- Add a struct pci_ops.assert_perst() function pointer to assert/deassert
PCIe PERST# and implement it for the qcom driver (Krishna Chaitanya
Chundru)
- Add DT binding and pwrctrl driver for the Toshiba TC9563 PCIe switch,
which must be held in reset after poweron so the pwrctrl driver can
configure the switch via I2C before bringing up the links (Krishna
Chaitanya Chundru)
* pci/pwrctrl-tc9563:
PCI: pwrctrl: Add power control driver for TC9563
PCI: qcom: Implement .assert_perst()
PCI: dwc: Implement .assert_perst() for dwc glue drivers
PCI: Add .assert_perst() to control PCIe PERST#
dt-bindings: PCI: Add binding for Toshiba TC9563 PCIe switch
Add register and bitfield definitions:
- GEN3_RELATED_OFF_EQ_PHASE_2_3 field of GEN3_RELATED_OFF
- Coherency control registers
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20251121164920.2008569-3-vincent.guittot@linaro.org
L1 PM Substates require the CLKREQ# signal and may also require
device-specific support. If CLKREQ# is not supported or driver support is
lacking, enabling L1.1 or L1.2 may cause errors when accessing devices,
e.g.,
nvme nvme0: controller is down; will reset: CSTS=0xffffffff, PCI_STATUS=0x10
If the kernel is built with CONFIG_PCIEASPM_POWER_SUPERSAVE=y or users
enable L1.x via sysfs, users may trip over these errors even if L1
Substates haven't been enabled by firmware or the driver.
To prevent such errors, disable advertising the L1 PM Substates unless the
driver sets "dw_pcie.l1ss_support" to indicate that it knows CLKREQ# is
present and any device-specific configuration has been done.
Set "dw_pcie.l1ss_support" in tegra194 (if DT includes the
"supports-clkreq' property) and qcom (for cfg_2_7_0, cfg_1_9_0, cfg_1_34_0,
and cfg_sc8280xp controllers) so they can continue to use L1 Substates.
Based on Niklas's patch:
https://patch.msgid.link/20251017163252.598812-2-cassel@kernel.org
[bhelgaas: drop hiding for endpoints]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251118214312.2598220-2-helgaas@kernel.org
As per DesignWare Cores PCI Express Controller Databook, section 5.50,
SII: Debug Signals, cxpl_debug_info[63:0]:
[5:0] smlh_ltssm_state: LTSSM current state. Encoding is same as the
dedicated smlh_ltssm_state output.
The mask should be 6 bits, from 0 to 5. Hence, fix the mask definition.
Fixes: 23fe5bd4be ("PCI: keystone: Cleanup ks_pcie_link_up()")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[mani: reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1763122140-203068-1-git-send-email-shawn.lin@rock-chips.com
- Select PCI Power Control Slot driver so slot voltage rails can be turned
on/off if described in Root Port device tree node (Qiang Yu)
- Parse only PCI bridge child nodes in device tree, skipping unrelated
nodes such as OPP (Operating Performance Points), which caused probe
failures (Krishna Chaitanya Chundru)
- Add 8.0 GT/s and 32.0 GT/s equalization settings (Ziyue Zhang)
- Fix typo in CURSOR macro names (Ziyue Zhang)
- Consolidate Root Port 'phy' and 'reset' properties in struct
qcom_pcie_port, regardless of whether we got them from the Root Port node
or the host bridge node (Manivannan Sadhasivam)
- Fetch and map the ELBI register space in the DWC core rather than in each
driver individually (Krishna Chaitanya Chundru)
- Enable ECAM mechanism in DWC core by setting up iATU with 'CFG Shift
Feature' and use this in the qcom driver (Krishna Chaitanya Chundru)
* pci/controller/qcom:
PCI: dwc: Support ECAM mechanism by enabling iATU 'CFG Shift Feature'
PCI: qcom: Prepare for the DWC ECAM enablement
PCI: dwc: Prepare the driver for enabling ECAM mechanism using iATU 'CFG Shift Feature'
PCI: dwc: Add support for ELBI resource mapping
PCI: qcom: Move host bridge 'phy' and 'reset' pointers to struct qcom_pcie_port
PCI: qcom: Fix macro typo for CURSOR
PCI: qcom: Add equalization settings for 8.0 GT/s and 32.0 GT/s
PCI: qcom: Restrict port parsing only to PCIe bridge child nodes
PCI: qcom: Select PCI Power Control Slot driver
Designware databook r5.20a, sec 3.10.10.3 documents the 'CFG Shift Feature'
of the internal Address Translation Unit (iATU). When this feature is
enabled, it shifts/maps the BDF contained in the bits [27:12] of the target
address in MEM TLP to become BDF of the CFG TLP. This essentially
implements the Enhanced Configuration Address Mapping (ECAM) mechanism as
defined in PCIe r6.0, sec 7.2.2.
