Due to some changes and rebasing between different patches
this fell through the cracks; we need to set sta.mlo if the
connection is using MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It might seem a bit pointless to do a multi-link operation
connection with just a single link, but this is already a
big change, so for now, limit MLO connections to a single
link.
Extending that to multiple links will require
* work on parsing the multi-link element with STA profile
properly, including element fragmentation;
* checking the per-link status in the multi-link element
* implementing logic to have active/inactive links to let
drivers decide which links should be active;
* implementing multicast RX deduplication;
* and likely more.
For now this is still useful since it lets us do multi-link
connections for the purposes of testing APIs and the higher
layers such as wpa_supplicant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we create a station with a non-default link, then
we should have a link address, and we definitely need
to insert it into the link hash table on insertion.
Split the API into with and without link creation and
if it has a link, insert the link into the link hash
table on sta_info_insert().
Fixes: ba6ddab94f ("wifi: mac80211: maintain link-sta hash table")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP/mesh where the stations are added by userspace, we
limit the number of A-MSDU subframes according to the
extended capabilities.
Refactor the code and extend that also to client-side.
Fixes: 506bcfa8ab ("mac80211: limit the A-MSDU Tx based on peer's capabilities")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split out much of the code in ieee80211_set_associated()
into a new ieee80211_link_set_associated() which can be
called per link later for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If NEED_DTIM_BEFORE_ASSOC isn't set, then we don't need
to enter an RCU critical section and look up the beacon
elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Factor out the code to set up the assoc link into a
new function ieee80211_setup_assoc_link().
While at it, also modify the 'override' handling to
just take into account whether or not the conn_flags
were changed, which is what we need to setup again
the channel later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to pass the address, we can look at the auth_data
inside the function rather than outside.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the per-link setup out of ieee80211_assoc_success()
into a new function ieee80211_assoc_config_link().
It looks useless for now to parse the elements again inside
ieee80211_assoc_config_link(), but that will be done with
the link ID in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor ieee80211_prep_channel() to make the link argument
optional and add a conn_flags pointer argument instead, so
that we can later use this for links that don't exist yet
to build the right information for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO, we will need to build these elements per link, so
factor out the code that does this, returning the capability,
to simplify building the multi-link element in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With MLO, when we'll disconnect from an AP MLD, we'll just
destroy all the links. Therefore, the only thing we (may)
need to reset is the deflink data, so switch back to that
and adjust the comments accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO we'll need to read flags not directly from the link as
it may not even exist yet if we're just setting up flags for
a secondary link before sending the association request, so
pass the incoming conn_flags separately. Also, while at it,
pass the sdata/link separately as for non-tracking now the
link may be NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need ieee80211_prep_channel() in other code for MLO
later, so move the code up - unchanged for now - to avoid
forward declarations in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the code here since we need to have it also for each
link station after association in MLO later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flag here is currently per interface, but the way we
set and clear it means it should be per link, so change
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clean up the code building the supported channels element
a little bit by using a local variable instead of the long
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to consider the (maximum) size of the EHT element
we'll add for the association request, otherwise we may run
out of space.
Fixes: 820acc810f ("mac80211: Add EHT capabilities to association/probe request")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The functions currently take a link and check data
from it, but this needs to change for MLO. Simplify
the prototypes by passing only the needed arguments.
Remove the regulatory checks, the warnings shouldn't
trigger, and haven't as far as I know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rework the sorting of custom elements into the association
request by moving the elements before HT/VHT/HE to each
their own function. While at it, fix the placement of the
ones that should be between VHT and HE.
This doesn't fix the placement of elements that should be
between HE and EHT yet, a similar change might be needed
in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's some awkward code that really only exists
because we want to optimize the allocation size,
but that's not really all that necessary.
Refactor the code that adds rates to the association
request frame to have a separate function, removing
the goto.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here, ext_capa is checked and can only be non-NULL if
assoc_data->ie_len was set before, so the check here
is redundant.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When parsing a frame containing a multi-BSSID element, we
need to know both the transmitted and non-transmitted BSSID
so we can parse it correctly.
Unfortunately, in quite a number of cases, we got this wrong
and were passing the wrong BSSID or useless information:
* the mgmt->bssid from a frame is only the transmitted
BSSID if the frame is a beacon
* passing just one of the parameters as non-NULL isn't
useful and ignored
In those case where we need to parse for a specific BSS we
always have a BSS structure pointer, representing the BSS
we need, whether transmitted or not. Thus, pass that pointer
to the parsing function instead of the two BSSIDs.
