The programming of the DPHY vs. DSI _TIMING registers are
two separate steps in the TGL+ bspec sequence, with some
other stuff in between. Implement the same split.
Windows also seems follow the bspec TGL+ sequence, even
on ICL/JSL.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-5-ville.syrjala@linux.intel.com
Doing the init OTP and display on DSI sequences back to back
doesn't really make any sense (a single sequence would suffice
then). Move the display on sequence to be done just before
backlight on, which is also what Windows does.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-3-ville.syrjala@linux.intel.com
Looks like we're trying to talk to the DSI panel even before turning
it on, on icl+. Bspec doesn't actually specify when these should be
done, but certainly we need to turn the panel on at least before
talking to it. So let's move the power on + reset deassert steps to
be the first thing we do. This is also what Windows does.
v2: s/intel_dsi_msleep/msleep/
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230608203057.23759-2-ville.syrjala@linux.intel.com
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
The intel_dsi_msleep() helper skips sleeping if the MIPI-sequences have
a version of 3 or newer and the panel is in vid-mode.
This is based on the big comment around line 730 which starts with
"Panel enable/disable sequences from the VBT spec.", where
the "v3 video mode seq" column does not have any wait t# entries.
Checking the Windows driver shows that it does always honor
the VBT delays independent of the version of the VBT sequences.
Commit 6fdb335f1c ("drm/i915/dsi: Use unconditional msleep for
the panel_on_delay when there is no reset-deassert MIPI-sequence")
switched to a direct msleep() instead of intel_dsi_msleep()
when there is no MIPI_SEQ_DEASSERT_RESET sequence, to fix
the panel on an Acer Aspire Switch 10 E SW3-016 not turning on.
And now testing on a Nextbook Ares 8A shows that panel_on_delay
must always be honored otherwise the panel will not turn on.
Instead of only always using regular msleep() for panel_on_delay
do as Windows does and always use regular msleep() everywhere
were intel_dsi_msleep() is used and drop the intel_dsi_msleep()
helper.
Changes in v2:
- Replace all intel_dsi_msleep() calls instead of just
the intel_dsi_msleep(panel_on_delay) call
Cc: stable@vger.kernel.org
Fixes: 6fdb335f1c ("drm/i915/dsi: Use unconditional msleep for the panel_on_delay when there is no reset-deassert MIPI-sequence")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230425194441.68086-1-hdegoede@redhat.com
Now that we have laid the groundwork for YUV420 Enablement
we fill up native_420 field in vdsc_cfg and add appropriate
checks wherever required.
---v2
-adding native_422 field as 0 [Vandita]
-filling in second_line_bpg_offset, second_line_offset_adj
and nsl_bpg_offset in vds_cfg when native_420 is true
---v3
-adding display version check to solve igt issue
--v7
-remove is_pipe_dsc check as its always true for D14 [Jani]
--v10
-keep sink capability check [Jani]
-move from !(x == y || w == z) to x !=y && w != z [Jani]
--v11
-avoid native_420 computation if not gen14 [Uma]
--v12
-fix state mismatch issue of compressed_bpp
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230309062855.393087-6-suraj.kandpal@intel.com
On TGL+ the DSS control registers are at different offsets, and there's
one per pipe. Fix the offsets to fix dual link DSI for TGL+.
There would be helpers for this in the DSC code, but just do the quick
fix now for DSI. Long term, we should probably move all the DSS handling
into intel_vdsc.c, so exporting the helpers seems counter-productive.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8232
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301151409.1581574-1-jani.nikula@intel.com
The DSI code has some local hacks to program TRANS_VBLANK on
TGL+ (ICL DSI transcoders didn't have this register). That
will not work when we need to start using the delayed vblank
(for DSB purposes). Too lazy to figure out what the is going
on there, so just sprinkle FIXMEs in the hopes someone else
will spot them eventually.
v2: Only TRANS_{HBLANK,SET_CONTEXT_LATENCY} still no not
exist for DSI transcoders, only TRANS_VBLANK
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-12-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Define the contents of the transcoder timing registers using
REG_GENMASK() & co. For ease of maintenance let's just define
the bitmasks with the full 16bit width (also used by the
current hand rolled stuff) even though not all bits are actually
used. None of the unsued bits have ever contained anything.
