When netdev_notify_peers was substituted in
commit 986103e792 ("net/ibmvnic: Fix RTNL deadlock during device reset"),
call_netdevice_notifiers(NETDEV_RESEND_IGMP, dev) was missed.
Fix it now.
Fixes: 986103e792 ("net/ibmvnic: Fix RTNL deadlock during device reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reduce the amount of time spent replenishing RX buffers by only doing
so once available buffers has fallen under a certain threshold, in this
case half of the total number of buffers, or if the polling loop exits
before the packets processed is less than its budget. Non-exhaustion of
NAPI budget implies lower incoming packet pressure, allowing the leeway
to refill the buffers in preparation for any impending burst.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Take advantage of the additional optimizations in netdev_alloc_skb when
allocating socket buffers to be used for packet reception.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the current NAPI polling loop exits without completing it's
budget, only re-enable interrupts if there are no entries remaining
in the queue and napi_complete_done is successful. If there are entries
remaining on the queue that were missed, restart the polling loop.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PCI bus slowdowns were observed on IBM VNIC devices as a result
of partial cache line writes and non-cache aligned full cache line writes.
Ensure that packet data buffers are cache-line aligned to avoid these
slowdowns.
Signed-off-by: Dwip N. Banerjee <dnbanerg@us.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is not longer used, so remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unused and superfluous code and members in
existing TX implementation and data structures.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Include support for the xmit_more feature utilizing the
H_SEND_SUB_CRQ_INDIRECT hypervisor call which allows the sending
of multiple subordinate Command Response Queue descriptors in one
hypervisor call via a DMA-mapped buffer. This update reduces hypervisor
calls and thus hypervisor call overhead per TX descriptor.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Utilize the H_SEND_SUB_CRQ_INDIRECT hypervisor call to send
multiple RX buffer descriptors to the device in one hypervisor
call operation. This change will reduce the number of hypervisor
calls and thus hypervisor call overhead needed to transmit
RX buffer descriptors to the device.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch introduces the infrastructure to send batched subordinate
Command Response Queue descriptors, which are used by the ibmvnic
driver to send TX frame and RX buffer descriptors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Acked-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 5a18e1e0c1 introduced the 'failover_pending' state to track
the "failover pending window" - where we wait for the partner to become
ready (after a transport event) before actually attempting to failover.
i.e window is between following two events:
a. we get a transport event due to a FAILOVER
b. later, we get CRQ_INITIALIZED indicating the partner is
ready at which point we schedule a FAILOVER reset.
and ->failover_pending is true during this window.
If during this window, we attempt to open (or close) a device, we pretend
that the operation succeded and let the FAILOVER reset path complete the
operation.
This is fine, except if the transport event ("a" above) occurs during the
open and after open has already checked whether a failover is pending. If
that happens, we fail the open, which can cause the boot scripts to leave
the interface down requiring administrator to manually bring up the device.
This fix "extends" the failover pending window till we are _actually_
ready to perform the failover reset (i.e until after we get the RTNL
lock). Since open() holds the RTNL lock, we can be sure that we either
finish the open or if the open() fails due to the failover pending window,
we can again pretend that open is done and let the failover complete it.
We could try and block the open until failover is completed but a) that
could still timeout the application and b) Existing code "pretends" that
failover occurred "just after" open succeeded, so marks the open successful
and lets the failover complete the open. So, mark the open successful even
if the transport event occurs before we actually start the open.
Fixes: 5a18e1e0c1 ("ibmvnic: Fix failover case for non-redundant configuration")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Acked-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20201030170711.1562994-1-sukadev@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski brought up a concern in ibmvnic_set_mac().
ibmvnic_set_mac() does this:
ether_addr_copy(adapter->mac_addr, addr->sa_data);
if (adapter->state != VNIC_PROBED)
rc = __ibmvnic_set_mac(netdev, addr->sa_data);
So if state == VNIC_PROBED, the user can assign an invalid address to
adapter->mac_addr, and ibmvnic_set_mac() will still return 0.
The fix is to validate ethernet address at the beginning of
ibmvnic_set_mac(), and move the ether_addr_copy to
the case of "adapter->state != VNIC_PROBED".