Also fix two bugs:
* we need to re-parse all the elements for the other BSS
when iterating the non-transmitted BSSes in scan
* we need to parse for the correct BSS when setting up
the channel data in client code
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're already passing the elems pointer, and have parsed
them from the same frame with exactly the same parameters,
so don't need to do that again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the cfg80211_rx_assoc_resp() to cover multiple
BSSes, the AP MLD address and local link addresses
for MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO we'll need a lot more arguments, including all the
BSS pointers and link addresses, so move the data to a struct
to be able to extend it more easily later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We only report the BSSID to userspace, so change the
argument from BSS struct pointer to AP address, which
we'll use to carry either the BSSID or AP MLD address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few cases where we send an event to cfg80211
manually, but ieee80211_destroy_assoc_data() also handles
the case of abandoning; some cases don't need an event
and success is handled yet differently.
Unify this by providing a single status argument to the
ieee80211_destroy_assoc_data() function and then handling
all the different cases of events (or no events) there.
This will help simplify the code when MLO support is
added.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MLO, we need the ability to report back multiple BSS
structures to release, as well as the AP MLD address (if
attempting to make an MLO connection).
Unify cfg80211_assoc_timeout() and cfg80211_abandon_assoc()
into a new cfg80211_assoc_failure() that gets a structure
parameter with the necessary data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The race described by the comment in mac80211 hasn't existed
since the locking rework to use the same lock and for MLO we
need to pass the AP MLD address, so just pass the BSSID or
AP MLD address instead of the BSS struct pointer, and adjust
all the code accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For station capabilities, e.g. TWT, we need to use the correct
link station instead of deflink. Switch the code to do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The argument is unused except for NULL checking, but we already
do that anyway, so it's not needed. Remove the argument.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This requires a few more changes.
While at it, also add a warning to ieee80211_get_sband()
to avoid it being used when there are multiple links.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we decide to stop tracking QoS/WMM parameters, then
this should be a per-link decision. Move the flag to
the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do the first adjustments in the client-side code to pass
the link pointer (instead of sdata) to most places etc.
This is just preparation, so the real MLO patches become
smaller.
Note that this isn't complete, notably there are still
quite a few references to sta->deflink and sta->sta.deflink.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the IEEE80211_STA_RESET_SIGNAL_AVE flag and use
a bool instead, but invert the polarity (now calling it
tracking_signal_avg) so we don't have to initialize it,
and put that into the link instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To prepare a bit more for MLO in the client code,
track the AP's address (for now only the BSSID, but
will track the AP MLD's address later) separately
from the per-link BSSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, expect the driver fully handles powersave handling,
including tracking whether or not a beacon was received,
the DTIM period, etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In station/client mode, the link data needs a bit more
initialization and destruction than just zero-init and
kfree() respectively, implement that.
This required some shuffling of the link data handling
in general, as we should set it up in setup and do the
teardown in teardown, otherwise we're asymmetric in
case of interface type changes.
Also stop using kfree_rcu(), we cannot guarantee that
nothing is scheduling things that live within the link
(e.g. the u.mgd.request_smps_work) until we're sure it
cannot be referenced anymore, therefore synchronize
instead. This isn't very efficient, but we can always
optimize it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Separate out the connection downgrade flags from the ifmgd->flags
and put them into the link information instead. While at it, make
them a separate sparse type so we don't get confused about where
they belong and have static checking on correct handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the mac80211 implementation with P802.11be_D1.5.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places that check ps_sdata and/or the dynamic
PS timeout, but they're erroneous in case SUPPORTS_DYNAMIC_PS
is set by the driver.
Skip the entire recalculation in this case so we cannot get
into those paths elsewhere, and so we simplify this for the
purpose of implementing MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS needs 4addr packets to trigger AP for wlan0.sta creation.
However, the 4addr null frame is sent at a high rate so that
sometimes the AP can't receive it. Switch to using min rate.
Signed-off-by: Lian Chen <lian.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220714091636.59107-1-lian.chen@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to access these in a race-free way under
traffic while adding/removing them, so RCU-ify the pointers.
This requires passing a link_sta to a lot of functions so
we don't have to do the RCU handling everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the necessary infrastructure, including a new driver
method, to add/remove links to/from a station. To do this,
refactor the link alloc/free a bit, splitting that so we
can do it without linking them, to handle failures better.
Note that a station entry must be created representing an
MLD or a non-MLD STA, it cannot change between the two.
