All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issues exist for
the addressed memory on the host i.e., memory is not cached. But in
reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the host.
And worst case, if the memory is cached on the host, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the host is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issue exist for
the addressed memory on the endpoint i.e., memory is not cached. But
in reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the endpoint.
And worst case, if the memory is cached on the endpoint, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the endpoint is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
8775 has IP version 1.34.0 so introduce a new cfg(cfg_1_34_0) for this
platform. Assign override_no_snoop flag into struct qcom_pcie_cfg and
set it true in cfg_1_34_0 and enable cache snooping if this particular
flag is true.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As like the 'epc_init' event, that is used to signal the EPF drivers about
the EPC initialization, let's introduce 'epc_deinit' event that is used to
signal EPC deinitialization.
The EPC deinitialization applies only when any sort of fundamental reset
is supported by the endpoint controller as per the PCIe spec.
Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1.
Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support
PERST# as the fundamental reset. So the 'deinit' event will be notified to
the EPF drivers when PERST# assert happens in the above mentioned EPC
drivers.
The EPF drivers, on receiving the event through the epc_deinit() callback
should reset the EPF state machine and also cleanup any configuration that
got affected by the fundamental reset like BAR, DMA etc...
This change also warrants skipping the cleanups in unbind() if already done
in epc_deinit().
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
The intent of the code snippet is to always return 0 for both
PCI_INTERRUPT_LINE and PCI_INTERRUPT_PIN.
The check misses PCI_INTERRUPT_PIN. This patch fixes that.
This is discovered by this call in VFIO:
pci_read_config_byte(vdev->pdev, PCI_INTERRUPT_PIN, &pin);
The old code does not set *val to 0 because it misses the check for
PCI_INTERRUPT_PIN. Garbage is returned in that case.
Fixes: 4daace0d8c ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lore.kernel.org/linux-pci/20240701202606.129606-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Cc: stable@kernel.org
Add support for r8a779g0 (R-Car V4H).
This driver previously supported r8a779f0 (R-Car S4-8). PCIe features
of both r8a779f0 and r8a779g0 are almost all the same. For example:
- PCI Express Base Specification Revision 4.0
- Root complex mode and endpoint mode are supported
However, r8a779g0 requires specific firmware to be provided, to
initialize the PHY. Otherwise, the PCIe controller will not work.
[kwilczynski: drop the proprietary firmware conversion comment]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-5-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Sequence for controlling the LTSSM state machine is going to change
for SoCs like r8a779f0. Move the LTSSM code to a new callback
ltssm_control() and populate it for each SoCs.
This also warrants the addition of new compatibles for r8a779g0 and
r8a779h0. But since they are already part of the DT binding, it won't
make any difference.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In order to support future SoCs such as r8a779g0 (R-Car V4H) and
r8a779h0 (R-Car V4M) that require different initialization settings,
introduce SoC specific driver data with the initial member being the
device mode.
No functional change.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
R-Car Gen4 PCIe controller needs to use the Synopsys-specific PCIe
configuration registers. So, add the macros.
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The struct mobiveil_rp_ops is not modified in this driver.
Thus, make this struct constant, which also moves data to a read-only
section decreasing object size and also improving overall security.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
4446 336 32 4814 12ce drivers/pci/controller/mobiveil/pcie-layerscape-gen4.o
After:
=====
text data bss dec hex filename
4454 328 32 4814 12ce drivers/pci/controller/mobiveil/pcie-layerscape-gen4.o
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/189fd881cc8fd80220e74e91820e12cf3a5be114.1719260294.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
'tegra_pcie_soc' has been unused since 56e15a238d ("PCI: tegra: Add
Tegra194 PCIe support"). Remove it.
Link: https://lore.kernel.org/r/20240527160118.37069-1-linux@treblig.org
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Use preserve_config in place of checking for PCI_PROBE_ONLY flag to enable
support for "linux,pci-probe-only" on a per host bridge basis.
This also obviates the use of adding PCI_REASSIGN_ALL_BUS flag if
!PCI_PROBE_ONLY, as pci_assign_unassigned_root_bus_resources() takes care
of reassigning the resources that are not already claimed.
Link: https://lore.kernel.org/r/20240508174138.3630283-5-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tegra194 and Tegra234 PCIe EP controllers have 64K alignment restriction
for the inbound ATU. Set the endpoint inbound ATU alignment to 64kB in the
Tegra194 PCIe driver.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Suggested-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Link: https://lore.kernel.org/linux-pci/20240508092207.337063-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Avoid large backtrace, it is sufficient to warn the user that there has
been a link problem. Either the link has failed and the system is in need
of maintenance, or the link continues to work and user has been informed.
The message from the warning can be looked up in the sources.
This makes an actual link issue less verbose.
First of all, this controller has a limitation in that the controller
driver has to assist the hardware with transition to L1 link state by
writing L1IATN to PMCTRL register, the L1 and L0 link state switching
is not fully automatic on this controller.
In case of an ASMedia ASM1062 PCIe SATA controller which does not support
ASPM, on entry to suspend or during platform pm_test, the SATA controller
enters D3hot state and the link enters L1 state. If the SATA controller
wakes up before rcar_pcie_wakeup() was called and returns to D0, the link
returns to L0 before the controller driver even started its transition to
L1 link state. At this point, the SATA controller did send an PM_ENTER_L1
DLLP to the PCIe controller and the PCIe controller received it, and the
PCIe controller did set PMSR PMEL1RX bit.