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201027220456.71450-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After mac address change request completes successfully, the new mac
address need to be saved to adapter->mac_addr as well as
netdev->dev_addr. Otherwise, adapter->mac_addr still holds old
data.
Fixes: 62740e9788 ("net/ibmvnic: Update MAC address settings after adapter reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201020223919.46106-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Factor send_control_ip_offload out of handle_query_ip_offload_rsp.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor send_query_ip_offload out of handle_request_cap_rsp to
pair with handle_query_ip_offload_rsp.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new name send_query_map pairs with handle_query_map_rsp.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new name send_request_cap pairs with handle_request_cap_rsp.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new name send_query_cap pairs with handle_query_cap_rsp.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set up the speed according to crq->query_phys_parms.rsp.speed.
Fix IBMVNIC_10GBPS typo.
Fixes: f8d6ae0d27 ("ibmvnic: Report actual backing device speed and duplex values")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 550f4d46af.
adapter->from_passive_init may be changed in ibmvnic_handle_crq
while ibmvnic_reset_init is waiting for the completion of
adapter->init_done.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indentation and logic clearly show that this code is missing
parenthesis.
Fixes: 9f13457377 ("ibmvnic fix NULL tx_pools and rx_tools issue at do_reset")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In some cases, the device or firmware may be busy when the
driver attempts to perform the CRQ initialization handshake.
If the partner is busy, the hypervisor will return the H_CLOSED
return code. The aim of this patch is that, if the device is not
ready, to query the device a number of times, with a small wait
time in between queries. If all initialization requests fail,
the driver will remain in a dormant state, awaiting a signal
from the device that it is ready for operation.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions share the majority of the code, hence merge
them together. In the meanwhile, add a reset pass-in parameter
to differentiate them. Thus, the code is easier to read and to tell
the difference between reset_init and regular init.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the beginning of the function, from_passive_init is set false by
"adapter->from_passive_init = false;",
hence the if statement will never run.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When H_SEND_CRQ command returns with H_CLOSED, it means the
server's CRQ is not ready yet. Instead of resetting immediately,
we wait for the server to launch passive init.
ibmvnic_init() and ibmvnic_reset_init() should also return the
error code from ibmvnic_send_crq_init() call.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of comparing (adapter->init_done_rc == 1), let it
be (adapter->init_done_rc == PARTIALSUCCESS).
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the time of do_rest, ibmvnic tries to re-initalize the tx_pools
and rx_pools to avoid re-allocating the long term buffer. However
there is a window inside do_reset that the tx_pools and
rx_pools were freed before re-initialized making it possible to deference
null pointers.
This patch fix this issue by always check the tx_pool
and rx_pool are not NULL after ibmvnic_login. If so, re-allocating
the pools. This will avoid getting into calling reset_tx/rx_pools with
NULL adapter tx_pools/rx_pools pointer. Also add null pointer check in
reset_tx_pools and reset_rx_pools to safe handle NULL pointer case.
Signed-off-by: Mingming Cao <mmc@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver reads RX and TX subCRQ handle array directly from
a DMA-mapped buffer address when it needs to make a H_SEND_SUBCRQ
hcall. This patch stores that information in the ibmvnic_sub_crq_queue
structure instead of reading from the buffer received at login. The
overall goal of this patch is to parse relevant information from the
login response buffer and store it in the driver's private data
structures so that we don't need to read directly from the buffer and
can then free up that memory.
Signed-off-by: Cristobal Forno <cforno12@linux.ibm.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX queue IRQ mappings are disposed in both the TX IRQ and RX IRQ
error paths. Fix this and dispose of TX IRQ mappings correctly in
case of an error.
Fixes: ea22d51a78 ("ibmvnic: simplify and improve driver probe function")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue the reset path when partner adapter is not ready or H_CLOSED is
returned from reset crq. This patch allows the CRQ init to proceed to
establish a valid CRQ for traffic to flow after reset.
