Use more inclusive terms throughout the DSA subsystem by moving away
from "master" which is replaced by "conduit" and "slave" which is
replaced by "user". No functional changes.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mv88e6xxx_tai_write() can return error code (-EOPNOTSUPP ...) if failed.
So check the value of 'ret' after calling mv88e6xxx_tai_write().
Signed-off-by: Su Hui <suhui@nfschina.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 23d775f12d ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12d ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the const read-only array lanes on the stack, instead make
it static.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/sfc/tc.c
fa165e1949 ("sfc: don't unregister flow_indr if it was never registered")
3bf969e88a ("sfc: add MAE table machinery for conntrack table")
https://lore.kernel.org/all/20230818112159.7430e9b4@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the switch is reset during active EEPROM transactions, as in
just after an SoC reset after power up, the I2C bus transaction
may be cut short leaving the EEPROM internal I2C state machine
in the wrong state. When the switch is reset again, the bad
state machine state may result in data being read from the wrong
memory location causing the switch to enter unexpected mode
rendering it inoperational.
Fixes: a3dcb3e7e7 ("net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset")
Signed-off-by: Alfred Lee <l00g33k@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230815001323.24739-1-l00g33k@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes XAUI/RXAUI lane alignment errors.
Issue causes dropped packets when trying to communicate over
fiber via SERDES lanes of port 9 and 10.
Errata document applies only to 88E6190X and 88E6390X devices.
Requires poking in undocumented registers.
Signed-off-by: Ante Knezic <ante.knezic@helmholz.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230724211859.805481-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since DSA no longer marks anything as phylink-legacy, there is now no
need for DSA drivers to set this member to false. Remove all instances
of this.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that mv88e6xxx is completely converted to using phylink_pcs
support, we have no need for the serdes methods. Remove all this
infrastructure. Also remove the __maybe_unused from
mv88e6xxx_pcs_select().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6390, 88E6390X, and 88E6393X family of switches to use
the phylink_pcs infrastructure.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6352 SERDES code to use the phylink_pcs infrastructure.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6185 SERDES code to use the phylink_pcs infrastructure.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename and export the PCS state decoding function so our PCS can
make use of the functionality provided by this.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure for phylink_pcs to the mv88e6xxx driver. This
involves adding a mac_select_pcs() hook so we can pass the PCS to
phylink at the appropriate time, and a PCS initialisation function.
As the various chip implementations are converted to use phylink_pcs,
they are no longer reliant on the legacy phylink behaviour. We detect
this by the use of this infrastructure, or the lack of any serdes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we now always use a fixed-link for DSA and CPU ports, we no longer
need the hack in the Marvell code to make this work. Remove it.
This is especially important with the conversion of DSA drivers to
phylink_pcs, as the PCS code only gets called if we are using
phylink for the port.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I get sporadic timeouts from the driver when using the
MV88E6352. Reading the status again after the loop fixes the
problem: the operation is successful but goes undetected.
Some added prints show things like this:
[ 58.356209] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1b reg 0b, mask 8000, val 0000, data c000
[ 58.367487] mv88e6085 mdio_mux-0.1:00: Timeout waiting for
ATU op 4000, fid 0001
(...)
[ 61.826293] mv88e6085 mdio_mux-0.1:00: Timeout while waiting
for switch, addr 1c reg 18, mask 8000, val 0000, data 9860
[ 61.837560] mv88e6085 mdio_mux-0.1:00: Timeout waiting
for PHY command 1860 to complete
The reason is probably not the commands: I think those are
mostly fine with the 50+50ms timeout, but the problem
appears when OpenWrt brings up several interfaces in
parallel on a system with 7 populated ports: if one of
them take more than 50 ms and waits one or more of the
others can get stuck on the mutex for the switch and then
this can easily multiply.
