There's an issue in that when we disconnect from an AP
due to the AP switching to an unsupported channel, we
might not tell the driver about this before we try to
send the deauth. If the underlying implementation has
detected the quiet CSA, this may cause issues if this
is the only active link. Avoid this by transmitting
(and flushing) the deauth only when there's an active
link available that's not affected by quiet CSA.
Since this introduces link->u.mgd.csa_blocked_tx and we
no longer check sdata->csa_blocked_tx for the TX itself
also rename the latter to csa_blocked_queues.
Fixes: 6f0107d195 ("wifi: mac80211: introduce a feature flag for quiet in CSA")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415112355.1d91db5e95aa.Iad3a5df3367f305dff48cd61776abfd6cf0fd4ab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The AP removal timer field need not be aligned, so the
code shouldn't access it directly, but use unaligned
loads. Use get_unaligned_le16(), which even is shorter
than the current code since it doesn't need a cast.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.356788ba0045.I2b3cdb3644e205d5bb10322c345c0499171cf5d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP removal timer is long, we don't really want to
remove the link immediately. However, we really should do
it _before_ the AP removes it (which happens at or after
count reaches 0), so subtract 1 from the countdown when
scheduling the timer. This causes the link removal work
to run just after the beacon with value 1 is received. If
the counter is already zero, do it immediately.
This fixes an issue where we do the removal too late and
receive a beacon from the AP that's no longer associated
with the MLD, but thus removed EHT and ML elements, and
then we disconnect instead from the whole MLD, since one
of the associated APs changed mode from EHT to HE.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.03ac4a09fa74.Ifb8c8d38e3402721a81ce5981568f47b5c5889cb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP mode ends up being determined less than the client mode,
there may be different reasons for this, e.g. AP misconfiguration.
If this happens in a way that causes e.g. EHT to be rejected, the
elements need to be re-parsed since we'll connect as HE, but not
reparsing means that we'll still think it's OK to use multi-link,
so we can connect in a non-sensical configuration of advertising
only HE on a secondary link. This normally won't happen for the
assoc link because that reuses the mode from authentication, and
if that's not EHT, multi-link association is rejected.
Fix this inconsistency by parsing the elements again if the mode
was different from the first parsing attempt. Print the message a
bit later to avoid printing "determined AP ... to be HE" twice in
cases where ieee80211_determine_ap_chan() returned a lesser mode,
rather than the regulatory downgrades below changing it.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.d1f25d92cfe7.Ia21eff6cdcae2f5aca13cf8e742a986af5e70f89@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing re-parsing in ieee80211_determine_chan_mode(),
the conn->mode is changed, and the whole point of doing
the parsing again was to parse as the downgraded mode.
However, that didn't actually work, because the setting
was copied before and never changed again. Fix that.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240418105220.5e0d1fcb5622.Ib0673e0bc90033fd6d387b6a5f107c040eb907cf@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Logic inside ieee80211_rx_mgmt_beacon accesses the
mgmt->u.beacon.timestamp field without first checking whether the beacon
received is non-S1G format.
Fix the problem by checking the beacon is non-S1G format to avoid access
of the mgmt->u.beacon.timestamp field.