Currently, the driver is not making use of this CFG shift feature, thereby
creating the iATU outbound map for each config access to the devices,
causing latency and wasting CPU cycles.
So to avoid this, configure the controller to enable CFG shift feature by
enabling the 'CFG Shift' bit of the 'iATU Control 2 Register'.
As a result of enabling CFG shift (ECAM), there is no longer a need to map
the DBI register space separately as the DBI region falls under the
'config' space used for ECAM (as DBI is used to access the Root Port).
For enabling ECAM using CFG shift, the platform has to satisfy following
requirements:
1. Size of the 'config' memory space to be used as ECAM memory should be
able to accommodate the number of buses defined in the 'bus-range'
property of the host bridge DT node.
2. The 'config' memory space should be 256 MiB aligned. This requirement
comes from PCIe r6.0, sec 7.2.2, which says the base address of ECAM
memory should be aligned to a 2^(n+20) byte address boundary. For the
DWC cores, n is 8, so this results in 2^28 byte alignment requirement.
It should be noted that some DWC vendor glue drivers like pcie-al may use
their own ECAM mechanism. For those controllers, set
'dw_pcie_rp::native_ecam' flag and skip enabling the CFG Shift feature in
the DWC core.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: code split, reworded subject/description, comment, native_ecam flag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-4-e84390ba75fa@kernel.org
In order to enable PCIe ECAM mechanism in DWC driver as per the 'CFG Shift
Feature' documented in Designware databook r5.20a, sec 3.10.10.3, prepare
the driver to handle the one time iATU setup and creating ECAM window.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: splitted the preparatory code into a separate commit for bisectability]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-2-e84390ba75fa@kernel.org
External Local Bus Interface (ELBI) is an optional register space for all
DWC IPs containing the vendor specific registers. There is no need for the
vendor glue drivers to fetch and map the ELBI region separately.
Hence, optionally fetch and map the resource from DT in the DWC core. This
also warrants dropping the corresponding code from glue drivers. Hence,
drop the ELBI resource fetch and map logic from glue drivers and convert
them to use 'dw_pci::elbi_base'.
Note that the pcie-qcom-ep driver used devm_pci_remap_cfg_resource() to map
the ELBI resource previously. But it was a mistake since
devm_pci_remap_cfg_resource() should only be used for mapping the PCIe
config space region as it maps the region as Non-Posted. As ELBI is used to
hold vendor specific registers, there is no need to map the region as
Non-Posted. With this conversion, the region will get mapped as normal MMIO
memory.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: removed elbi override, converted glue drivers and reworded description]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250923-controller-dwc-ecam-v10-1-e84390ba75fa@kernel.org
Add lane equalization setting for 8.0 GT/s and 32.0 GT/s to enhance link
stability and avoid AER Correctable Errors reported on some platforms
(eg. SA8775P).
8.0 GT/s, 16.0 GT/s and 32.0 GT/s require the same equalization setting.
This setting is programmed into a group of shadow registers, which can be
switched to configure equalization for different speeds by writing 00b,
01b and 10b to `RATE_SHADOW_SEL`.
Hence, program equalization registers in a loop using link speed as index,
so that equalization setting can be programmed for 8.0 GT/s, 16.0 GT/s
and 32.0 GT/s.
Fixes: 489f14be0e ("arm64: dts: qcom: sa8775p: Add pcie0 and pcie1 nodes")
Co-developed-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Signed-off-by: Qiang Yu <qiang.yu@oss.qualcomm.com>
Signed-off-by: Ziyue Zhang <ziyue.zhang@oss.qualcomm.com>
[mani: wrapped the warning to fit 100 columns, used post-increment for loop]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250904065225.1762793-2-ziyue.zhang@oss.qualcomm.com
The PCI core now provides generic PCI_FIND_NEXT_CAP() macros to search for
PCI capabilities, using config accessors we supply.
Use them in the DWC EP driver to implement dw_pcie_ep_find_capability()
instead of duplicating the algorithm.
Signed-off-by: Hans Zhang <18255117159@163.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250819145828.438541-1-18255117159@163.com
The PCI core now provides generic PCI_FIND_NEXT_CAP() and
PCI_FIND_NEXT_EXT_CAP() macros to search for PCI capabilities, using
config accessors we supply.
Use them in the DWC driver to implement dw_pcie_find_capability() and
dw_pcie_find_ext_capability() instead of duplicating the algorithm.