Once rcar_pcie_wakeup() is called, if the link is already back in L0 state
and PMEL1RX bit is set, the controller driver has no way to determine if
it should perform the link transition to L1 state, or treat the link as if
it is in L0 state. Currently the driver attempts to perform the transition
to L1 link state unconditionally, which in this specific case fails with a
PMSR L1FAEG poll timeout, however the link still works as it is already
back in L0 state.
Reduce this warning verbosity. In case the link is really broken, the
rcar_pcie_config_access() would fail, otherwise it will succeed and any
system with this controller and ASM1062 can suspend without generating
a backtrace.
Fixes: 84b5761462 ("PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()")
Link: https://lore.kernel.org/linux-pci/20240511235513.77301-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
plda_pcie_setup_iomems() needs the bridge->windows list from struct
pci_host_bridge and is currently used only by pcie-microchip-host.c. This
driver uses pci_host_common_probe(), which sets a pci_host_bridge as the
drvdata, so plda_pcie_setup_iomems() used platform_get_drvdata() to find
the pci_host_bridge.
But we also want to use plda_pcie_setup_iomems() in the new pcie-starfive.c
driver, which does not use pci_host_common_probe() and will have struct
starfive_jh7110_pcie as its drvdata, so pass the pci_host_bridge directly
to plda_pcie_setup_iomems() so it doesn't need platform_get_drvdata() to
find it.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-9-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log, reorder to where this is needed]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Add PLDA host plda_pcie_host_init()/plda_pcie_host_deinit() and map bus
function so vendors can use it to init PLDA PCIe host core.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-19-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mason Huo <mason.huo@starfivetech.com>
PLDA DMA interrupts are not all implemented, and the non-implemented
interrupts should be masked. Add a bitmap field to mask the non-implemented
interrupts.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-18-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) showed, PLDA PCIe contains an interrupt
controller.
PolarFire implements its own PCIe interrupts, additional to the regular
PCIe interrupts, due to lack of an MSI controller, so the interrupt to
event number mapping is different to the PLDA regular interrupts,
necessitating a custom get_events() implementation.
Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
plda_get_events() adds interrupt register to PLDA event num mapping codes.
All the PLDA interrupts can be seen in new added graph.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-15-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
The INTx and MSI interrupt event num is different across platforms, so
add two event num fields in struct plda_event.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-14-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
As the PLDA DT binding doc (Documentation/devicetree/bindings/pci/
plda,xpressrich3-axi-common.yaml) shows, the PLDA IP contains an interrupt
controller. Microchip PolarFire add some interrupts based on PLDA interrupt
controller.
The Microchip PolarFire PCIe additional interrupts (defined in
drivers/pci/controller/plda/pcie-microchip-host.c):
EVENT_PCIE_L2_EXIT
EVENT_PCIE_HOTRST_EXIT
EVENT_PCIE_DLUP_EXIT
EVENT_SEC_TX_RAM_SEC_ERR
EVENT_SEC_RX_RAM_SEC_ERR
...
Both event_cause[] and mc_event_handler() contain additional interrupt
symbol names; these can not be re-used. Add a new plda_event_handler()
function, which implements PLDA interrupt defalt handler, and add a
request_event_irq() callback function for Microchip PolarFire additional
interrupts.
[kwilczynski, bhelgaas: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-13-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
The number of events is different across platforms. In order to share
interrupt processing code, add a variable that defines the number of
events so that it can be set per-platform instead of hardcoding it.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-12-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Rename mc_* to plda_* for IRQ functions and related IRQ domain ops data
instances.
MSI, INTx interrupt code and IRQ init code can all be re-used.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-11-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Move plda_pcie_setup_window() and plda_pcie_setup_iomems() to
pcie-plda-host.c so they can be shared by all PLDA-based drivers.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-10-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Rename mc_pcie_setup_window() to plda_pcie_setup_window() and
mc_pcie_setup_windows() to plda_pcie_setup_iomems() so they can be shared
by all PLDA-based drivers.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-8-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Move the PLDA generic data structures to a header file so they can be
re-used by all PLDA-based drivers.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-7-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Rename struct mc_msi to plda_msi and move most of struct mc_pcie to a new
struct plda_pcie_rp so they can be shared by all PLDA-based drivers.
The axi_base_addr field remains in struct mc_pcie since it's
Microchip-specific data.
The event interrupt code is still using struct mc_pcie because the event
interrupt code can not be re-used.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-6-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Bridge address base is common PLDA field, add this to struct mc_pcie first.
INTx and MSI interrupt code will be changed to common code, so get the
bridge base address from port->bridge_addr instead of axi_base_addr.
The axi_base_addr is Microchip-specific data.
Link: https://lore.kernel.org/linux-pci/20240328091835.14797-5-minda.chen@starfivetech.com
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
After 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e70 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Relocate ks_pcie_set_dbi_mode() and ks_pcie_clear_dbi_mode() to avoid
forward declaration in a subsequent patch. No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-2-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to hardcode the clock info in the driver as driver can
rely on the devicetree to supply the clocks required for the functioning
of the peripheral.