Signed-off-by: Richard Kinder <richard.kinder@gmail.com>
Link: https://msgid.link/20240328005725.85355-1-richard.kinder@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi as we didn't consider it
as major enough to justify merging wireless tree to wireless-next. But
Stephen has an example merge resolution which should help with fixing
the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmYNIqIRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt8jAf9H+o91boD34/qVdI5LWEcFhVKEkHpNtwm
Y1sTKNBEtN1Gs2zcljjO6PqN9N4v2+lA42KSpzP5M42FfpI2aATI2v8jYsKTXOl2
YVwF+8pDiAsi0YtQTxIthygjzTpsePCfj8z0xJaKGm195T+fMm9UebYETrfxxOp/
z5StsJIPI0twgSLKKUWvLpX4ESt0l0HLJY1ok99sk4Cj36EKn6b9LbBinDKr6GcQ
mGNtPyq0j4l0kS5qae9BbXZUohO54o8wiFnApdwGfA7S/kLY7eUtwZy7T050b62P
zbNafwZbIjrH7dNcGfe6Fdr7PjQYFeI5Nh7dXxqM2LJOQsYXU/tcWQ==
=WrPE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.10
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi, Stephen has an example
merge resolution which should help with fixing the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
* tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (122 commits)
wifi: mt76: mt7915: workaround dubious x | !y warning
wifi: mwl8k: Avoid -Wflex-array-member-not-at-end warnings
wifi: ti: Avoid a hundred -Wflex-array-member-not-at-end warnings
wifi: iwlwifi: mvm: fix check in iwl_mvm_sta_fw_id_mask
net: rfkill: gpio: Convert to platform remove callback returning void
wifi: mac80211: use kvcalloc() for codel vars
wifi: iwlwifi: reconfigure TLC during HW restart
wifi: iwlwifi: mvm: don't change BA sessions during restart
wifi: iwlwifi: mvm: select STA mask only for active links
wifi: iwlwifi: mvm: set wider BW OFDMA ignore correctly
wifi: iwlwifi: Add support for LARI_CONFIG_CHANGE_CMD cmd v9
wifi: iwlwifi: mvm: Declare HE/EHT capabilities support for P2P interfaces
wifi: iwlwifi: mvm: Remove outdated comment
wifi: iwlwifi: add support for BZ_W
wifi: iwlwifi: Print a specific device name.
wifi: iwlwifi: remove wrong CRF_IDs
wifi: iwlwifi: remove devices that never came out
wifi: iwlwifi: mvm: mark EMLSR disabled in cleanup iterator
wifi: iwlwifi: mvm: fix active link counting during recovery
wifi: iwlwifi: mvm: assign link STA ID lookups during restart
...
====================
Link: https://lore.kernel.org/r/20240403093625.CF515C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In order to activate a link that is currently inactive due to
a negotiated TTLM request, need to first tear down the negotiated
TTLM request.
Add support for sending TTLM teardown request and update the links
state accordingly.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.d480cbf46fcf.Idedad472469d2c27dd2a088cf80a13a1e1cf9b78@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is no reason to check the request flags for each of the links, so
pull that out of the loop. Also, within the loop we can set the per-link
error everywhere.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.695faa9be279.I71b11a8d66a9cae4c27e242a47d1d92922609b03@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may not be capable of handling puncturing in 5 GHz
only (vs. the current flag that just removes puncturing support
completely). Add a flag to support such devices: check and then
downgrade the channel width if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.49759510da7d.I12c5a61f0be512e0c4e574c2f794ef4b37ecaf6b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update power_type in bss_conf based on Indoor AFC and LPI power types
received in HE 6 GHz operation element on assoc success.
Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.89c25dae34ff.Ifd8b2983f400623ac03dc032fc9a20025c9ca365@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix ieee80211_ttlm_set_links() to not set all active links,
but instead let the driver know that valid links status changed
and select the active links properly.
Fixes: 8f500fbc6c ("wifi: mac80211: process and save negotiated TID to Link mapping request")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.acddbbf39584.Ide858f95248fcb3e483c97fcaa14b0cd4e964b10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If prep_channel fails in prep_connection, the code releases
the deflink's chanctx, which is wrong since we may be using
a different link. It's already wrong to even do that always
though, since we might still have the station. Remove it
only if prep_channel succeeded and later updates fail.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240318184907.2780c1f08c3d.I033c9b15483933088f32a2c0789612a33dd33d82@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a link does CSA, or if it changes SMPS mode, we need to
drop the TDLS peers, but we really should drop them only on
the affected link. Fix that.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095719.00d1d793f5b8.Ia9971316c6b3922dd371d64ac2198f91ed5ad9d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unify all the CSA handling, including handling of a beacon
after the CSA, into ieee80211_sta_process_chanswitch().
The CRC of the beacon will change due to changes in the
CSA/ECSA elements, so there's really no need to have the
'beacon after CSA' handling before the CRC processing or
to change the beacon_crc_valid value here.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.e269c0e02905.I9dc68ff1e84d51349822bc7d3b33b578fcf8e360@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing CSA in multi-link, there really isn't a need to
stop transmissions entirely. Add a feature flag for drivers
to indicate they can handle quiet in CSA (be it by parsing
themselves, or by implementing drv_pre_channel_switch()),
to make that possible.