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNIC driver's "login" command sequence is the final step
in the driver's initialization process with device firmware,
confirming the available device queue resources to be utilized
by the driver. Under high system load, firmware may not respond
to the request in a timely manner or may abort the request. In
such cases, the driver should reattempt the login command
sequence. In case of a device error, the number of retries
is bounded.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that all scheduled work items have completed before continuing
with device removal and after further event scheduling has been
halted. This patch fixes a bug where a scheduled driver reset event
is processed following device removal.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNIC protocol version is reported in big-endian format, but it
is not byteswapped before logging. Fix that, and remove version
comparison as only one protocol version exists at this time.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During MTU change, the following events may happen.
Client-driven CRQ initialization fails due to partner’s CRQ closed,
causing client to enqueue a reset task for FATAL_ERROR. Then passive
(server-driven) CRQ initialization succeeds, causing client to
release CRQ and enqueue a reset task for failover. If the passive
CRQ initialization occurs before the FATAL reset task is processed,
the FATAL error reset task would try to access a CRQ message queue
that was freed, causing an oops. The problem may be most likely to
occur during DLPAR add vNIC with a non-default MTU, because the DLPAR
process will automatically issue a change MTU request.
Fix this by not processing fatal error reset if CRQ is passively
initialized after client-driven CRQ initialization fails.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver does not check the device state when the device
is removed. If the device is removed while a device reset is being
processed, the remove may free structures needed by the reset,
causing an oops.
Fix this by checking the device state before processing device remove.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This conditional is missing a bang, with the intent
being to break when the retry count reaches zero.
Fixes: 476d96ca9c ("ibmvnic: Bound waits for device queries")
Suggested-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Provide some serialization for device CRQ commands
and queries to ensure that the shared variable used for
storing return codes is properly synchronized.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a wrapper for wait_for_completion calls with additional
driver checks to ensure that the driver does not wait on a
disabled device. In those cases or if the device does not respond
in an extended amount of time, this will allow the driver an
opportunity to recover.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we receive a notification that the device has been deactivated
or removed, force a completion of all waiting threads.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix multiple calls to init_completion for device completion
structures. Instead, initialize them during device probe and
reinitialize them later as needed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reversion of commit 11d49ce9f7
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) leaves us
calling H_EOI even in XIVE mode. That will fail with H_FUNCTION
because H_EOI is not supported in that mode. That failure is
harmless. Ignore it so we can use common code for both XICS and
XIVE.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 11d49ce9f7
(“net/ibmvnic: Fix EOI when running in XIVE mode.”) since that
has the unintended effect of changing the interrupt priority
and emits warning when running in legacy XICS mode.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pSeries machines on POWER9 processors can run with the XICS (legacy)
interrupt mode or with the XIVE exploitation interrupt mode. These
interrupt contollers have different interfaces for interrupt
management : XICS uses hcalls and XIVE loads and stores on a page.
H_EOI being a XICS interface the enable_scrq_irq() routine can fail
when the machine runs in XIVE mode.
Fix that by calling the EOI handler of the interrupt chip.
Fixes: f23e0643cd ("ibmvnic: Clear pending interrupt after device reset")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code allows more than one thread to run in reset. This can
corrupt struct adapter data. Check adapter->resetting before performing
a reset, if there is another reset running delay (100 msec) before trying
again.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
made the change to hold the RTNL lock during a reset to avoid deadlock
but linkwatch_event is fired during the reset and needs the RTNL lock.
That keeps linkwatch_event process from proceeding until the reset
is complete. The reset process cannot tolerate the linkwatch_event
processing after reset completes, so release the RTNL lock during the
process to allow a chance for linkwatch_event to run during reset.
This does not guarantee that the linkwatch_event will be processed as
soon as link state changes, but is an improvement over the current code
where linkwatch_event processing is always delayed, which prevents
transmissions on the device from being deactivated leading transmit
watchdog timer to time-out.
Release the RTNL lock before link state change and re-acquire after
the link state change to allow linkwatch_event to grab the RTNL lock
and run during the reset.