Thus, remove the static clock info and obtain the platform supplied
clocks. All the clocks supplied are obtained and enabled using the
devm_clk_bulk_get_all_enable() API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240220084046.23786-3-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the dra7xx_pcie_cpu_addr_fixup() function parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-3-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the artpec6_pcie_cpu_addr_fixup() parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-4-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
If IORESOURCE_BUS is not provided in Device Tree it will be fabricated in
of_pci_parse_bus_range(), so NULL pointer dereference should not happen
here.
But that's hard to verify, so check for NULL anyway.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-pci/20240503125705.46055-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
BME which stands for 'Bus Master Enable' is not defined in the PCIe base
spec even though it is commonly referred in many places (vendor docs). To
align with the spec, rename it to its expansion 'Bus Master Enable'.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: squash removal of irrelevant 'Link is enabled']
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
SA8775P SoC supports the new Hyper DMA (HDMA) DMA Engine inside the DWC IP,
so add support for it by passing the mapping format and the number of
read/write channels count.
The PCIe EP controller used on this SoC is of version 1.34.0, so a separate
config struct is introduced for the sake of enabling HDMA conditionally.
It should be noted that for the eDMA support (predecessor of HDMA), there
are no mapping format and channels count specified. That is because eDMA
supports auto detection of both parameters, whereas HDMA doesn't.
[mani: reworded commit message, added kdoc, and minor cleanups]
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-4-f04c5cdde760@linaro.org
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Instead of maintaining a separate capability for glue drivers that cannot
support auto detection of the eDMA mapping format, pass the mapping format
directly from them.
This will simplify the code and also allow adding HDMA support that also
doesn't support auto detection of mapping format.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-3-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In the case of Hyper DMA (HDMA) present in DWC controllers, there is no way
the drivers can auto detect the number of read/write channels as like its
predecessor embedded DMA (eDMA). So the glue drivers making use of HDMA
have to pass the channels count during probe.
To accommodate that, skip the existing auto detection of channels count
procedure for HDMA based platforms. If the channels count passed by the
glue drivers were wrong in any form, then the existing sanity check will
catch it.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-2-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In order to add support for Hyper DMA (HDMA), refactor the existing
dw_pcie_edma_find_chip() API by moving the common code to separate
functions.
No functional change.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20240318-dw-hdma-v5-1-f04c5cdde760@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <frank.li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Add support for SA8775P SoC to the Qualcomm PCIe Endpoint Controller
driver. Adding new compatible string as it has different set of clocks
compared to other SoCs.
Link: https://lore.kernel.org/linux-pci/1714492540-15419-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need for the device drivers to validate the clocks defined in
Devicetree. The validation should be performed by the DT schema and the
drivers should just get all the clocks from DT. Right now the driver
hardcodes the clock info and validates them against DT which is redundant.
So use devm_clk_bulk_get_all() that just gets all the clocks defined in DT
and get rid of all static clocks info from the driver. This simplifies the
driver.
Link: https://lore.kernel.org/linux-pci/20240417-pci-qcom-clk-bulk-v1-1-52ca19b3d6b2@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Return success from endpoint probe before incorrectly dropping the
reference to the BPMP (Vidya Sagar)
* pci/controller/tegra194:
PCI: tegra194: Fix probe path for Endpoint mode
- Configure endpoint BAR to be 64-bit if the PCI_BASE_ADDRESS_MEM_TYPE_64
flag is set instead of depending on the new BAR value itself (Niklas
Cassel)
- Set Subsystem Vendor ID correctly (Rick Wertenbroek)
* pci/controller/rockchip:
PCI: rockchip-ep: Remove wrong mask on subsys_vendor_id
PCI: rockchip-ep: Set a 64-bit BAR if requested
- Move DBI accesses from dw_pcie_ep_init() to dw_pcie_ep_init_complete() so
drivers for endpoints that require Refclk for DBI access, e.g., qcom and
tegra194, can control when this happens (Manivannan Sadhasivam)
- Add endpoint API kernel-doc (Manivannan Sadhasivam)
- Remove .deinit() callback and instead call rcar_gen4_pcie_ep_deinit()
explicitly from rcar-gen4, which was the only user (Manivannan
Sadhasivam)
- Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit() to correspond with
dw_pcie_ep_init() (Manivannan Sadhasivam)
- Add dw_pcie_ep_cleanup() for drivers that need to clean up eDMA resources
when PERST# is asserted, e.g., qcom, tegra194 (Manivannan Sadhasivam)
- Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers() to
better reflect the functionality (Manivannan Sadhasivam)
- Call dw_pcie_ep_init_registers() directly from drivers instead of from
dw_pcie_ep_init() so drivers, e.g., qcom and tegra194, can do it when
Refclk is available (Manivannan Sadhasivam)
- Remove the "core_init_notifier" flag, which previously identified drivers
that required Refclk before DBI access, because it's now unnecessary
(Manivannan Sadhasivam)
* pci/controller/dwc:
PCI: endpoint: Remove "core_init_notifier" flag
PCI: dwc: ep: Call dw_pcie_ep_init_registers() API directly from all glue drivers
PCI: dwc: ep: Rename dw_pcie_ep_init_complete() to dw_pcie_ep_init_registers()
PCI: dwc: ep: Introduce dw_pcie_ep_cleanup() API for drivers supporting PERST#
PCI: dwc: ep: Rename dw_pcie_ep_exit() to dw_pcie_ep_deinit()
PCI: dwc: ep: Remove deinit() callback from struct dw_pcie_ep_ops
PCI: dwc: ep: Add Kernel-doc comments for APIs
PCI: dwc: ep: Fix DBI access failure for drivers requiring refclk from host
Remove wrong mask on subsys_vendor_id. Both the Vendor ID and Subsystem
Vendor ID are u16 variables and are written to a u32 register of the
controller. The Subsystem Vendor ID was always 0 because the u16 value
was masked incorrectly with GENMASK(31,16) resulting in all lower 16
bits being set to 0 prior to the shift.