As we sleep and wait, the function loop needs a final
check after exiting the loop if we were successful.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Cc: Tobias Waldekranz <tobias@waldekranz.com>
Fixes: 35da1dfd94 ("net: dsa: mv88e6xxx: Improve performance of busy bit polling")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230712223405.861899-1-linus.walleij@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de4 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A mv88e6250 family switch with 5 internal PHYs, 2 RMIIs
and no PTP support.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A mv88e6250 family switch with 2 PHY and RMII ports and
no PTP support.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switches from mv88e6250 family (including mv88e6020 and mv88e6071) need
the possibility to setup the maximal frame size, as they support frames
up to 2048 bytes.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E6361 is an 8-port switch derived from the
88E6393X/88E9193X/88E6191X switches family. It can benefit from the
existing mv88e6xxx driver by simply adding the proper switch description in
the driver. Main differences with other switches from this
family are:
- 8 ports exposed (instead of 11): ports 1, 2 and 8 not available
- No 5GBase-x nor SFI/USXGMII support
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some switches families have minor differences on supported link speed for
ports. Instead of redefining a new port_max_speed_mode for each different
configuration, allow to pass mv88e6xxx_chip structure to allow
differentiating those chips by known chip id
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
88E6393X/88E6193X/88E6191X switches have in fact 8 internal PHYs, but those
are not present starting at port 0: supported ports go from 1 to 8
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mv88e6xxx currently assumes that switch equipped with internal phys have
those phys mapped contiguously starting from port 0 (see
mv88e6xxx_phy_is_internal). However, some switches have internal PHYs but
NOT starting from port 0. For example 88e6393X, 88E6193X and 88E6191X have
integrated PHYs available on ports 1 to 8
To properly support this offset, add a new field to allow specifying an
internal PHYs layout. If field is not set, default layout is assumed (start
at port 0)
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure to use existing helper to get internal PHYs count instead of
redoing it manually
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since this function is a simple helper, we do not need to pass a full
dsa_switch structure, we can directly pass the mv88e6xxx_chip structure.
Doing so will allow to share this function with any other function
not manipulating dsa_switch structure but needing info about number of
internal phys
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the link forcing out of mac_config() and into the mac_prepare()
and mac_finish() methods. This results in no change to the order in
which these operations are performed, but does mean when we convert
mv88e6xxx to phylink_pcs support, we will continue to preserve this
ordering.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marco Migliore <m.migliore@tiesse.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rsvd2cpu capability for mv88e6321 model, to allow proper bpdu
processing.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Fixes: 51c901a775 ("net: dsa: mv88e6xxx: distinguish Global 2 Rsvd2CPU")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch can either take the MAC or the PHY role in an MII or RMII
link. There are distinct PHY_INTERFACE_ macros for these two roles.
Correct the mapping so that the `REV` version is used for the PHY
role.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230411023541.2372609-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The force watchdog event bit is not cleared during SW reset in the
mv88e6393x switch. This is a different behavior compared to mv886390 which
clears the force WD event bit as advertised. This causes a force WD event
to be handled over and over again as the SW reset following the event never
clears the force WD event bit.
Explicitly clear the watchdog event register to 0 in irq_action when
handling an event to prevent the switch from sending continuous interrupts.
Marvell aren't aware of any other stuck bits apart from the force WD
bit.
Fixes: de776d0d31 ("net: dsa: mv88e6xxx: add support for mv88e6393x family"
Signed-off-by: Gustav Ekelund <gustaek@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Do not set the MV88E6XXX_PORT_CTL0_IGMP_MLD_SNOOP bit on CPU or DSA ports.
This allows the host CPU port to be a regular IGMP listener by sending out
IGMP Membership Reports, which would otherwise not be forwarded by the
mv88exxx chip, but directly looped back to the CPU port itself.
Fixes: 54d792f257 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Steffen Bätz <steffen@innosonix.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20230329150140.701559-1-festevam@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 2c7e46edbd ("net: dsa: mv88e6xxx: mask apparently non-existing
phys during probing") added non-trivial bus->phy_mask in
mv88e6xxx_mdio_register() in order to avoid excessive mdio bus
transactions during probing.
But the mask is incorrect for switches with non-zero phy_base_addr (such
as 88E6341).
Fix this.
Fixes: 2c7e46edbd ("net: dsa: mv88e6xxx: mask apparently non-existing phys during probing")
Signed-off-by: Marek Behún <kabel@kernel.org>
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20230319140238.9470-1-kabel@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
To avoid excessive mdio bus transactions during probing, mask all phy
addresses that do not exist (there is a 1:1 mapping between switch port
number and phy address).
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Call the rather expensive mv88e6xxx_mdios_register() at the beginning of
mv88e6xxx_setup(). This avoids the double call via mv88e6xxx_probe()
during boot.
For symmetry, call mv88e6xxx_mdios_unregister() at the end of
mv88e6xxx_teardown().
Link: https://lore.kernel.org/lkml/449bde236c08d5ab5e54abd73b645d8b29955894.camel@gmail.com/
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move mv88e6xxx_setup() below mv88e6xxx_mdios_register(), so that we are
able to call the latter one from here. Do the same thing for the
inverse functions.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
irq_find_mapping() does not need irq_dispose_mapping(), only
irq_create_mapping() does.
Calling irq_dispose_mapping() from mv88e6xxx_g2_irq_mdio_free() and from
the error path of mv88e6xxx_g2_irq_mdio_setup() effectively means that
the mdiobus logic (for internal PHY interrupts) is disposing of a
hwirq->virq mapping which it is not responsible of (but instead, the
function pair mv88e6xxx_g2_irq_setup() + mv88e6xxx_g2_irq_free() is).