When representing an MLD, the 'deflink' is used for the
first link, which might be removed later, in which case
the memory isn't reused.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start reorganizing interface related data structures toward
MLD. The most complex part here is for the keys, since we
have to split the various kinds of GTKs off to the link but
still need to use (for WEP) the other keys as a fallback
even for multicast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only driver using this was iwlwifi, where we just removed
the support because it was never really used. Remove the code
from mac80211 as well.
Change-Id: I1667417a5932315ee9d81f5c233c56a354923f09
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Second set of patches for v5.19 and most likely the last one. rtw89
got support for 8852ce devices and mt76 now supports Wireless Ethernet
Dispatch.
Major changes:
cfg80211/mac80211
* support disabling EHT mode
rtw89
* add support for Realtek 8852ce devices
mt76
* Wireless Ethernet Dispatch support for flow offload
* non-standard VHT MCS10-11 support
* mt7921 AP mode support
* mt7921 ipv6 NS offload support
ath11k
* enable keepalive during WoWLAN suspend
* implement remain-on-channel support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmKGYt4RHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuK2gf/ZswLtwE2CIwrEhz/Q0MDtxUvw8ulRhKl
d+1PC+bCd/VArMESjpu7le+WNAZ1OPBWdh1pgkDm8QpCQZYe7/hRED82DB/Jw3Cl
KmOx2nr6Xb4uEN+yjqZrSXzA+Hrysy24bCQRG2CJKjdToe/fwTuRiz8WIcPKtxio
b/d/Kz0LpSoHTlU1PzqIsXulN8QUKJA4kRw70rJHAlMJVYiTBuAD+AmXfbhHD8uX
t2CJDH2fykDd1CAWFQwcmI++2tS+xclYL81vDg3aEinQJ9aNcDz06qSE5qr2H+K5
lUYy42yc+ONkIIh8LlxrLgZie7oSmkrb7aA0Zc+F0SWp/B6ZO/k8FA==
=aILH
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v5.19
Second set of patches for v5.19 and most likely the last one. rtw89
got support for 8852ce devices and mt76 now supports Wireless Ethernet
Dispatch.
Major changes:
cfg80211/mac80211
- support disabling EHT mode
rtw89
- add support for Realtek 8852ce devices
mt76
- Wireless Ethernet Dispatch support for flow offload
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 ipv6 NS offload support
ath11k
- enable keepalive during WoWLAN suspend
- implement remain-on-channel support
* tag 'wireless-next-2022-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (135 commits)
iwlwifi: mei: fix potential NULL-ptr deref
iwlwifi: mei: clear the sap data header before sending
iwlwifi: mvm: remove vif_count
iwlwifi: mvm: always tell the firmware to accept MCAST frames in BSS
iwlwifi: mvm: add OTP info in case of init failure
iwlwifi: mvm: fix assert 1F04 upon reconfig
iwlwifi: fw: init SAR GEO table only if data is present
iwlwifi: mvm: clean up authorized condition
iwlwifi: mvm: use NULL instead of ERR_PTR when parsing wowlan status
iwlwifi: pcie: simplify MSI-X cause mapping
rtw89: pci: only mask out INT indicator register for disable interrupt v1
rtw89: convert rtw89_band to nl80211_band precisely
rtw89: 8852c: update txpwr tables to HALRF_027_00_052
rtw89: cfo: check mac_id to avoid out-of-bounds
rtw89: 8852c: set TX antenna path
rtw89: add ieee80211::sta_rc_update ops
wireless: Fix Makefile to be in alphabetical order
mac80211: refactor freeing the next_beacon
cfg80211: fix kernel-doc for cfg80211_beacon_data
mac80211: minstrel_ht: support ieee80211_rate_status
...
====================
Link: https://lore.kernel.org/r/20220519153334.8D051C385AA@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We currently track whether we're associated and which the
BSS is in the same variable (ifmgd->associated), but for
MLD we'll need to move the BSS pointer to be per link,
while the question whether we're associated or not is for
the whole interface.
Add ifmgd->assoc_bss that stores the pointer and change
ifmgd->associated to be just a bool, so the question of
whether we're associated can continue working after MLD
rework, without requiring changes, while the BSS pointer
will have to be changed/used checked per link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need to copy this locally, we now only use the
variable to print before doing other things.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We never use the bssid argument to ieee80211_sta_connection_lost()
so we might as well just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to look it up from the ifmgd->associated
BSS configuration, we already maintain a local copy since
commit b0140fda62 ("mac80211: mlme: save ssid info to
ieee80211_bss_conf while assoc").
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we always track the BSSID there when we get associated,
these are equivalent, but ifmgd->bssid saves a dereference and
thus makes the code a bit smaller, and more readable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is tightly coupled to the sdata->u.mgd data
structure, so there's no reason for it to be in utils.