Also clean up the csa_block_tx handling: it clearly cannot
handle multi-link due to the way queues are stopped, move
it to the sdata. Drivers should be doing it themselves for
working properly during CSA in MLO anyway. Also rename it
to indicate that it reflects TX was blocked at mac80211.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.258439191541.I2469d206e2bf5cb244cfde2b4bbc2ae6d1cd3dd9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link conf to the abort_channel_switch driver
method so the driver can handle things correctly.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095718.27f621106ddd.Iadd3d69b722ffe5934779a32a0e4e596a4e33ed4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For CSA to work correctly in multi-link scenarios, pass
the link_id to the relevant callbacks.
While at it, unify/deduplicate the tracing for them.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://msgid.link/20240228095718.b7726635c054.I0be5d00af4acb48cfbd23a9dbf067f9aeb66469d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using the scratch buffer (without advancing it) here in the
mlme.c code seems somewhat wrong, defragment the reconfig
multi-link element already when parsing. This might be a bit
more work in certain cases, but makes the whole thing more
regular.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094902.92936a3ce216.I4b736ce4fdc199fa1d6b00d00032f448c873a8b4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We shouldn't assign elems->ml_basic{,len} before defragmentation,
and we don't need elems->ml_reconf{,len} at all since we don't do
defragmentation. Clean that up a bit. This does require always
defragmention even when it may not be needed, but that's easier
to reason about.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094902.e0115da4d2a6.I89a80f7387eabef8df3955485d4a583ed024c5b1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the association request, we make some parameters depend on the
AP's HT/VHT information. This was broken by my code because it no
longer filled that information, making it all zero.
For HT that meant we wouldn't reduce our capabilities to 20 MHz if
needed, and for VHT we lost beamforming capabilities.
Fix this. It seems like it may even have been broken for all but
the assoc link before.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094207.7dc812c2060a.Ibd591f9c214b4e166cf7171db3cf63bda8e3c9fd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a link doesn't have VHT capability, before the rework
we'd have set IEEE80211_CONN_DISABLE_VHT, but now with the
linear progression of 'mode', we no longer have that. Add
an explicit check for VHT being supported, so we don't add
a zeroed VHT capabilities element where it shouldn't be.
Fixes: 310c8387c6 ("wifi: mac80211: clean up connection process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094207.bfe4283bcde7.Ib70a558bc6bdbcec3d9e663079229dfcc2493682@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the prototype of ieee80211_mle_get_bss_param_ch_cnt()
to also take a u8 * like the other functions, and make it
return -1 when the field isn't found, so that mac80211 can
check that instead of explicitly open-coding the check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240216135047.583309181bc3.Ia61cb0b4fc034d5ac8fcfaf6f6fb2e115fadafe7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whenever sta_flush() function is invoked, all STAs present in that
interface are flushed. In case of MLO, it is desirable to only flush such
STAs that are at least using a given link id as one of their links.
Add support for this by making change in the __sta_info_flush API argument
to accept a link ID. And then, only if the STA is using the given link as
one of its links, it would be flushed.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240205162952.1697646-3-quic_adisi@quicinc.com
[reword commit message, in particular this isn't about "active" links]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If intending to associate with a lower bandwidth, remove capabilities
related to 320 MHz from the EHT capabilities element. Also change the
EHT MCS-NSS set accordingly: if just reducing 320->160 or similar the
format doesn't change, just cut off the last bytes. If changing from
higher bandwidth to 20 MHz only EHT STA, adjust the format.
Note that this also requires adjusting the caller in mlme.c since the
data written can now be shorter than it determined. We need to clean
all that up. Since the other callers pass NULL for the conn limit, we
don't need to change things there.
Link: https://msgid.link/20240129202041.b5f6df108c77.I0d8ea04079c61cb3744cc88625eeaf0d4776dc2b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Aloka originally suggested that puncturing should be part of
the chandef, so that it's treated correctly. At the time, I
disagreed and it ended up not part of the chandef, but I've
now realized that this was wrong. Even for clients, the RX,
and perhaps more importantly, CCA configuration needs to take
puncturing into account.
Move puncturing into the chandef, and adjust all the code
accordingly. Also add a few tests for puncturing in chandef
compatibility checking.