Signed-off-by: Hans Zhang <18255117159@163.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20250813144529.303548-5-18255117159@163.com
- Export DWC MSI controller related APIs for use by upcoming DWC-based ECAM
implementation (Mayank Rana)
- Rename gen_pci_init() to pci_host_common_ecam_create() and export for use
by controller drivers (Mayank Rana)
- Add DT binding and driver support for SA8255p, which supports ECAM for
Configuration Space access (Mayank Rana)
- Update DT binding and driver to describe PHYs and per-Root Port resets in
a Root Port stanza and deprecate describing them in the host bridge; this
makes it possible to support multiple Root Ports in the future (Krishna
Chaitanya Chundru)
* pci/controller/qcom:
PCI: qcom: Add support for parsing the new Root Port binding
dt-bindings: PCI: qcom: Move PHY & reset GPIO to Root Port node
PCI: qcom: Add support for Qualcomm SA8255p based PCIe Root Complex
dt-bindings: PCI: qcom,pcie-sa8255p: Document ECAM compliant PCIe root complex
PCI: host-generic: Rename and export gen_pci_init() for PCIe controller drivers
PCI: dwc: Export DWC MSI controller related APIs
- Rename PCIE_RESET_CONFIG_DEVICE_WAIT_MS to PCIE_RESET_CONFIG_WAIT_MS (the
required delay before sending config requests after a reset) (Niklas
Cassel)
- PCIE_T_RRS_READY_MS and PCIE_RESET_CONFIG_WAIT_MS were two names for the
same delay; replace PCIE_T_RRS_READY_MS with PCIE_RESET_CONFIG_WAIT_MS
and remove PCIE_T_RRS_READY_MS (Niklas Cassel)
- Add required PCIE_RESET_CONFIG_WAIT_MS delay after Link up IRQ to
dw-rockchip, qcom (Niklas Cassel)
- Add required PCIE_RESET_CONFIG_WAIT_MS after waiting for Link up on
Ports that support > 5.0 GT/s in dwc core (Niklas Cassel)
- Move LINK_WAIT_SLEEP_MS and LINK_WAIT_MAX_RETRIES to pci.h and prefix
with 'PCIE_' for potential sharing across drivers (Niklas Cassel)
* pci/controller/linkup-fix:
PCI: Move link up wait time and max retries macros to pci.h
PCI: dwc: Ensure that dw_pcie_wait_for_link() waits 100 ms after link up
PCI: qcom: Wait PCIE_RESET_CONFIG_WAIT_MS after link-up IRQ
PCI: dw-rockchip: Wait PCIE_RESET_CONFIG_WAIT_MS after link-up IRQ
PCI: rockchip-host: Use macro PCIE_RESET_CONFIG_WAIT_MS
PCI: Rename PCIE_RESET_CONFIG_DEVICE_WAIT_MS to PCIE_RESET_CONFIG_WAIT_MS
Switch to msi_create_parent_irq_domain() from pci_msi_create_irq_domain()
which was using legacy MSI domain setup.
Signed-off-by: Nam Cao <namcao@linutronix.de>
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: rebase on dev_fwnode() conversion]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://patch.msgid.link/04d4a96046490e50139826c16423954e033cdf89.1750858083.git.namcao@linutronix.de
Export dw_pcie_msi_host_init(), dw_pcie_msi_init(), and dw_pcie_free_msi()
APIs to allow them to be reused by the upcoming DWC based ECAM driver
implementation. Also, move MSI IRQ related initialization code to
dw_pcie_msi_init(), as this code must be executed before dw_pcie_msi_init()
API can be used with ECAM driver.
Signed-off-by: Mayank Rana <mayank.rana@oss.qualcomm.com>
[mani: commit message rewording]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250616224259.3549811-2-mayank.rana@oss.qualcomm.com
Move the LINK_WAIT_SLEEP_MS and LINK_WAIT_MAX_RETRIES macros to pci.h.
Prefix the macros with PCIE_ in order to avoid redefining these for
drivers that already have macros named like this.
No functional changes.
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://patch.msgid.link/20250625102347.1205584-15-cassel@kernel.org
- Add OF support for parsing DT 'eq-presets-<N>gts' property for lane
equalization presets (Krishna Chaitanya Chundru)
- Read Maximum Link Width from the Link Capabilities register if DT lacks
'num-lanes' property (Krishna Chaitanya Chundru)
- Add Physical Layer 64 GT/s Capability ID and register offsets for 8, 32,
and 64 GT/s lane equalization registers (Krishna Chaitanya Chundru)
- Add generic dwc support for configuring lane equalization presets
(Krishna Chaitanya Chundru)
- Add DT and driver support for PCIe on IPQ5018 SoC (Nitheesh Sekar)
* pci/controller/qcom:
PCI: qcom: Add support for IPQ5018
dt-bindings: PCI: qcom: Add IPQ5018 SoC
PCI: dwc: Add support for configuring lane equalization presets
PCI: Add lane equalization register offsets
PCI: dwc: Update pci->num_lanes to maximum supported link width
PCI: of: Add of_pci_get_equalization_presets() API
Synopsys Designware PCIe IPs support PTM capability as defined in the PCIe
spec r6.0, sec 6.21. The PTM context information is exposed through Vendor
Specific Extended Capability (VSEC) registers on supported controller
implementation.