Move it to mlme.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently MBSSID parameters in struct ieee80211_bss_conf
are not reset upon connection. This could be problematic
with some drivers in a scenario where the device first
connects to a non-transmit BSS and then connects to a
transmit BSS of a Multi BSS AP. The MBSSID parameters
which are set after connecting to a non-transmit BSS will
not be reset and the same parameters will be passed on to
the driver during the subsequent connection to a transmit
BSS of a Multi BSS AP.
For example, firmware running on the ath11k device uses the
Multi BSS data for tracking the beacon of a non-transmit BSS
and reports the driver when there is a beacon miss. If we do
not reset the MBSSID parameters during the subsequent
connection to a transmit BSS, then the driver would have
wrong MBSSID data and FW would be looking for an incorrect
BSSID in the MBSSID beacon of a Multi BSS AP and reports
beacon loss leading to an unstable connection.
Reset the MBSSID parameters upon every connection to solve this
problem.
Fixes: 78ac51f815 ("mac80211: support multi-bssid")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Link: https://lore.kernel.org/r/20220428052744.27040-1-quic_mpubbise@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
-----BEGIN PGP SIGNATURE-----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=ccps
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
brcmfmac
* add BCM43454/6 support
rtw89
* add support for 160 MHz channels and 6 GHz band
* hardware scan support
iwlwifi
* support UHB TAS enablement via BIOS
* remove a bunch of W=1 warnings
* add support for channel switch offload
* support 32 Rx AMPDU sessions in newer devices
* add support for a couple of new devices
* add support for band disablement via BIOS
mt76
* mt7915 thermal management improvements
* SAR support for more mt76 drivers
* mt7986 wmac support on mt7915
ath11k
* debugfs interface to configure firmware debug log level
* debugfs interface to test Target Wake Time (TWT)
* provide 802.11ax High Efficiency (HE) data via radiotap
ath9k
* use hw_random API instead of directly dumping into random.c
wcn36xx
* fix wcn3660 to work on 5 GHz band
ath6kl
* add device ID for WLU5150-D81
cfg80211/mac80211
* initial EHT (from 802.11be) support
(EHT rates, 320 MHz, larger block-ack)
* support disconnect on HW restart
* tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits)
mac80211: Add support to trigger sta disconnect on hardware restart
mac80211: fix potential double free on mesh join
mac80211: correct legacy rates check in ieee80211_calc_rx_airtime
nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation
mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible
mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
rtw89: 8852c: process logic efuse map
rtw89: 8852c: process efuse of phycap
rtw89: support DAV efuse reading operation
rtw89: 8852c: add chip::dle_mem
rtw89: add page_regs to handle v1 chips
rtw89: add chip_info::{h2c,c2h}_reg to support more chips
rtw89: add hci_func_en_addr to support variant generation
rtw89: add power_{on/off}_func
rtw89: read chip version depends on chip ID
rtw89: pci: use a struct to describe all registers address related to DMA channel
rtw89: pci: add V1 of PCI channel address
rtw89: pci: add struct rtw89_pci_info
rtw89: 8852c: add 8852c empty files
MAINTAINERS: add devicetree bindings entry for mt76
...
====================
Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently in case of target hardware restart, we just reconfig and
re-enable the security keys and enable the network queues to start
data traffic back from where it was interrupted.
Many ath10k wifi chipsets have sequence numbers for the data
packets assigned by firmware and the mac sequence number will
restart from zero after target hardware restart leading to mismatch
in the sequence number expected by the remote peer vs the sequence
number of the frame sent by the target firmware.
This mismatch in sequence number will cause out-of-order packets
on the remote peer and all the frames sent by the device are dropped
until we reach the sequence number which was sent before we restarted
the target hardware
In order to fix this, we trigger a sta disconnect, in case of target
hw restart. After this there will be a fresh connection and thereby
avoiding the dropping of frames by remote peer.
The right fix would be to pull the entire data path into the host
which is not feasible or would need lots of complex changes and
will still be inefficient.
Tested on ath10k using WCN3990, QCA6174
Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org>
Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we get anti-clogging token required (added by the commit
mentioned below), or the other status codes added by the later
commit 4e56cde15f ("mac80211: Handle special status codes in
SAE commit") we currently just pretend (towards the internal
state machine of authentication) that we didn't receive anything.
This has the undesirable consequence of retransmitting the prior
frame, which is not expected, because the timer is still armed.
If we just disarm the timer at that point, it would result in
the undesirable side effect of being in this state indefinitely
if userspace crashes, or so.
