ports force a full modeset computation during the
initial commit.
v2: Avoid bitwise operation on bool (Jani)
Call the return variable 'fastset' to convey its meaning
Reported-by: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: b000abd3b3 ("drm/i915: Do .crtc_compute_clock() earlier")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220922191236.4194-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Make sure the TypeC PHY ownership flag is not getting reset during
an HDMI modeset on the given port. Besides the WARN this triggered, it
didn't cause other issues, since for TypeC legacy mode setting the
PHY ownership flag is optional (there is no other user of the PHY
besides display).
Reported-and-tested-by: Shawn C Lee <shawn.c.lee@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220726134313.1484763-1-imre.deak@intel.com
Starting with TGL the disabling order of HDMI transcoder clock vs. DDI
BUF has swapped, fix this. There hasn't been any issues seen related to
this, but let's follow the spec.
Reported-by: Sandeep K Lakkakula <sandeep.k.lakkakula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220617112807.1586621-1-imre.deak@intel.com
Extract intel_crtc_dotclock() from ddi_dotclock_get(). We'll reuse
this during state computation in order to determine the actual final
dotclcok after the DPLL computation has been done (which may not give
us the exact same port_clock that we fed in).
v2: Add the prototype
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220504123350.13235-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Split out audio registers to a header of its own to reduce the size of
i915_reg.h.
TODO: Remove direct audio register access from intel_ddi.c. However,
unification of audio get config is cumbersome due to the audio enable
bit being in the DP or HDMI registers on older platforms.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220602094542.1386151-1-jani.nikula@intel.com
Avoid bringing the entire machine down even if there's a bug that
shouldn't happen, but won't corrupt the system either. Log them loudly
and limp on.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531162527.1062319-1-jani.nikula@intel.com
We have the same "override eDP VBT bpp with the current bpp" code
duplciated in two places. Extract it to a helper function.
TODO: Having this in .get_config() is pretty ugly. Should probably
try to move it somewhere else (setup_hw_state()/etc.)...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
drm/i915 feature pull #2 for v5.19:
Features and functionality:
- Add first set of DG2 PCI IDs for "motherboard down" designs (Matt Roper)
- Add initial RPL-P PCI IDs as ADL-P subplatform (Matt Atwood)
Refactoring and cleanups:
- Power well refactoring and cleanup (Imre)
- GVT-g refactor and mdev API cleanup (Christoph, Jason, Zhi)
- DPLL refactoring and cleanup (Ville)
- VBT panel specific data parsing cleanup (Ville)
- Use drm_mode_init() for on-stack modes (Ville)
Fixes:
- Fix PSR state pipe A/B confusion by clearing more state on disable (José)
- Fix FIFO underruns caused by not taking DRAM channel into account (Vinod)
- Fix FBC flicker on display 11+ by enabling a workaround (José)
- Fix VBT seamless DRRS min refresh rate check (Ville)
- Fix panel type assumption on bogus VBT data (Ville)
- Fix panel data parsing for VBT that misses panel data pointers block (Ville)
- Fix spurious AUX timeout/hotplug handling on LTTPR links (Imre)
Merges:
- Backmerge drm-next (Jani)
- GVT changes (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87bkwbkkdo.fsf@intel.com
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Atm the port -> DDI and AUX power domain mapping is specified by relying
on the aliasing of the platform specific intel_display_power_domain enum
values. For instance D12+ platforms refer to the 'D' port and power
domain instances, which doesn't match the bspec terminology, on these
platforms the corresponding port is TC1. To make it clear what
port/domain the code refers to add a mapping between them which matches
the bspec terms on different display versions.
This also allows for removing the aliasing in enum values in a follow-up
patch.
v2: Add the functions to intel_display_power.c, use
intel_display_power_ prefix.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414210657.1785773-14-imre.deak@intel.com
When the PHY fails on calibration we were previously skipping the ddi
initialization. However the driver is not really prepared for that,
ultimately leading to a NULL pointer dereference:
[ 75.748348] i915 0000:03:00.0: [drm:intel_modeset_init_nogem [i915]] SNPS PHY A failed to calibrate; output will not be used.
...
[ 75.750336] i915 0000:03:00.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: enabled
...
( no DDI A/PHY A )
[ 75.753080] i915 0000:03:00.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:235:DDI B/PHY B] hw state readout: disabled, pipe A
[ 75.753164] i915 0000:03:00.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:245:DDI C/PHY C] hw state readout: disabled, pipe A
...
[ 75.754425] i915 0000:03:00.0: [drm] *ERROR* crtc 80: Can't calculate constants, dotclock = 0!
[ 75.765558] i915 0000:03:00.0: drm_WARN_ON_ONCE(drm_drv_uses_atomic_modeset(dev))
[ 75.765569] WARNING: CPU: 5 PID: 1759 at drivers/gpu/drm/drm_vblank.c:728 drm_crtc_vblank_helper_get_vblank_timestamp_internal+0x347/0x360
...