Link: https://lore.kernel.org/linux-wireless/20220214223051.3610-1-quic_alokad@quicinc.com/
Suggested-by: Aloka Dixit <quic_alokad@quicinc.com>
Link: https://msgid.link/20240129194108.307183a5d2e5.I4d7fe2f126b2366c1312010e2900dfb2abffa0f6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the earlier restructuring we now mostly ignore
the channel configuration in the association response,
apart from the HT/VHT checks we had.
Don't do that, but parse it and update, also dropping the
association if the AP changed its mode in the response.
Link: https://msgid.link/20240129194108.b3efa5eae60c.I1b70c9fd56781b22cdfdca55d34d69f7d0733e31@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
EHT requires that stations are able to participate in
wider bandwidth OFDMA, i.e. parse downlink OFDMA and
uplink OFDMA triggers when they're not capable of (or
not connected at) the (wider) bandwidth that the AP
is using. This requires hardware configuration, since
the entity responsible for parsing (possibly hardware)
needs to know the AP bandwidth.
To support this, change the channel request to have
the AP's bandwidth for clients, and track that in the
channel context in mac80211. This means that the same
chandef might need to be split up into two different
contexts, if the APs are different. Interfaces other
than client are not participating in OFDMA the same
way, so they don't request any AP setting.
Note that this doesn't introduce any API to split a
channel context, so that there are cases where this
might lead to a disconnect, e.g. if there are two
client interfaces using the same channel context, e.g.
both 160 MHz connected to different 320 MHz APs, and
one of the APs switches to 160 MHz.
Note also there are possible cases where this can be
optimised, e.g. when using the upper or lower 160 Mhz,
but I haven't been able to really fully understand the
spec and/or hardware limitations.
If, for some reason, there are no hardware limits on
this because the OFDMA (downlink/trigger) parsing is
done in firmware and can take the transmitter into
account, then drivers can set the new flag
IEEE80211_VIF_IGNORE_OFDMA_WIDER_BW on interfaces to
not have them request any AP bandwidth in the channel
context and ignore this issue entirely. The bss_conf
still contains the AP configuration (if any, i.e. EHT)
in the chanreq.
Link: https://msgid.link/20240129194108.d3d5b35dd783.I939d04674f4ff06f39934b1591c8d36a30ce74c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the code we currently check for support 80+80, 160
and 320 channel widths, but really the way this should
be (and is otherwise) handled is that we compute the
highest channel bandwidth given there, and then cut it
down to what we support. This is also needed for wider
bandwidth OFDMA support.
Change the code to remove this limitation and always
parse the highest possible channel width.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129194108.d06f85082e29.I47e68ed3d97b0a2f4ee61e5d8abfcefc8a5b9c08@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rewrite the station-side connection handling. The connection
flags (IEEE80211_DISABLE_*) are rather confusing, and they're
not always maintained well. Additionally, for wider-bandwidth
OFDMA support we need to know the precise bandwidth of the AP,
which is currently somewhat difficult.
Rewrite this to have a 'mode' (S1G/legacy/HT/...) and a limit
on the bandwidth. This is not entirely clean because some of
those modes aren't completely sequenced (as this assumes in
some places), e.g. VHT doesn't exist on 2.4 GHz, but HE does.
However, it still simplifies things and gives us a good idea
what we're operating as, so we can parse elements accordingly
etc.
This leaves a FIXME for puncturing, this is addressed in a
later patch.
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129194108.9451722c0110.I3e61f4cfe9da89008e1854160093c76a1e69dc2a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mentioned in the previous commit, we pretty quickly found
that some APs have ECSA elements stuck in their probe response,
so using that to not attempt to connect while CSA is happening
we never connect to such an AP.
Improve this situation by checking more carefully and ignoring
the ECSA if cfg80211 has previously detected the ECSA element
being stuck in the probe response.
Additionally, allow connecting to an AP that's switching to a
channel it's already using, unless it's using quiet mode. In
this case, we may just have to adjust bandwidth later. If it's
actually switching channels, it's better not to try to connect
in the middle of that.