Remove both masks as they are unnecessary and set the register correctly
i.e., the lower 16-bits are the Vendor ID and the upper 16-bits are the
Subsystem Vendor ID.
This is documented in the RK3399 TRM section 17.6.7.1.17
[kwilczynski: removed unnecesary newline]
Fixes: cf590b0783 ("PCI: rockchip: Add EP driver for Rockchip PCIe controller")
Link: https://lore.kernel.org/linux-pci/20240403144508.489835-1-rick.wertenbroek@gmail.com
Signed-off-by: Rick Wertenbroek <rick.wertenbroek@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Cc: stable@vger.kernel.org
The following warning appears when driver is compiled with W=1.
CC drivers/pci/controller/pcie-mt7621.o
drivers/pci/controller/pcie-mt7621.c: In function ‘mt7621_pcie_probe’:
drivers/pci/controller/pcie-mt7621.c:228:49: error: ‘snprintf’ output may
be truncated before the last format character [-Werror=format-truncation=]
228 | snprintf(name, sizeof(name), "pcie-phy%d", slot);
| ^
drivers/pci/controller/pcie-mt7621.c:228:9: note: ‘snprintf’ output between
10 and 11 bytes into a destination of size 10
228 | snprintf(name, sizeof(name), "pcie-phy%d", slot);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Clean this up increasing destination buffer one byte.
[kwilczynski: commit log]
Closes: https://lore.kernel.org/linux-pci/20240110212302.GA2123146@bhelgaas/T/#t
Link: https://lore.kernel.org/linux-pci/20240111082704.2259450-1-sergio.paracuellos@gmail.com
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Tegra194 PCIe probe path is taking failure path in success case for
Endpoint mode. Return success from the switch case instead of going
into the failure path.
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/linux-pci/20240408093053.3948634-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
"core_init_notifier" flag is set by the glue drivers requiring refclk from
the host to complete the DWC core initialization. Also, those drivers will
send a notification to the EPF drivers once the initialization is fully
completed using the pci_epc_init_notify() API. Only then, the EPF drivers
will start functioning.
For the rest of the drivers generating refclk locally, EPF drivers will
start functioning post binding with them. EPF drivers rely on the
'core_init_notifier' flag to differentiate between the drivers.
Unfortunately, this creates two different flows for the EPF drivers.
So to avoid that, let's get rid of the "core_init_notifier" flag and follow
a single initialization flow for the EPF drivers. This is done by calling
the dw_pcie_ep_init_notify() from all glue drivers after the completion of
dw_pcie_ep_init_registers() API. This will allow all the glue drivers to
send the notification to the EPF drivers once the initialization is fully
completed.
Only difference here is that, the drivers requiring refclk from host will
send the notification once refclk is received, while others will send it
during probe time itself.
But this also requires the EPC core driver to deliver the notification
after EPF driver bind. Because, the glue driver can send the notification
before the EPF drivers bind() and in those cases the EPF drivers will miss
the event. To accommodate this, EPC core is now caching the state of the
EPC initialization in 'init_complete' flag and pci-ep-cfs driver sends the
notification to EPF drivers based on that after each EPF driver bind.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-8-082625472414@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently, dw_pcie_ep_init_registers() API is directly called by the glue
drivers requiring active refclk from host. But for the other drivers, it is
getting called implicitly by dw_pcie_ep_init(). This is due to the fact
that this API initializes DWC EP specific registers and that requires an
active refclk (either from host or generated locally by endpoint itsef).
But, this causes a discrepancy among the glue drivers. So to avoid this
confusion, let's call this API directly from all glue drivers irrespective
of refclk dependency. Only difference here is that the drivers requiring
refclk from host will call this API only after the refclk is received and
other drivers without refclk dependency will call this API right after
dw_pcie_ep_init().
With this change, the check for 'core_init_notifier' flag can now be
dropped from dw_pcie_ep_init() API. This will also allow us to remove the
'core_init_notifier' flag completely in the later commits.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-7-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
The goal of the dw_pcie_ep_init_complete() API is to initialize the DWC
specific registers post registering the controller with the EP framework.
But the naming doesn't reflect its functionality and causes confusion. So,
let's rename it to dw_pcie_ep_init_registers() to make it clear that it
initializes the DWC specific registers.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-6-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
For DWC glue drivers supporting PERST# (currently Qcom and Tegra194), some
of the DWC resources like eDMA should be cleaned up during the PERST#
assert time.
So let's introduce a dw_pcie_ep_cleanup() API that could be called by these
drivers to cleanup the DWC specific resources. Currently, it just removes
eDMA.
Closes: https://lore.kernel.org/linux-pci/ZWYmX8Y%2F7Q9WMxES@x1-carbon
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-5-082625472414@linaro.org
Reported-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
dw_pcie_ep_exit() API is undoing what the dw_pcie_ep_init() API has done
already (at least partly). But the API name dw_pcie_ep_exit() is not quite
reflecting that. So let's rename it to dw_pcie_ep_deinit() to make the
purpose of this API clear. This also aligns with the DWC host driver.