With the current code structure, this isn't such a huge problem, because
mv88e6xxx_g2_irq_mdio_free() is called relatively close to the real
owner of the IRQ mappings:
mv88e6xxx_remove()
-> mv88e6xxx_unregister_switch()
-> mv88e6xxx_mdios_unregister()
-> mv88e6xxx_g2_irq_mdio_free()
-> mv88e6xxx_g2_irq_free()
and the switch isn't 'live' in any way such that it would be able of
generating interrupts at this point (mv88e6xxx_unregister_switch() has
been called).
However, there is a desire to split mv88e6xxx_mdios_unregister() and
mv88e6xxx_g2_irq_free() such that mv88e6xxx_mdios_unregister() only gets
called from mv88e6xxx_teardown(). This is much more problematic, as can
be seen below.
In a cross-chip scenario (say 3 switches d0032004.mdio-mii:10,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 which form a single DSA
tree), it is possible to unbind the device driver from a single switch
(say d0032004.mdio-mii:10).
When that happens, mv88e6xxx_remove() will be called for just that one
switch, and this will call mv88e6xxx_unregister_switch() which will tear
down the entire tree (calling mv88e6xxx_teardown() for all 3 switches).
Assuming mv88e6xxx_mdios_unregister() was moved to mv88e6xxx_teardown(),
at this stage, all 3 switches will have called irq_dispose_mapping() on
their mdiobus virqs.
When we bind again the device driver to d0032004.mdio-mii:10,
mv88e6xxx_probe() is called for it, which calls dsa_register_switch().
The DSA tree is now complete again, and mv88e6xxx_setup() is called for
all 3 switches.
Also assuming that mv88e6xxx_mdios_register() is moved to
mv88e6xxx_setup() (the 2 assumptions go together), at this point,
d0032004.mdio-mii:11 and d0032004.mdio-mii:12 don't have an IRQ mapping
for the internal PHYs anymore, as they've disposed of it in
mv88e6xxx_teardown(). Whereas switch d0032004.mdio-mii:10 has re-created
it, because its code path comes from mv88e6xxx_probe().
Simply put, this change prepares the driver to handle the movement of
mv88e6xxx_mdios_register() to mv88e6xxx_setup() for cross-chip DSA trees.
Also, the code being deleted was partially wrong anyway (in a way which
may have hidden this other issue). mv88e6xxx_g2_irq_mdio_setup()
populates bus->irq[] starting with offset chip->info->phy_base_addr, but
the teardown path doesn't apply that offset too. So it disposes of virq
0 for phy = [ 0, phy_base_addr ).
All switch families have phy_base_addr = 0, except for MV88E6141 and
MV88E6341 which have it as 0x10. I guess those families would have
happened to work by mistake in cross-chip scenarios too.
I'm deleting the body of mv88e6xxx_g2_irq_mdio_free() but leaving its
call sites and prototype in place. This is because, if we ever need to
add back some teardown procedure in the future, it will be perhaps
error-prone to deduce the proper call sites again. Whereas like this,
no extra code should get generated, it shouldn't bother anybody.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There are 3 classes of switch families that the driver is aware of, as
far as mv88e6xxx_change_mtu() is concerned:
- MTU configuration is available per port. Here, the
chip->info->ops->port_set_jumbo_size() method will be present.
- MTU configuration is global to the switch. Here, the
chip->info->ops->set_max_frame_size() method will be present.
- We don't know how to change the MTU. Here, none of the above methods
will be present.
Switch families MV88E6165, MV88E6191, MV88E6220, MV88E6250 and MV88E6290
fall in category 3.
The blamed commit has adjusted the MTU for all 3 categories by EDSA_HLEN
(8 bytes), resulting in a new maximum MTU of 1492 being reported by the
driver for these switches.
I don't have the hardware to test, but I do have a MV88E6390 switch on
which I can simulate this by commenting out its .port_set_jumbo_size
definition from mv88e6390_ops. The result is this set of messages at
probe time:
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 1
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 2
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 3
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 4
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 5
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 6
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 7
mv88e6085 d0032004.mdio-mii:10: nonfatal error -34 setting MTU to 1500 on port 8
It is highly implausible that there exist Ethernet switches which don't
support the standard MTU of 1500 octets, and this is what the DSA
framework says as well - the error comes from dsa_slave_create() ->
dsa_slave_change_mtu(slave_dev, ETH_DATA_LEN).
But the error messages are alarming, and it would be good to suppress
them.
