of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Guobin Huang <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was only enabling the first clock on the device, regardless
of its name. However, this controller logic can have multiple clocks
which should all be enabled. Add support for enabling additional clocks.
The clock names used are matching those used in the Xilinx version of this
driver as well as the Xilinx device tree generator, except for mgt_clk
which is not present there.
For backward compatibility, if no named clocks are present, the first
clock present is used for determining the MDIO bus clock divider.
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In setups with fixed-link settings there is no mdio node in DTS.
axienet_probe() already handles that gracefully but lp->mii_bus is
then NULL.
Fix code that tries to blindly grab the MDIO lock by introducing two helper
functions that make the locking conditional.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver did not always clean up all allocated resources when probe
failed. Fix the probe cleanup path to clean up everything that was
allocated.
Fixes: 57baf8cc70 ("net: axienet: Handle deferred probe on clock properly")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the Xilinx AXI Ethernet core (specifically version 7.2 or
later) allow the core to be configured with a PHY interface mode of "Both",
allowing either 1000BaseX or SGMII modes to be selected at runtime. Add
support for this in the driver to allow better support for applications
which can use both fiber and copper SFP modules.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hook up the nway_reset ethtool operation to the corresponding phylink
function so that "ethtool -r" can be supported.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is set up to use a clock mapping in the device tree if it is
present, but still work without one for backward compatibility. However,
if getting the clock returns -EPROBE_DEFER, then we need to abort and
return that error from our driver initialization so that the probe can
be retried later after the clock is set up.
Move clock initialization to earlier in the process so we do not waste as
much effort if the clock is not yet available. Switch to use
devm_clk_get_optional and abort initialization on any error reported.
Also enable the clock regardless of whether the controller is using an MDIO
bus, as the clock is required in any case.
Fixes: 09a0354cad ("net: axienet: Use clock framework to get device clock rate")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO spec does not require an MDC at all times, only when MDIO
transactions are occurring. This patch allows the xilinx_axienet
driver to disable the MDC when not in use, and re-enable it when
needed. It also simplifies the driver by removing MDC disable
and enable in device reset sequence.
Signed-off-by: Clayton Rayment <clayton.rayment@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update the axienet driver to properly support the Xilinx PCS/PMA PHY
component which is used for 1000BaseX and SGMII modes, including
properly configuring the auto-negotiation mode of the PHY and reading
the negotiated state from the PHY.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20201028171429.1699922-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With all DMA address accesses wrapped, we can actually support 64-bit
DMA if this option was chosen at IP integration time.
If the IP has been configured for an address width greater than 32 bits,
we assume the full 64 bit DMA width is working. In practise this will be
limited by the actual system address bus width, which will ideally be the
same as the DMA IP address width.
If this is not the case, the actual width can still be configured using a
dma-ranges property in the parent of the MAC node.
This increases the DMA mask on those systems to let the kernel choose
buffers from memory at higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When newer revisions of the Axienet IP are configured for a 64-bit bus,
we *need* to write to the MSB part of the an address registers,
otherwise the IP won't recognise this as a DMA start condition.
This is even true when the actual DMA address comes from the lower 4 GB.
To autodetect this configuration, at probe time we write all 1's to such
an MSB register, and see if any bits stick. If this is configured for a
32-bit bus, those MSB registers are RES0, so reading back 0 indicates
that no MSB writes are necessary.
On the other hands reading anything other than 0 indicated the need to
write the MSB registers, so we set the respective flag.
The actual DMA mask stays at 32-bit for now. To help bisecting, a
separate patch will enable allocations from higher addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer revisions of the AXI DMA IP (>= v7.1) support 64-bit addresses,
both for the descriptors itself, as well as for the buffers they are
pointing to.
This is realised by adding "MSB" words for the next and phys pointer
right behind the existing address word, now named "LSB". These MSB words
live in formerly reserved areas of the descriptor.
If the hardware supports it, write both words when setting an address.
The buffer address is handled by two wrapper functions, the two
occasions where we set the next pointers are open coded.
For now this is guarded by a flag which we don't set yet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer versions of the Xilink DMA IP support busses with more than 32
address bits, by introducing an MSB word for the registers holding DMA
pointers (tail/current, RX/TX descriptor addresses).