Hence, add support for exposing these context information to userspace
through the debugfs interface for the DWC controllers (both RC and EP).
Currently, only Qcom controllers are supported. For adding support for
other DWC vendor controllers, dwc_pcie_ptm_vsec_ids[] needs to be extended.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-3-02d26d51400b@linaro.org
Upcoming PTM debugfs interface relies on the DWC PCIe mode to expose the
relevant debugfs attributes to userspace. So pass the mode to
dwc_pcie_debugfs_init() API from host and ep drivers and save it in
'struct dw_pcie::mode'.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://patch.msgid.link/20250505-pcie-ptm-v4-2-02d26d51400b@linaro.org
PCIe link status check is supposed to return a boolean to indicate whether
the link is up or not. So, modify the link_up callbacks and
dw_pcie_link_up() function to return bool instead of int.
Signed-off-by: Hans Zhang <18255117159@163.com>
[mani: commit message reword]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Link: https://patch.msgid.link/20250510160710.392122-2-18255117159@163.com
PCIe equalization presets are predefined settings used to optimize signal
integrity by compensating for signal loss and distortion in high-speed data
transmission.
Based upon the number of lanes and the data rate supported, write the
preset data read from the device tree in to the lane equalization control
registers. These preset values will be used by the controller during the
LTSSM lane equalization procedure.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: reworded the commit message and comments in the driver]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250328-preset_v6-v9-5-22cfa0490518@oss.qualcomm.com
If the num-lanes property is not present in the devicetree, update
pci->num_lanes with the hardware supported maximum link width using
the newly introduced dw_pcie_link_get_max_link_width() API.
The API is used to get the Maximum Link Width (MLW) of the controller.
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
[mani: reworded commit message a bit]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250328-preset_v6-v9-3-22cfa0490518@oss.qualcomm.com
- Ioremap() msg_res region using res->start (the CPU address), not the ATU
'cpu_addr', which will be replaced with the ATU input address (which may
not be the CPU address) (Frank Li)
- Rename struct dw_pcie_ob_atu_cfg.cpu_addr to 'parent_bus_addr' (Frank Li)
- Call devm_pci_alloc_host_bridge() early in dw_pcie_host_init() to keep
devicetree-related code together (Frank Li)
- Consolidate devicetree handling in dw_pcie_host_get_resources() (Bjorn
Helgaas)
- Add dw_pcie_parent_bus_offset() to look up the parent bus address of a
specified 'reg' property and return the offset from the CPU physical
address (Frank Li)
- Add cross-checking with .cpu_addr_fixup() and debug logging to
dw_pcie_parent_bus_offset() (Frank Li)
- Use devicetree 'reg[config]' via dw_pcie_parent_bus_offset() to derive
CPU -> ATU addr offset for host controller (Frank Li)
- Call epc_create() early in dw_pcie_ep_init() to keep devicetree-related
code together (Bjorn Helgaas)
- Consolidate devicetree handling in dw_pcie_ep_get_resources() (Bjorn
Helgaas)
- Use devicetree 'reg[addr_space]' via dw_pcie_parent_bus_offset() to
derive CPU -> ATU addr offset for endpoint controller (Frank Li)
- Update dw_pcie_find_index() to remove assumption that ATU input address
is non-zero (Frank Li)
- Apply struct dw_pcie.parent_bus_offset in ATU users to remove use of
.cpu_addr_fixup() when programming ATU (Frank Li)
- Remove imx_pcie_cpu_addr_fixup() since dwc core can now derive the ATU
input address (using parent_bus_offset) from devicetree (Frank Li)
- Remove intel_pcie_cpu_addr() since dwc core can now derive the ATU input
address (using parent_bus_offset) from devicetree (Frank Li)
* pci/controller/dwc-cpu-addr-fixup:
PCI: intel-gw: Remove intel_pcie_cpu_addr()
PCI: imx6: Remove imx_pcie_cpu_addr_fixup()
PCI: dwc: Use parent_bus_offset to remove need for .cpu_addr_fixup()
PCI: dwc: ep: Ensure proper iteration over outbound map windows
PCI: dwc: ep: Use devicetree 'reg[addr_space]' to derive CPU -> ATU addr offset
PCI: dwc: ep: Consolidate devicetree handling in dw_pcie_ep_get_resources()
PCI: dwc: ep: Call epc_create() early in dw_pcie_ep_init()
PCI: dwc: Use devicetree 'reg[config]' to derive CPU -> ATU addr offset
PCI: dwc: Add dw_pcie_parent_bus_offset() checking and debug
PCI: dwc: Add dw_pcie_parent_bus_offset()
PCI: dwc: Consolidate devicetree handling in dw_pcie_host_get_resources()
PCI: dwc: Call devm_pci_alloc_host_bridge() early in dw_pcie_host_init()
PCI: dwc: Rename cpu_addr to parent_bus_addr for ATU configuration
PCI: dwc: Use resource start as ioremap() input in dw_pcie_pme_turn_off()
# Conflicts:
# drivers/pci/controller/dwc/pcie-designware.c
# drivers/pci/controller/dwc/pcie-designware.h
The 'ranges' property of a PCI controller's parent can indicate address
translation information. Most system use 1:1 map between CPU physical and
PCI controller input addresses.