So to fix this, reset the timer and set a new auth_data->waiting
in order to have no more retransmissions, but to have the data
destroyed when the timer actually fires, which will only happen
if userspace didn't continue (i.e. crashed or abandoned it.)
Fixes: a4055e74a2 ("mac80211: Don't destroy auth data in case of anti-clogging")
Reported-by: Jouni Malinen <j@w1.fi>
Link: https://lore.kernel.org/r/20220224103932.75964e1d7932.Ia487f91556f29daae734bf61f8181404642e1eec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We validate that AP has mandatory rates set in HE capabilities.
Also we make sure AP is consistent with itself on rates set in HE basic
rates required joining the BSS and rates set in HE capabilities.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.7023450fdf16.I194df59252097ba25a0a543456d4350f1607a538@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In UHB connection we don't have any HT/VHT elemens so in order to
calculate the max RX-NSS we need also to look at HE capa element, this
causes to limit us to max rx nss in UHB to 1.
Also anyway we need to look at HE max rx NSS and not only at HT/VHT
capa to determine the max rx nss over the connection.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.3713e0dea5dd.I3b9a15b4c53465c3f86f35459e9dc15ae4ea2abd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we're limiting bandwidth for some reason such as regulatory
restrictions, then advertise that limitation just like we do
for VHT today, so the AP is aware we cannot use the higher BW
it might be using.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20220202104617.70c8e3e7ee76.If317630de69ff1146bec7d47f5b83038695eb71d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the possible failure of the alloc, the ifmgd->assoc_req_ies might be
NULL pointer returned from kmemdup().
Therefore it might be better to free the skb and return error in order
to fail the association, like ieee80211_assoc_success().
Also, the caller, ieee80211_do_assoc(), needs to deal with the return
value from ieee80211_send_assoc().
Fixes: 4d9ec73d2b ("cfg80211: Report Association Request frame IEs in association events")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220105081559.2387083-1-jiasheng@iscas.ac.cn
[fix some paths to be errors, not success]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clang static analysis reports this warnings
mlme.c:5332:7: warning: Branch condition evaluates to a
garbage value
have_higher_than_11mbit)
^~~~~~~~~~~~~~~~~~~~~~~
have_higher_than_11mbit is only set to true some of the time in
ieee80211_get_rates() but is checked all of the time. So
have_higher_than_11mbit needs to be initialized to false.
Fixes: 5d6a1b069b ("mac80211: set basic rates earlier")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211223162848.3243702-1-trix@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* ndo_fill_forward_path support in mac80211, to let
drivers use it
* association comeback notification for userspace,
to be able to react more sensibly to long delays
* support for background radar detection hardware
in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
-----BEGIN PGP SIGNATURE-----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=u1jf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* ndo_fill_forward_path support in mac80211, to let drivers use it
* association comeback notification for userspace, to be able
to react more sensibly to long delays
* support for background radar detection hardware in some chipsets
* SA Query Procedures offload on the AP side
* more logging if we find problems with HT/VHT/HE
* various cleanups and minor fixes
Conflicts:
net/wireless/reg.c:
e08ebd6d7b ("cfg80211: Acquire wiphy mutex on regulatory work")
701fdfe348 ("cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface")
https://lore.kernel.org/r/20211221111950.57ecc6a7@canb.auug.org.au
drivers/net/wireless/ath/ath10k/wmi.c:
7f599aeccb ("cfg80211: Use the HE operation IE to determine a 6GHz BSS channel")
3bf2537ec2 ("ath10k: drop beacon and probe response which leak from other channel")
https://lore.kernel.org/r/20211221115004.1cd6b262@canb.auug.org.au
* tag 'mac80211-next-for-net-next-2021-12-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next: (32 commits)
cfg80211: Enable regulatory enforcement checks for drivers supporting mesh iface
rfkill: allow to get the software rfkill state
cfg80211: refactor cfg80211_get_ies_channel_number()
nl82011: clarify interface combinations wrt. channels
nl80211: Add support to offload SA Query procedures for AP SME device
nl80211: Add support to set AP settings flags with single attribute
mac80211: add more HT/VHT/HE state logging
cfg80211: Use the HE operation IE to determine a 6GHz BSS channel
cfg80211: rename offchannel_chain structs to background_chain to avoid confusion with ETSI standard
mac80211: Notify cfg80211 about association comeback
cfg80211: Add support for notifying association comeback
mac80211: introduce channel switch disconnect function
cfg80211: Fix order of enum nl80211_band_iftype_attr documentation
cfg80211: simplify cfg80211_chandef_valid()
mac80211: Remove a couple of obsolete TODO
mac80211: fix FEC flag in radio tap header
mac80211: use coarse boottime for airtime fairness code
ieee80211: change HE nominal packet padding value defines
cfg80211: use ieee80211_bss_get_elem() instead of _get_ie()
mac80211: Use memset_after() to clear tx status
...