[ 75.781230] BUG: kernel NULL pointer dereference, address: 000000000000007c
[ 75.788198] #PF: supervisor read access in kernel mode
[ 75.793347] #PF: error_code(0x0000) - not-present page
[ 75.798480] PGD 0 P4D 0
[ 75.801019] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 75.805377] CPU: 5 PID: 1759 Comm: modprobe Tainted: G W 5.18.0-rc1-demarchi+ #199
[ 75.827613] RIP: 0010:icl_aux_power_well_disable+0x3b/0x200 [i915]
[ 75.833890] Code: 83 ec 30 65 48 8b 04 25 28 00 00 00 48 89 44 24 28 48 8b 06 0f b6 70 1c f6 40 20 04 8d 56 fa 0f 45 f2 e8 88 bd ff ff 48 89 ef <8b> 70 7c e8 ed 67 ff ff 48 89 ef 89 c6 e8 73 67 ff ff 84 c0 75 0a
[ 75.852629] RSP: 0018:ffffc90003a7fb30 EFLAGS: 00010246
[ 75.857852] RAX: 0000000000000000 RBX: ffff8881145e8f10 RCX: 0000000000000000
[ 75.864978] RDX: ffff888115220840 RSI: 0000000000000000 RDI: ffff888115220000
[ 75.872106] RBP: ffff888115220000 R08: ffff88888effffe8 R09: 00000000fffdffff
[ 75.879234] R10: ffff88888e200000 R11: ffff88888ed00000 R12: ffff8881145e8f10
[ 75.886363] R13: 0000000000000001 R14: ffff888115223240 R15: 0000000000000000
[ 75.893490] FS: 00007ff6e753a740(0000) GS:ffff88888f680000(0000) knlGS:0000000000000000
[ 75.901573] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 75.907313] CR2: 000000000000007c CR3: 00000001216a6001 CR4: 0000000000770ee0
[ 75.914446] PKRU: 55555554
[ 75.917153] Call Trace:
[ 75.919603] <TASK>
[ 75.921709] intel_power_domains_sanitize_state+0x88/0xb0 [i915]
[ 75.927814] intel_modeset_init_nogem+0x317/0xef0 [i915]
[ 75.933205] i915_driver_probe+0x5f6/0xdf0 [i915]
[ 75.937976] i915_pci_probe+0x51/0x1d0 [i915]
We skip the initialization of PHY A, but later we try to find out what
is the phy for that power well and dereference dig_port, which is NULL.
Failing the PHY calibration could be left as a warning or error, like it
was before commit b4eb76d82a ("drm/i915/dg2: Skip output init on PHY
calibration failure"). However that often fails for outputs not being
used, which would make the warning/error appear on systems that have no
visible issues. Anyway, there is still a need to fix those failures,
but that is left for later.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220410061537.4187383-1-lucas.demarchi@intel.com
Let's just do a full DRRS disable/enable across all pipe updates.
This guarantees that the DRRS work doesn't interfere with anything
while the atomic commit is busy reprogramming the pipe.
Needed so that we can start reprogramming M/N seamlessly during
fastsets whenever possible. Also avoids the pre-bdw DRRS PIPECONF
rmw racing with the potential PIPECONF write from the atomic
commit (eg. due to GAMMA_MODE changes).
v2: Include has_drrs in state dump (José)
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220315213944.17132-1-ville.syrjala@linux.intel.com
No reason to keep the DRRS enable/disable hidden insider the encoder
hooks. Let's just move them all the way up into platform independent
code so that all platforms get to use them. These are nops when
the state computation doesn't think DRRS is possible.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-14-ville.syrjala@linux.intel.com
Ger rid of one more ugly crtc->config usage by storing the DRRS
state under intel_crtc. intel_drrs_enable() copies what it needs
from the crtc state, after which DRRS can be blissfully ignorant
of anything going on around it.
This also lets multiple pipes do DRRS simultanously and entirely
independently.
v2: Split out some stuff (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Remove the local enabledisable() implementation and adopt the
str_enable_disable() from linux/string_helpers.h.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225234631.3725943-2-lucas.demarchi@intel.com
If one of our PHYs fails to complete calibration, we should skip the
general initialization of the corresponding output. Most likely this is
going to happen on outputs that don't actually exist on the board; in
theory we should have already decided to skip this output based on the
VBT, but we can't always rely on the VBT being accurate.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223165421.3949883-1-matthew.d.roper@intel.com
Add display workaround # 1309179469 , which fixes a PHY hang when
switching from TBT mode to DP-alt/legacy mode. The workaround also
requires an IFWI/PHY firmware change, before that this change has no
effect (the DKL_PCS_DW5/SOFTRESET flag is always cleared).