Fixes: a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit 0655f9943d ("net/ibmvnic: Update carrier state after link
state change") we are now able to detect when the carrier is properly
present in the device, so only report an unexpected unknown speed when it
is properly detected. Unknown speed is expected to be seen by the device
in case the backing device has no link detected.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Commit 1c2977c094 ("net/ibmvnic: free reset work of removed device from queue")
adds a } without corresponding { causing build break.
Fixes: 1c2977c094 ("net/ibmvnic: free reset work of removed device from queue")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Reviewed-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 36f1031c51 ("ibmvnic: Do not process reset during or after
device removal") made the change to exit reset if the driver has been
removed, but does not free reset work items of the adapter from queue.
Ensure all reset work items are freed when breaking out of the loop early.
Fixes: 36f1031c51 ("ibmnvic: Do not process reset during or after device removal”)
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to wait until a completion is received to unmap
TX descriptor buffers that have been passed to the hypervisor.
Instead unmap it when the hypervisor call has completed. This patch
avoids the possibility that a buffer will not be unmapped because
a TX completion is lost or mishandled.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Devesh K. Singh <devesh_singh@in.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return values for these memory allocations are unchecked,
which may cause an oops if the driver does not handle them after
a failure. Fix by checking the function's return code.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was observed that multicast packets were no longer received after
a device reset. The fix is to resend the current multicast list to
the backing device after recovery.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check driver state before halting it during a reset. If the driver is
not running, do nothing. Otherwise, a request to deactivate a down link
can cause an error and the reset will fail.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190523091650.663497195@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only set the device carrier state to on after receiving an up link
state indication from the underlying adapter. Likewise, if a down
link indication is receieved, update the carrier state accordingly.
This fix ensures that accurate carrier state is reported by the driver
following a link state update by the underlying adapter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was discovered in testing that the underlying hardware MAC
address will revert to initial settings following a device reset,
but the driver fails to resend the current OS MAC settings. This
oversight can result in dropped packets should the scenario occur.
Fix this by informing hardware of current MAC address settings
following any adapter initialization or resets.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver currently uses the same fixed name when using
request_irq, this makes it hard to parse when multiple VNIC devices are
available at the same time. This patch adds the unit_address as the device
identification along with an id for each queue.
The original idea was to use the interface name as an identifier, but it
is not feasible given these requests happen at adapter probe, and at this
point netdev is not yet registered so it doesn't have the proper name
assigned to it.
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While determining offload capabilities of backing hardware during
a device reset, the driver is clobbering current feature settings.
Update hw_features on reset instead of features unless a feature
is enabled that is no longer supported on the current backing device.
Also enable features that were not supported prior to the reset but
were previously enabled or requested by the user.
This can occur if the reset is the result of a carrier change, such
as a device failover or partition migration.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Generic Receive Offload in the ibmvnic driver.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/ibm/ibmvnic.c: In function '__ibmvnic_reset':
drivers/net/ethernet/ibm/ibmvnic.c:1971:21: warning: variable 'netdev' set but not used [-Wunused-but-set-variable]
It's never used since introduction in
commit ed651a1087 ("ibmvnic: Updated reset handling")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic driver currently reports a fixed value for both speed and
duplex settings regardless of the actual backing device that is being
used. By adding support to the QUERY_PHYS_PARMS command defined by the
PAPR+ we can query the current physical port state and report the proper
values for these feilds.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was checking for non-NULL address.
- adapter->napi[i]
This is pointless as these will be always non-NULL, since the
'dapter->napi' is allocated in init_napi().
It is safe to get rid of useless checks for addresses to fix the
coccinelle warning:
>>drivers/net/ethernet/ibm/ibmvnic.c: test of a variable/field address
Since such statements always return true, they are redundant.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Thomas Falcon <tlfalcon@linux.ibm.com>
CC: John Allen <jallen@linux.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linuxppc-dev@lists.ozlabs.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5681e20b5 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.
Fixes: a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device reset, queue memory is not being updated to accommodate
changes in ring buffer sizes supported by backing hardware. Track
any differences in ring buffer sizes following the reset and update
queue memory when possible.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong index is used when cleaning up RX buffer objects during release
of RX queues. Update to use the correct index counter.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes to use rtnl_lock only during a reset to avoid
deadlock that could occur when a thread operating close is holding
rtnl_lock and waiting for reset_lock acquired by another thread,
which is waiting for rtnl_lock in order to set the number of tx/rx
queues during a reset.