But some hardware, like i.MX8QXP, doesn't use 1:1 map. See below diagram:
┌─────────┐ ┌────────────┐
┌─────┐ │ │ IA: 0x8ff8_0000 │ │
│ CPU ├───►│ ┌────►├─────────────────┐ │ PCI │
└─────┘ │ │ │ IA: 0x8ff0_0000 │ │ │
CPU Addr │ │ ┌─►├─────────────┐ │ │ Controller │
0x7ff8_0000─┼───┘ │ │ │ │ │ │
│ │ │ │ │ │ │ PCI Addr
0x7ff0_0000─┼──────┘ │ │ └──► IOSpace ─┼────────────►
│ │ │ │ │ 0
0x7000_0000─┼────────►├─────────┐ │ │ │
└─────────┘ │ └──────► CfgSpace ─┼────────────►
Bus Fabric │ │ │ 0
│ │ │
└──────────► MemSpace ─┼────────────►
IA: 0x8000_0000 │ │ 0x8000_0000
└────────────┘
bus@5f000000 {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x80000000 0x0 0x70000000 0x10000000>;
pcie@5f010000 {
compatible = "fsl,imx8q-pcie";
reg = <0x5f010000 0x10000>, <0x8ff00000 0x80000>;
reg-names = "dbi", "config";
...
};
};
Intermediate address (IA) here means the PCIe controller input address.
The pcie@5f010000 'reg[config]' address is the parent bus (PCIe controller
input) address of CfgSpace.
The ATU in MemSpace is not explicitly described via devicetree, so we
assume the offset from CPU address to intermediate MemSpace address is the
same as that for CfgSpace.
We could use bus@5f000000 'ranges' for the same purpose.
Set parent_bus_offset using dw_pcie_init_parent_bus_offset(). The
parent_bus_offset is not used yet, so no functional change intended.
Link: https://lore.kernel.org/r/20250315201548.858189-8-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
dw_pcie_parent_bus_offset() looks up the parent bus address of a PCI
controller 'reg' property in devicetree. If implemented, .cpu_addr_fixup()
is a hard-coded way to get the parent bus address corresponding to a CPU
physical address.
Add debug code to compare the address from .cpu_addr_fixup() with the
address from devicetree. If they match, warn that .cpu_addr_fixup() is
redundant and should be removed; if they differ, warn that something is
wrong with the devicetree.
If .cpu_addr_fixup() is not implemented, the parent bus address should be
identical to the CPU physical address because we previously ignored the
parent bus address from devicetree. If the devicetree has a different
parent bus address, warn about it being broken.
[bhelgaas: split debug to separate patch for easier future revert, commit
log]
Link: https://lore.kernel.org/r/20250315201548.858189-7-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
[bhelgaas: squash Ioana Ciornei <ioana.ciornei@nxp.com> fix for NULL
pointer deref when driver doesn't supply dw_pcie_ops, e.g., layerscape-pcie
https://lore.kernel.org/r/20250319134339.3114817-1-ioana.ciornei@nxp.com]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Return the offset from CPU physical address to the parent bus address of
the specified element of the devicetree 'reg' property.
[bhelgaas: cpu_phy_addr -> cpu_phys_addr, return offset, split
.cpu_addr_fixup() checking and debug to separate patch]
Link: https://lore.kernel.org/r/20250315201548.858189-6-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename 'cpu_addr' to 'parent_bus_addr' in the DesignWare ATU configuration.
The ATU translates parent bus addresses to PCI addresses, which are often
the same as CPU addresses but can differ in systems where the bus fabric
translates addresses before passing them to the PCIe controller. This
renaming clarifies the purpose and avoids confusion.
Link: https://lore.kernel.org/r/20250315201548.858189-3-helgaas@kernel.org
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add dw_pcie_ep_hide_ext_capability() which can be used by an endpoint
controller driver to hide a capability.
This can be useful to hide a capability that is buggy, such that the
host side does not try to enable the buggy capability.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Link: https://lore.kernel.org/r/20250310094826.842681-5-cassel@kernel.org
Add the debugfs property to provide a view of the current link's LTSSM
status from the Root Port device.
Signed-off-by: Hans Zhang <18255117159@163.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Niklas Cassel <cassel@kernel.org>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250223141848.231232-1-18255117159@163.com
[kwilczynski: commit log, refactor dw_ltssm_sts_string() to avoid
compilation errors on platforms that do not set CONFIG_PCIE_DW_HOST]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Add support to provide Silicon Debug interface to userspace.