HSDES: 18018237866
HSDES: 16014473319
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220218122611.767974-1-imre.deak@intel.com
Get rid of the inflexible bigjoiner_linked_crtc pointer thing
and just track things as a bitmask of pipes instead. We can
also nuke the bigjoiner_slave boolean as the role of the pipe
can be determined from its position in the bitmask.
It might be possible to nuke the bigjoiner boolean as well
if we make encoder.compute_config() do the bitmask assignment
directly for the master pipe. But for now I left that alone so
that encoer.compute_config() will just flag the state as needing
bigjoiner, and the intel_atomic_check_bigjoiner() is still
responsible for determining the bitmask. But that may have to change
as the encoder may be in the best position to determine how
exactly we should populate the bitmask.
Most places that just looked at the single bigjoiner_linked_crtc
now iterate over the whole bitmask, eliminating the singular
slave pipe assumption.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203183823.22890-11-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Instead of passing in the whole crtc state let's pass in just
the bits of state we need. This will help with the DRRS code
which shouldn't really be accessing the atomic state stuff directly
as it gets called outside the normal atomic flows.
v2: Fix set_m1_n1 vs. set_m2_n2 fumble for i9xx (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Make things a bit more explicit by splitting
intel_cpu_transcoder_set_m_n() into separate variants for M1/N1 vs.
M2/N2. Makes the DRRS M/N programming at least more obvious.
Note that for the MST and DRRS cases we don't need to call the
M2/N2 variant at all since the transcoders that support those
do not have the M2/N2 registers.
Same could be said for i9xx_crtc_enable() but I want to do a
higher level code sharing between that valleyview_crtc_enable()
later in which case we do need the M2/N2 variant. This is also
why I keep the transcoder_has_m2_n2() in intel_cpu_transcoder_set_m2_n2()
so the caller doesn't have necessarily care what the chosen
transcoder supports.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I want to make a clean split betwen the CPU vs. PCH transcoder
programming. To that end eliminate intel_dp_set_m_n() and just
call the individual CPU/PCH transcoder functions directly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220128103757.22461-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Lift the dsc/joiner enable up from the wonky places where it
currently sits (ddi .pre_enable() or icl_ddi_bigjoiner_pre_enable())
into hsw_crtc_enable() where we write the other per-pipe stuff
as well. Makes the transcoder vs. pipe split less confusing.
For DSI this results in slight reordering between the dsc/joiner
enable vs. transcoder timings setup, but I can't really think
why that should cause any issues since the transcoder isn't yet
enabled at that point.
v2: Take care of dsi (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125063937.7003-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
dg2_ddi_pre_enable_dp() has outlived its usefulness so eliminate
it.
The one thing that tgl_ddi_pre_enable_dp() is missing that we
need is intel_ddi_config_transcoder_dp2(). So we'll bring that
over.
tgl_ddi_pre_enable_dp() does also have a few things that
dg2_ddi_pre_enable_dp() didn't have:
- icl_program_mg_dp_mode() -> nop due to intel_phy_is_tc()==false on DG2
- intel_ddi_power_up_lanes() -> nop due to intel_phy_is_combo()==false on DG2
- intel_ddi_mso_configure() -> only matters for MSO panels
Another slight difference is that dg2_ddi_pre_enable_dp() was
missing a bigjoiner check around intel_dsc_enable(), which
tgl_ddi_pre_enable_dp() does have.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220119122150.12941-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
TC voltage swing programming sequence was updated with a new step.
BSpec: 54956
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220113174826.50272-1-jose.souza@intel.com
Registers representing the MG/DKL TC PHYs (including the TC DPLLs which
exist inside the PHY) are only needed in a couple files and on specific
platforms; let's keep them separate from the general register pool.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220111051600.3429104-11-matthew.d.roper@intel.com
Add support for eDP panels with a built-in privacy screen using the
new drm_privacy_screen class.
Changes in v3:
- Move drm_privacy_screen_get() call to intel_ddi_init_dp_connector()
Changes in v2:
- Call drm_connector_update_privacy_screen() from
intel_enable_ddi_dp() / intel_ddi_update_pipe_dp() instead of adding a
for_each_new_connector_in_state() loop to intel_atomic_commit_tail()
- Move the probe-deferral check to the intel_modeset_probe_defer() helper
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005202322.700909-11-hdegoede@redhat.com
Currently we're only calling intel_update_active_dpll() for the
bigjoiner master pipe but not for the slave. With TC ports this
leads to the two pipes end up trying to use different PLLs
(TC vs. TBT). What's worse we're enabling the PLL that didn't get
intel_update_active_dpll() called on it at the spot where we
need the clocks turned on. So we turn on the wrong PLL and the
DDI is now trying to source its clock from the other PLL which is
still disabled. Naturally that doesn't end so well and the DDI
fails to start up.
The state checker also gets a bit unhappy (which is a good thing)
when it notices that one of the pipes was using the wrong PLL.
