Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI xHC host should be stopped and xhci driver memory freed before putting
host to PCI D3 state during PCI remove callback.
Hosts with XHCI_SPURIOUS_WAKEUP quirk did this the wrong way around
and set the host to D3 before calling usb_hcd_pci_remove(dev), which will
access the host to stop it, and then free xhci.
Fixes: f1f6d9a8b5 ("xhci: don't dereference a xhci member after removing xhci")
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HCD does not allocate or request interrupt for the xhci driver, but HCD
does free and sync xhci interrupts in some cases. Add comment detailing
in which cases HCD will free/sync xhci interrupts.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'sbrn' is used to store the Serial Bus Release Number, which is
then only used for a debug message. Thus, 'sbrn' can be a local variable
and assigned after the primary HCD check. The SBRN debug message is only
printed when a primary HCD is setup.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240905143300.1959279-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_USB_XHCI_PCI_RENESAS is enabled, xhci-pci conditionally
calls into the xhci-pci-renesas module, which means both modules must
be loaded to use any xHCI PCI controller.
The MODULE_FIRMWARE declaration in the base xhci-pci module causes
initramfs-tools to check for and warn about missing firmware for the
Renesas xHCI controllers, when any xHCI PCI controller is present.
And because of the previous oddity, simply moving this declaration to
xhci-pci-renesas wouldn't help.
To fix this, reverse the relationship between the modules:
- Remove the quirk for the Renesas xHCIs, and the driver_data
structure used only for them
- In xhci-pci:
- Rename xhci_pci_probe() to xhci_pci_common_probe()
- Export xhci_pci_common_probe() and xhci_pci_remove()
- Use a new probe function that rejects the Renesas xHCIs and then
calls the common probe function
- In xhci-pci-renesas:
- Stop exporting renesas_xhci_check_request_fw()
- Add a probe function that calls renesas_xhci_check_request_fw()
followed by xhci_pci_common_probe()
- Add and register a new pci_driver matching only the Renesas xHCIs
and using its own probe function, but with other operations the
same as in xhci-pci
- Make CONFIG_USB_XHCI_PCI_RENESAS depend on CONFIG_USB_XHCI_PCI,
not the other way around
Finally, move the MODULE_FIRMWARE declaration to xhci-pci-renesas.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Cyril Brulebois <cyril@debamax.com>
Link: https://lore.kernel.org/r/ZqqfXYRJf7kGaqus@decadent.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TGL systems have the same issue as ADL, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to TGL as well.
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects TGL devices, and TGL support was added starting from v5.3.
Cc: stable@vger.kernel.org
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240626124835.1023046-21-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in commit 8f873c1ff4 ("xhci: Blacklist using streams on the
Etron EJ168 controller"), EJ188 have the same issue as EJ168, where Streams
do not work reliable on EJ188. So apply XHCI_BROKEN_STREAMS quirk to EJ188
as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in commit c877b3b2ad ("xhci: Add reset on resume quirk for
asrock p67 host"), EJ188 have the same issue as EJ168, where completely
dies on resume. So apply XHCI_RESET_ON_RESUME quirk to EJ188 as well.
Cc: stable@vger.kernel.org
Signed-off-by: Kuangyi Chiang <ki.chiang65@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240611120610.3264502-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's better to keep track on Thunderbolt xHCI IDs in a separate group.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are three out of many Intel platforms that are using TLAs
instead of the full names in the PCI IDs. Modify them accordingly.
This also fixes the logic of grouping as seemed to be by an LSB
byte of the ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.
This is so common that turn it into default behavior.
xhci_warn_ratelimited() is no longer used after this, so remove it.
A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.
See xhci 1.2 spec 4.9.1 Transfer Descriptors
"Note: If an error is detected while processing a multi-TRB TD, the xHC
shall generate a Transfer Event for the TRB that the error was detected
on with the appropriate error Condition Code, then may advance to the
next TD. If in the process of advancing to the next TD, a Transfer TRB
is encountered with its IOC flag set, then the Condition Code of the
Transfer Event generated for that Transfer TRB should be Success,
because there was no error actually associated with the TRB that
generated the Event. However, an xHC implementation may redundantly
assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Slot ID is a index of a virtual device in struct 'xhci_hcd->devs[]'.