This set of debug registers are part of the RAS DES feature present in
DesignWare PCIe controllers.
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Tested-by: Hrishikesh Deleep <hrishikesh.d@samsung.com>
Link: https://lore.kernel.org/r/20250221131548.59616-4-shradha.t@samsung.com
[kwilczynski: commit log, tidy up Kconfig and drop "default y", tidy up
code comments, squashed patch that fixes a NULL pointer dereference when
debugfs is already unavailable during clean-up from
https://lore.kernel.org/linux-pci/20250225171239.19574-2-manivannan.sadhasivam@linaro.org,
refactor dwc_pcie_debugfs_init() to not return errors, squashed patch that
changes how lack of the RAS DES capability is handled from
https://lore.kernel.org/linux-pci/20250304151814.6xu7cbpwpqrvcad5@thinkpad]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
- Fix potential string truncation in dw_pcie_edma_irq_verify() (Niklas
Cassel)
- Don't wait for link up in DWC core if driver can detect Link Up event
(Krishna chaitanya chundru)
- If qcom 'global' IRQ is supported for detection of Link Up events, tell
DWC core not to wait for link up (Krishna chaitanya chundru)
- Update ICC and OPP votes after Link Up events (Krishna chaitanya chundru)
- Use dw-rockchip dll_link_up IRQ to detect Link Up and enumerate devices
so users don't have to manually rescan (Niklas Cassel)
- In dw-rockchip, the 'sys' interrupt is required and detects Link Up
events, so tell DWC core not to wait for link up (Niklas Cassel)
- Always stop link in dw_pcie_suspend_noirq(), which is required at least
for i.MX8QM to re-establish link on resume (Richard Zhu)
- Drop racy and unnecessary LTSSM state check before sending PME_TURN_OFF
message in dw_pcie_suspend_noirq() (Richard Zhu)
- Add stubs for dw_pcie_suspend_noirq() dw_pcie_resume_noirq() when
CONFIG_PCIE_DW_HOST is not defined so drivers don't need #ifdefs (Bjorn
Helgaas)
- Use DWC core suspend/resume functions for imx6 (Frank Li)
- Add imx6 suspend/resume support for i.MX8MQ, i.MX8Q, and i.MX95 (Richard
Zhu)
- Add struct of_pci_range.parent_bus_addr for devices that need their
immediate parent bus address, not the CPU address, e.g., to program an
internal Address Translation Unit (iATU) (Frank Li)
* pci/controller/dwc:
PCI: dwc: Simplify config resource lookup
of: address: Add parent_bus_addr to struct of_pci_range
PCI: imx6: Add i.MX8MQ, i.MX8Q and i.MX95 PM support
PCI: imx6: Use DWC common suspend resume method
PCI: dwc: Add dw_pcie_suspend_noirq(), dw_pcie_resume_noirq() stubs for !CONFIG_PCIE_DW_HOST
PCI: dwc: Remove LTSSM state test in dw_pcie_suspend_noirq()
PCI: dwc: Always stop link in the dw_pcie_suspend_noirq
PCI: dw-rockchip: Don't wait for link since we can detect Link Up
PCI: dw-rockchip: Enumerate endpoints based on dll_link_up IRQ
PCI: qcom: Update ICC and OPP values after Link Up event
PCI: qcom: Don't wait for link if we can detect Link Up
PCI: dwc: Don't wait for link up if driver can detect Link Up event
PCI: dwc: Fix potential truncation in dw_pcie_edma_irq_verify()
# Conflicts:
# drivers/pci/controller/dwc/pci-imx6.c
Previously pcie-designware.h declared dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq() unconditionally, even though they were only
implemented when CONFIG_PCIE_DW_HOST was defined.
Add no-op stubs for them when CONFIG_PCIE_DW_HOST is not defined so
drivers that support both Root Complex and Endpoint modes don't need
Link: https://lore.kernel.org/r/20250117213810.GA656803@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's safe to send PME_TURN_OFF message regardless of whether the link is up
or down, so don't test the LTSSM state before sending the PME_TURN_OFF
message.
Only print an error message when the LTSSM is not in DETECT or POLL. There
shouldn't be an error when no Endpoint is connected at all.
Link: https://lore.kernel.org/r/20241210081557.163555-3-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If the driver can detect the Link Up event and enumerate downstream devices
at that time, we need not wait here.
Skip waiting for link to come up if the driver supports 'use_linkup_irq'.
Link: https://lore.kernel.org/r/20241123-remove_wait2-v5-1-b5f9e6b794c2@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comment, update commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
dw_pcie_prog_ep_inbound_atu() is used to program an inbound iATU in
"BAR Match Mode".