Let's fix this by remembering to call intel_update_active_dpll()
for both pipes. That should get the correct PLL turned on when
we need it, and the state checker should also be happy.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4434
Fixes: e12d6218fd ("drm/i915: Reduce bigjoiner special casing")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105212156.5697-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Prepare for per-lane drive settings by querying the desired vswing
level per-lane.
Note that the code only does two loops, with each one writing the
levels for two TX lanes. The register offsets also look a bit funny
because each time through the loop we write to the exact same
register offsets. The crucial bit is the HIP_INDEX_REG
write that steers the same mmio window into different places.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006204937.30774-11-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Prepare for per-lane drive settings by querying the desired vswing
level per-lane.
Note that the code only does two loops, with each one writing the
levels for two TX lanes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006204937.30774-10-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Looks like our VBIOS/GOP generally fail to turn the DP dual mode adater
TMDS output buffers back on after a reboot. This leads to a black screen
after reboot if we turned the TMDS output buffers off prior to reboot.
And if i915 decides to do a fastboot the black screen will persist even
after i915 takes over.
Apparently this has been a problem ever since commit b2ccb822d3 ("drm/i915:
Enable/disable TMDS output buffers in DP++ adaptor as needed") if one
rebooted while the display was turned off. And things became worse with
commit fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
since now we always turn the display off before a reboot.
This was reported on a RKL, but I confirmed the same behaviour on my
SNB as well. So looks pretty universal.
Let's fix this by explicitly turning the TMDS output buffers back on
in the encoder->shutdown() hook. Note that this gets called after irqs
have been disabled, so the i2c communication with the DP dual mode
adapter has to be performed via polling (which the gmbus code is
perfectly happy to do for us).
We also need a bit of care in handling DDI encoders which may or may
not be set up for HDMI output. Specifically ddc_pin will not be
populated for a DP only DDI encoder, in which case we don't want to
call intel_gmbus_get_adapter(). We can handle that by simply doing
the dual mode adapter type check before calling
intel_gmbus_get_adapter().
Cc: <stable@vger.kernel.org> # v5.11+
Fixes: fe0f1e3bfd ("drm/i915: Shut down displays gracefully on reboot")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4371
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029191802.18448-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Try to make bigjoiner pipes less special.
The main things here are that each pipe now does full
clock computation/readout with its own shared_dpll reference.
Also every pipe's cpu_transcoder always points correctly
at the master transcoder.
Due to the above changes state readout is now complete
and all the related hacks can go away. The actual modeset
sequence code is still a mess, but I think in order to clean
that up properly we're probably going to have to redesign
the modeset logic to treat transcoders vs. pipes separately.
That is going to require significant amounts of work.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-9-ville.syrjala@linux.intel.com
The PPS SDP is fed into the transcoder whereas the DSC
block is (or at least can be) per pipe. Let's split these
into two distinct operations in an effort to untagle the
bigjoiner mess where we have two pipes feeding a single
transcoder.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-7-ville.syrjala@linux.intel.com
Disabling planes in the middle of the modeset seuqnece does not make
sense since userspace can anyway disable planes before the modeset
even starts. So when the modeset seuqence starts the set of enabled
planes is entirely arbitrary. Trying to sprinkle the plane disabling
into the modeset sequence just means more randomness and potential
for hard to reproduce bugs.
So it makes most sense to just disable all planes first so that the
rest of the modeset sequence remains identical regardless of which
planes happen to be enabled by userspace at the time.
This reverts commit 84030adb9e.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reanme intel_ddi_fdi_post_disable() to hsw_fdi_disable() and
relocate it next to all the other code dealing with FDI_RX.
intel_ddi.c has now been cleansed of FDI_RX.
In order to avoid exposing intel_disable_ddi_buf() outside
intel_ddi.c we can just open code the DDI_BUF_CTL write. The
enable side already has all that stuff open coded so
this actually is more symmetric. But we do need to remeber
to bring the intel_wait_ddi_buf_idle() call over from
inside intel_disable_ddi_buf().
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-9-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Move the lpt_get_iclkip() call from hsw_crt_get_config()
since that's where we have the lpt_program_iclkip() call
as well.
Tehcnically this isn't perhaps quite right since iCLKIP
is providing the CRT dotclock. So one can argue all of
it should be directly in intel_crt.c. But since the CRT
port is the only one on the PCH sticking it all into the
PCH code seems OK.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-7-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
DKL_TX_LOADGEN_SHARING_PMD_DISABLE doesn't even seem to exist,
also the spec says to skip all loadgen stuff.
The code was dead anyway since it wasn't actually writing the value
anywhere.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006204937.30774-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The 128b/132b channel coding link training uses more straightforward TX
FFE preset values. Reuse voltage tries and max vswing for retry logic.