As a consequence of this unlikeliness, we reimplement mv88e6xxx_get_max_mtu()
and mv88e6xxx_change_mtu() on switches from the 3rd category as follows:
the maximum supported MTU is 1500, and any request to set the MTU to a
value larger than that fails in dev_validate_mtu().
Fixes: b9c587fed6 ("dsa: mv88e6xxx: Include tagger overhead when setting MTU for DSA and CPU ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch receives management traffic such as STP and LLDP. However, PTP
messages are not received, only transmitted.
Ideally, the switch would trap all PTP messages to the management CPU. This
particular switch has a PTP block which identifies PTP messages and traps them
to a dedicated port. There is a register to program this destination. This is
not used at the moment.
Therefore, program it to the same port as the MGMT traffic is trapped to. This
allows to receive PTP messages as soon as timestamping is enabled.
In addition, the datasheet mentions that this register is not valid e.g., for
6190 variants. So, add a new PTP operation which is added for the 6390 and 6290
devices.
Tested simply like this on Marvell 88E6390, revision 1:
|/ # ptp4l -2 -i lan4 --tx_timestamp_timeout=40 -m
|[...]
|ptp4l[147.450]: master offset 56 s2 freq +1262 path delay 413
|ptp4l[148.450]: master offset 22 s2 freq +1244 path delay 434
|ptp4l[149.450]: master offset 5 s2 freq +1234 path delay 446
|ptp4l[150.451]: master offset 3 s2 freq +1233 path delay 451
|ptp4l[151.451]: master offset 1 s2 freq +1232 path delay 451
|ptp4l[152.451]: master offset -3 s2 freq +1229 path delay 451
|ptp4l[153.451]: master offset 9 s2 freq +1240 path delay 451
Link: https://lore.kernel.org/r/CAFSKS=PJBpvtRJxrR4sG1hyxpnUnQpiHg4SrUNzAhkWnyt9ivg@mail.gmail.com
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The global2 SMI MDIO bus driver can perform both C22 and C45
transfers. Create separate functions for each and register the C45
versions using the new API calls where appropriate. Update the SERDES
code to make use of these new accessors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This implementation for the Marvell mv88e6xxx chip series is based on
handling ATU miss violations occurring when packets ingress on a port
that is locked with learning on. This will trigger a
SWITCHDEV_FDB_ADD_TO_BRIDGE event, which will result in the bridge module
adding a locked FDB entry. This bridge FDB entry will not age out as
it has the extern_learn flag set.
Userspace daemons can listen to these events and either accept or deny
access for the host, by either replacing the locked FDB entry with a
simple entry or leave the locked entry.
If the host MAC address is already present on another port, a ATU
member violation will occur, but to no real effect, and the packet will
be dropped in hardware. Statistics on these violations can be shown with
the command and example output of interest:
ethtool -S ethX
NIC statistics:
...
atu_member_violation: 5
atu_miss_violation: 23
...
Where ethX is the interface of the MAB enabled port.
Furthermore, as added vlan interfaces where the vid is not added to the
VTU will cause ATU miss violations reporting the FID as
MV88E6XXX_FID_STANDALONE, we need to check and skip the miss violations
handling in this case.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As only the hardware access functions up til and including
mv88e6xxx_g1_atu_mac_read() called under the interrupt handler
need to take the chip lock, we release the chip lock after this call.
The follow up code that handles the violations can run without the
chip lock held.
In further patches, the violation handler function will even be
incompatible with having the chip lock held. This due to an AB/BA
ordering inversion with rtnl_lock().
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The default return value -EOPNOTSUPP of mv88e6xxx_port_bridge_flags()
came from the return value of the DSA method port_egress_floods() in
commit 4f85901f00 ("net: dsa: mv88e6xxx: add support for bridge flags"),
but the DSA API was changed in commit a8b659e7ff ("net: dsa: act as
passthrough for bridge port flags"), resulting in the return value
-EOPNOTSUPP not being valid anymore, and sections for new flags will not
need to set the return value to zero on success, as with the new mab flag
added in a following patch.
Signed-off-by: Hans J. Schultz <netdev@kapio-technology.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Florian Fainelli
Su Hui
Jakub Kicinski
Fabio Estevam
Colin Ian King
Alfred Lee
Ante Knezic
Rob Herring
Russell King (Oracle)
Linus Walleij
Michal Smulski
Andreas Svensson
Lukasz Majewski
Matthias Schiffer
Alexis Lothoré
Marco Migliore
Angelo Dureghello
Andrew Lunn
Gustav Ekelund
Steffen Bätz
Marek Behún
Klaus Kudielka
Vladimir Oltean
Kurt Kanzenbach
Hans J. Schultz