Previously, to get the slot ID associated with a port, we had to loop
through all devices and compare ports, which is very inefficient.
Instead, the slot ID (of the device which is directly connected to the
port), is added to the its corresponding 'xhci_port' struct. As a result,
finding the port's device is quick and easy.
Function 'xhci_find_slot_id_by_port()' is removed, as it is no longer
needed.
Signed-off-by: Niklas Neronin <niklas.neronin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240229141438.619372-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4baf121815.
Enabling runtime pm as default for all AMD xHC 1.1 controllers caused
regression. An initial attempt to fix those was done in commit a5d6264b63
("xhci: Enable RPM on controllers that support low-power states") but new
issues are still seen.
Revert this to get those AMD xHC 1.1 systems working
This patch went to stable an needs to be reverted from there as well.
Fixes: 4baf121815 ("xhci: Loosen RPM as default policy to cover for AMD xHC 1.1")
Link: https://lore.kernel.org/linux-usb/55c50bf5-bffb-454e-906e-4408c591cb63@molgen.mpg.de
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20231205090548.1377667-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove extra spaces/indentation and add spaces where required.
This commit does not change any functionality.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify 'xhci_try_enable_msi()' and reduce unnecessary function calls.
xHCI driver first tries to allocate 'num_online_cpu()' number of MSI-X
vectors, if that fails it falls back to a single MSI vector. There is no
good reason for this, we currently only support a primary interrupter.
However, we are still interested in knowing if there are more vectors
available, which will be utilized once we get secondary interrupter
support.
Call 'pci_alloc_irq_vectors()' once (with MSI-X and MSI flag), instead
of separately for MSI-X and MSI. And accept any number of MSI-X or MSI
vectors between 1 and 'num_online_cpu()'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of variable 'msix_count' containing the number of MSI-X vectors,
now it can contains MSI or MSI-X vector amount. Because both interrupt
methods allow several vectors. Thus, 'msix_count' is renamed to 'nvecs'.
Additionally, instead of storing the maximum possible vector amount,
now it stores the amount of successfully allocated vectors, or negative
integer on allocation failure.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current way the xhci driver sets up MSI interrupts is overly complex
and messy. The whole MSI setup can be done in one simple function.
Continue refactoring MSI/MSI-X setup by incorporating 'xhci_setup_msi()'
into 'xhci_try_enable_msi()'. Now all interrupt enabling is contained in
one function, which should make it easier to rework.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current way the xhci driver sets up MSI/MSI-X interrupts is overly
complex and messy. The whole MSI/MSI-X setup can be done in one simple
function.
Start refactoring this by incorporating 'xhci_setup_msix()' into
'xhci_try_enable_msi()'. 'xhci_setup_msix()' is a static function which
is only called by 'xhci_try_enable_msi()'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current xHCI driver only supports one "interrupter", meaning we will
only use one MSI/MSI-X interrupt line. Thus, add handler only to the
first interrupt line.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Co-developed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the error check "No MSI-X/MSI found and no IRQ in BIOS" inside
'goto legacy'. It is better to check if the IRQ interrupt is available,
before trying to add a handler. Additionally the aforementioned error
message is much more clear.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the low-power states of the underlying platform to enable runtime PM.
If the platform doesn't support runtime D3, then enabling default RPM will
result in the controller malfunctioning, as in the case of hotplug devices
not being detected because of a failed interrupt generation.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD USB host controller (1022:43f7) isn't going into PCI D3 by default
without anything connected. This is because the policy that was introduced
by commit a611bf473d ("xhci-pci: Set runtime PM as default policy on all
xHC 1.2 or later devices") only covered 1.2 or later.
The 1.1 specification also has the same requirement as the 1.2
specification for D3 support. So expand the runtime PM as default policy
to all AMD 1.1 devices as well.
Fixes: a611bf473d ("xhci-pci: Set runtime PM as default policy on all xHC 1.2 or later devices")
Link: https://composter.com.ua/documents/xHCI_Specification_for_USB.pdf
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add U1/U2 feature support of xHCI for ZHAOXIN.
Since both INTEL and ZHAOXIN need to check the tier where the device is
located to determine whether to enabled U1/U2, remove the previous INTEL
U1/U2 tier policy and add common policy in xhci_check_tier_policy.