On IP configured for more than 32 bits, it is also *required* to write
both words, to let the IP recognise this as a start condition for an
MM2S request, for instance.
Wrap the DMA pointer writes with a separate function, to add this
functionality later. For now we stick to the lower 32 bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii-tool is useful for debugging, and all it requires to work is to wire
up the ioctl ops function pointer.
Add this to the axienet driver to enable mii-tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer revisions of the IP don't have these registers. Since we don't
really use them, just drop them from the ethtools dump.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the DT binding, the Ethernet core interrupt is optional.
Use platform_get_irq_optional() to avoid the error message when the
IRQ is not specified.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Especially with the default 32-bit DMA mask, DMA buffers are a limited
resource, so their allocation can fail.
So as the DMA API documentation requires, add error checking code after
dma_map_single() calls to catch the case where we run out of "low" memory.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the code that cleans up a number of connected TX descriptors,
as we will need it to properly roll back a failed _xmit() call.
There are subtle differences between cleaning up a successfully sent
chain (unknown number of involved descriptors, total data size needed)
and a chain that was about to set up (number of descriptors known), so
cater for those variations with some extra parameters.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 0 is a valid DMA address, we cannot use the physical address to
check whether a TX descriptor is valid and is holding a DMA mapping.
Use the "cntrl" member of the descriptor to make this decision, as it
contains at least the length of the buffer, so 0 points to an
uninitialised buffer.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When axienet_dma_bd_init() bails out during the initialisation process,
it might do so with parts of the structure already allocated and
initialised, while other parts have not been touched yet. Before
returning in this case, we call axienet_dma_bd_release(), which does not
take care of this corner case.
This is most obvious by the first loop happily dereferencing
lp->rx_bd_v, which we actually check to be non NULL *afterwards*.
Make sure we only unmap or free already allocated structures, by:
- directly returning with -ENOMEM if nothing has been allocated at all
- checking for lp->rx_bd_v to be non-NULL *before* using it
- only unmapping allocated DMA RX regions
This avoids NULL pointer dereferences when initialisation fails.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail allocating the DMA buffers in axienet_dma_bd_init(), we
report this error, but carry on with initialisation nevertheless.
This leads to a kernel panic when the driver later wants to send a
packet, as it uses uninitialised data structures.
Make the axienet_device_reset() routine return an error value, as it
contains the DMA buffer initialisation. Make sure we propagate the error
up the chain and eventually fail the driver initialisation, to avoid
relying on non-initialised buffers.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA error handler routine is currently a tasklet, scheduled to run
after the DMA error IRQ was handled.
However it needs to take the MDIO mutex, which is not allowed to do in a
tasklet. A kernel (with debug options) complains consequently:
[ 614.050361] net eth0: DMA Tx error 0x174019
[ 614.064002] net eth0: Current BD is at: 0x8f84aa0ce
[ 614.080195] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[ 614.109484] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 40, name: kworker/u4:4
[ 614.135428] 3 locks held by kworker/u4:4/40:
[ 614.149075] #0: ffff000879863328 ((wq_completion)rpciod){....}, at: process_one_work+0x1f0/0x6a8
[ 614.177528] #1: ffff80001251bdf8 ((work_completion)(&task->u.tk_work)){....}, at: process_one_work+0x1f0/0x6a8
[ 614.209033] #2: ffff0008784e0110 (sk_lock-AF_INET-RPC){....}, at: tcp_sendmsg+0x24/0x58
[ 614.235429] CPU: 0 PID: 40 Comm: kworker/u4:4 Not tainted 5.6.0-rc3-00926-g4a165a9d5921 #26
[ 614.260854] Hardware name: ARM Test FPGA (DT)
[ 614.274734] Workqueue: rpciod rpc_async_schedule
[ 614.289022] Call trace:
[ 614.296871] dump_backtrace+0x0/0x1a0
[ 614.308311] show_stack+0x14/0x20
[ 614.318751] dump_stack+0xbc/0x100
[ 614.329403] ___might_sleep+0xf0/0x140
[ 614.341018] __might_sleep+0x4c/0x80