====================
Link: https://lore.kernel.org/r/20211221112532.28708-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Submitting AP probe/null during suspend can cause unexpected
disconnect on resume because of timeout waiting for ack status:
wlan0: Failed to send nullfunc to AP 11:22:33:44:55:66 after 500ms, disconnecting
This is especially the case when we enter suspend when a scan is
ongoing, indeed, scan is cancelled from __ieee80211_suspend, leading
to a corresponding (aborted) scan complete event, which in turn causes
the submission of an immediate monitor null frame (restart_sta_timer).
The corresponding packet or ack will not be processed before resuming,
causing a timeout & disconnect on resume.
Delay the AP probing when suspending/suspended.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1634805927-1113-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define LC band which is a draft under IEEE 802.11bb.
Current NL80211_BAND_LC is a placeholder band and
will be more defined IEEE 802.11bb progresses.
Signed-off-by: Srinivasan Raju <srini.raju@purelifi.com>
Link: https://lore.kernel.org/r/20211018100143.7565-2-srini.raju@purelifi.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is to save the transmit power envelope element and power
constraint in struct ieee80211_bss_conf for 6 GHz. Lower driver
will use this info to calculate the power limit.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-7-wgong@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In function ieee80211_prep_channel(), it has some ieee80211_bss_get_ie()
and cfg80211_find_ext_ie() to get the IE, this is to use another
function ieee802_11_parse_elems() to get all the IEs in one time.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/20210924100052.32029-6-wgong@codeaurora.org
[remove now unnecessary size validation, use -ENOMEM, free elems earlier
for less error handling code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As the 802.11 spec evolves, we need to parse more and more
elements. This is causing the struct to grow, and we can no
longer get away with putting it on the stack.
Change the API to always dynamically allocate and return an
allocated pointer that must be kfree()d later.
As an alternative, I contemplated a scheme whereby we'd say
in the code which elements we needed, e.g.
DECLARE_ELEMENT_PARSER(elems,
SUPPORTED_CHANNELS,
CHANNEL_SWITCH,
EXT(KEY_DELIVERY));
ieee802_11_parse_elems(..., &elems, ...);
and while I think this is possible and will save us a lot
since most individual places only care about a small subset
of the elements, it ended up being a bit more work since a
lot of places do the parsing and then pass the struct to
other functions, sometimes with multiple levels.
Link: https://lore.kernel.org/r/20210920154009.26caff6b5998.I05ae58768e990e611aee8eca8abefd9d7bc15e05@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Notify the driver about the 4-address mode change and also send a nulldata
packet to the AP to notify it about the change
Fixes: 1ff4e8f2de ("mac80211: notify the driver when a sta uses 4-address mode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210702050111.47546-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit f39b07fdfb ("mac80211: HE STA disassoc
due to QOS NULL not sent")
Since iwlwifi specific workaround, which blocks to send NDP,
is removed, we can revert this commit.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20210623134826.10318-2-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have mgd_prepare_tx(), but sometimes drivers may want/need
to take action when the exchange finishes, whether successfully
or not.
Add a notification to the driver on completion, i.e. call the
new method mgd_complete_tx().
To unify the two scenarios, and to add more information, make
both of them take a struct that has the duration (prepare only),
subtype (both) and success (complete only).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.5d94e78f6230.I6dc979606b6f28701b740d7aab725f7853a5a155@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When sending an association request, add any vendor specific
capabilities at the end of the frame. This way, mac80211 is
still completely in charge of building the frame, but drivers
can determine what should be added depending on the band and
interface type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.80d716d69a5f.I28097ff19be6b22aebdc33a72795d2662755d41f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All uses of ieee80211_get_he_sta_cap() were actually wrong,
in net/mac80211/mlme.c they were wrong because that code is
also used for P2P (which is a different interface type), in
net/mac80211/main.c that should check all interface types.
Fix all that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.ede114bc8b46.Ibcd9a5d98430e936344eb6d242ef8a65c2f59b74@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP changes capability/bandwidth in some fashion, the
message might be somewhat misleading and we don't know what
really changed. Modify the message to speak about "caps/bw"
instead of just "bandwidth", and print out the flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.dc22c48985fa.I4bf5fbc17ec783c21d4b50c8c35b1de390896ccd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
chanctx represents the current phy configuration and rate scale uses
it for achieving max throughput, so if phy changes bandwidth to narrow
bandwidth, RC should be _first_ updated to avoid using the wider bandwidth
before updating the phy, and vice versa.
