Currently, with MFD/pin assignment D, the driver clears the pipe reset bit
of lane 1 which is not owned by display. This causes the display
to block S0iX.
By not clearing this bit for lane 1 and keeping whatever default, S0ix
started to work. This is already what the driver does at the end
of the phy lane reset sequence (Step#8)
Bspec: 65451
Fixes: 619a06dba6 ("drm/i915/mtl: Reset only one lane in case of MFD")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231005001310.154396-1-khaled.almahallawy@intel.com
There was a recent update in the BSpec adding an extra step to the PLL
enable sequence, which is for programming the msgbus timer. Since we
also touch PHY registers during hw readout, let's do the programming
when starting a transaction rather than only when doing the PLL enable
sequence.
This might be the missing step that was causing the timeouts
that we have recently seen during C20 SRAM register programming
sequences. With this in place, we shouldn't need the logic to bump the
timer thresholds, since now we have a documented value that should be
set peform programming the registers. As such, let's also remove
intel_cx0_bus_check_and_bump_timer(), but keep the part that checks if
hardware really detected a timeout, which might be useful debugging
information.
v2:
- Use debug level instead of warning for the message notifying that
the hardware did not detect the timeout. (Mika)
- Got a new BSpec update clarifying that we need to program the msgbus
timer of both PHY lanes. Update the changes to reflect that.
(Gustavo)
BSpec: 64568
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230912155923.39494-1-gustavo.sousa@intel.com
We have experienced timeout issues when going through the sequence to
access C20 SRAM registers. Experimentation showed that bumping the
message bus timer threshold helped on getting display Type-C connection
on the C20 PHY to work.
While the timeout is still under investigation with the HW team, having
logic to allow forward progress (with the proper warnings) seems useful.
Thus, let's bump the threshold when a timeout is detected.
The bumped value of 0x200 pclk cycles was somewhat arbitrary - 2x the
default value. That value was successfully tested on real hardware that
was displaying timeouts otherwise.
v2:
- Reword commit message to indicate that access to C20 SRAM registers
is not direct. (Radhakrishna)
- Prefer not to use REG_FIELD_PREP() in intel_cx0_phy.c.
(Radhakrishna)
- Simplify intel_cx0_bus_check_and_bump_timer() to use a fixed bumped
value instead of progressively increasing the threshold. (Mika)
BSpec: 65156
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230830121524.15101-1-gustavo.sousa@intel.com
It is irrelevant for the caller that the max lane count is being
derived from a FIA register, so having "fia" in the function name is
irrelevant. Rename the function accordingly.
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825081638.275795-5-luciano.coelho@intel.com
Most of the IS_METEORLAKE checks in the display code shouldn't actually
be tied to MTL as a platform, but rather to the Xe_LPD+ display IP
(which is used in MTL, but may show up again in future platforms). In
cases where we're trying to match that specific IP, use a version check
against IP_VER(14, 0). For cases where we're just handling new behavior
introduced by this IP (but which may also be inherited by future IP as
well), use a ver >= 14 check.
The one exception here is the stolen memory workaround Wa_13010847436
(which is mislabelled as "Wa_22018444074" in the code). That's truly a
MTL-specific issue rather than being tied to any of the IP blocks, so
leaving the condition as IS_METEORLAKE is correct there.
v2:
- cdclk check should be >=, not >. (Gustavo)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230821180619.650007-19-matthew.d.roper@intel.com
According to the BSpec, voltage swing programming should be done for
owned PHY lanes. Do not program a not-owned PHY lane.
BSpec: 74103, 74104
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814131331.69516-5-gustavo.sousa@intel.com
It is possible to generalize the "disable" value for the transmitters to
be a bit mask based on the port width and the port reversal boolean,
with a small exception for DP-alt mode with "x1" port width.
Simplify the code by using such a mask and a for-loop instead of using
switch-case statements.
v2:
- Use (i < 2) instead of (i / 2 == 0) for PHY lane mask selection.
(Jani)
BSpec: 64539
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814131331.69516-3-gustavo.sousa@intel.com
There are more parts of C10/C20 programming that need to take owned
lanes into account. Define the function intel_cx0_get_owned_lane_mask()
and use it. There will be new users of that function in upcoming
changes.
BSpec: 64539
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814131331.69516-2-gustavo.sousa@intel.com
Driver does not clear the default SSC for MPLLA. This causes link training
failure when trying to use 10G and 20G rates. Fix the behaviour and enable
ssc only when we really want.
Fixes: 237e7be0bf ("drm/i915/mtl: For DP2.0 10G and 20G rates use MPLLA")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Clint Taylor <Clinton.A.Taylor@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616043950.1576836-1-radhakrishna.sripada@intel.com
From PICA message bus we wait for acknowledgment from
read/write commands. In case of an error, we reset the
bus for the next command.