[ 614.352201] __mutex_lock+0x5c/0x8a8
[ 614.363348] mutex_lock_nested+0x1c/0x28
[ 614.375654] axienet_dma_err_handler+0x38/0x388
[ 614.389999] tasklet_action_common.isra.15+0x160/0x1a8
[ 614.405894] tasklet_action+0x24/0x30
[ 614.417297] efi_header_end+0xe0/0x494
[ 614.429020] irq_exit+0xd0/0xd8
[ 614.439047] __handle_domain_irq+0x60/0xb0
[ 614.451877] gic_handle_irq+0xdc/0x2d0
[ 614.463486] el1_irq+0xcc/0x180
[ 614.473451] __tcp_transmit_skb+0x41c/0xb58
[ 614.486513] tcp_write_xmit+0x224/0x10a0
[ 614.498792] __tcp_push_pending_frames+0x38/0xc8
[ 614.513126] tcp_rcv_established+0x41c/0x820
[ 614.526301] tcp_v4_do_rcv+0x8c/0x218
[ 614.537784] __release_sock+0x5c/0x108
[ 614.549466] release_sock+0x34/0xa0
[ 614.560318] tcp_sendmsg+0x40/0x58
[ 614.571053] inet_sendmsg+0x40/0x68
[ 614.582061] sock_sendmsg+0x18/0x30
[ 614.593074] xs_sendpages+0x218/0x328
[ 614.604506] xs_tcp_send_request+0xa0/0x1b8
[ 614.617461] xprt_transmit+0xc8/0x4f0
[ 614.628943] call_transmit+0x8c/0xa0
[ 614.640028] __rpc_execute+0xbc/0x6f8
[ 614.651380] rpc_async_schedule+0x28/0x48
[ 614.663846] process_one_work+0x298/0x6a8
[ 614.676299] worker_thread+0x40/0x490
[ 614.687687] kthread+0x134/0x138
[ 614.697804] ret_from_fork+0x10/0x18
[ 614.717319] xilinx_axienet 7fe00000.ethernet eth0: Link is Down
[ 615.748343] xilinx_axienet 7fe00000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
Since tasklets are not really popular anymore anyway, lets convert this
over to a work queue, which can sleep and thus can take the MDIO mutex.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver already correctly rejected all unsupported
parameters. No functional changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the Xilinx AXI ethernet driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the resolved link parameters via the mac_link_up() call for
MACs that do not automatically track their PCS state. We propagate the
link parameters via function arguments so that inappropriate members
of struct phylink_link_state can't be accessed, and creating a new
structure just for this adds needless complexity to the API.
Tested-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the mac_link_state() method to mac_pcs_get_state() to make it
clear that it should be returning the MACs PCS current state, which
is used for inband negotiation rather than just reading back what the
MAC has been configured for. Update the documentation to explicitly
mention that this is for inband.
We drop the return value as well; most of phylink doesn't check the
return value and it is not clear what it should do on error - instead
arrange for state->link to be false.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "lp->phy_mode" is an enum but in this context GCC treats it as an
unsigned int so the error handling is never triggered.
Fixes: ee06b1728b ("net: axienet: add support for standard phy-mode binding")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible use-after-free issue in the axienet_probe():
1701: np = of_parse_phandle(pdev->dev.of_node, "axistream-connected", 0);
1702: if (np) {
...
1787: of_node_put(np); ---> released here
1788: lp->eth_irq = platform_get_irq(pdev, 0);
1789: } else {
...
1801: }
1802: if (IS_ERR(lp->dma_regs)) {
...
1805: of_node_put(np); ---> double released here
1806: goto free_netdev;
1807: }
We solve this problem by removing the unnecessary of_node_put().
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Robert Hancock <hancock@sedsystems.ca>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were accessing the pointer returned from platform_get_resource before
checking if it was valid, causing an oops if it was not. Move this access
after the call to devm_ioremap_resource which does the validity check.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert this driver to use the phylink API rather than the legacy PHY
API. This allows for better support for SFP modules connected using a
1000BaseX or SGMII interface.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the axienet driver requires the use of a second devicetree
node, referenced by an axistream-connected attribute on the Ethernet
device node, which contains the resources for the AXI DMA block used by the
device. This setup is problematic for a use case we have where the Ethernet
and DMA cores are behind a PCIe to AXI bridge and the memory resources for
the nodes are injected into the platform devices using the multifunction
device subsystem - it's not easily possible for the driver to obtain the
platform-level resources from the linked device.