Also, we now setting the number of tx/rx queues during a soft reset
for failover or LPM events.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't request tag insertion when it isn't present in outgoing skb.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
When choosing channel amounts and ring sizes, the maximums in the
ibmvnic driver are defined by the virtual i/o server management
partition. Even though they are defined as maximums, the client
driver may in fact successfully request resources that exceed
these limits, which are mostly dependent on a user's hardware
With this in mind, provide an ethtool flag that when enabled will
allow the user to request resources limited by driver-defined
maximums instead of limits defined by the management partition.
The driver will try to honor the user's request but may not allowed
by the management partition. In this case, the driver requests
as close as it can get to the desired amount until it succeeds.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As diagnosed by Song Liu, ndo_poll_controller() can
be very dangerous on loaded hosts, since the cpu
calling ndo_poll_controller() might steal all NAPI
contexts (for all RX/TX queues of the NIC). This capture
can last for unlimited amount of time, since one
cpu is generally not able to drain all the queues under load.
ibmvnic uses NAPI for TX completions, so we better let core
networking stack call the napi->poll() to avoid the capture.
ibmvnic_netpoll_controller() was completely wrong anyway,
as it was scheduling NAPI to service RX queues (instead of TX),
so I doubt netpoll ever worked on this driver.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Cc: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the return codes of these functions and halt reset
in case of failure. The driver will remain in a dormant state
until the next reset event, when device initialization will be
re-attempted.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print a string instead of the error code. Since there is a
possibility that the driver can recover, classify it as a
warning instead of an error.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When backing device firmware reports an error, it provides an
error ID, which is meant to be queried for more detailed error
information. Currently, however, an error ID is not provided by
the Virtual I/O server and there are not any plans to do so. For
now, it is always unfilled or zero, so request_error_information
will never be called. Remove it.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In its current state, the driver will handle backing device
login in a loop for a certain number of retries while the
device returns a partial success, indicating that the driver
may need to try again using a smaller number of resources.
The variable it checks to continue retrying may change
over the course of operations, resulting in reallocation
of resources but exits without sending the login attempt.
Guard against this by introducing a boolean variable that
will retain the state indicating that the driver needs to
reattempt login with backing device firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a recovery hard reset to handle reset failure as a result of
change of device context following a transport event, such as a
backing device failover or partition migration. These operations reset
the device context to its initial state. If this occurs during a reset,
any initialization commands are likely to fail with an invalid state
error as backing device firmware requests reinitialization.
When this happens, make one more attempt by performing a hard reset,
which frees any resources currently allocated and performs device
initialization. If a transport event occurs during a device reset, a
flag is set which will trigger a new hard reset following the
completionof the current reset event.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set device resetting state at the earliest possible point: as soon as a
reset is successfully scheduled. The reset state is toggled off when
all resets have been processed to completion.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having one initialization routine for all cases, create
a separate, simpler function for standard initialization, such as during
device probe. Use the original initialization function to handle
device reset scenarios. The goal of this patch is to avoid having
a single, cluttered init function to handle all possible
scenarios.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If setting the link state is not successful, print a warning
with the resulting return code and return it to be handled
by the caller.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device init is interrupted by a failover, set the init return
code so that it can be checked and handled appropriately by the
init routine.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether CRQ command is successful before awaiting a response
from the management partition. If the command was not successful, the
driver may hang waiting for a response that will never come.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lijun Pan
Dwip N. Banerjee
Thomas Falcon
Sukadev Bhattiprolu
David S. Miller
Allen Pais
Jakub Kicinski
Mingming Cao
Cristobal Forno
Dany Madden
Juliet Kim
Michael S. Tsirkin
Cédric Le Goater
Murilo Fossa Vicentini
Michal Suchanek
Jonathan Lemon
Thomas Gleixner
YueHaibing
Wen Yang
Michał Mirosław
Eric Dumazet
Thomas Falcon
John Allen