The delays for 128b/132b are still all wrong, but this is regardless a
step forward.
v2: Fix UHBR rate checks, use intel_dp_is_uhbr() helper
v3:
- Rebase
- Modify intel_dp_adjust_request_changed() and
intel_dp_link_max_vswing_reached() to take 128b/132b into
account. (Ville)
v4:
- Train request printing for TX FFE (Ville)
- Log 8b/10b vs. 128b/132b (Ville)
- Add helper for per-lane max vswing / tx ffe (Ville)
- Name functions with tx_ffe/vswing instead of 128b132b/8b10b
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211011182144.22074-2-jani.nikula@intel.com
The "digi_port" pointer can't be NULL and we have already dereferenced
it so checking for NULL is not necessary. Delete the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004103737.GC25015@kili
In order to have per-lane drive settings we need intel_ddi_level()
to accept the lane as a parameter. That is, the eventual goal is to
call intel_ddi_level() once for each lane. For now we just pass in
a hardcoded 0 and use the same settings for every lane. Ie. no
change in behaviour yet.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-9-ville.syrjala@linux.intel.com
Since intel_ddi_level() now looks at the buf_trans table there's
no point in having intel_ddi_hdmi_num_entries() around. Just
roll the necessary bits of locic into
intel_ddi_hdmi_level()/intel_ddi_level().
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-8-ville.syrjala@linux.intel.com
All callers of intel_ddi_level() duplicate the check+WARN
to make sure the returned level is actually present in the
appropriate buf_trans table. Let's push that stuff into
intel_ddi_level() so the callers don't have to worry about it.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-7-ville.syrjala@linux.intel.com
Currently .set_signal_levels() is only used by encoders in DP mode.
For most modern platforms there is no essential difference between
DP and HDMI, and both codepaths just end up calling the same function
under the hood. Let's get remove the need for that extra indirection
by moving .set_signal_levels() into the encoder from intel_dp.
Since we already plumb the crtc_state/etc. into .set_signal_levels()
the code will do the right thing for both DP and HDMI.
HSW/BDW/SKL are the only platforms that need a bit of care on
account of having to preload the hardware buf_trans register
with the full set of values. So we must still remember to call
hsw_prepare_{dp,hdmi}_ddi_buffers() to do said preloading, and
.set_signal_levels() will just end up selecting the correct entry
for DP, and also setting up the iboost magic for both DP and HDMI.
Note that previously on HSW/BDW/SKL we did write to DDI_BUF_CTL to
select the correct entry until link training started, now that we
call .set_signal_levels() already from hsw_ddi_pre_enable_dp() that
is no longer the case. But it's all safe now that the
intel_ddi_init_dp_buf_reg() call was hoisted up and it no longer
sets up the DDI_BUF_CTL_ENABLE bit (that is still deferred until
link training).
v2: Rebase due to has_{iboost,buf_trans_select}()
Add some notes about the DDI_BUF_CTL situation on HSW/BDW/SKL (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-4-ville.syrjala@linux.intel.com
Add a small helper to determine if DDI_BUF_CTL uses the
DDI_BUF_TRANS_SELECT field, and whether we have the
accompanying DDI_BUF_TRANS table in the hardware.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211001130107.1746-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
I want intel_dp->DP to be fully populated by the time the
initial vswing programming happens. To that end move the
intel_ddi_init_dp_buf_reg() call to an earlier spot.
Additionally we don't want intel_ddi_init_dp_buf_reg() to
set DDI_BUF_CTL_ENABLE since the port should only get enabled
at the start of link training (see intel_ddi_prepare_link_retrain()).
So any earlier write to the register should not set the enable bit.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930134310.31669-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
So far TC-cold was blocked only for the duration of TypeC mode resets.
The DP-alt and legacy modes require TC-cold to be blocked also whenever
the port is in use (AUX transfers, enable modeset), and this was ensured
by the held PHY ownership flag. On ADL-P this doesn't work, since the
PHY ownership flag is in a register backed by the PW#2 power well.
Whenever this power well is disabled the ownership flag is cleared by
the HW under the driver.
The only way to cleanly release and re-acquire the PHY ownership flag
and also allow for power saving (by disabling the display power wells
and reaching DC5/6 states) is to hold the TC-cold blocking power domains
while the PHY is connected and disconnect/reconnect the PHY on-demand
around AUX transfers and modeset enable/disables. Let's do that,
disconnecting a PHY with a 1 sec delay after it becomes idle. For
consistency do this on all platforms and TypeC modes.
v2: Add tc_mode!=disconnected and phy_is_owned asserts to
__intel_tc_port_lock().
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-6-imre.deak@intel.com
Instead of directly accessing the TypeC port internal struct members,
add/use helpers to retrieve the corresponding properties.
No functional change.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210921002313.1132357-6-imre.deak@intel.com
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
PSR always had a requirement to only be enabled if there is active
planes but not following that never caused any issues.
But that changes in Alderlake-P, leaving PSR enabled without
active planes causes transcoder/port underruns.