Current implementation ends up resetting message bus twice
in cases where error is not the timeout. Since, we only need
to reset message bus once, let's move reset to corresponding
timeout error and drop the excess reset function calls from
read/write functions.
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230609122130.69794-1-mika.kahola@intel.com
In case when only two or less transmit lanes are owned such as MFD
(DP-alt with x2 lanes) we need to reset only one data lane (lane0).
With only x2 lanes we don't need to poll for the phy current
status on both data lanes since only the owned data lane will respond.
v2: Find better naming for lanes and revise the commit message (Luca)
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com> (v1)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com> (v2)
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230601101314.332392-1-mika.kahola@intel.com
While disabling Thunderbolt PLL, we request PLL to be stopped and
wait for ACK bit to be cleared. The expected value should be '0'
instead of '~XELPDP_TBT_CLOCK_ACK' or otherwise we incorrectly
receive dmesg warn "PHY PLL not unlocked in 10us".
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512120003.587360-1-mika.kahola@intel.com
Add i915 parameter to I915_STATE_WARN() and use device based logging.
Done using cocci + hand edited where there was no i915 local variable
ready.
v2: avoid null deref in verify_connector_state()
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230512181658.1735594-1-jani.nikula@intel.com
Add register writes to enable powering up Type-C subsystem i.e. TCSS.
For MeteorLake we need to request TCSS to power up and check the TCSS
power state after 500 us.
In addition, for PICA we need to set/clear the Type-C PHY ownnership
bit when Type-C device is connected/disconnected.
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-11-mika.kahola@intel.com
Use MPLLA for DP2.0 rates 10G and 20G, when ssc is enabled.
v2: Fix typo in commit message (Animesh)
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-7-mika.kahola@intel.com
As we already do with C10 chip, let's dump the pll
hw state for C20 as well.
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-4-mika.kahola@intel.com
Create a table for C20 DP1.4, DP2.0 and HDMI2.1 rates.
The PLL settings are based on table, not for algorithmic alternative.
For DP 1.4 only MPLLB is in use.
Once register settings are done, we read back C20 HW state.
BSpec: 64568
v2: Updated pll tables (RK)
MPLLB selection fix (RK)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-3-mika.kahola@intel.com
C20 phy PLL programming sequence for DP, DP2.0, HDMI2.x non-FRL and
HDMI2.x FRL. This enables C20 MPLLA and MPLLB programming sequence. add
4 lane support for c20.
v2: Add 6.48Gbps and 6.75Gbps modes for eDP (RK)
Fix lane check (RK)
Fix multiline commenting (Arun)
use usleep_range() instead of msleep() (Andi)
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230428095433.4109054-2-mika.kahola@intel.com
intel_{mpllb,c10pll}_state_verify() blows up if you call them
for a non-modeset/fastset commit on account of the relevant
connector not being part of the overall atomic state.
Currently the state checker only runs for modeset/fastset
commits, but for testing purposes it is sometimes desirable
to run it for other commits too. Check for modeset/fastset
in intel_{mpllb,c10pll}_state_verify() itself to make this safe.
v2: Give the new intel_c10pll_state_verify() the same treatment
Add comment to explain why we do this
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230414190159.7904-1-ville.syrjala@linux.intel.com
Like DG2, we still don't have a proper algorithm that can be used
for calculating PHY settings, but we do have tables of register
values for a handful of the more common link rates. Some support is
better than none, so let's go ahead and add/use these tables when we
can, and also add some logic to hdmi_port_clock_valid() to filter the
modelist to just the modes we can actually support with these link
rates.
Hopefully we'll have a proper / non-encumbered algorithm to calculate
these registers by the time we upstream and we'll be able to replace
this patch with something more general purpose.
Bspec: 64568
v2: Rebasing with Clint's HDMI C10 PLL tables (Mika)
v3: Remove the extra hdmi clock check pruning.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-8-radhakrishna.sripada@intel.com
C10 phys uses direct mapping internally for voltage and pre-emphasis levels.
Program the levels directly to the fields in the VDR Registers.
Bspec: 65449
v2: From table "C10: Tx EQ settings for DP 1.4x" it shows level 1
and preemphasis 1 instead of two times of level 1 preemphasis 0.
Fix this in the driver code as well.
v3: VSwing update (Clint)
v4: Add vboost termination ctl programming(Imre)
Fix tx llogic and other nits
Restrict C10 vdr ctl register access for C10 phy(RK)
v5: Program vboots, termination ctl for both lanes(Imre)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>(v3)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-5-radhakrishna.sripada@intel.com
XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
Ville Syrjälä
Khaled Almahallawy
Gustavo Sousa
Luca Coelho
Matt Roper
Radhakrishna Sripada
Mika Kahola
Clint Taylor
Jani Nikula