A memory address returned by e.g. kmalloc() is guaranteed to have natural
alignment (aligned to the size of the allocation). It is however not
guaranteed that pci_epc_set_bar() (and thus dw_pcie_prog_ep_inbound_atu())
is supplied an address that has natural alignment. (An EPF driver can send
in an arbitrary physical address to pci_epc_set_bar().)
The DWC Databook description for the LWR_TARGET_RW and LWR_TARGET_HW fields
in the IATU_LWR_TARGET_ADDR_OFF_INBOUND_i registers state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
Add a check to ensure that the physical address programmed in the iATU is
aligned to the size of the BAR (BAR_MASK+1), as without this, we can get
hard to debug errors, as we could write to bits that are read-only (without
getting a write error), which could cause the iATU to end up redirecting to
a physical address that is different from the address that we intended.
Link: https://lore.kernel.org/r/20241213143301.4158431-11-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add RX lane margining settings for 16.0 GT/s (GEN 4) data rate.
These settings improve link stability while operating at high date
rates and helps to improve signal quality.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-4-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
During high data transmission rates such as 16.0 GT/s, there is an
increased risk of signal loss due to poor channel quality and
interference. This can impact receiver's ability to capture signals
accurately.
Hence, as signal compensation is achieved through appropriate lane
equalization, apply lane equalization settings at both transmitter
and receiver which results in an increase in the PCIe signal strength.
While at it, modify the pcie-tegra194 driver to make use of the
common GEN3_EQ_CONTROL_OFF definitions in pcie-designware.h.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-3-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
[mani: dropped the code refactoring and minor changes]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 'link_gen' field is now holding the maximum supported link speed set
either by the controller driver or by DT through 'max-link-speed'
property.
However, the name 'link_gen' sounds like the negotiated link speed of
the PCIe link.
So rename it to 'max_link_speed' to make it clear that it holds the
maximum supported link speed of the controller.
Link: https://lore.kernel.org/linux-pci/20240911-pci-qcom-gen4-stability-v7-1-743f5c1fd027@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
PARF hardware block which is a wrapper on top of DWC PCIe controller
mirrors the DBI and ATU register space. It uses PARF_SLV_ADDR_SPACE_SIZE
register to get the size of the memory block to be mirrored and uses
PARF_DBI_BASE_ADDR, PARF_ATU_BASE_ADDR registers to determine the base
address of DBI and ATU space inside the memory block that is being
mirrored.
When a memory region which is located above the SLV_ADDR_SPACE_SIZE
boundary is used for BAR region then there could be an overlap of DBI and
ATU address space that is getting mirrored and the BAR region. This
results in DBI and ATU address space contents getting updated when a PCIe
function driver tries updating the BAR/MMIO memory region. Reference
memory map of the PCIe memory region with DBI and ATU address space
overlapping BAR region is as below.
|---------------|
| |
| |
------- --------|---------------|
| | |---------------|
| | | DBI |
| | |---------------|---->DBI_BASE_ADDR
| | | |
| | | |
| PCIe | |---->2*SLV_ADDR_SPACE_SIZE
| BAR/MMIO|---------------|
| Region | ATU |
| | |---------------|---->ATU_BASE_ADDR
| | | |
PCIe | |---------------|
Memory | | DBI |
Region | |---------------|---->DBI_BASE_ADDR
| | | |
| --------| |
| | |---->SLV_ADDR_SPACE_SIZE
| |---------------|
| | ATU |
| |---------------|---->ATU_BASE_ADDR
| | |
| |---------------|
| | DBI |
| |---------------|---->DBI_BASE_ADDR
| | |
| | |
----------------|---------------|
| |
| |
| |
|---------------|
Currently memory region beyond the SLV_ADDR_SPACE_SIZE boundary is not
used for BAR region which is why the above mentioned issue is not
encountered. This issue is discovered as part of internal testing when we
tried moving the BAR region beyond the SLV_ADDR_SPACE_SIZE boundary. Hence
we are trying to fix this.
As PARF hardware block mirrors DBI and ATU register space after every
PARF_SLV_ADDR_SPACE_SIZE (default 0x1000000) boundary multiple, program
maximum possible size to this register by writing 0x80000000 to it(it
considers only powers of 2 as values) to avoid mirroring DBI and ATU to
BAR/MMIO region. Write the physical base address of DBI and ATU register
blocks to PARF_DBI_BASE_ADDR (default 0x0) and PARF_ATU_BASE_ADDR (default
0x1000) respectively to make sure DBI and ATU blocks are at expected
memory locations.
The register offsets PARF_DBI_BASE_ADDR_V2, PARF_SLV_ADDR_SPACE_SIZE_V2
and PARF_ATU_BASE_ADDR are applicable for platforms that use Qcom IP
rev 1.9.0, 2.7.0 and 2.9.0. PARF_DBI_BASE_ADDR_V2 and
PARF_SLV_ADDR_SPACE_SIZE_V2 are applicable for Qcom IP rev 2.3.3.