Jani spotted that the CRT load detection code did use narrower
bitmasks, so that is now going to change. But that is fine
since any garbage in the high bits would have been caught by
the state checker that always used the full 16bit masks.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rename PIPECONF to TRANSCONF to make it clear what it actually
applies to.
While the usual convention is to pick the earliers name I think
in this case it's more clear to use the later name. Especially
as even the register offset is in the wrong range (0x70000 vs.
0x60000) and thus makes it look like this is per-pipe.
There is one place in gvt that's doing something with TRANSCONF
while iterating with for_each_pipe(). So that might not be doing
the right thing for TRANSCODER_EDP, dunno. Not knowing what it
does I left it as is to avoid breakage.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Name the CPU transcoder timing registers TRANS_FOO rather than
just FOO. This is the modern name, after the pipe/transcoder split
happened. Makes it a bit more obvious whether you pass in a pipe or
a transcoder.
PIPESRC is a bit special as it's a pipe register, even though it
lives in the transcoder registers range (0x60000 instead of 0x70000).
And BCLRPAT I suppose is a transcoder register (since it has something
to do with the timing generator), but it doesn't even exist after gen4
so I left it to use the only name it ever had in bspec.
And while at it let's pass in the correct enum in few more
places why don't we. Although in all those places the distinction
doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230213225258.2127-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We now have some eDP+DSI dual panel systems floating around
where the DSI panel is the secondary LFP and thus needs to
consult "panel type 2" in VBT in order to locate all the
other panel type dependant stuff correctly.
To that end we need to pass in the devdata to
intel_bios_init_panel_late(), otherwise it'll just assume
we want the primary panel type. So let's try to just populate
the vbt.ports[] stuff and encoder->devdata for icl+ DSI
panels as well.
We can't do this on older platforms as there we risk a DSI
port aliasing with a HDMI/DP port, which is a totally legal
thing as the DSI ports live in their own little parallel
universe.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8016
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230207064337.18697-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
It's a bit confusing to have two cached EDIDs in struct intel_connector
with slightly different purposes. Make the distinction a bit clearer by
moving the EDID cached for eDP and LVDS panels at connector init time to
struct intel_panel, and name it fixed_edid. That's what it is, a fixed
EDID for the panels.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/328350ef918638928a8286cdbab3107c8258332d.1674643465.git.jani.nikula@intel.com
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
All the connectors are zero initialized so no need to clear
the *_allowed flags we don't support. Only leave the ones we want
to set. And while at it switch to booleans instead of ints.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Consolidate the scaling_mode property setup into a single
place.
The one slight complicateion here is that GMCH platforms can't
do the CENTER mode except on the LVDS port. But we can deal with
that by just checking the connector type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Currently, pic_height of vdsc_cfg structure is being used to calculate
slice_height, before it is set for DP.
So taking out the lines to set pic_height from the helper
intel_dp_dsc_compute_params() to individual encoders, and setting
pic_height, before it is used to calculate slice_height for DP.
Fixes: 5a6d866f8e ("drm/i915: Get slice height before computing rc params")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902103219.1168781-1-ankit.k.nautiyal@intel.com
Declutter i915_reg.h by splitting backlight registers to a separate
file. Also include the utility pin definitions, even though they are
used for non-backlight things too.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220815094838.3511723-1-jani.nikula@intel.com
Each LFP may have different panel type which is stored in LFP data
data block. Based on the child device index respective panel-type/
panel-type2 field will be used.
v1: Initial rfc verion.
v2: Based on review comments from Jani,
- Used panel-type instead addition panel-index variable.