If vendor has specific U1/U2 enable policy,quirks can be add to declare.
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-12-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ZHAOXIN xHCI controllers follow usb3.1 spec, but only support
gen1 speed 5Gbps. While in Linux kernel, if xHCI suspport usb3.1,
root hub speed will show on 10Gbps.
To fix this issue of ZHAOXIN xHCI platforms, read usb speed ID
supported by xHCI to determine root hub speed. And add a quirk
XHCI_ZHAOXIN_HOST for this issue.
[fix warning about uninitialized symbol -Mathias]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-11-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some ZHAOXIN hosts, xHCI will prefetch TRB for performance
improvement. However this TRB prefetch mechanism may cross page boundary,
which may access memory not allocated by xHCI driver. In order to fix
this issue, two pages was allocated for a segment and only the first
page will be used. And add a quirk XHCI_ZHAOXIN_TRB_FETCH for this issue.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-10-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ZHAOXIN ZX-100 project, xHCI can't work normally after resume
from system Sx state. To fix this issue, when resume from system
Sx state, reinitialize xHCI instead of restore.
So, Add XHCI_RESET_ON_RESUME quirk for ZX-100 to fix issue of
resuming from system Sx state.
Cc: stable@vger.kernel.org
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-9-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XHCI_PLAT quirk was only needed to ensure non-PCI xHC host avoided
setting up MSI interrupts in generic xhci codepaths.
The MSI setup code is now moved to PCI specific xhci-pci.c file so
the quirk is no longer needed.
Remove setting the XHCI_PLAT quirk for HiSilocon SoC xHC, NVIDIA Tegra xHC,
MediaTek xHC, the generic xhci-plat driver, and the checks for XHCI_PLAT
in xhci-pci.c MSI setup code.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-5-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here and this resolves merge conflicts in:
drivers/usb/dwc3/gadget.c
drivers/usb/gadget/udc/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Donghun reports that a notebook that has an AMD Ryzen 5700U but supports
S3 has problems with USB after resuming from suspend. The issue was
bisected down to commit d1658268e4 ("usb: pci-quirks: disable D3cold on
xhci suspend for s2idle on AMD Renoir").
As this issue only happens on S3, narrow the broken D3cold quirk to only
run in s2idle.
Fixes: d1658268e4 ("usb: pci-quirks: disable D3cold on xhci suspend for s2idle on AMD Renoir")
Reported-and-tested-by: Donghun Yoon <donghun.yoon@lge.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230515134059.161110-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the pci_resume method has only a flag indicating whether the
system is resuming from hibernation. In order to handle all PM events like
AUTO_RESUME (runtime resume from device in D3), RESUME (system resume from
s2idle, S3 or S4 states) etc change the pci_resume method to handle all PM
events.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230428140056.1318981-2-Basavaraj.Natikar@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB fixes in here for testing, and this resolves two merge
conflicts, one pointed out by linux-next:
drivers/usb/dwc3/dwc3-pci.c
drivers/usb/host/xhci-pci.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 4c2604a9a6.
Asynch probe caused regression in a setup with both Renesas and Intel xHC
controllers. Devices connected to the Renesas disconnected shortly after
boot. With Asynch probe the busnumbers got interleaved.
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 2
xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 4
Reason why this commit causes regression is still unknown, but revert it
while debugging the issue.
Fixes: 4c2604a9a6 ("usb: xhci-pci: Set PROBE_PREFER_ASYNCHRONOUS")
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/linux-usb/20230307132120.5897c5af@deangelis.fenrir.org.uk
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230330143056.1390020-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent patch caused an unused-function warning in builds with
CONFIG_PM disabled, after the function became marked 'static':
drivers/usb/host/xhci-pci.c:91:13: error: 'xhci_msix_sync_irqs' defined but not used [-Werror=unused-function]
91 | static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
| ^~~~~~~~~~~~~~~~~~~
This could be solved by adding another #ifdef, but as there is
a trend towards removing CONFIG_PM checks in favor of helper
macros, do the same conversion here and use pm_ptr() to get
either a function pointer or NULL but avoid the warning.
As the hidden functions reference some other symbols, make
sure those are visible at compile time, at the minimal cost of
a few extra bytes for 'struct usb_device'.