Link: https://patchwork.kernel.org/project/linux-pci/patch/20240327-pci-dbi-rework-v12-4-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
deinit() callback was solely introduced for the pcie-rcar-gen4 driver where
it is used to do platform specific resource deallocation. And this callback
is called right at the end of the dw_pcie_ep_exit() API. So it doesn't
matter whether it is called within or outside of dw_pcie_ep_exit() API.
So let's remove this callback and directly call rcar_gen4_pcie_ep_deinit()
in pcie-rcar-gen4 driver to do resource deallocation after the completion
of dw_pcie_ep_exit() API in rcar_gen4_remove_dw_pcie_ep().
This simplifies the DWC layer.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-3-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
All of the APIs are missing the Kernel-doc comments. Hence, add them.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-2-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
The DWC glue drivers requiring an active reference clock from the PCIe host
for initializing their PCIe EP core, set a flag called 'core_init_notifier'
to let DWC driver know that these drivers need a special attention during
initialization. In these drivers, access to the hw registers (like DBI)
before receiving the active refclk from host will result in access failure
and also could cause a whole system hang.
But the current DWC EP driver doesn't honor the requirements of the drivers
setting 'core_init_notifier' flag and tries to access the DBI registers
during dw_pcie_ep_init(). This causes the system hang for glue drivers such
as Tegra194 and Qcom EP as they depend on refclk from host and have set the
above mentioned flag.
To workaround this issue, users of the affected platforms have to maintain
the dependency with the PCIe host by booting the PCIe EP after host boot.
But this won't provide a good user experience, since PCIe EP is _one_ of
the features of those platforms and it doesn't make sense to delay the
whole platform booting due to PCIe requiring active refclk.
So to fix this issue, let's move all the DBI access from
dw_pcie_ep_init() in the DWC EP driver to the dw_pcie_ep_init_complete()
API. This API will only be called by the drivers setting
'core_init_notifier' flag once refclk is received from host. For the rest
of the drivers that gets the refclk locally, this API will be called
within dw_pcie_ep_init().
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-1-082625472414@linaro.org
Fixes: e966f7390d ("PCI: dwc: Refactor core initialization code for EP mode")
Co-developed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Ever since commit f25b5fae29 ("PCI: endpoint: Setting a BAR size > 4 GB
is invalid if 64-bit flag is not set") it has been impossible to get the
.set_bar() callback with a BAR size > 2 GB (yes, 2GB!), if the BAR was
also not requested to be configured as a 64-bit BAR.
It is however possible that an EPF driver configures a BAR as 64-bit,
even if the requested size is < 4 GB.
Respect the requested BAR configuration, just like how it is already
respected with regards to the prefetchable bit.
Link: https://lore.kernel.org/linux-pci/20240320113157.322695-8-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Ever since commit f25b5fae29 ("PCI: endpoint: Setting a BAR size > 4 GB
is invalid if 64-bit flag is not set") it has been impossible to get the
.set_bar() callback with a BAR size > 2 GB (yes, 2GB!), if the BAR was
also not requested to be configured as a 64-bit BAR.
Thus, forcing setting the 64-bit flag for BARs larger than 2 GB in the
lower level driver is dead code and can be removed.
It is however possible that an EPF driver configures a BAR as 64-bit,
even if the requested size is < 4 GB.
Respect the requested BAR configuration, just like how it is already
respected with regards to the prefetchable bit.
Link: https://lore.kernel.org/linux-pci/20240320113157.322695-7-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----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=AP3I
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate interrupt related code in irq.c (Ilpo Järvinen)
- Reduce kernel size by replacing sysfs resource macros with
functions (Ilpo Järvinen)
- Reduce kernel size by compiling sysfs support only when
CONFIG_SYSFS=y (Lukas Wunner)
- Avoid using Extended Tags on 3ware-9650SE Root Port to work around
an apparent hardware defect (Jörg Wedekind)
Resource management:
- Fix an MMIO mapping leak in pci_iounmap() (Philipp Stanner)
- Move pci_iomap.c and other PCI-specific devres code to drivers/pci
(Philipp Stanner)
- Consolidate PCI devres code in devres.c (Philipp Stanner)
Power management:
- Avoid D3cold on Asus B1400 PCI-NVMe bridge, where firmware doesn't
know how to return correctly to D0, and remove previous quirk that
wasn't as specific (Daniel Drake)
- Allow runtime PM when the driver enables it but doesn't need any
runtime PM callbacks (Raag Jadav)
- Drain runtime-idle callbacks before driver removal to avoid races
between .remove() and .runtime_idle(), which caused intermittent
page faults when the rtsx .runtime_idle() accessed registers that
its .remove() had already unmapped (Rafael J. Wysocki)
Virtualization:
- Avoid Secondary Bus Reset on LSI FW643 so it can be assigned to VMs
with VFIO, e.g., for professional audio software on many Apple
machines, at the cost of leaking state between VMs (Edmund Raile)
Error handling:
- Print all logged TLP Prefixes, not just the first, after AER or DPC
errors (Ilpo Järvinen)
- Quirk the DPC PIO log size for Intel Raptor Lake Root Ports, which
still don't advertise a legal size (Paul Menzel)
- Ignore expected DPC Surprise Down errors on hot removal (Smita
Koralahalli)
- Block runtime suspend while handling AER errors to avoid races that
prevent the device form being resumed from D3hot (Stanislaw
Gruszka)
Peer-to-peer DMA:
- Use atomic XA allocation in RCU read section (Christophe JAILLET)
ASPM:
- Collect bits of ASPM-related code that we need even without
CONFIG_PCIEASPM into aspm.c (David E. Box)
- Save/restore L1 PM Substates config for suspend/resume (David E.