- DEVICE_HANDLE_* name changed and placed before DEVICE_TYPE_*
macro.
v3:
- passing intel_bios_encoder_data as argument of
intel_bios_init_panel(). Passing NULL to indicate encoder is not
initialized yet for dsi as current focus is to enable dual EDP. [Jani]
v4:
- encoder->devdata used which is initialized before from vbt
structure. [Jani]
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620065138.5126-1-animesh.manna@intel.com
Apparently when the VBT panel_type==0xff we should trawl through
the PNPID table and check for a match against the EDID. If a
match is found the index gives us the panel_type.
Tried to match the Windows behaviour here with first looking
for an exact match, and if one isn't found we fall back to
looking for a match w/o the mfg year/week.
v2: Rebase due to vlv_dsi changes
v3: Adjust to .get_panel_type() vfunc
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5545
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-14-ville.syrjala@linux.intel.com
Move the panel specific VBT parsing to happen during the
output probing stage. Needs to be done because the VBT
parsing will need to look at the EDID to determine
the correct panel_type on some machines.
We split the parsed VBT data (i915->vbt) along the same
boundary. For the moment we just hoist all the panel
specific stuff into connector->panel.vbt since that seems
like the most convenient place for eg. the backlight code.
Note that we simply drop the drrs type check from
intel_drrs_frontbuffer_update() since that operates on the whole
device rather than a specific connector/encoder. But the check
was just a micro optimization so removing it doesn't actually
mattter for correctness.
TODO: Lot's of cleanup to be done in the future. Eg. most of
the DSI stuff could probably be eliminated entirely and just
parsed on demand during DSI init.
v2: Note the intel_drrs_frontbuffer_update() change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
drm/i915 feature pull #2 for v5.19:
Features and functionality:
- Add first set of DG2 PCI IDs for "motherboard down" designs (Matt Roper)
- Add initial RPL-P PCI IDs as ADL-P subplatform (Matt Atwood)
Refactoring and cleanups:
- Power well refactoring and cleanup (Imre)
- GVT-g refactor and mdev API cleanup (Christoph, Jason, Zhi)
- DPLL refactoring and cleanup (Ville)
- VBT panel specific data parsing cleanup (Ville)
- Use drm_mode_init() for on-stack modes (Ville)
Fixes:
- Fix PSR state pipe A/B confusion by clearing more state on disable (José)
- Fix FIFO underruns caused by not taking DRAM channel into account (Vinod)
- Fix FBC flicker on display 11+ by enabling a workaround (José)
- Fix VBT seamless DRRS min refresh rate check (Ville)
- Fix panel type assumption on bogus VBT data (Ville)
- Fix panel data parsing for VBT that misses panel data pointers block (Ville)
- Fix spurious AUX timeout/hotplug handling on LTTPR links (Imre)
Merges:
- Backmerge drm-next (Jani)
- GVT changes (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87bkwbkkdo.fsf@intel.com
DSC is the Display Stream Compression standard for DisplayPort. Move
the DSC code into display/ and split the header into files for protocol
core and DRM helpers. Adapt all users of the code. No functional
changes.
To avoid the proliferation of Kconfig options, DSC is part of DRM's
support for DisplayPort. If necessary, a new option could make DSC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-6-tzimmermann@suse.de
Rather than having the connector init get the fixed mode back from
intel_panel and then feed it straight back into intel_panel_init()
let's just make the fixed mode lookup put the mode directly onto
the panel's fixed_modes list. Avoids the pointless round trip and
opens the door for further enhancements to the fixed mode handling.
v2: Make the debug message correct by using intel_panel_drrs_type() (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rename intel_panel_vbt_fixed_mode() to
intel_panel_vbt_lfp_fixed_mode() to be more descriptive.