Reported-by: coldolt <andypalmadi@gmail.com>
Closes: https://lore.kernel.org/linux-wireless/CAJvGw+DQhBk_mHXeu6RTOds5iramMW2FbMB01VbKRA4YbHHDTA@mail.gmail.com/
Fixes: c09c4f3199 ("wifi: mac80211: don't connect to an AP while it's in a CSA process")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240129131413.cc2d0a26226e.I682c016af76e35b6c47007db50e8554c5a426910@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This does not change anything effectively, but it is closer to what the
code is trying to achieve here. i.e. select the link data if it is an
MLD and fall back to using the deflink otherwise.
Fixes: 0f99f08783 ("wifi: mac80211: Print local link address during authentication")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.4c4b1c40eb3c.I2771621dee328c618536596b7e56232df42a79c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing 6 GHz operation, don't set the bss_conf
values. We only commit to that later in association,
so move the code there. Also clear it later.
While at it, handle IEEE80211_6GHZ_CTRL_REG_VLP_AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c2da4bc515e8.I219ca40e15c0fbaff0e7c3e83ca4b92ecbc1f8ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For verifying the required HE capabilities are supported
locally, we access the HE capability element of the AP.
Simplify that access, we've already parsed and validated
it when parsing elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.2ef62b43caeb.I8baa604dd3f3399e08b86c99395a2c6a1185d35d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already parse all the BSS elements into elems, there's
really no need to separately find EHT/ML again. Remove the
extra code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.c4a55da9f778.I112b1ef00904c4183ac7644800f8daa8a4449875@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only user of this function passes a lot of pointers
directly from the parsed elements, so it's simpler to
just pass the entire elements parsing struct. This also
shows that the ht_cap is actually unused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.f0653cd5e7dd.I8bd5ee848074029a9f0495c95e4339546ad8fe15@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The association response is more likely to be correct
than a random scan result, which really also should be
correct, but we generally prefer to take data from the
association response, so do that here as well.
Also reset the data so it doesn't hang around from an
old connection to a non-MLO connection, drivers would
hopefully not look at it, but less surprise this way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.1d10f1d1dbab.I545e955675e2269a52496a22ae7822d95b40235e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If software crypto is used, simply add support for SPP A-MSDUs
(and use it whenever enabled as required by the cfg80211 API).
If hardware crypto is used, leave it up to the driver to set
the NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT flag and then check
sta->spp_amsdu or the IEEE80211_KEY_FLAG_SPP_AMSDU key flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.b8ada4514e2b.I1ac25d5f158165b5a88062a5a5e4c4fbeecf9a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update neg_ttlm and active_links according to the new mapping,
and send a negotiated TID-to-link map request with the new mapping.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.eeb385d771df.I2a5441c14421de884dbd93d1624ce7bb2c944833@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An MLD may send TID-to-Link mapping request frame to negotiate
TID to link mapping with a peer MLD.
Support handling negotiated TID-to-Link mapping request frame
by parsing the frame, asking the driver whether it supports the
received mapping or not, and sending a TID-to-Link mapping response
to the AP MLD.
Theoretically, links that became inactive due to the received TID-to-Link
mapping request, can be selected to be activated but this would require
tearing down the negotiated TID-to-Link mapping, which is still not
supported.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.0bc1a24fcc9d.Ie72e47dc6f8c77d4a2f0947b775ef6367fe0edac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- first kunit tests for both cfg80211 and mac80211
- a few multi-link fixes
- DSCP mapping update
- RCU fix
-----BEGIN PGP SIGNATURE-----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=dHxp
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Just a couple of more things over the holidays:
- first kunit tests for both cfg80211 and mac80211
- a few multi-link fixes
- DSCP mapping update
- RCU fix
* tag 'wireless-next-2024-01-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next:
wifi: mac80211: remove redundant ML element check
wifi: cfg80211: parse all ML elements in an ML probe response
wifi: cfg80211: correct comment about MLD ID
wifi: cfg80211: Update the default DSCP-to-UP mapping
wifi: cfg80211: tests: add some scanning related tests
wifi: mac80211: kunit: extend MFP tests
wifi: mac80211: kunit: generalize public action test
wifi: mac80211: add kunit tests for public action handling
kunit: add a convenience allocation wrapper for SKBs
kunit: add parameter generation macro using description from array
wifi: mac80211: fix spelling typo in comment
wifi: cfg80211: fix RCU dereference in __cfg80211_bss_update
====================
Link: https://lore.kernel.org/r/20240103144423.52269-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If "ml_basic" is assigned, we already know that the type
of ML element is basic, so we don't need to check again,
that check can never happen. Simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.bb9b636e66f6.I7fc0897022142d46f39ac0b912a4f7b0f1b6ea26@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The third "new features" pull request for v6.8. This is a smaller one
to clear up our tree before the break and nothing really noteworthy
this time.
