Make the default DP port preemphasis configurable via new DT property
"toshiba,pre-emphasis". This is useful in case the DP link properties
are known and starting link training from preemphasis setting of 0 dB
is not useful. The preemphasis can be set separately for both DP lanes
in range 0=0dB, 1=3.5dB, 2=6dB .
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708150130.54484-2-marex@denx.de
This reverts commit 01338bb82f.
With clock improvements in place, this seems to be no longer
necessary. Set the CLRSIPO to default setting recommended by
manufacturer.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-5-marex@denx.de
The only information in the datasheet regarding this divider is a note
in SYS_PLLPARAM register documentation which states that when LSCLK is
270 MHz, LSCLK_DIV should be 1. What should LSCLK_DIV be set to when
LSCLK is 162 MHz (for DP 1.62G mode) is unclear, but empirical test
confirms using LSCLK_DIV 1 has no adverse effects either. In the worst
case, the internal TC358767 clock would run faster.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-4-marex@denx.de
This line_pixel_subtract is no longer needed now that the bridge can
request and obtain specific pixel clock on input to the bridge, with
clock frequency that matches the Pixel PLL frequency.
The line_pixel_subtract is now always 0, so drop it entirely.
The line_pixel_subtract was not reliable as it never worked when the
Pixel PLL and input clock were off just so that the required amount
of pixels to subtract would not be whole integer.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-3-marex@denx.de
Use tc_pxl_pll_calc() to find out the exact clock frequency generated by the
Pixel PLL. Use the Pixel PLL frequency as adjusted_mode clock frequency and
pass it down the display pipeline to obtain exactly this frequency on input
into this bridge.
The precise input frequency that matches the Pixel PLL frequency is
important for this bridge, as if the frequencies do not match, the
bridge does suffer VFIFO overruns or underruns.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-2-marex@denx.de
Split tc_pxl_pll_en() into tc_pxl_pll_calc() which does only Pixel PLL
parameter calculation and tc_pxl_pll_en() which calls tc_pxl_pll_calc()
and then configures the Pixel PLL register.
This is a preparatory patch for further rework, where tc_pxl_pll_calc()
will also be used to find out the exact clock frequency generated by the
Pixel PLL. This frequency will be used as adjusted_mode clock frequency
and passed down the display pipeline to obtain exactly this frequency
on input into this bridge.
The precise input frequency that matches the Pixel PLL frequency is
important for this bridge, as if the frequencies do not match, the
bridge does suffer VFIFO overruns or underruns.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625120334.145320-1-marex@denx.de
With new connector model, tc358767 will not create the connector, when
DRM_BRIDGE_ATTACH_NO_CONNECTOR is set and display-controller driver will
rely on format negotiation to setup the encoder format.
Add the missing bus format negotiation hooks in the
drm_bridge_funcs to complete DRM_BRIDGE_ATTACH_NO_CONNECTOR support.
Output format, for DPI/DSI to DP, is selected to
MEDIA_BUS_FMT_RGB888_1X24 as default, keeping in mind what the older
model used to support.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Closes: https://lore.kernel.org/all/24282420-b4dd-45b3-bb1c-fc37fe4a8205@siemens.com/
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231108-tc358767-v2-1-25c5f70a2159@ideasonboard.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Make sure the connector is fully initialized before signalling any
HPD events via drm_kms_helper_hotplug_event(), otherwise this may
lead to NULL pointer dereference.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240531203333.277476-1-marex@denx.de
Fix comment copy-paste error in tc_edp_mode_valid(), this function
is validating DP/eDP clock, not DPI clock frequency. Update the
comment to match. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240531203213.277421-1-marex@denx.de
TC9595 datasheet Video Path0 Control (VPCTRL0) Register bit FRMSYNC description
says "This bit should be disabled only in video mode transmission where Host
transmits video timing together with video data and where pixel clock source
is from DSI clock." . This driver always sources pixel clock from external xtal,
therefore the FRMSYNC bit must always be enabled, enable it.
This fixes an actual issue with DSI-to-DPI mode, where the display would
randomly show subtle pixel flickering, or wobble, or shimmering. This is
visible on solid gray color, but the degree of the shimmering differs
between boots, which makes it hard to debug.