We'll have another VBT fixed mode function soon and we
don't want to confuse the two.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Use intel_panel_preferred_fixed_mode() for all the orientation
quirk setup and compute_is_dual_link_lvds()). All of these
happen after intel_panel_init() so the panel fixed_mode list
is already in place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323182935.4701-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We want to eventually get rid of the connector->panel.fixed_mode
pointer so avoid using it during DSI property setup. Since this
all happens during the encoder init we already have the fixed_mode
around, just pass that in.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220311172428.14685-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The VBT DSI video transfer mode field values have been defined in terms
of the VLV MIPI_VIDEO_MODE_FORMAT register. The ICL DSI code maps that
to ICL DSI_TRANS_FUNC_CONF() register. The values are the same, though
the shift is different.
Make a clean break and disassociate the values from each other. Assume
the values can be different, and translate the VBT value to VLV and ICL
register values as needed. Use the existing macros from intel_bios.h.
This will be useful in splitting the DSI register macros to files by DSI
implementation.
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220217224023.3994777-1-jani.nikula@intel.com
Lift the dsc/joiner enable up from the wonky places where it
currently sits (ddi .pre_enable() or icl_ddi_bigjoiner_pre_enable())
into hsw_crtc_enable() where we write the other per-pipe stuff
as well. Makes the transcoder vs. pipe split less confusing.
For DSI this results in slight reordering between the dsc/joiner
enable vs. transcoder timings setup, but I can't really think
why that should cause any issues since the transcoder isn't yet
enabled at that point.
v2: Take care of dsi (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220125063937.7003-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
This reverts commit 991d9557b0 ("drm/i915/tgl/dsi: Gate the ddi clocks
after pll mapping"). The Bspec was updated recently with the pll ungate
sequence similar to that of icl dsi enable sequence. Hence reverting.
Bspec: 49187
Fixes: 991d9557b0 ("drm/i915/tgl/dsi: Gate the ddi clocks after pll mapping")
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109120428.15211-1-vandita.kulkarni@intel.com
Avoid setting LP_DATA_TRANSFER when enable_lpdt is false
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: William Tseng <william.tseng@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109034125.11291-1-william.tseng@intel.com
The PPS SDP is fed into the transcoder whereas the DSC
block is (or at least can be) per pipe. Let's split these
into two distinct operations in an effort to untagle the
bigjoiner mess where we have two pipes feeding a single
transcoder.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-7-ville.syrjala@linux.intel.com
Having two functions for this seems like excess duplication and
parameter juggling. Merge them together.
While at it, drop the extra error message, as wait_for_payload_credits()
already prints an error, and switch from incidental -EPERM (i.e. -1) to
actual error codes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f74f7462a36e76070db6b4c01616d0eb663b9938.1633000838.git.jani.nikula@intel.com
Let's introduce a compute_config() helper for fixed mode panels.
For now all it does is the fixed_mode->adjusted_mode copy.
Note that with sDVO we have to ask the external encoder chip
to spit out our actual display timings for us, so the fixed_mode
to adjusted_mode copy done by intel_panel_compute_config() is
redundant, but we still want to use it to do other checks for us
later. We'll be fine so long as we only call it before
intel_sdvo_get_preferred_input_mode() overwrites adjusted_mode
with the timings from the encoder.
v2: Use intel_panel_compute_config() with sDVO
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210927185207.13620-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Atm during driver loading and system resume TypeC ports are accessed
before their HW/SW state is synced. Move the TypeC port sanitization to
the encoder's sync_state hook to fix this.
v2: Handle the encoder disabled case in gen11_dsi_sync_state() as well
(Jose, Jani)
Fixes: f9e76a6e68 ("drm/i915: Add an encoder hook to sanitize its state during init/resume")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210929132833.2253961-1-imre.deak@intel.com
According to chapter "Sending Commands to the Panel" in bspec #29738
and #49188. If driver try to send DCS long pakcet, we have to program
TX payload register at first. And configure TX header HW register later.