We assume in the patch that station interface is always updated before
updating phy context by calling ieee80211_vif_update_chandef.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.fc4e24496aa2.Ic40ea947c2f65739ea4b5fe3babd0a544240ced6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_mgd_assoc calls ieee80211_prep_connection which
might call ieee80211_prep_channel and set smps_mode to OFF.
That will override the previous setting of smps_mode in
ieee80211_mgd_assoc and HT SMPS will be set to "disabled"
in the association request frame.
Move the setting of smps_mode in ieee80211_mgd_assoc to
after the call to ieee80211_prep_connection.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.d8e5cc4b527f.Icf3a67fffbdd8c408c0cadfe43f8f4cffdc90acb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending nulldata packets is important for sw AP link probing and detecting
4-address mode links. The checks that dropped these packets were apparently
added to work around an iwlwifi firmware bug with multi-TID aggregation.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210619101517.90806-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
-----BEGIN PGP SIGNATURE-----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=b0NQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-04-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the frequency is invalid, ieee80211_parse_ch_switch_ie
will fail and we may not even reach the check in
ieee80211_sta_process_chanswitch. Drop the connection
in case ieee80211_parse_ch_switch_ie failed, but still
take into account the CSA mode to remember not to send
a deauth frame in case if it is forbidden to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.34712ef96a0a.I75d7ad7f1d654e8b0aa01cd7189ff00a510512b3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210408143124.b9e68aa98304.I465afb55ca2c7d59f7bf610c6046a1fd732b4c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The incorrect timeout check caused probing to happen when it did
not need to happen. This in turn caused tx performance drop
for around 5 seconds in ath10k-ct driver. Possibly that tx drop
is due to a secondary issue, but fixing the probe to not happen
when traffic is running fixes the symptom.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210330230749.14097-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We observed some Cisco APs sending the following HE Operation IE in
associate response:
ff 0a 24 f4 3f 00 01 fc ff 00 00 00
Its HE operation parameter is 0x003ff4, so the expected total length is
7 which does not match the actual length = 10. This causes association
failing with "HE AP is missing HE Capability/operation."
According to P802.11ax_D4 Table9-94, HE operation is extensible, and
according to 802.11-2016 10.27.8, STA should discard the part beyond
the maximum length and parse the truncated element.
Allow HE operation element to be longer than expected to handle this
case and future extensions.
Fixes: e4d005b80d ("mac80211: refactor extended element parsing")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org>
Link: https://lore.kernel.org/r/20210223051926.2653301-1-yenlinlai@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ssid info of ieee80211_bss_conf is filled in ieee80211_start_ap()
for AP mode. For STATION mode, it is empty, save the info from struct
ieee80211_mgd_assoc_data, the struct ieee80211_mgd_assoc_data will be
freed after assoc, so the ssid info of ieee80211_mgd_assoc_data can not
access after assoc, save ssid info to ieee80211_bss_conf, then ssid info
can be still access after assoc.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Link: https://lore.kernel.org/r/1607312195-3583-2-git-send-email-wgong@codeaurora.org
[reset on disassoc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I hit a bug in which we started a CSA with an action frame,
but the AP changed its mind and didn't change the beacon.
The CSA wasn't cancelled and we lost the connection.
The beacons were ignored because they never changed: they
never contained any CSA IE. Because they never changed, the
CRC of the beacon didn't change either which made us ignore
the beacons instead of processing them.
Now what happens is:
1) beacon has CRC X and it is valid. No CSA IE in the beacon
2) as long as beacon's CRC X, don't process their IEs
3) rx action frame with CSA
4) invalidate the beacon's CRC
5) rx beacon, CRC is still X, but now it is invalid
6) process the beacon, detect there is no CSA IE
7) abort CSA
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.83470b8407e6.I739b907598001362744692744be15335436b8351@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Updates to the 802.11ax draft are coming that deprecate the
country element in favour of the transmit power envelope
element, and make the maximum transmit power level field in
the triplets reserved, so if we parse them we'd use 0 dBm
transmit power.
Follow suit and completely ignore the element on 6 GHz for
purposes of determining TX power.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201206145305.9abf9f6b4f88.Icb6e52af586edcc74f1f0360e8f6fc9ef2bfe8f5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP advertises a band switch during CSA, we will not have
the right information to continue working with it, since it will
likely (have to) change its capabilities and we don't track any
capability changes at all. Additionally, we store e.g. supported
rates per band, and that information would become invalid.