Major changes:
stack
* cfg80211: introduce cfg80211_ssid_eq() for SSID matching
* cfg80211: support P2P operation on DFS channels
* mac80211: allow 64-bit radiotap timestamps
iwlwifi
* AX210: allow concurrent P2P operation on DFS channels
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWFbnIRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZs5hQf/aCvvTjqeRoMkmO+ZPFMSO+YquZNCJi1M
TP8Fce2ALKj7woPad8vdJNNStMa9k4bu2NvShMXhoYM3xOA/4o0P9yeb5OfyYkTk
Y6JF+SoBGzABtB3m/a3i5J19F+oC+6yKN6/OY8byfK4jqZdrAprc3qXwodC5zb9n
blC16KKlldjoj5AWe/b6Vn/LI9P7mVhZIaWxI9IaktK0eIgfsfcgIZLuuMJPq5DJ
NjvhmK++qCcTQrJo/4TMVoWmcZZKR3XzcSs++HYRELNCwcM2q9s07R4KkV81aB0t
RpCaCWa2KVUCrKdk3FlnG5pS7A6US5KGP4g6sSQRnq8t3IYDUbDo5Q==
=Bte8
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The third "new features" pull request for v6.8. This is a smaller one
to clear up our tree before the break and nothing really noteworthy
this time.
Major changes:
stack
* cfg80211: introduce cfg80211_ssid_eq() for SSID matching
* cfg80211: support P2P operation on DFS channels
* mac80211: allow 64-bit radiotap timestamps
iwlwifi
* AX210: allow concurrent P2P operation on DFS channels
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle a case of time overflow, where the switch time might
be smaller than the partial TSF in the beacon.
Additionally, apply advertised TTLM earlier in order to be
ready on time on the newly activated links.
Fixes: 702e80470a ("wifi: mac80211: support handling of advertised TID-to-link mapping")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.15079c34e5c8.I0dd50bcceff5953080cdd7aee5118b72c78c6507@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may support concurrent DFS operation which relies on the
BSS channel width for its relaxations. Notify cfg80211 about BW change
so it can schedule regulatory checks.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231220133549.e08f8e9ebc67.If8915d13e203ebd380579f55fd9148e9b3f43306@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is possible for the TX status report for the (Re)Association Request
frame to be delayed long enough for the AP's (Re)Association Response
frame to be received and processed before it. If that were to happen for
a case where the AP rejects the association with indication to come back
later, the association timeout and retry state should not be modified
anymore with the TX status information that would be processed after
this. Updating the association timeout in such a reverse order of events
could result in shortening the timeouts for the association comeback
mechanism and that could result in the association failing.
Track whether we have already processed association rejection with
comeback time and if so, skip the timeout and retry update on any
following TX status report.
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Link: https://msgid.link/20231219174814.2581575-1-j@w1.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ESS capability bit is reserved in frames transmitted by
the client, so we shouldn't set it. Since we've set it for
decades, keep that old behaviour unless we're connection to
a new EHT AP.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.65005aba900b.I3d00c8741400572a89a7508b5ae612c968874ad7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There may be cases where puncturing isn't possible, and
a connection needs to be downgraded. Add a hardware flag
to support this.
This is likely temporary: it seems we will need to move
puncturing to the chandef/channel context.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.c1e89ea55e93.I37b8ca0ee64d5d7699e351785a9010afc106da3c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to check that cfg80211_defragment_element()
didn't return an error, since it can fail due to bad
input, and we didn't catch that before.
Fixes: 8eb8dd2ffb ("wifi: mac80211: Support link removal using Reconfiguration ML element")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231211085121.8595a6b67fc0.I1225edd8f98355e007f96502e358e476c7971d8c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
make htmldocs warns:
Documentation/driver-api/80211/cfg80211:48: ./include/net/cfg80211.h:7290: WARNING: Duplicate C declaration, also defined at cfg80211:7251.