In order to simplify that usage model, and simplify the overall use of
this driver in general, allow for all of the resources to be kept on one
node where the resources are retrieved using platform device APIs rather
than device-tree-specific ones. The previous usage setup is still
supported if the axistream-connected attribute is specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, such as iMX6 with PCIe devices, crashes or hangs can
occur if the axienet device continues to perform DMA transfers after
parent devices/busses have been shut down. Shut down the axienet
interface during its shutdown callback in order to avoid this.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failing initialization on a missing MAC address property is excessive.
We can just fall back to using a random MAC instead, which at least
leaves the interface in a functioning state.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that the interrupt handler fires and frees up space in
the TX ring in between checking for sufficient TX ring space and
stopping the TX queue in axienet_start_xmit. If this happens, the
queue wake from the interrupt handler will occur before the queue is
stopped, causing a lost wakeup and the adapter's transmit hanging.
To avoid this, after stopping the queue, check again whether there is
sufficient space in the TX ring. If so, wake up the queue again.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this driver only handled interrupts from the DMA RX and TX
blocks, not from the Ethernet core itself. Add optional support for
the Ethernet core interrupt, which is used to detect rx_missed and
framing errors signalled by the hardware. In order to use this
interrupt, a third interrupt needs to be specified in the device tree.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specify IRQF_SHARED to support shared interrupts. If the interrupt
handler is called and the device is not indicating an interrupt,
just return IRQ_NONE rather than spewing error messages.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
These registers are important for troubleshooting the state of the DMA
cores.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Xilinx DMA blocks each have their own reset register, but they both
reset the entire DMA engine, so only one of them needs to be reset.
Also, when stopping the device, we need to not just command the DMA
blocks to stop, but wait for them to stop, and trigger a device reset
to ensure that they are completely stopped.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO clock divisor register setting was only applied on the initial
startup when the driver was loaded. However, this setting is cleared
when the device is reset, such as would occur when the interface was
taken down and brought up again, and so the MDIO bus would be
non-functional afterwards.
Split up the MDIO bus setup and enable into separate functions and
re-enable the bus after a device reset, to ensure that the MDIO
registers are set properly. This also allows us to remove direct access
to MDIO registers in xilinx_axienet_main.c and centralize them all in
xilinx_axienet_mdio.c.
Also, lock the MDIO bus lock around the device reset process, to avoid
MDIO accesses from occurring while the MDIO is disabled during the reset.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the MDIO is is brought up before the netdev is registered, it
should be torn down after the netdev is removed. Otherwise, PHY accesses
can potentially access freed MDIO bus references and cause a crash.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.
Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus for this driver was being named using the result of
of_address_to_resource on a node which may not have any resource on it,
but the return value of that call was not checked so it was using some
random value in the bus name. Change to name the MDIO bus based on the
resource start of the actual Ethernet register block.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was using in_be32 and out_be32 IO accessors which do not
exist on most platforms. Also, the use of big-endian accessors does not
seem correct as this hardware is accessed over an AXI bus which, to the
extent it has an endian-ness, is little-endian. Switch to standard
ioread32/iowrite32 accessors.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was casting skb pointers to u32 and storing them as such in
the DMA buffer descriptor, which is obviously broken on 64-bit. The area
of the buffer descriptor being used is not accessed by the hardware and
has sufficient room for a 32 or 64-bit pointer, so just store the skb
pointer as such.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was NVMEM support added to of_get_mac_address, so it could now
return ERR_PTR encoded error values, so we need to adjust all current
users of of_get_mac_address to this new fact.
While at it, remove superfluous is_valid_ether_addr as the MAC address
returned from of_get_mac_address is always valid and checked by
is_valid_ether_addr anyway.