Similar behavior was fixed during the pipe disable sequence by
commit 84030adb9e ("drm/i915/display: Disable audio, DRRS and PSR before planes").
intel_dp_compute_psr_vsc_sdp() had to move from
intel_psr_enable_locked() to intel_psr_compute_config() because we
need to be able to disable/enable PSR from atomic states without
connector and encoder state.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922215242.66683-3-jose.souza@intel.com
128b/132b has a separate transcoder DDI mode, which also requires the
MST transport select to be set. Note that we'll use DP MST also for
single-stream 128b/132b.
Having the FDI and 128b/132b modes share the register mode value
complicates things a bit.
v2:
- Use HAS_DP20 abstraction for 128b/132b mode (Ville)
- Use intel_dp_is_uhbr() helper
Bspec: 50493
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/279bfbd979e0256fae13a5231e07e2f4fb665c07.1631191763.git.jani.nikula@intel.com
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We had a mix of intel_edp_drrs_*(), intel_dp_drrs_*() and
intel_dp_set_drrs_state(), so properly renaming all functions to
keep the same pattern.
While at it, also dropping intel_dp_set_drrs_state from the
documentation as it is a static function.
v3:
- dropping documentation style comment in static function
(intel_drrs_set_state)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-3-jose.souza@intel.com
intel_dp.c is a 5k lines monster, so moving DRRS out of it to reduce
some lines from it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-2-jose.souza@intel.com
We use encoder->get_buf_trans() in many places, for example
intel_ddi_dp_voltage_max(), and the hook was set to some old platform's
function for DG2 SNPS PHY. Convert SNPS PHY to use the same translation
mechanisms as everything else.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210813115151.19290-2-jani.nikula@intel.com
ADL-P supports stream splitter on pipe B in addition to pipe A. Update
the sanity check in intel_ddi_mso_get_config() to reflect this, and
remove the check in intel_ddi_mso_configure() as redundant with
encoder->pipe_mask. Abstract the splitter pipe mask to a single point of
truth while at it to avoid similar mistakes in the future.
Fixes: 7bc188cc2c ("drm/i915/adl_p: enable MSO on pipe B")
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Tested-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812132354.10885-1-jani.nikula@intel.com
DG1 and XE_PLD platforms has Audio MMIO/VERBS lies in PG0 power
well. Adjusting the power domain accordingly to
POWER_DOMAIN_AUDIO_MMIO for audio detection and
POWER_DOMAIN_AUDIO_PLAYBACK for audio playback.
While doing this it requires to use POWER_DOMAIN_AUDIO_MMIO
power domain instead of POWER_DOMAIN_AUDIO in crtc power domain mask
and POWER_DOMAIN_AUDIO_PLAYBACK with intel_display_power_{get, put}
to enable/disable display audio codec power.
It will save the power in use cases when DP/HDMI connectors
configured with PIPE_A without any audio playback.
v1: Changes since RFC
- changed power domain names. [Imre]
- Removed TC{3,6}, AUX_USBC{3,6} and TBT from DG1
power well and PW_3 power domains. [Imre]
- Fixed the order of powe wells , power domains and its
registration. [Imre]
v2:
- Not allowe DC states when AUDIO_MMIO domain enabled. [Imre]
v3:
- Squashes the commits of series to avoid build failure.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
[Fix typo in commit message and in AUDIO_PLAYBACK domain name]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729121858.16897-2-anshuman.gupta@intel.com
The only real platform with DISPLAY_VER == 10 is GLK. We don't need to
handle CNL explicitly in intel_ddi.c.
Remove code and rename functions/macros accordingly to use ICL prefix.
There's one leftover reference to cnl that comes from the struct
intel_ddi_buf_trans. This will be renamed later when we get rid of the
additional CNL tables.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728215946.1573015-7-lucas.demarchi@intel.com
DG2 has some changes to the expected modesetting sequences when compared
to gen12. Adjust our driver logic accordingly. Although the DP
sequence is pretty similar to TGL's, there are some steps that change,
so let's split the handling for that out into a separate function.
v2:
- Switch wait_for_us() -> _wait_for() so that we can parameterize the
timeout rather than duplicating the macro call. (Jani)
Bspec: 54128
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-27-matthew.d.roper@intel.com
Vswing programming for SNPS PHYs is just a single step -- look up the
value that corresponds to the voltage level from a table and program it
into the SNPS_PHY_TX_EQ register.
Bspec: 53920
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-26-matthew.d.roper@intel.com
At the moment we don't have a proper algorithm that can be used to
calculate PHY settings for arbitrary HDMI link rates. The PHY tables
here should support the regular modes of real-world HDMI monitors.
Bspec: 54032
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-25-matthew.d.roper@intel.com
HDMI and DisplayPort sequences states that audio and PSR should be
disabled before planes are disabled.