DSC long packet would not be sent properly if we don't follow this
sequence.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-3-shawn.c.lee@intel.com
Driver should wait for free header or payload buffer in FIFO.
It would be good to wait a while for HW to release credit before
give it up to write to HW. Without sending initailize command
sets completely. It would caused MIPI display can't light up properly.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-2-shawn.c.lee@intel.com
Wa_16012360555 SW will have to program the "LP to HS Wakeup Guardband"
field to account for the repeaters on the HS Request/Ready PPI signaling
between the Display engine and the DPHY.
v2: Fix build issue.
v3: Align to new naming (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-2-vandita.kulkarni@intel.com
When pipe A is disabled and MIPI DSI is enabled on pipe B,
the AMT KVMR feature will incorrectly see pipe A as enabled.
Set 0x42080 bit 23=1 before enabling DSI on pipe B and leave
it set while DSI is enabled on pipe B. No impact to setting
it all the time.
Changes since V5:
- Added reviewed-by
- Removed redundant braces and debug message format - Imre
Changes since V4:
- Modified function comment Wa_<number>:icl,jsl,ehl - Lucas
- Modified debug message in sync state - Imre
Changes since V3:
- More meaningful name to workaround - Imre
- Remove boolean check clear flag
- Add WA_verify hook in dsi sync_state
Changes since V2:
- Used REG_BIT, ignored pipe A and used sw state check - Jani
- Made function wrapper - Jani
Changes since V1:
- ./dim checkpatch errors addressed
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210615105613.851491-1-tejaskumarx.surendrakumar.upadhyay@intel.com
Today when the DSI controller is paired with the Combo-PHY it
uses the high-speed (HS) Word clock for its low power (LP)
transmit PPI communication to the DPHY. The interface signaling
only changes state at an Escape clock frequency (i.e. its
effectively running on a virtual Tx Escape clock that is controlled
by counters w/in the controller), but all the interface flops are
running off the HS clock.
This has the following drawbacks:
* It is a deviation from the PPI spec which assumes signaling is
running on a physical Escape clock
* The PV timings are over constrained (HS timed to 312.5MHz vs.
an Escape clock of 20MHz max)
This feature is proposing to change the LP Tx communication between
the controller and the DPHY from a virtual Tx Escape clock to a physical
clock.
To do this we need to program two "M" divisors. One for the usual
DSI_ESC_CLK_DIV and DPHY_ESC_CLK_DIV register and one for MIPIO_DWORD8.
For DSI_ESC_CLK_DIV and DPHY_ESC_CLK_DIV registers the "M" is calculated
as following
Nt = ceil(f_link/160) (theoretical word clock)
Nact = max[3, Nt + (Nt + 1)%2] (actual word clock)
M = Nact * 8
For MIPIO_DWORD8 register, the divisor "M" is calculated as following
M = (Nact - 1)/2
BSpec: 55171
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210519000625.3184321-11-lucas.demarchi@intel.com
Hoist the intel_de.h include from intel_display_types.h one
level up. I need this in order to untangle the include order
so that I can add tracepoints into intel_de.h.
This little cocci script did most of the work for me:
@find@
@@
(
intel_de_read(...)
|
intel_de_read_fw(...)
|
intel_de_write(...)
|
intel_de_write_fw(...)
)
@has_include@
@@
(
#include "intel_de.h"
|
#include "display/intel_de.h"
)
@depends on find && !has_include@
@@
+ #include "intel_de.h"
#include "intel_display_types.h"
@depends on find && !has_include@
@@
+ #include "display/intel_de.h"
#include "display/intel_display_types.h"
Cc: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430143945.6776-1-ville.syrjala@linux.intel.com
While converting the rest of the driver to use GRAPHICS_VER() and
MEDIA_VER(), following what was done for display, some discussions went
back on what we did for display:
1) Why is the == comparison special that deserves a separate
macro instead of just getting the version and comparing directly
like is done for >, >=, <=?