Fixes: d01f449c00 ("of_net: add NVMEM support to of_get_mac_address")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/ethernet/xilinx/xilinx_axienet_main.c:1624:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1569, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
axienet_open no longer return -ENODEV when PHY cannot be connected to
since commit d7cc3163e0 ("net: axienet: Support phy-less mode of operation")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep supporting proprietary "xlnx,phy-type" attribute and add support for
MII connectivity to the PHY.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random MAC address in order to make
sure ndev->addr_assign_type will be properly set to NET_ADDR_RANDOM.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not open code getting the MAC address exclusively from the
"local-mac-address" property, but instead use of_get_mac_address()
which looks up the MAC address using the 3 typical property names.
Also avoid casting away the const qualifier of the return value by
making axienet_set_mac_address() take a const void* address.
Follows commit b34296a9c0 ("net: ethoc: Utilize
of_get_mac_address()").
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somehow, I missed a healthy number of ethernet drivers in the last pass.
Most of these drivers either were in need of an updated max_mtu to make
jumbo frames possible to enable again. In a few cases, also setting a
different min_mtu to match previous lower bounds. There are also a few
drivers that had no upper bounds checking, so they're getting a brand new
ETH_MAX_MTU that is identical to IP_MAX_MTU, but accessible by includes
all ethernet and ethernet-like drivers all have already.
acenic:
- min_mtu = 0, max_mtu = 9000
amazon/ena:
- min_mtu = 128, max_mtu = adapter->max_mtu
amd/xgbe:
- min_mtu = 0, max_mtu = 9000
sb1250:
- min_mtu = 0, max_mtu = 1518
cxgb3:
- min_mtu = 81, max_mtu = 65535
cxgb4:
- min_mtu = 81, max_mtu = 9600
cxgb4vf:
- min_mtu = 81, max_mtu = 65535
benet:
- min_mtu = 256, max_mtu = 9000
ibmveth:
- min_mtu = 68, max_mtu = 65535
ibmvnic:
- min_mtu = adapter->min_mtu, max_mtu = adapter->max_mtu
- remove now redundant ibmvnic_change_mtu
jme:
- min_mtu = 1280, max_mtu = 9202
mv643xx_eth:
- min_mtu = 64, max_mtu = 9500
mlxsw:
- min_mtu = 0, max_mtu = 65535
- Basically bypassing the core checks, and instead relying on dynamic
checks in the respective switch drivers' ndo_change_mtu functions
ns83820:
- min_mtu = 0
- remove redundant ns83820_change_mtu, only checked for mtu > 1500
netxen:
- min_mtu = 0, max_mtu = 8000 (P2), max_mtu = 9600 (P3)
qlge:
- min_mtu = 1500, max_mtu = 9000
- driver only supports setting mtu to 1500 or 9000, so the core check only
rules out < 1500 and > 9000, qlge_change_mtu still needs to check that
the value is 1500 or 9000
qualcomm/emac:
- min_mtu = 46, max_mtu = 9194
xilinx_axienet:
- min_mtu = 64, max_mtu = 9000
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
CC: netdev@vger.kernel.org
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Netanel Belgazal <netanel@annapurnalabs.com>
CC: Tom Lendacky <thomas.lendacky@amd.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
CC: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
CC: John Allen <jallen@linux.vnet.ibm.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Ido Schimmel <idosch@mellanox.com>
CC: Manish Chopra <manish.chopra@qlogic.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Rajesh Borundia <rajesh.borundia@qlogic.com>
CC: Timur Tabi <timur@codeaurora.org>
CC: Anirudha Sarangi <anirudh@xilinx.com>
CC: John Linn <John.Linn@xilinx.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev parameter passed to __axienet_device_reset() is not used inside
the function, so remove it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival fix, dev_err messages are missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 46aa27df88 ('net: axienet: Use devm_* calls')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value returned by devm_ioremap_resource() was checked for non-NULL but
devm_ioremap_resource() returns IOMEM_ERR_PTR, not NULL. In case of
error this could lead to dereference of ERR_PTR.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Cc: <stable@vger.kernel.org>
Fixes: 46aa27df88 ("net: axienet: Use devm_* calls")
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize names with other drivers.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_* calls
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use devm_* calls
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize names with other drivers
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is rule for network drivers with comments blocks
which is newly checked by checkpatch.pl script.