Box)
- Update save_save when ASPM config is changed, so a .slot_reset()
during error recovery restores the changed config, not the
.probe()-time config (Vidya Sagar)
Endpoint framework:
- Refactor and improve pci_epf_alloc_space() API (Niklas Cassel)
- Clean up endpoint BAR descriptions (Niklas Cassel)
- Fix ntb_register_device() name leak in error path (Yang Yingliang)
- Return actual error code for pci_vntb_probe() failure (Yang
Yingliang)
Broadcom STB PCIe controller driver:
- Fix MDIO write polling, which previously never waited for
completion (Jonathan Bell)
Cadence PCIe endpoint driver:
- Clear the ARI "Next Function Number" of last function (Jasko-EXT
Wojciech)
Freescale i.MX6 PCIe controller driver:
- Simplify by replacing switch statements with function pointers for
different hardware variants (Frank Li)
- Simplify by using clk_bulk*() API (Frank Li)
- Remove redundant DT clock and reg/reg-name details (Frank Li)
- Add i.MX95 DT and driver support for both Root Complex and Endpoint
mode (Frank Li)
Microsoft Hyper-V host bridge driver:
- Reduce memory usage by limiting ring buffer size to 16KB instead of
4 pages (Michael Kelley)
Qualcomm PCIe controller driver:
- Add X1E80100 DT and driver support (Abel Vesa)
- Add DT 'required-opps' for SoCs that require a minimum performance
level (Johan Hovold)
- Make DT 'msi-map-mask' optional, depending on how MSI interrupts
are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because the PHY
configuration isn't tuned correctly for L0s (Johan Hovold)
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and
separate files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150,
SM8250, SM8350, SM8450, SM8550 for easier reviewing (Krzysztof
Kozlowski)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add endpoint MHI support for Snapdragon SA8775P SoC (Mrinmay
Sarkar)
Synopsys DesignWare PCIe controller driver:
- Allocate 64-bit MSI address if no 32-bit address is available (Ajay
Agarwal)
- Fix endpoint Resizable BAR to actually advertise the required 1MB
size (Niklas Cassel)
MicroSemi Switchtec management driver:
- Release resources if the .probe() fails (Christophe JAILLET)
Miscellaneous:
- Make pcie_port_bus_type const (Ricardo B. Marliere)"
* tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (77 commits)
PCI/ASPM: Update save_state when configuration changes
PCI/ASPM: Disable L1 before configuring L1 Substates
PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state()
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI: hv: Fix ring buffer size calculation
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: cadence: Clear the ARI Capability Next Function Number of the last function
PCI: dwc: Strengthen the MSI address allocation logic
PCI: brcmstb: Fix broken brcm_pcie_mdio_write() polling
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI/AER: Generalize TLP Header Log reading
PCI/AER: Use explicit register size for PCI_ERR_CAP
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
PCI/AER: Block runtime suspend when handling errors
PCI/ASPM: Move pci_save_ltr_state() to aspm.c
PCI/ASPM: Always build aspm.c
...
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and separate
files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150, SM8250, SM8350,
SM8450, SM8550 for easier reviewing (Krzysztof Kozlowski)
- Allow 'required-opps' DT property for SoCs that require a minimum
performance level for the power domain (Johan Hovold)
- Remove requirement for 'msi-map-mask' DT property since it depends on how
MSIs are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because their PHY
configuration isn't tuned for L0s, which results in many Correctable
Errors (Johan Hovold)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add DT binding and driver support for X1E80100 (Abel Vesa)
* pci/controller/qcom:
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
dt-bindings: PCI: qcom,pcie-sa8775p: Move SA8775p to dedicated schema
dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8180x: Move SC8180X to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8280xp: Move SC8280XP to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8350: Move SM8350 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8150: Move SM8150 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8250: Move SM8250 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8450: Move SM8450 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8550: Move SM8550 to dedicated schema
- Fix ring buffer size at 16KB (not 4 pages), which reduces memory usage by
128KBytes with 64KB pages (Michael Kelley)
* pci/controller/hyperv:
PCI: hv: Fix ring buffer size calculation
- Fall back to allocating 64-bit MSI DMA address if unable to allocate a
32-bit address (Ajay Agarwal)
* pci/controller/dwc:
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: dwc: Strengthen the MSI address allocation logic
- Clear the ARI Capability Next Function Number of the last function
(Jasko-EXT Wojciech)
* pci/controller/cadence:
PCI: cadence: Clear the ARI Capability Next Function Number of the last function
- Fix polling for MDIO write completion, which previously used the wrong
access width so it always indicated "completed" (Jonathan Bell)
* pci/controller/broadcom:
PCI: brcmstb: Fix broken brcm_pcie_mdio_write() polling
For a physical PCI device that is passed through to a Hyper-V guest VM,
current code specifies the VMBus ring buffer size as 4 pages. But this
is an inappropriate dependency, since the amount of ring buffer space
needed is unrelated to PAGE_SIZE. For example, on x86 the ring buffer
size ends up as 16 Kbytes, while on ARM64 with 64 Kbyte pages, the ring
size bloats to 256 Kbytes. The ring buffer for PCI pass-thru devices
is used for only a few messages during device setup and removal, so any
space above a few Kbytes is wasted.