PARF_DBI_BASE_ADDR and PARF_SLV_ADDR_SPACE_SIZE are applicable for Qcom
IP rev 1.0.0, 2.3.2 and 2.4.0. Update init()/post_init() functions of the
respective Qcom IP versions to program applicable PARF_DBI_BASE_ADDR,
PARF_SLV_ADDR_SPACE_SIZE and PARF_ATU_BASE_ADDR register offsets. Update
the SLV_ADDR_SPACE_SZ macro to 0x80000000 to set highest bit in
PARF_SLV_ADDR_SPACE_SIZE register.
Cache DBI and iATU physical addresses in 'struct dw_pcie' so that
pcie_qcom.c driver can program these addresses in the PARF_DBI_BASE_ADDR
and PARF_ATU_BASE_ADDR registers.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/linux-pci/20240814220338.1969668-1-quic_pyarlaga@quicinc.com
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Mayank Rana <quic_mrana@quicinc.com>
- Add Synopsys DWC macros for lane skew configuration (Yoshihiro Shimoda)
- Add struct rcar_gen4_pcie_drvdata to provide for future SoCs with
different initialization requirements (Yoshihiro Shimoda)
- Add .ltssm_control() method for SoC dependencies (Yoshihiro Shimoda)
- Add r8a779g0 (R-Car V4H) support (Yoshihiro Shimoda)
* pci/controller/rcar-gen4:
PCI: rcar-gen4: Add support for R-Car V4H
PCI: rcar-gen4: Add .ltssm_control() for other SoC support
PCI: rcar-gen4: Add struct rcar_gen4_pcie_drvdata
PCI: dwc: Add PCIE_PORT_{FORCE,LANE_SKEW} macros
- Use devm_clk_bulk_get_all() to get all the clocks from DT to avoid
writing out all the clock names (Manivannan Sadhasivam)
- Add DT binding and driver support for the SA8775P SoC (Mrinmay Sarkar)
- Refactor dw_pcie_edma_find_chip() to enable adding support for Hyper DMA
(HDMA) (Manivannan Sadhasivam)
- Enable drivers to supply the eDMA channel count since some can't auto
detect this (Manivannan Sadhasivam)
- Add HDMA support for the SA8775P SoC (Mrinmay Sarkar)
- Override the SA8775P NO_SNOOP default to avoid possible memory corruption
(Mrinmay Sarkar)
- Make sure resources are disabled during PERST# assertion, even if the
link is already disabled (Manivannan Sadhasivam)
- Vote for the CPU-PCIe ICC (interconnect) path to ensure it stays active
even if other drivers don't vote for it (Krishna chaitanya chundru)
- Add Operating Performance Points (OPP) to scale performance state based
on aggregate link bandwidth to improve SoC power efficiency (Krishna
chaitanya chundru)
- Return failure instead of success if dev_pm_opp_find_freq_floor() fails
(Dan Carpenter)
- Avoid an error pointer dereference if dev_pm_opp_find_freq_exact() fails
(Dan Carpenter)
- Prevent use of uninitialized data in qcom_pcie_suspend_noirq() (Dan
Carpenter)
* pci/controller/qcom:
PCI: qcom: Prevent use of uninitialized data in qcom_pcie_suspend_noirq()
PCI: qcom: Prevent potential error pointer dereference
PCI: qcom: Fix missing error code in qcom_pcie_probe()
PCI: qcom: Add OPP support to scale performance
PCI: Bring the PCIe speed to MBps logic to new pcie_dev_speed_mbps()
PCI: qcom: Add ICC bandwidth vote for CPU to PCIe path
PCI: qcom-ep: Disable resources unconditionally during PERST# assert
PCI: qcom-ep: Override NO_SNOOP attribute for SA8775P EP
PCI: qcom: Override NO_SNOOP attribute for SA8775P RC
PCI: epf-mhi: Enable HDMA for SA8775P SoC
PCI: qcom-ep: Add HDMA support for SA8775P SoC
PCI: dwc: Pass the eDMA mapping format flag directly from glue drivers
PCI: dwc: Skip finding eDMA channels count for HDMA platforms
PCI: dwc: Refactor dw_pcie_edma_find_chip() API
PCI: qcom-ep: Add support for SA8775P SOC
dt-bindings: PCI: qcom-ep: Add support for SA8775P SoC
PCI: qcom: Use devm_clk_bulk_get_all() API
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Bjorn Helgaas
Vincent Guittot
Shawn Lin
Krishna Chaitanya Chundru
Konrad Dybcio
Ziyue Zhang
Hans Zhang
Nam Cao
Mayank Rana
Niklas Cassel
Manivannan Sadhasivam
Frank Li
Shradha Todi
Richard Zhu
Krishna chaitanya chundru
Shashank Babu Chinta Venkata
Prudhvi Yarlagadda