Declaration is '.. c:function:: void cfg80211_rx_assoc_resp (struct net_device *dev, struct cfg80211_rx_assoc_resp *data)'.
This is because there's a function named cfg80211_rx_assoc_resp() and a struct
named cfg80211_rx_assoc_resp, see previous patch for more info.
To workaround this rename the struct to cfg80211_rx_assoc_resp_data. The
parameter for the function is named 'data' anyway so the naming here is
consistent.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231012114229.2931808-3-kvalo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we are moving to MLO and links terms, also the airtime protection
will be done for a link rather than for a vif. Thus, some
drivers will need to know for which link to protect airtime.
Add link id as a parameter to the mgd_prepare_tx() callback.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.c7fc59a6780b.Ic88a5037d31e184a2dce0b031ece1a0a93a3a9da@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If there is a disassoc before the fisrt beacon we need to protect a
session for the deauth frame. Currently we are checking if we had a
beacon in the default link, which is wrong in a MLO connection and
link id != 0.
Fix this by checking all the active links, if none had a beacon then
protect a session.
If at least one link had a beacon there is no need for session
protection.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231004120820.d290f0ab77b0.Ic1505cf3d60f74580d31efa7e52046947c490b85@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the association command fails then the authentication is still valid
and it makes sense to keep it alive. Otherwise, we would currently get
into an inconsistent state because mac80211 on the one hand is
disconnected but on the other hand the state is not entirely cleared
and a new authentication could not continue.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230928172905.c9855f46ebc8.I7f3dcd4120a186484a91b87560e9b7201d40984f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resolve several conflicts, mostly between changes/fixes in
wireless and the locking rework in wireless-next. One of
the conflicts actually shows a bug in wireless that we'll
want to fix separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Looks like I lost that by accident, add it back.
Fixes: 076fc8775d ("wifi: cfg80211: remove wdev mutex")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When associating to an MLD AP, links may be disabled. Create all
resources associated with a disabled link so that we can later enable it
without having to create these resources on the fly.
Fixes: 6d543b34db ("wifi: mac80211: Support disabled links during association")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://lore.kernel.org/r/20230925173028.f9afdb26f6c7.I4e6e199aaefc1bf017362d64f3869645fa6830b5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reject configuring a channel for MLO if either EHT is not supported or
the BSS does not have the correct ML element. This avoids trying to do
a multi-link association with a misconfigured AP.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230920211508.80c3b8e5a344.Iaa2d466ee6280994537e1ae7ab9256a27934806f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With this cfg80211 can report the link that caused the error to
userspace which is then able to react to it by e.g. removing the link
from the association and retrying.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230920211508.275fc7f5c426.I8086c0fdbbf92537d6a8b8e80b33387fcfd5553d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support handling of advertised TID-to-link mapping elements received
in a beacon.
These elements are used by AP MLD to disable specific links and force
all clients to stop using these links.
By default if no TID-to-link mapping is advertised, all TIDs shall be
mapped to all links.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230920211508.623c4b692ff9.Iab0a6f561d85b8ab6efe541590985a2b6e9e74aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Connection to an AP that is running a CSA flow may end up with a
failure as the AP might change its channel during the connection
flow while we do not track the channel change yet.
Avoid that by rejecting a connection to such an AP.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230920211508.e5001a762a4a.I9745c695f3403b259ad000ce94110588a836c04a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cisco AP module 9115 with FW 17.3 has a bug and sends a too
large maximum MPDU length in the association response
(indicating 12k) that it cannot actually process.
Work around that by taking the minimum between what's in the
association response and the BSS elements (from beacon or
probe response).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230918140607.d1966a9a532e.I090225babb7cd4d1081ee9acd40e7de7e41c15ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We really cannot even get into this as we can't have
a BSS with a 5/10 MHz (scan) width, and therefore all
the code handling shifted rates cannot happen. Remove
it all, since it's broken anyway, at least with MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code that sets up the assoc link will currently take the BSS
element data from the beacon only. This is correct for some of
the data, notably the timing and the "have_beacon", but all the
data about MBSSID and EHT really doesn't need to be taken from
there, and if the EHT puncturing is misconfigured on the AP but
we didn't receive a beacon yet, this causes us to connect but
immediately disconnect upon receiving the first beacon, rather
than connecting without EHT in the first place.