Let's fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed checkpatch.pl errors and warnings.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds proper checks to handle the PHY-less case.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, jumbo frames are supported only
for the frame sizes > 16K. This patch corrects this logic to
handle jumbo frames for lesser frame sizes (< 16K) ensuring jumbo frame
MTU is within the limit of max frame size configured in the h/w
design.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet completion interrupts for TX and RX should be serviced before
the packets are consumed. This ensures against the degenerate case when a
new completion interrupt is raised after the handler has exited but before
the interrupts are cleared. In this case its possible for the ISR to clear
an unhandled interrupt (leading to potential deadlock).
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AXI-DMA rx-delay interrupt can sometimes be triggered
when there are 0 outstanding packets received. This is due
to the fact that the receive function will greedily consume
as many packets as possible on interrupt. So if two packets
(with a very particular timing) arrive in succession they
will each cause the rx-delay interrupt, but the first interrupt
will consume both packets.
This means the second interrupt is a 0 packet receive.
This is mostly OK, except that the tail pointer register is
updated unconditionally on receive. Currently the tail pointer
is always set to the current bd-ring descriptor under
the assumption that the hardware has moved onto the next
descriptor. What this means for length 0 recv is the current
descriptor that the hardware is potentially yet to use will
be marked as the tail. This causes the hardware to think
its run out of descriptors deadlocking the whole rx path.
Fixed by updating the tail pointer to the most recent
successfully consumed descriptor.
Reported-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Tested-by: Jason Wu <huanyu@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RGMII. The h/w configuration
parameter C_PHY_TYPE, which represents the interface configured in
the design, is used to differentiate various interfaces supported
by AXI Ethernet.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This property is no longer used in the code yet the code looks for it in the device tree.
It does not cause an error if it's not in the tree.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling ether_setup is redundant since alloc_etherdev calls
it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning log:
xilinx_axienet_main.c: In function 'axienet_start_xmit_done':
xilinx_axienet_main.c:617:16: warning: operation on 'lp->tx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_start_xmit':
xilinx_axienet_main.c:703:18: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c:719:17: warning: operation on 'lp->tx_bd_tail' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_recv':
xilinx_axienet_main.c:792:16: warning: operation on 'lp->rx_bd_ci' may be undefined [-Wsequence-point]
xilinx_axienet_main.c: In function 'axienet_of_probe':
xilinx_axienet_main.c:1501:21: warning: unused variable 'rc' [-Wunused-variable]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few network drivers really supports frag_list : virtual drivers.
Some drivers wrongly advertise NETIF_F_FRAGLIST feature.
If skb with a frag_list is given to them, packet on the wire will be
corrupt.
Remove this flag, as core networking stack will make sure to
provide packets that can be sent without corruption.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_ZERO is an uncommon flag and perhaps is better
not used. static inline dma_zalloc_coherent exists
so convert the uses of dma_alloc_coherent with __GFP_ZERO
to the more common kernel style with zalloc.
Remove memset from the static inline dma_zalloc_coherent
and add just one use of __GFP_ZERO instead.
Trivially reduces the size of the existing uses of
dma_zalloc_coherent.
Realign arguments as appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of calls required to alloc
a zeroed block of memory.
Trivially reduces overall object size.
Other changes around these removals
o Neaten call argument alignment
o Remove an unnecessary OOM message after dma_alloc_coherent failure
o Remove unnecessary gfp_t stack variable
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Walle
Jakub Kicinski
Guobin Huang
Robert Hancock
Daniel Mack
David S. Miller
Clayton Rayment
Zhang Changzhong
Andre Przywara
Russell King
Wei Yongjun
Andrew Lunn
Dan Carpenter
Wen Yang
Robert Hancock
Thomas Gleixner
Petr Štetiar
Yang Wei
Luis Chamberlain
YueHaibing
Alvaro G. M
Tobias Klauser
Jarod Wilson
Colin Ian King
Julia Lawall
Wei Yongjun
Philippe Reynes
Florian Westphal
Ivan Vecera
Krzysztof Kozlowski
Michal Simek
Srikanth Thokala
Peter Crosthwaite
Fabian Frederick
Appana Durga Kedareswara Rao
Subbaraya Sundeep Bhatta
Joe Perches
Paul Gortmaker
Eric Dumazet
Jingoo Han