Not following it did not caused any problems up to Alderlake-P but
for this platform it causes underruns during the PSR2 disable
sequence.
Specification don't mention that DRRS should be disabled before planes
but it looks safer to switch back to the default refresh rate before
following with the rest of the pipe disable sequence.
BSpec: 49191
BSpec: 49190
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726181559.80855-1-jose.souza@intel.com
_DG1_DPCLKA0_CFGCR0 maps between DPLL 0 and 1 with one bit for phy A
and B while _DG1_DPCLKA1_CFGCR0 maps between DPLL 2 and 3 with one
bit for phy C and D.
Reusing _cnl_ddi_get_pll() don't take that into cosideration returing
DPLL 0 and 1 for phy C and D.
That is a regression introduced in the refactor done in
commit 351221ffc5 ("drm/i915: Move DDI clock readout to
encoder->get_config()").
While at it also dropping the macros previously used, not reusing it
to improve readability.
BSpec: 50286
Fixes: 351221ffc5 ("drm/i915: Move DDI clock readout to encoder->get_config()")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210630210522.162674-1-jose.souza@intel.com
Disconnect TypeC PHYs during system suspend and shutdown, even with the
corresponding TypeC sink still plugged to its connector, since leaving
the PHY connected causes havoc at least during system resume in the
presence of an Nvidia card.
Note that this will only make a difference in the TypeC DP alternate
mode, since in Thunderbolt alternate mode the PHY is never owned by the
display engine and there is no notion of PHY ownership in legacy mode
(the display engine being the only possible owner in that mode and the
TypeC subsystem not having anything to do with the port in that case).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3500
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610174223.605904-1-imre.deak@intel.com
Looks this FIXME is still valid as we need a way to tell LSPCON to
stop sending infoframes, so reverting it.
This reverts commit 3f409e4cd5.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210610194527.84997-1-jose.souza@intel.com
intel_dp_set_infoframes() call in intel_ddi_post_disable_dp() will
take care to disable all enabled infoframes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514232247.144542-4-jose.souza@intel.com
An async-put on an encoder specific power domain (for instance the AUX
PW domain) may be pending when removing the encoder. Make sure any such
async-puts are complete while the corresponding encoder is still in place
since at least AUX power wells require this to do a power well->PHY
lookup.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526143729.2563672-1-imre.deak@intel.com
On ADL-P, it's possible to enable the stream splitter on pipe B in
addition to pipe A.
Bspec: 50174
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210526082903.26395-1-jani.nikula@intel.com
On ADL_P besides programming the PLL accordingly the DP/HDMI link rate
should be also programmed to the DDI_BUF_CTL register, do that.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-16-lucas.demarchi@intel.com
Define and use DP voltage swing and pre-emphasis translation tables
for ADL-P.
v2:
- Update according to recent bspec updates; there are now separate
tables for RBR/HBR and HBR2/HBR3. (Anusha)
BSpec: 54956
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-14-lucas.demarchi@intel.com
ADL-P have basically the same TC connection and disconnection
sequences as ICL and TGL, the major difference is the new registers.
So here adding functions without the icl prefix in the name and
making the new functions call the platform specific function to access
the correct register.
v2:
- Retain DDI TC PHY ownership flag during modesetting.
BSpec: 55480
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-6-lucas.demarchi@intel.com
Disable loadgen sharing for DP link rate 1.62 GHz and HDMI 5.94 GHz.
For all other modes, we can enable loadgen sharing feature.
BSpec: 55359
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-13-matthew.d.roper@intel.com
The DDI naming template for display version 12 went A-C, TC1-TC6. With
XE_LPD, that naming scheme for DDI's has now changed to A-E, TC1-TC4.
The XE_LPD design keeps the register offsets and bitfields relating to
the TC outputs in the same location they were previously. The new "D"
and "E" outputs now take the locations that were previously used by TC5
and TC6 outputs, or what we would have considered to be outputs "H" and
"I" under the legacy lettering scheme.
For the most part everything will just work as long as we initialize the
output with the proper 'enum port' value. However we do need to take
care to pick the correct AUX channel when parsing the VBT (e.g., a
reference to 'AUX D' is actually asking us to use the 8th aux channel,
not the fourth). We should also make sure that our encoders and aux
channels are named appropriately so that it's easier to correlate driver
debug messages with the bspec instructions.
v2:
- Update handling of TGL_TRANS_CLK_SEL_PORT. (Jose)
v3:
- Add hpd_pin to handle outputs D and E (Jose)
- Fixed conversion of BIOS port to aux ch for TC ports (Jose)
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210514153711.2359617-2-matthew.d.roper@intel.com
So far if we had a mismatch between the state asked and what was
programmed in hardware for PSR, this mismatch would go unnoticed.