Since this is a fringe scenario, just disconnect explicitly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201129172929.0e2327107c06.I461adb07704e056b054a4a7c29b80c95a9f56637@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the previous similar bugfix there was another bug here,
if no VHT elements were found we also disabled HE. Fix this to
disable HE only on the 5 GHz band; on 6 GHz it was already not
disabled, and on 2.4 GHz there need (should) not be any VHT.
Fixes: 57fa5e85d5 ("mac80211: determine chandef from HE 6 GHz operation")
Link: https://lore.kernel.org/r/20201013140156.535a2fc6192f.Id6e5e525a60ac18d245d86f4015f1b271fce6ee6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
last_rate is initialized to zero by sta_info_alloc(), but
this indicates legacy bitrate for the last TX rate (and
invalid for the last RX rate). To avoid a warning when
decoding the last rate as legacy (before a data frame
has been sent), initialize them as S1G MCS.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201005164522.18069-2-thomas@adapt-ip.com
[rename to ieee80211_s1g_sta_rate_init(), seems more appropriate]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_determine_chantype(), the sband->ht_cap was
being processed before S1G Operation element. Since the
HT capability element should not be present on the S1G
band, avoid processing potential garbage by moving the
call to ieee80211_apply_htcap_overrides() to after the S1G
block.
Also, in case of a missing S1G Operation element, we would
continue trying to process non-S1G elements (and return
with a channel width of 20MHz). Instead, just assume
primary channel is equal to operating and infer the
operating width from the BSS channel, then return.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20201001174748.24520-1-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a frame was acked and probe frames were sent, the connection monitoring
needs to be reset, otherwise it will keep probing until the connection is
considered dead, even though frames have been acked in the mean time.
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200927105605.97954-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The changes required for associating in S1G are:
- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G beacons are 802.11 Extension Frames, so the fixed
header part differs from regular beacons.
Add a handler to process S1G beacons and abstract out the
fetching of BSSID and element start locations in the
beacon body handler.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-14-thomas@adapt-ip.com
[don't rename, small coding style cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G allows listen interval up to 2^14 * 10000 beacon
intervals. In order to do this listen interval needs a
scaling factor applied to the lower 14 bits. Calculate
this and properly encode the listen interval for S1G STAs.
See IEEE802.11ah-2016 Table 9-44a for reference.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-10-thomas@adapt-ip.com
[move listen_int_usf into function using it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Include the S1G Capabilities element in an association
request, and support the cfg80211 capability overrides.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-5-thomas@adapt-ip.com
[pass skb to ieee80211_add_s1g_capab_ie(), small code style edits]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling mod_timer for every rx/tx packet can be quite expensive.
Instead of constantly updating the timer, we can simply let it run out
and check the timestamp of the last ACK or rx packet to re-arm it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-9-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211.h says: Beacon filter support is advertised with the
IEEE80211_VIF_BEACON_FILTER interface capability. The driver needs to
enable beacon filter support whenever power save is enabled, that is
IEEE80211_CONF_PS is set. When power save is enabled, the stack will
not check for beacon loss and the driver needs to notify about loss
of beacons with ieee80211_beacon_loss().
Some controllers may want to dynamically enable the beacon filter
capabilities on power save entry (CONF_PS) and disable it on exit.
This is the case for the wcn36xx driver which only supports beacon
filtering in PS mode (no CONNECTION_MONITOR support).
When the mac80211 beacon monitor timer expires, the beacon filter
flag must be checked again in case it as been changed in between
(e.g. vif moved to PS mode).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1592471863-31402-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE authentication has been extended with H2E (IEEE 802.11 REVmd) and PK
(WFA) options. Those extensions use special status code values in the
SAE commit messages (Authentication frame with transaction sequence
number 1) to identify which extension is in use. mac80211 was
interpreting those new values as the AP denying authentication and that
resulted in failure to complete SAE authentication in some cases.
Fix this by adding exceptions for the new status code values 126 and
127.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200731183830.18735-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg
Ilan Peer
Lian Chen
Jakub Kicinski
Muna Sinada
Manikanta Pubbisetty
Sriram R
Youghandhar Chintala
Mordechay Goodstein
Jiasheng Jiang
Tom Rix
Loic Poulain
Srinivasan Raju
Wen Gong
Felix Fietkau
Ping-Ke Shih
Zheng Yongjun
Shaul Triebitz
David S. Miller
Naftali Goldstein
Emmanuel Grumbach
Ben Greear
Brian Norris
Thomas Pedersen
Jouni Malinen