Fix this by declaring the ring buffer size to be a fixed 16 Kbytes.
Furthermore, use the VMBUS_RING_SIZE() macro so that the ring buffer
header is properly accounted for, and so the size is rounded up to a
page boundary, using the page size for which the kernel is built. While
w/64 Kbyte pages this results in a 64 Kbyte ring buffer header plus a
64 Kbyte ring buffer, that's the smallest possible with that page size.
It's still 128 Kbytes better than the current code.
Link: https://lore.kernel.org/linux-pci/20240216202240.251818-1-mhklinux@outlook.com
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Ilpo Jarvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Long Li <longli@microsoft.com>
Cc: <stable@vger.kernel.org> # 5.15.x
The commit message in commit fc9a77040b ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
Next Function Number field in ARI Capability Register for last function
must be zero by default as per the PCIe specification, indicating there
is no next higher number function but that's not happening in our case,
so this patch clears the Next Function Number field for last function
used.
[kwilczynski: white spaces update for one define]
Link: https://lore.kernel.org/linux-pci/20231202085015.3048516-1-s-vadapalli@ti.com
Signed-off-by: Jasko-EXT Wojciech <wojciech.jasko-EXT@continental-corporation.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
There can be platforms that do not use/have 32-bit DMA addresses.
The current implementation of 32-bit IOVA allocation can fail for
such platforms, eventually leading to the probe failure.
Try to allocate a 32-bit msi_data. If this allocation fails,
attempt a 64-bit address allocation. Please note that if the
64-bit MSI address is allocated, then the EPs supporting 32-bit
MSI address only will not work.
Link: https://lore.kernel.org/linux-pci/20240221153840.1789979-1-ajayagarwal@google.com
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Will McVicker <willmcvicker@google.com>
The MDIO_WT_DONE() macro tests bit 31, which is always 0 (== done) as
readw_poll_timeout_atomic() does a 16-bit read. Replace with the readl
variant.
[kwilczynski: commit log]
Fixes: ca5dcc7631 ("PCI: brcmstb: Replace status loops with read_poll_timeout_atomic()")
Link: https://lore.kernel.org/linux-pci/20240217133722.14391-1-wahrenst@gmx.net
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Add the compatible and the driver data for X1E80100 PCIe controller.
There are 5 controller instances found on this platform, out of which
2 are Gen3 with speeds of up to 8.0GT/s, while the other 3 are Gen4 with
speeds of up to 16GT/s.
The version of the controller is 1.38.0 for all instances, but they are
compatible with 1.9.0 config. The max link width is x8 for one
controller, x4 for two of others and x2 for the two left.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240301-x1e80100-pci-v4-2-7ab7e281d647@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c93988221 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
Commit 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting
1.9.0 ops") started enabling ASPM unconditionally when the hardware
claims to support it. This triggers Correctable Errors for some PCIe
devices on machines like the Lenovo ThinkPad X13s when L0s is enabled,
which could indicate an incomplete driver ASPM implementation or that
the hardware does in fact not support L0s.
This has now been confirmed by Qualcomm to be the case for sc8280xp and
its derivate platforms (e.g. sa8540p and sa8295p). Specifically, the PHY
configuration used on these platforms is not correctly tuned for L0s and
there is currently no updated configuration available.
Add a new flag to the driver configuration data and use it to disable
ASPM L0s on sc8280xp, sa8540p and sa8295p for now.
Note that only the 1.9.0 ops enable ASPM currently.
Link: https://lore.kernel.org/r/20240306095651.4551-4-johan+linaro@kernel.org
Fixes: 9f4f3dfad8 ("PCI: qcom: Enable ASPM for platforms supporting 1.9.0 ops")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 6.7
Add iMX95 EP support and add 64bit address support.
The internal bus bridge for PCI support 64bit DMA address in iMX95 hence
call dma_set_mask_and_coherent() to set 64 bit DMA mask.
Link: https://lore.kernel.org/r/20240220161924.3871774-15-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The i.MX EP exhibits variations in epc_features among different EP
configurations. This introduces the addition of epc_features in
imx6_pcie_drvdata to accommodate these differences. It's important to note
that there are no functional changes in this commit; instead, it lays the
groundwork for supporting i.MX95 EP functions.
Link: https://lore.kernel.org/r/20240220161924.3871774-13-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Since the dw_pcie_ep_init() function is already fetching the 'addr_space'
region, no need to do the same in this driver.
Link: https://lore.kernel.org/r/20240220161924.3871774-12-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Instead of using the switch case statement to initialize the PHY handled by
this driver itself, let's introduce a new callback init_phy() and define it
for platforms that require it.
Link: https://lore.kernel.org/r/20240220161924.3871774-7-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add drvdata::mode_off and drvdata::mode_mask to simplify
imx6_pcie_configure_type() logic.
Link: https://lore.kernel.org/r/20240220161924.3871774-6-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add drvdata::ltssm_off and drvdata::ltssm_mask to simplify
imx6_pcie_ltssm_enable(disable)() logic.