2) IS_DISPLAY_RANGE() is weird in that it omits the "_VER" for
brevity. If we remove the current users of IS_DISPLAY_VER(), we
could actually repurpose it for a range check
With (1) there could be an advantage if we used gen_mask since multiple
conditionals be combined by the compiler in a single and instruction and
check the result. However a) INTEL_GEN() doesn't use the mask since it
would make the code bigger everywhere else and b) in the cases it made
sense, it also made sense to convert to the _RANGE() variant.
So here we repurpose IS_DISPLAY_VER() to work with a [ from, to ] range
like was the IS_DISPLAY_RANGE() and convert the current IS_DISPLAY_VER()
users to use == and != operators. Aside from the definition changes,
this was done by the following semantic patch:
@@ expression dev_priv, E1; @@
- !IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) != E1
@@ expression dev_priv, E1; @@
- IS_DISPLAY_VER(dev_priv, E1)
+ DISPLAY_VER(dev_priv) == E1
@@ expression dev_priv, from, until; @@
- IS_DISPLAY_RANGE(dev_priv, from, until)
+ IS_DISPLAY_VER(dev_priv, from, until)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Jani: Minor conflict resolve while applying.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210413051002.92589-4-lucas.demarchi@intel.com
Use Coccinelle to convert most of the usage of INTEL_GEN() and IS_GEN()
in the display code to use DISPLAY_VER() comparisons instead. The
following semantic patch was used:
@@ expression dev_priv, E; @@
- INTEL_GEN(dev_priv) == E
+ IS_DISPLAY_VER(dev_priv, E)
@@ expression dev_priv; @@
- INTEL_GEN(dev_priv)
+ DISPLAY_VER(dev_priv)
@@ expression dev_priv; expression E; @@
- IS_GEN(dev_priv, E)
+ IS_DISPLAY_VER(dev_priv, E)
@@
expression dev_priv;
expression from, until;
@@
- IS_GEN_RANGE(dev_priv, from, until)
+ IS_DISPLAY_RANGE(dev_priv, from, until)
There are still some display-related uses of INTEL_GEN() in intel_pm.c
(watermark code) and i915_irq.c. Those will be updated separately.
v2:
- Use new IS_DISPLAY_RANGE and IS_DISPLAY_VER helpers. (Jani)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210320044245.3920043-4-matthew.d.roper@intel.com
Support reading out the current state of the DDI clock.
Not sure we really want this. Seems a bit excessive just to
restore the debug print to icl_sanitize_encoder_pll_mapping()?
But maybe there's more use for it?
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-6-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Move the *_get_ddi_pll() stuff into the encodet->get_config() hook.
There it neatly sits next to the matching .{enable,disable}_clock()
functions.
In order to avoid excessive boilerplate I changed the behaviour
such that all platforms now do the readout via
crtc_state->port_dpll[].
ICL+ TC is still a bit special due to TBTPLL not having a functional
.get_freq(). Should probably change that by adopting the LCPLL
approach, but that would require a fairly substantial rework of the
DPLL ID handling. So leave it for later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224144214.24803-5-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Instead of every new platform having yet another masive
copy of the whole PLL sanitation code, let's just reuse the
.disable_clock() hook for this purpose. We do need to plug
this into the ICL+ DSI code for that, but fortunately it
already has a suitable function we can use.
We do lose the debug message though on account of not bothering
to check if the clock is actually enabled or not before turning
it off. We could introduce yet another vfunc to query the current
state, but not sure it's worth the hassle?
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210205214634.19341-14-ville.syrjala@linux.intel.com
This moves the code from various places and consolidates it
into one new file.
v2:
- rename skl_program_plane -> skl_program_plane_scaler (Ville)
- also move skl_pfit_enable, and consequently make some skl_scaler_*
functions static to skl_scaler.c (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2fa703ffc7b96a41c392fd5ebbd2e6e4ffb6fb05.1612536383.git.jani.nikula@intel.com
Rework the plane init calls to do the gen test one level higher.