So here adding the PSR to the hardware configuration readout,
EDP_PSR_CTL and EDP_PSR2_CTL can't be directly read because its state
flips due to other factors like frontbuffer modifications and CRC.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210418002126.87882-1-jose.souza@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Just let bxt/glk fall back to intel_hpd_pin_default() instead
of using skl_hpd_pin() or cnl_hpd_pin(). Doesn't really matter
since both functions will end up returning the correct hpd pin
anyway, but I find it a bit less confusing when bxt/glk are
fully separated from the logic for the other platforms.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210412054607.18133-5-ville.syrjala@linux.intel.com
Now that we've eliminated INTEL_GEN(), IS_GEN_RANGE(), etc. from the
display code, we should also kill off our use of the IS_GEN9_* macros
too. We'll do the conversion manually this time instead of using
Coccinelle since the most logical substitution can depend heavily on the
code context, and sometimes we can keep the code simpler if we make
additional adjustments such as swapping the order of if/else arms.
v2:
- Restore a lost negation in intel_pll_is_valid().
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210407203945.1432531-1-matthew.d.roper@intel.com
(cherry picked from commit 70bfb30743)
[Jani: cherry picked to topic branch to reduce conflicts]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
Add intel_bios_encoder_data pointer to encoder, and use it for hdmi and
dp iboost. For starters, we only set the encoder->devdata for DDI
encoders, i.e. we can only use it for data that is used by DDI encoders.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4bc49244ce68e136e5b21db4c4e6554bec9ac0fb.1615998927.git.jani.nikula@intel.com
Stop caching the information in ddi_port_info. We're phasing out
ddi_port_info usage completely, and prefer using the VBT child device
information directly using the provided helpers.
v2:
- Remove supports_typec_usb & supports_tbt from ddi_vbt_port_info (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b04bd183e7554aeb4bc3962af90d63171aa32fc2.1615998927.git.jani.nikula@intel.com
Start using struct intel_bios_encoder_data directly. We'll start
sanitizing the child device data directly as well, instead of the cached
data in ddi_port_info[]. The one downside here is having to store a
non-const pointer back to intel_bios_encoder_data.
Eventually we'll be able to have a direct pointer from encoder to
intel_bios_encoder_data, removing the need to go through the
ddi_port_info[] array altogether. And we'll be able to remove all the
cached data in ddi_port_info[].
v2:
- Remove supports_dp and supports_edp from ddi_port_info too
- Add devdata != NULL check in intel_bios_is_port_edp()
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> # v1
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/061df32a012ff640060920fcd730fb23f8717ee8.1615998927.git.jani.nikula@intel.com
Let's check that we actually found the PLL before doing the
port_clock readout, just in case the hardware was severly
misprogrammed by the previous guy. Not sure the hw would
even survive such misprogramming without hanging but no
real harm in checking anyway.
Cc: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210310194351.6233-1-ville.syrjala@linux.intel.com
Reviewed-by: Karthik B S <karthik.b.s@intel.com>
Now that all the encoder clock stuff is uniformly abstracted
for all hsw+ platforms, let's extend icl_sanitize_encoder_pll_mapping()
to cover all of them.
Not sure there is a particular benefit in doing so, but less special
cases always makes me happy.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-7-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Support reading out the current state of the DDI clock.
Not sure we really want this. Seems a bit excessive just to
restore the debug print to icl_sanitize_encoder_pll_mapping()?
But maybe there's more use for it?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Move the *_get_ddi_pll() stuff into the encodet->get_config() hook.
There it neatly sits next to the matching .{enable,disable}_clock()
functions.
In order to avoid excessive boilerplate I changed the behaviour
such that all platforms now do the readout via
crtc_state->port_dpll[].
ICL+ TC is still a bit special due to TBTPLL not having a functional
.get_freq(). Should probably change that by adopting the LCPLL
approach, but that would require a fairly substantial rework of the
DPLL ID handling. So leave it for later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-5-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
On platforms/outputs without a working frame counter we rely
on the vblank code to cook up the frame counter from the timestamps.
That requires that vblank support is enabled. Thus we need to
move the pipe enable/disable tracepoints to the other side
of the drm_vblank_{on,off}() calls. There shouldn't really be
much happening between these old and new call sites so the
tracepoints should still provide reasonable data.
The alternative would be to give up on having the frame counter
values in the trace which would render the tracepoints more or
less pointless.
v2: Missed one case in intel_ddi_post_disable()
Drop the now useless i915_trace.h includes
Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210304170421.10901-2-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Ville Syrjälä
Jani Nikula
Rodrigo Vivi
Imre Deak
Suraj Kandpal
Mika Kahola
Ankit Nautiyal
José Roberto de Souza
Radhakrishna Sripada
Daniel Vetter
Arun R Murthy
Andrzej Hajda
Vinod Govindapillai
Dave Airlie
Thomas Zimmermann
Lucas De Marchi
Matt Roper
Hans de Goede
Dan Carpenter
Anshuman Gupta