Fixes: 9abe15d55d ("xhci: Move xhci MSI sync function to to xhci-pci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230328131114.1296430-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move function to sync MSI from xhci.c to xhci-pci.c to decouple PCI
specific code from generic xhci code.
No functional changes, function is an exact copy
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call function to sync MSI interrupts from pci specific xhci_pci_suspend()
function in xhci-pci.c instead of from generic xhci_suspend()
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move function to cleanup MSI from xhci.c to xhci-pci.c
This is to decouple PCI specific code from generic xhci code.
No functional changes, function is an exact copy
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Call the PCI specific MSI/MSIX interrupt freeing code from the xhci-pci
callbacks instead of generic xhci code, decoupling PCI parts from
generic xhci functions.
Adds xhci_pci_stop() that overrides xhci_stop() for PCI xHC controllers.
This will free MSIX interrupts a bit later in the hc_driver stop
callback, but is still earlier than usb core frees "legacy" interrupts,
or interrupts for other hosts.
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move functions to setup msi from xhci.c to xhci-pci.c to decouple
PCI specific code from generic xhci code.
No functional changes, functions are an exact copy
[commit message rewording -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci MSI setup is currently done at the same time as xHC host is started
in xhci_run(). This couples the generic xhci code with PCI, and will
reconfigure MSI/MSIX interrupts every time xHC is started.
Decouple MSI/MSIX configuration from generic xhci code by moving MSI/MSIX
part to a PCI specific xhci_pci_run() function overriding xhci_run().
This allows us to remove unnecessay MSI/MSIX reconfiguration done every
time PCI xhci resumes from suspend. i.e. remove the xhci_cleanup_msix()
call from xhci_resume() and the xhci_try_enale_msi() call in xhci_run()
called a bit later by xhci_resume()
[minor changes and commit message rewrite -Mathias]
Signed-off-by: Josue David Hernandez Gutierrez <josue.d.hernandez.gutierrez@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230317154715.535523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB3 ports on xHC hosts may have retimers that cause too long
exit latency to work with native USB3 U1/U2 link power management states.
For now only use usb_acpi_port_lpm_incapable() to evaluate if port lpm
should be disabled while setting up the USB3 roothub.
Other ways to identify lpm incapable ports can be added here later if
ACPI _DSM does not exist.
Limit this to Intel hosts for now, this is to my knowledge only
an Intel issue.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow PCI hosts to check and tune roothub and port settings
before the hub is up and running.
This override is needed to turn off U1 and U2 LPM for some ports
based on per port ACPI _DSM, _UPC, or possibly vendor specific mmio
values for Intel xHC hosts.
Usb core calls the host update_hub_device once it creates a hub.
Entering U1 or U2 link power save state on ports with this limitation
will cause link to fail, turning the usb device unusable in that setup.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230116142216.1141605-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable U3 suspended ports in hibernate S4 poweroff_late for systems
with XHCI_RESET_TO_DEFAULT quirk, if wakeup is not enabled.
This reduces the number of self-powered usb devices from surviving in
U3 suspended state into next reboot.
Bootloader/firmware on these systems can't handle usb ports in U3, and
will timeout, causing extra delay during reboot/restore from S4.
Add pci_poweroff_late() callback to struct usb_hcd to get this done at
the correct stage in hibernate.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ADL-N systems have the same issue as ADL-P, where a large boot firmware
delay is seen if USB ports are left in U3 at shutdown. So apply the
XHCI_RESET_TO_DEFAULT quirk to ADL-N as well.
This patch depends on commit 34cd2db408 ("xhci: Add quirk to reset
host back to default state at shutdown").
The issue it fixes is a ~20s boot time delay when booting from S5. It
affects ADL-N devices, and ADL-N support was added starting from v5.16.
Cc: stable@vger.kernel.org
Signed-off-by: Reka Norman <rekanorman@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20221130091944.2171610-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pawel Laszczak
WangYuli
Mathias Nyman
Niklas Neronin
Ben Hutchings
Reka Norman
Kuangyi Chiang
Andy Shevchenko
Basavaraj Natikar
Niklas Neronin
Greg Kroah-Hartman
Oliver Neukum
Weitao Wang
Mario Limonciello
Arnd Bergmann
Josue David Hernandez Gutierrez
Ricardo Ribalda