Rework some of the plane helpers so they can live in new file,
there is still some scope to clean up the plane/fb interactions
later.
v2: drop atomic code back, rename file to Ville suggestions,
add header file.
v3: move scaler bits back
v4: drop wrong new includes (Ville)
v5: integrate the ccs gen12 changes
v6: fix unrelated code movement (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Jani: fixed up sparse warnings.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/4e88a5c6b9ab3b93cc2b6c7d78c26ae86f6abbd0.1612536383.git.jani.nikula@intel.com
For an enabled DSC during HW readout the corresponding power reference
is taken along the CRTC power domain references in
get_crtc_power_domains(). Remove the incorrect get ref from the DSI
encoder hook.
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209153952.3397959-1-imre.deak@intel.com
Move the initialization of the rc_model_size from the common code into
encoder code, allowing different encoders to specify the size according
to their needs. Keep using the hard coded value in the encoders for now
to make this a non-functional change.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6843c4f6958619f7389180aa92fded7b9fdbb4ba.1607429866.git.jani.nikula@intel.com
Skip iterating over bigjoiner slaves, only the master has the state we
care about.
Add the width of the bigjoiner slave to the reconstructed fb.
Hide the bigjoiner slave to userspace, and double the mode on bigjoiner
master.
And last, disable bigjoiner slave from primary if reconstruction fails.
v3:
* Fix the ddi_get_config slave error (Ankit Nautiyal)
v2:
* Unsupported bigjoiner config for initial fb (Ville)
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[vsyrjala:
* Don't do any hw->uapi state copy for bigjoiner slave
* We still have hw.mode so no need to pass it in
* Appease checkpatch]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-7-manasi.d.navare@intel.com
Make vdsc work when no output is enabled. The big joiner needs VDSC
on the slave, so enable it and set the appropriate bits.
So remove encoder usage from dsc functions.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117194718.11462-5-manasi.d.navare@intel.com
Currently the DPLL .get_freq() uses pll->state.hw_state which
is not the thing we actually read out (except during driver
load/resume). Outside of that pll->state.hw_state is just the
thing we committed last time around. During state check we
just read the thing into crtc_state->dpll_hw_state, so that
is what we should use for calculating the DPLL output frequency.
I think we used to do this so that the results of the readout
were actually used, but somehow it got changed when the
.get_freq() refactoring happened.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109231239.17002-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Recently we came across requirement to identify EHL and JSL
platform to program them differently. Thus Split the basic
platform definition, macros, and PCI IDs to differentiate
between EHL and JSL platforms. Also, IS_ELKHARTLAKE is replaced
with IS_JSL_EHL everywhere.
Changes since V1 :
- Rebased to avoid merge conflicts
- Added missed check for jasperlake in intel_uc_fw.c
Cc : Matt Roper <matthew.d.roper@intel.com>
Cc : Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201013192948.63470-1-tejaskumarx.surendrakumar.upadhyay@intel.com
Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.
v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com
In TE Gate mode or TE NO_GATE mode on every flip we need to set the
frame update request bit. After this bit is set transcoder hardware will
automatically send the frame data to the panel in case of TE NO_GATE
mode, where it sends after it receives the TE event in case of TE_GATE
mode. Once the frame data is sent to the panel, we see the frame counter
updating.
v2: Use intel_de_read/write
v3: remove the usage of private_flags
v4: Use icl_dsi in func names if non static,
fix code formatting issues. (Jani)
v5: Send frame update request at the beginning of
pipe_update_end, use crtc_state mode_flags (Ville)
v6: Add platform and dsi checks (Ville)
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200928110834.15077-1-vandita.kulkarni@intel.com
We need details about enabling TE on which port before we enable TE
through vblank enable path. This is based on the configuration that we
receive from the VBT wrt ports, dual_link.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200924124209.17916-2-vandita.kulkarni@intel.com
Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.
v2: Put the check into the right place for CRT
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
If an error is encountered during the DSI initialization setup, the
drm connector object also needs to be cleaned up along with the encoder.