Change the code to take MBSSID and EHT data also from the probe
response, for a better picture of what the BSS capabilities are
and to avoid that EHT puncturing problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230827135854.3c7e52d49482.Iba6b672f6dc74b45bba26bc497e953e27da43ef9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows to finalize the CSA per link.
In case the switch didn't work, tear down the MLD connection.
Also pass the ieee80211_bss_conf to post_channel_switch to let the
driver know which link completed the switch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230828130311.3d3eacc88436.Ic2d14e2285aa1646216a56806cfd4a8d0054437c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When connect to MLO AP with more than one link, and the assoc response of
AP is not success, then cfg80211_unhold_bss() is not called for all the
links' cfg80211_bss except the primary link which means the link used by
the latest successful association request. Thus the hold value of the
cfg80211_bss is not reset to 0 after the assoc fail, and then the
__cfg80211_unlink_bss() will not be called for the cfg80211_bss by
__cfg80211_bss_expire().
Then the AP always looks exist even the AP is shutdown or reconfigured
to another type, then it will lead error while connecting it again.
The detail info are as below.
When connect with muti-links AP, cfg80211_hold_bss() is called by
cfg80211_mlme_assoc() for each cfg80211_bss of all the links. When
assoc response from AP is not success(such as status_code==1), the
ieee80211_link_data of non-primary link(sdata->link[link_id]) is NULL
because ieee80211_assoc_success()->ieee80211_vif_update_links() is
not called for the links.
Then struct cfg80211_rx_assoc_resp resp in cfg80211_rx_assoc_resp() and
struct cfg80211_connect_resp_params cr in __cfg80211_connect_result()
will only have the data of the primary link, and finally function
cfg80211_connect_result_release_bsses() only call cfg80211_unhold_bss()
for the primary link. Then cfg80211_bss of the other links will never free
because its hold is always > 0 now.
Hence assign value for the bss and status from assoc_data since it is
valid for this case. Also assign value of addr from assoc_data when the
link is NULL because the addrs of assoc_data and link both represent the
local link addr and they are same value for success connection.
Fixes: 81151ce462 ("wifi: mac80211: support MLO authentication/association with one link")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Link: https://lore.kernel.org/r/20230825070055.28164-1-quic_wgong@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're now protecting everything with the wiphy mutex
(and were really using it for almost everything before),
there's no longer any real reason to have a separate wdev
mutex. It may feel better, but really has no value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the iflist_mtx, so we don't need this mutex any
more in mac80211. However, drivers may also iterate,
and in some cases (e.g. mt76) do so from high-priority
contexts. Thus, keep the mutex around but remove its
usage in mac80211 apart from those driver-visible parts
that are still needed.
Most of this change was done automatically with spatch,
with the parts that are still needed as described above
reverted manually.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the local->mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the chanctx_mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the sta_mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One more work that will now execute with the wiphy
locked, for future cleanups.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Again, to have the wiphy locked for it.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Along with everything else, move the dynamic PS work
to be a wiphy work, to simplify locking later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Again this serves to simplify the locking in mac80211
in the future, since this is a relatively complex work.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the DFS CAC work over to hold the wiphy lock
there without worry about work cancellation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current SMPS status handling isn't per link, so we only
ever change the deflink, which is obviously wrong, it's not
even used for multi-link connections, but the request API
actually includes the link ID.
Use the new status_data changes to move the handling to the
right link, this also saves parsing the frame again on the
status report, instead we can now check only if it was an
SMPS frame.
Of course, move the worker to be a wiphy work so that we're
able to cancel it safely for the link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving a multi-link association response, make sure to
track the BSS parameter change count for each link, including
the assoc link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230619161906.1799c164e7e9.I8e2c1f5eec6eec3fab525ae2dead9f6f099a2427@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jakub Kicinski
Johannes Berg
Richard Kinder
Ayala Beker
Benjamin Berg
Anjaneyulu
Miri Korenblit
Aditya Kumar Singh
David S. Miller
Paolo Abeni
Andrei Otcheretianski
Jouni Malinen
Kalle Valo
Ilan Peer
Emmanuel Grumbach
Wen Gong