There is a caveat to the FRMSYNC and this bridge pixel PLL, which can only
generate pixel clock with limited accuracy, it may therefore be necessary
to reduce the HFP to fit into line length of input pixel data, to avoid any
possible overflows, which make the output video look striped horizontally.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240513021607.129111-1-marex@denx.de
According to new configuration spreadsheet from Toshiba for TC9595,
the Pixel PLL input clock have to be in range 6..40 MHz. The sheet
calculates those PLL input clock as reference clock divided by both
pre-dividers. Add the extra limit.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118220243.203655-1-marex@denx.de
The maple tree register cache is based on a much more modern data structure
than the rbtree cache and makes optimisation choices which are probably
more appropriate for modern systems than those made by the rbtree cache.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231001-drm-tc358767-maple-v1-1-f759fcc4bd98@kernel.org
The documentation is not clear about how this delay works.
Empirical tests have shown that with a VSDELAY of 0, the first
scanline is not properly formatted in the output stream when
DSI->DP mode is used. The calculation spreadsheets from Toshiba
seem to always make this value equal to the HFP + 10 for DSI->DP
use-case. For DSI->DPI this value should be > 2 and for DPI->DP
it seems to always be 0x64.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Marek Vasut <marex@denx.de> # TC9595
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721165328.3968759-2-l.stach@pengutronix.de
The PLL often fails to lock with this delay. The new value was
determined by trial and error increasing the delay bit by bit
until the error did not occurr anymore even after several tries.
Then double that value was taken as the minimum delay to be safe.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de> # TC9595
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230721165328.3968759-1-l.stach@pengutronix.de
The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the need of a dedicated function used
with devm_add_action_or_reset().
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/208a15ce4e01973daf039ad7bc0f9241f650b3af.1672415956.git.christophe.jaillet@wanadoo.fr
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526090709.1517297-1-u.kleine-koenig@pengutronix.de
This map was created from register map from datasheet (section 5.1.2).
Unused registers are stated by address, so they show up in debugfs as well.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230516071949.375264-1-alexander.stein@ew.tq-group.com
The TC358767/TC358867/TC9595 are capable of DSI burst mode, which
is more energy efficient than the non-burst modes. Make use of it.
The TC358767/TC358867/TC9595 are capable of DSI non-continuous clock,
since it sources the internal PLL clock from external clock source.
The DSI non-continuous clock further reduces power utilization.
The TC358767/TC358867/TC9595 may use DSI LPM for command transmissions,
make sure this is configured correctly in the DSI mode flags.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221016003632.406468-1-marex@denx.de
The current CLRSIPO count is still marginal and does not work with high
DSI clock rates in burst mode. Increase it further to allow the DSI link
to work at up to 1Gbps lane speed. This returns the counts to defaults
as provided by datasheet.
Fixes: ea6490b022 ("drm/bridge: tc358767: increase CLRSIPO count")
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221016003556.406441-1-marex@denx.de
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20221118224540.619276-33-uwe@kleine-koenig.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU: simplified VBIF configuration
- cleanup CTL interfaces
- DSI: removed unused msm_display_dsc_config struct
- switch regulator calls to new API
- switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduces lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- Improve error and edge conditions handling
- Convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- Add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEEKbZHaGwW9KfbeusDHTzWXnEhr4FAmM894sACgkQDHTzWXnE
hr7EYw//WdVe69TNauCAQiOYdmPp1twmr2o5gDOFLoo4IZw5v+qK0HL/nTrDkBq6
xIu1GLTScOh0AItW1rhFmrtKhO/u/QPQ15P6cO7x8AzlUIhVOYqM79+OA0X6zIV8
IZjpc6EEWPSKJTCRud9HdzsV06DIa+QlwShLCaOFxRiGSuUqsxzacIHUqnFekRnV
PBG7RzcmdWwe6Gy/7T2wegsFjw1mh4S4FypEGs53emru3PGvcau5dwXcE5Jro7Br
k4BFFknuXahVJ2ynVfIFn3QUQRMLgAKRWflqxo7McLeKVQEt4gfB6+PaMwGpSiRQ
iC9QPy69TWEx6X015q2DvvlQDewnCbPOlzyoj9O991QDGLPIim8srPblr8DPeeOz
Y7IW1PRVnPdKReMJvTyrIVED/XT9fUoR7N+F9sfPnEee5HsvjXNGumEHbOE8avFf
rB6CFdby+Ecd9cSeINXowFy4ss0d5zCHMiKEVyQWTZOJysp29vLyKezNqU5m37FK
LAQHtsRdn1+V3o22H5y1PJyqssbOMImMV1ffqW/urRLLefPVHIKCKI8Ycgh0qxqc
B+gebHMgF8j6RR0DHAcQby+PIVi/Pn36TAMI3lPsVjFWGS5s5EQwpKlMNj46H0Cr
yE2Vr4w29+Nsv0b4Uz16AZ0mHcauqx4bvWMyT0frJfNcE86x8MI=
=u/MJ
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Lots of stuff all over, some new AMD IP support and gang submit
support. i915 has further DG2 and Meteorlake pieces, and a bunch of
i915 display refactoring. msm has a shrinker rework. There are also a
bunch of conversions to use kunit.