Link: https://lore.kernel.org/r/20240220161924.3871774-5-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the reset handling logic in the imx6 PCI driver by adding
IMX6_PCIE_FLAG_HAS_*_RESET bitmask define for drvdata::flags.
The drvdata::flags and bitmask ensure a cleaner and more scalable
switch-case structure for handling reset.
Link: https://lore.kernel.org/r/20240220161924.3871774-4-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Since some i.MX platforms make use of a separate PHY driver, use
IMX6_PCIE_FLAG_HAS_PHYDRV flag to identify them and get the reference to
PHY from DT to simplify the code.
Link: https://lore.kernel.org/r/20240220161924.3871774-3-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Refactor the clock handling logic. Add 'clk_names' define in drvdata.
Use clk_bulk*() API to simplify the code.
Link: https://lore.kernel.org/r/20240220161924.3871774-2-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The definition of a reserved BAR is that EPF drivers should not touch
them.
The definition of only_64bit is that the EPF driver must configure this
BAR as 64-bit. (An EPF driver is not allowed to choose if this BAR should
be configured as 32-bit or 64-bit.)
Thus, it does not make sense to put only_64bit of a BAR that EPF drivers
are not allow to touch.
Drop the only_64bit property from hardware descriptions that are of type
reserved BAR.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240216134524.1142149-3-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The hardware description for BARs is scattered in many different variables
in pci_epc_features. Some of these things are mutually exclusive, so it
can create confusion over which variable that has precedence over another.
Improve the situation by creating a struct pci_epc_bar_desc, and a new
enum pci_epc_bar_type, and convert the endpoint controller drivers to use
this more well defined format.
Additionally, some endpoint controller drivers mark the BAR succeeding a
"64-bit only BAR" as reserved, while some do not. By definition, a 64-bit
BAR uses the succeeding BAR for the upper 32-bits, so an EPF driver cannot
use a BAR succeeding a 64-bit BAR. Ensure that all endpoint controller
drivers are uniform, and actually describe a reserved BAR as reserved.
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Kishon Vijay Abraham I <kishon@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20240216134524.1142149-2-cassel@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
-----BEGIN PGP SIGNATURE-----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=jJks
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Fix an unintentional truncation of DWC MSI-X address to 32 bits and
update similar MSI code to match (Dan Carpenter)
* tag 'pci-v6.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: dwc: Clean up dw_pcie_ep_raise_msi_irq() alignment
PCI: dwc: Fix a 64bit bug in dw_pcie_ep_raise_msix_irq()
I recently changed the alignment code in dw_pcie_ep_raise_msix_irq(). The
code in dw_pcie_ep_raise_msi_irq() is similar, so update it to match, just
for consistency. (No effect on runtime, just a cleanup).
Link: https://lore.kernel.org/r/184097e0-c728-42c7-9e8a-556bd33fb612@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd6 ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
A last minute revert in 6.7-final introduced a potential deadlock when
enabling ASPM during probe of Qualcomm PCIe controllers as reported by
lockdep:
============================================
WARNING: possible recursive locking detected
6.7.0 #40 Not tainted
--------------------------------------------
kworker/u16:5/90 is trying to acquire lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pcie_aspm_pm_state_change+0x58/0xdc
but task is already holding lock:
ffffacfa78ced000 (pci_bus_sem){++++}-{3:3}, at: pci_walk_bus+0x34/0xbc
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(pci_bus_sem);
lock(pci_bus_sem);
*** DEADLOCK ***
Call trace:
print_deadlock_bug+0x25c/0x348
__lock_acquire+0x10a4/0x2064
lock_acquire+0x1e8/0x318
down_read+0x60/0x184
pcie_aspm_pm_state_change+0x58/0xdc
pci_set_full_power_state+0xa8/0x114
pci_set_power_state+0xc4/0x120
qcom_pcie_enable_aspm+0x1c/0x3c [pcie_qcom]
pci_walk_bus+0x64/0xbc
qcom_pcie_host_post_init_2_7_0+0x28/0x34 [pcie_qcom]
The deadlock can easily be reproduced on machines like the Lenovo ThinkPad
X13s by adding a delay to increase the race window during asynchronous
probe where another thread can take a write lock.
Add a new pci_set_power_state_locked() and associated helper functions that
can be called with the PCI bus semaphore held to avoid taking the read lock
twice.
Link: https://lore.kernel.org/r/ZZu0qx2cmn7IwTyQ@hovoldconsulting.com
Link: https://lore.kernel.org/r/20240130100243.11011-1-johan+linaro@kernel.org
Fixes: f93e71aea6 ("Revert "PCI/ASPM: Remove pcie_aspm_pm_state_change()"")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: <stable@vger.kernel.org> # 6.7
Manivannan Sadhasivam
Mrinmay Sarkar
Jeff Johnson
Wei Liu
Yoshihiro Shimoda
Kishon Vijay Abraham I
Christophe JAILLET
Dr. David Alan Gilbert
Vidya Sagar
Jon Hunter
Marek Vasut
Minda Chen
Aleksandr Mishin
Siddharth Vadapalli
Andy Shevchenko
Shradha Todi
Niklas Cassel
Bjorn Helgaas
Rick Wertenbroek
Sergio Paracuellos
Linus Torvalds
Michael Kelley
Jasko-EXT Wojciech
Ajay Agarwal
Jonathan Bell
Abel Vesa
Johan Hovold
Frank Li
Dan Carpenter