The error can happen due to a missing mode in the VBT or for other
reasons.
v2: Rephrase the commit message to make it more clear.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200522202630.7604-1-vivek.kasireddy@intel.com
Replace the use of mode->private_flags with a truly private bitmaks
in our own crtc state. We also need a copy in the crtc itself so the
vblank code can get at it. We already have scanline_offset in there
for a similar reason, as well as the vblank->hwmode which is assigned
via drm_calc_timestamping_constants(). Fortunately we now have a
nice place for doing the crtc_state->crtc copy in
intel_crtc_update_active_timings() which gets called both for
modesets and init/resume readout.
The one slightly iffy spot is the INHERITED flag which we want to
preserve until userspace/fb_helper does the first proper commit after
actually calling .detecti() on the connectors. Otherwise we don't have
the full sink capabilities (audio,infoframes,etc.) when .compute_config()
gets called and thus we will fail to enable those features when the
first userspace commit happens. The only internal commit we do prior to
that should be from intel_initial_commit() and there we can simply
preserve the INHERITED flag from the readout.
v2: Deal with INHERITED in sanitize_watermarks() as well
CC: Sam Ravnborg <sam@ravnborg.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200429103904.11727-1-ville.syrjala@linux.intel.com
Pass the entire connector state to intel_{gmch,pch}_panel_fitting().
For now we just need to get at .scaling_mode but in the future we'll
want access to the margin properties as well.
v2: Deal with intel_dp_ycbcr420_config()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200422161917.17389-5-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Remove a number of inlines from .c files, and let the compiler decide
what's best. There's more to do, but need to start somewhere, and need
to start setting the example.
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200420140438.14672-2-jani.nikula@intel.com
We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.
The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.
Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
On dsi cmd mode we do not receive vblanks instead
we would get TE and these flags indicate TE is expected on
which port.
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-6-vandita.kulkarni@intel.com
If the GOP has programmed periodic command mode,
we need to disable that which would need a
deconfigure and configure sequence.
v2: Fix sparse error, pass only intel_dsi (Jani)
v3: Use intel_de_read
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-5-vandita.kulkarni@intel.com
Transcoder timing calculation differ for command mode.
v2: Use is_vid_mode, and use same I915_WRITE (Jani)
v3: Adjust the calculations to reflect dsc compression ratio
v4: Rearrange the vertical and horizontal timing calc, optimize
local variables usage. (Jani)
v5: Fix the values used for calculation, use afe_clk for
byte clock calculation, use intel_de_write/read (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-3-vandita.kulkarni@intel.com
Configure the transcoder to operate in TE GATE command mode
and take TE events from GPIO.
Also disable the periodic command mode, that GOP would have
programmed.
v2: Disable util pin (Jani)
v3: Use intel_de_write (Jani)
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312053841.2794-2-vandita.kulkarni@intel.com
Move all the DPLL params->DPLL frequency conversion functions to
intel_dpll_mgr.c where the corresponding inverse conversions are.
The GEN11+ TBT PLL outputs multiple frequencies and for selecting the
one in use we need to check the DDI CLK mux. As part of the DDI clock
logic this selection is kept in intel_ddi.c.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226203455.23032-7-imre.deak@intel.com
Ville Syrjälä
Ankit Nautiyal
Hans de Goede
Suraj Kandpal
Jani Nikula
Andrzej Hajda
Dave Airlie
Animesh Manna
Thomas Zimmermann
Imre Deak
Matt Roper
Vandita Kulkarni
William Tseng
Lee Shawn C
Tejas Upadhyay
Mika Kahola
Lucas De Marchi
Manasi Navare
Gustavo A. R. Silva
Vivek Kasireddy
Pankaj Bharadiya