This has two external pieces, some MEI changes needed for future Intel
discrete GPUs. These should be acked by Greg. There is also a cross
maintainer shared tree with some backlight rework from Hans in here.
Core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU:
simplified VBIF configuration
cleanup CTL interfaces
- DSI:
removed unused msm_display_dsc_config struct
switch regulator calls to new API
switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduce lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- improve error and edge conditions handling
- convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support"
* tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm: (1374 commits)
drm/amdkfd: Fix UBSAN shift-out-of-bounds warning
drm/amdkfd: Track unified memory when switching xnack mode
drm/amdgpu: Enable sram on vcn_4_0_2
drm/amdgpu: Enable VCN DPG for GC11_0_1
drm/msm: Fix build break with recent mm tree
drm/panel: simple: Use dev_err_probe() to simplify code
drm/panel: panel-edp: Use dev_err_probe() to simplify code
drm/panel: simple: Add Multi-Inno Technology MI0800FT-9
dt-bindings: display: simple: Add Multi-Inno Technology MI0800FT-9 panel
drm/amdgpu: correct the memcpy size for ip discovery firmware
drm/amdgpu: Skip put_reset_domain if it doesn't exist
drm/amdgpu: remove switch from amdgpu_gmc_noretry_set
drm/amdgpu: Fix mc_umc_status used uninitialized warning
drm/amd/display: Prevent OTG shutdown during PSR SU
drm/amdgpu: add page retirement handling for CPU RAS
drm/amdgpu: use RAS error address convert api in mca notifier
drm/amdgpu: support to convert dedicated umc mca address
drm/amdgpu: export umc error address convert interface
drm/amdgpu: fix sdma v4 init microcode error
drm/amd/display: fix array-bounds error in dc_stream_remove_writeback()
...
Currently the driver only handles panel directly connected to the DPI output.
Handle the case where a bridge is connected past DPI output of this bridge.
This could be e.g. DPI to LVDS encoder chip.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220724224317.288727-1-marex@denx.de
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Disable the main link PHYs and put them into reset when the main link
is disabled. When the PHYs stay enabled while the rest of the DP link
circuits are disabled there is some noise on the data lanes, which some
displays try to lock onto, waking them up from their low power state.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706132812.2171250-3-l.stach@pengutronix.de
The current CLRSIPO count is marginal and does not work with high
DSI clock rates. Increase it a bit to allow the DSI link to work at
up to 1Gbps lane speed.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706132812.2171250-2-l.stach@pengutronix.de
There is no need to enforce a specific sync signal polarity on the
DPI interface, as we can simply tell the TC358767 which polarities
it should expect on the input interface.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220706132812.2171250-1-l.stach@pengutronix.de
In tc_probe_bridge_endpoint(), we should call of_node_put() when
breaking out of the for_each_endpoint_of_node() which will automatically
increase and decrease the refcount.
Fixes: 71f7d9c031 ("drm/bridge: tc358767: Detect bridge mode from connected endpoints in DT")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220719065447.1080817-2-windhl@126.com
drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.
Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.
v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com
The DSI lane count can be accessed via the dsi device pointer,
make use of that. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220624181902.151959-1-marex@denx.de
Convert driver to use this new helper to standardize
OF "data-lanes" parsing.
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
To: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220524010522.528569-6-marex@denx.de
The Refclk may be supplied by SoC clock output instead of crystal
oscillator, make sure the clock are enabled before any other action
is performed with the bridge chip, otherwise it may either fail to
operate at all, or miss reset GPIO toggle.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 7caff0fc42 ("drm/bridge: tc358767: Add DPI to eDP bridge driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520121543.11550-1-marex@denx.de
The DSI-to-e(DP) mode is now supported, update the driver comment
to reflect this. No functional change.
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 3080c21a04 ("drm/bridge: tc358767: Add DSI-to-(e)DP mode support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519095137.11896-2-marex@denx.de
Implement DSI-to-e(DP) mode, which is a mix of currently supported
DSI-to-DPI and DPI-to-(e)DP modes. The input side is configured as
either DSI or DPI, the DP AUX channel is registered for both input
side options, and the DSI host is attached for both DPI and (e)DP
output side options.
One notable detail is that the DSI-to-(e)DP mode requires the Pixel
PLL to be always enabled, which is not needed for DPI-to-(e)DP mode
which gets the matching clock direct from DPI Pixel Clock instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429205644.245480-2-marex@denx.de
Factor out register programming to configure the chip video RX side for
reception of video data from DSI or DPI. This is particularly useful in
the (e)DP output mode, where the video data can be received from either
DPI or DSI. While only the former is supported in (e)DP output mode so
far, this patch is added in preparation for addition of the later.
There is a change in the order or register programming in case of the
DSI-to-DPI mode. The DSI RX side is now programmed and enabled all in
one place after the output mode has been configured. Before this change,
the DSI RX has been programmed before the output mode has been set and
only enabled afterward. The order makes no difference however, since the
DSI RX is only enabled at the end either way.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429205644.245480-1-marex@denx.de
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. Make sure the driver treats this as
a valid mode of operation instead of reporting invalid mode.
Fixes: 71f7d9c031 ("drm/bridge: tc358767: Detect bridge mode from connected endpoints in DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429204625.241591-1-marex@denx.de
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. The drm_of_find_panel_or_bridge()
call in tc_probe_edp_bridge_endpoint() returns -ENODEV in case port@2
is not present in DT and this specific return value is incorrectly
propagated outside of tc_probe_edp_bridge_endpoint() function. All
other error values must be propagated and are propagated correctly.
Return 0 in case the port@2 is missing instead, that reinstates the
original behavior before the commit this patch fixes.
Fixes: 8478095a8c ("drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated function")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428213132.447890-1-marex@denx.de
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Add support for the
DSI-to-DPI mode.
This requires skipping most of the (e)DP initialization code, which is
currently a large part of this driver, hence it is better to have far
simpler separate tc_dpi_bridge_funcs and their implementation.
The configuration of DPI output is also much simpler. The configuration
of the DSI input is rather similar to the other TC bridge chips.
The Pixel PLL in DPI output mode does not have the 65..150 MHz limitation
imposed on the (e)DP output mode, so this limitation is skipped to permit
operating panels with far slower pixel clock, even below 9 MHz. This mode
of operation of the PLL is valid and tested.
The detection of bridge mode is now added into tc_probe_bridge_mode(),
where in case a DPI panel is found on port@1 endpoint@1, the mode is
assumed to be DSI-to-DPI. If (e)DP is detected on port@2, the mode is
assumed to be DPI-to-(e)DP.
The DSI-to-(e)DP mode is not supported due to lack of proper hardware,
but this would be some sort of mix between the two aforementioned modes.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-12-marex@denx.de
Marek Vasut
Aradhya Bhatia
Jani Nikula
Alexander Stein
Tomi Valkeinen
Mark Brown
David Jander
Christophe JAILLET
Uwe Kleine-König
Linus Torvalds
Lucas Stach
Liang He
Ville Syrjälä
Thomas Zimmermann